铁阳极电化学对直接大红4BE模拟废水脱色

对铁阳极电化学处理直接大红4BE染料废水脱色率和脱色能耗的影响因素进行研究。考察了电流密度、染料溶液初始pH值、染料初始浓度和支持电解质Na2SO4浓度对脱色性能的影响。结果表明,电流密度、染料废水初始pH、染料初始浓度、支持电解质浓度对脱色率和脱色能耗产生较大影响。在电流密度1.667 mA/cm2、pH值6.54、染料浓度50mg/L、Na2SO4浓度0.01 mol/L、温度20℃、搅拌速度600 r/min、电解时间60 min条件下,脱色率达到92.1%,脱色能耗1.298 kWh/kg染料、铁阳极消耗量41 mg/400 mL染料模拟废水。     

漆酶对活性黑KN-B和直接大红染料的脱色性能

利用白腐真菌漆酶对活性黑KN-B和直接大红2种偶氮染料进行脱色实验。考察反应时间、加酶量、pH值、染料浓度、温度对脱色率的影响,研究了ABTS介体以及金属离子存在下的脱色效果,并分析了漆酶脱色的动力学性能以及其对偶氮染料的降解规律。结果表明,活性黑KN-B和直接大红脱色适宜条件为：反应时间为30 min,加酶量8 U/mL,pH=7,染料浓度分别为50 mg/L和80 mg/L,温度40~45℃。ABTS介体对酶促偶氮染料脱色没有明显促进作用。Fe²⁺对漆酶脱色有较强的抑制作用;Cu²⁺对漆酶催化活性黑KN-B促进作用较大,对直接大红影响较小。漆酶对2种染料的脱色反应符合米氏方程,其催化活性黑KN-B和直接大红染料的K_m值分别为114.81 mg/L,317.5 mg/L,v_max值分别为6.57 mg/（L·min）和26.0 mg/（L·min）。     

活性黑KN-B染料模拟废水电化学脱色

为进一步明确活性染料在可溶性阳极电化学体系中的脱色机理,以铝为牺牲阳极,不锈钢为阴极,在恒电流操作模式下,针对活性黑KN-B模拟废水,考察了电流密度、初始pH值、电解质种类及浓度、温度、染料浓度因素对染料脱色过程的影响。结果表明：(1)电流密度、电解液初始pH值、氯化钠电解质浓度、温度、染料浓度对染料溶液脱色效率影响显著,在一定实验条件下,染料溶液脱色率可达到88%;(2) 在不同pH的范围内,活性黑KN-B表现的脱色机理不同,pH 4～9为混凝与阴极还原脱色共同作用;pH＜4和＞9则表现为阴极还原脱色为主; (3) 氯化钠的加入在增强染料脱色的同时,也有助于芳环类物质的后续混凝去除。     

仿生矿化法制备壳聚糖/纳米CdS复合粒子对猩红B光催化降解研究

用仿生矿化法制备了壳聚糖/纳米CdS复合粒子,并用于可见光光催化降解猩红B染料模拟废水,系统地研究了染料初始浓度、pH值、催化剂投加量、光照情况和催化剂重复使用等因素对猩红B的光解脱色效率的影响。结果表明,当pH=3.0,催化剂投加量为0.7 g/L的条件下,对初始溶液为20 mg/L的猩红B模拟废水,60 min之内脱色率超过96%。酸性媒介比碱性媒介更有利于猩红B染料光解脱色。实验范围内Br^-、NO^-₃和Cl^-等无机阴离子,均对降解脱色有促进作用,其中NO₃^-对脱色作用促进最显著。处理前后的UV-Vis谱图分析表明猩红B在壳聚糖/纳米CdS复合粒子可见光光解处理过程中脱色是因为染料发生氧化光降作用。催化剂重复利用5次后,处理60 min对猩红B的脱色率仍可达到80.7%。     

铁阳极电凝聚处理活性黑KN-B染料废水

对铁阳极电凝聚处理活性黑KN-B染料废水过程进行了实验研究.考察了电流密度、染料溶液初始pH值、电介质浓度及种类、温度、染料浓度等因素对脱色效率的影响.结果表明,在一定实验条件下,活性黑KN-B模拟废水的脱色效率达93%;电流强度、染料浓度、电解液初始pH值及电解质的种类对染料溶液脱色效率影响显著,电解液温度、电解质的浓度对脱色效率的影响不明显;以铁为阳极的原位电凝聚处理活性黑KN-B模拟废水混凝过程中主要作用机理以吸附电性中和为主;电凝聚过程中活性黑KN-B在阴极上发生了还原反应.     

低频超声协同Fe-Ni-Mn/Al2O3催化降解酸性绿B的研究

采用低频超声与Fe-Ni-Mn/Al₂O₃催化剂协同降解偶氮染料酸性绿B模拟废水,考察染料初始浓度和pH值、催化剂、饱和气体及H₂O₂等因素对酸性绿B降解效果的影响, 结果表明：催化剂Fe-Ni-Mn/Al₂O₃与低频超声存在协同效应,催化剂的最佳投加量为6 g/L;酸性条件有利于染料的超声降解,当pH=3.8时, 可取得最佳的降解效果; 酸性绿B降解率随初始浓度的增大而降低,其优化初始浓度为100 mg/L,此外,在反应体系中鼓入饱和气体也可促进酸性B的降解,且影响顺序为混合气体(air+Ar)＞氧气＞氩气;在反应过程中投加H₂O₂有利于染料降解率的提高。在优化实验条件下降解150 min,酸性绿B色度去除率达到91.4%。     

双频超声辐射协同H2O2降解偶氮染料废水的研究

采用双频超声协同H₂O₂降解酸性绿20染料废水,考察超声功率密度、染料初始浓度和pH、饱和气体及H₂O₂投加量等因素对酸性绿20降解效果的影响,结果表明,在给定实验条件下,双频降解效果优于单频超声波,且降解率随超声功率密度的增大而增大。酸性条件有利于酸性绿20的降解,当染料废水初始pH=4可取得最佳的降解效果;酸性绿20的降解效率随染料初始浓度的增大而降低,其优化初始浓度为40 mg/L。在反应体系中通入空气并投加H₂O₂,可取得最佳的降解效果。在优化实验条件下, 采用双频超声协同H₂O₂降解5 h,酸性绿20的色度和TOC去除率分别为94.6%和36.3%;分析降解前后的紫外可见光谱图可知,酸性绿20并非完全被降解为CO₂和H₂O,而是生成一些小分子有机中间体。     

石墨烯泡沫包裹铁电极的制备及其在电解脱色染料中的应用研究

通过水热还原氧化石墨烯在铁电极表面原位生长石墨烯泡沫的方法制得了石墨烯泡沫包裹铁电极(GS-Fe电极),并将其应用于多种染料的电解脱色。结果表明:在相同电流密度下,GS-Fe电极的电解反应速率常数是铁电极的5倍;加入电解质对电解效率至关重要,其中NaCl是最有效的电解质;对甲烯蓝而言,最佳的电解条件为甲烯蓝初始质量浓度30mg/L、pH 5~7;GS-Fe电极可用于电解脱色刚果红、酸性蓝92和活性蓝R。电解脱色的机制推测主要为间接氧化,Cl~-被氧化成ClO~-,而后ClO~-氧化染料。GS-Fe电极可通过简单清洗再生,电解的脱色率几乎不受影响。     

Fe/活性炭多相类Fenton法湿式氧化罗丹明B废水的研究

采用自制的Fe/活性炭（Fe/AC）为催化剂,H₂O₂为氧化剂,组成多相类Fenton试剂催化降解罗丹明B染料废水。实验结果表明,在催化剂加入量为0.8 g/L,H₂O₂体积分数为0.3%,废水pH值为13,反应时间为30 min的条件下,质量浓度为200 mg/L的罗丹明B染料废水的脱色率达100%。反应动力学研究表明,罗丹明B脱色反应近似为一级反应,30℃时反应速率常数为0.02675 min^-1,表观活化能为69.47 kJ/mol。     

高铁酸盐对活性及分散染料的脱色研究

采用湿法制备了高铁酸钾(K₂FeO₄)氧化剂,研究了其对染料活性艳红X-3B(X-3B) 和分散蓝2BLN(2BLN)在不同pH条件下的脱色效果,并对Al₂ (SO₄)₃、K₂FeO₄及O₃对活性及分散染料的脱色效果进行了比较。结果表明：高铁酸钾对活性及分散染料的脱色效果明显, X-3B脱色率随pH的增加不断提高,2BLN脱色率在pH 6～10范围内无明显变化,在pH＝5时达到最大值。在X-3B及2BLN浓度同为100 mg／L,pH分别为10、5, K₂FeO₄浓度分别为100 mg／L和200 mg／L时,BLN及X-3B的脱色率分别达到92.3％和87.3％。在相同条件下,K₂FeO₄对活性艳红X-3B的脱色效果好于Al₂(SO₄)₃和O₃; 而K₂FeO₄对分散蓝2BLN的脱色效果虽比Al₂ (SO₄)₃稍差,但比臭氧的脱色效果要好。同时还研究了K₂FeO₄对活性及分散染料的脱色机理,结果表明： 高铁酸钾对X-3B的脱色依赖于K₂FeO₄的氧化作用,而对的2BLN的脱色则以絮凝为主。     

Treatment of Basic Red 29 dye solution using iron-aluminum electrode pairs by electrocoagulation and electro-Fenton methods

The aim of this study is the treatment of Basic Red 29 (BR29) dye solution using hybrid iron-aluminum electrodes by electrocoagulation and electro-Fenton methods. The effect of current density, initial pH, supporting electrolyte, H₂O₂, and initial dye concentration on dye removal efficiency was investigated, and the best experimental conditions were obtained. Time-coarse variation of UV-Vis spectra and toxicity and chemical oxygen demand (COD) removal were also examined at the best experimental conditions. Both systems were found very successful for the removal of BR29 dye. The removal efficiency of >95 % for BR29 dye solution was reached easily in a short time. At the best experimental conditions, for the initial BR29 concentration of 100 mg/L, >95 % BR29 dye and 71.43 % COD removal were obtained after 20 and 40 min of electrolysis, respectively. Additionally, toxicity results for electro-Fenton treatment of 100 mg/L BR29 were also very promising. According to the results obtained, although electro-Fenton is more effective, both systems can be used successfully to treat textile wastewater including dyes.     

Ce-PbO2/C电极的制备及其去除水中酸性红B

采用电沉积法制备铈修饰的PbO2/C电极,通过SEM、XRD、XPS及循环伏安对PbO2/C、Ce-PbO2/C电极进行表征,结果表明,Ce-PbO2/C电极比PbO2/C颗粒细小,表面均匀致密,电化学氧化能力较强,修饰电极中Ce以CeO2的形态存在。以Ce-PbO2/C为工作电极,电解浓度为1 000 mg/L的高盐酸性红B模拟活性染料废水,考察了电压、pH、电解质浓度、极间距对脱色率、氨氮去除率及COD去除率的影响。确定适宜工艺条件为:初始酸性红B溶液浓度为1 000 mg/L,pH值为6,电压10 V,电解时间1 h,电极间距1.5 cm,该条件下脱色率、氨氮去除率和COD去除率分别为99.98%、97.23%和90.17%。通过UV-Vis及GC-MS初步分析了降解过程可能存在的中间产物及降解途径。     

TiO2镀膜电极光电催化降解酸性紫红

采用溶胶-凝胶法在钛片上涂覆TiO2薄膜为电极,自行设计组装光电催化反应器,对酸性紫红染料废水进行光电脱色处理,探讨了光电反应的协同性并研究了初始染料浓度、电压、pH和电解质浓度对脱色反应的影响。结果表明,光化学催化和电化学氧化具有协同效应,单一紫外光催化和单一电催化酸性紫红的脱色率分别为44.27%和13.12%,而光电催化(紫外、外加电压10 V)的脱色率达到77.18%。初始浓度较低、电压适中、pH偏碱性时,酸性紫红废水脱色率较高;电解质对脱色反应有促进作用,且浓度越高,酸性紫红脱色率越高。     

FT-IR product study on the photo-oxidation of dimethyl sulphide in the presence of NOx—temperature dependence

The products of the OH radical-initiated oxidation of dimethyl sulphide (DMS) have been investigated as a function of temperature (284, 295, and 306 K) and different initial NO_x (NO+NO₂) concentrations: initial NO was varied between 434 and 2821 ppb and NO₂ between 135 and 739 ppb. The experiments were performed at 1000 mbar total pressure in synthetic air using the photolysis of H₂O₂ as the OH-radical source and FT-IR spectroscopy to monitor reactants and products. The major sulphur-containing products identified were SO₂, dimethyl sulphoxide (DMSO), dimethyl sulphone (DMSO₂), methane sulphonic acid (MSA), methane sulphonyl peroxynitrate (MSPN) and OCS. The variation of the product yields with temperature and NO_x concentration are consistent with the occurrence of both addition and abstraction channels in OH radical-initiated oxidation of DMS. Distinct trends in the yields of the various products have been observed as a function of temperature, initial NO_x conditions and also reaction time as NO is consumed in the system. Increasing the initial NO concentration was found to depress the DMSO, SO₂ and OCS formation yields and enhance those of DMSO₂, MSA and MSPN. The yield–time behaviour of DMSO₂ is supportive of a formation mechanism involving addition of O₂ to a (CH₃)₂SOH adduct, formed via the addition channel, followed by sequential reactions with NO and O₂. The mechanisms controlling the concentration–time profiles of the individual products under the present experimental conditions are discussed in detail and consideration is given to possible implications for the photo-oxidation of DMS under ambient conditions.     

电解质种类对电催化氧化降解苯酚的影响

研究了不同电解质对有机物电催化氧化性能的影响。以高温热解法制备了Ti/SnO2+Sb2O3阳极,用SEM和XRD对电极结构进行了表征。以苯酚为目标有机物,考察了Na2SO4、NaCl和NaNO33种不同电解质对苯酚降解效果的影响。用循环伏安法研究了苯酚在不同支持电解质条件下的电化学行为。采用碘量法测定了在不同电解质溶液中氧化性物质的生成量。研究结果表明,电极的活性涂层主要由SnO2和微量的Sb2O3组成,均匀完整地覆盖住了Ti基体表面。以NaCl为支持电解质时苯酚降解效果明显优于用Na2SO4、NaNO3为支持电解质,并且苯酚的降解主要以电极表面电化学生成的HClO和ClO-的间接化学氧化为主。以Na2SO4为支持电解质时有利于降低和稳定槽电压。在3种电解质条件下,苯酚的降解均遵循一级反应动力学规律。在降解过程中NaCl溶液中生成的氧化性物质浓度最大,且随降解时间延长逐渐增大。     

US/Zn~0体系降解水中的对硝基苯甲酸

为高效去除水体中的对硝基苯甲酸、开发新型水处理技术,提出以超声与单质锌联用降解水中的对硝基苯甲酸。考察了锌投加量、溶液初始pH、声功率及溶液初始浓度对拟一级反应速率常数(k0US/Zn)的影响,比较了US、Zn0和US/Zn03体系下的降解常数,并对US/Zn0体系的降解机理进行了初探。结果表明,以上4种因素对k0US/Zn均有很大影响,k0US/Zn分别在溶液初始pH为5、声功率为120 W、溶液初始浓度为0.04 mmol/L时达到最大值,且随着锌投加量的增加而增加。超声与单质锌在降解对硝基苯甲酸的过程中存在很好的协同作用,在最优条件下,k0US/Zn=0.052 min-1,分别是单独超声降解及单独锌降解的21.5倍和2.53倍。在联用体系中,主要是依靠OH·氧化及单质锌还原的相互加强来去除对硝基苯甲酸。     

旋转填料床/柠檬酸盐法吸收-解吸SO2

提出采用旋转填料床结合柠檬酸盐法脱除烟气中SO2的方法,考察了旋转填料床转子转速、液气比、初始柠檬酸根浓度和初始pH值等因素对脱硫效率的影响。结果表明,采用超重力法超重机转子转速为1 000 r/min、液气比为7L/m3、初始柠檬酸根浓度为1.5 mol/L、吸收液的初始pH值为5.0,脱硫效率稳定在99%左右。研究了水蒸气汽提法解吸SO2时初始柠檬酸根浓度、初始pH值、SO2浓度、富液流量和水蒸气流量对解吸效率的影响,得出了影响SO2解吸率的基本规律,并进行了分析。通过实验证明该方法在技术上是可行的,具有良好的应用前景。     

Kinetic behavior of anti-inflammatory drug ibuprofen in aqueous medium during its degradation by electrochemical advanced oxidation

The electrochemical abatement of the drug ibuprofen (2-(4-isobutylphenyl)propionic acid) from aqueous solution has been carried out by anodic oxidation. The electrolyses have been performed at constant current using a small, undivided cell equipped with a Pt or thin-film boron-doped diamond (BDD) anode and a carbon-felt cathode. The results have shown that ibuprofen has been destroyed under all the conditions tested, following pseudo-first-order kinetics; however, BDD enables higher removal rates than Pt, because the former produces greater quantity of ^?OH. Using BDD anode, the pseudo-first-order rate constant increased with applied current and when NaCl replaced Na₂SO₄ as supporting electrolyte, while it is almost unaffected by ibuprofen concentration. Mineralization of ibuprofen aqueous solutions was followed by total organic carbon (TOC) measurements. After 8 h of electrolysis, TOC removal varied from 91 % to 96 % applying a current in the range of 50–500 mA. The reaction by-products were quantified by chromatographic techniques, and in particular, aliphatic acids (oxalic, glyoxylic, formic, acetic, and pyruvic) have been the main intermediates formed during the electrolyses. The absolute rate constant for the oxidative degradation of ibuprofen have also been determined, by competition kinetic method, as 6.41?×?10⁹ M^?1?s^?1.