Evaluation of photolysis and hydrolysis of atrazine and its first degradation products in the presence of humic acids

Relative importance of hydrolysis and photolysis of atrazine and its degradation products in aqueous solutions with dissolved humic acids (HA) has been assessed under exposure to sunlight and under UV irradiation. Quantum yield for direct photolysis of atrazine at 254 nm was 0.037 mol photon(-1), the reaction order was 0.8. Atrazine, desethylatrazine and desisopropylatrazine converted to their 2-hydroxy analogs with rate constants 0.02-0.08 min(-1) in clear solutions, while addition of HA (300 mg L(-1)) caused a 10-fold increase in rate constants. Hydroxyatrazine was not degraded. No evidence of photo-Fenton reaction was found. Under exposure to solar light, atrazine, desethylatrazine and desisopropylatrazine were converted to 2-hydroxy analogs only at pH 2 because of acid hydrolysis and possible contribution of photolysis. At lower HA concentration, only their light-shielding effect was noticed, while at higher concentrations, HA-catalysed hydrolysis prevailed. Hydroxyatrazine concentration diminished at all pH values in solutions without HA exposed to sunlight.     

UV/ozone degradation of gaseous hexamethyldisilazane (HMDS)

As a carcinogen, hexamethyldisilazane (HMDS) is extensively adopted in life science microscopy, materials science and nanotechnology. However, no appropriate technology has been devised for treating HMDS in gas streams. This investigation evaluated the feasibility and effectiveness of the UV (185+254nm) and UV (254nm)/O(3) processes for degradation of gaseous HMDS. Tests were performed in two batch reactors with initial HMDS concentrations of 32-41mgm(-3) under various initial ozone dosages (O(3) (mg)/HMDS (mg)=1-5), atmospheres (N(2), O(2), and air), temperatures (28, 46, 65 and 80 degrees C), relative humilities (20%, 50%, 65%, 99%) and volumetric UV power inputs (0.87, 1.74, 4.07 and 8.16Wl(-1)) to assess their effects on the HMDS degradation rate. Results indicate that for all conditions, the decomposition rates for the UV (185+254nm) irradiation exceeded those for the UV (254nm)/O(3) process. UV (185+254nm) decompositions of HMDS displayed an apparent first-order kinetics. A process with irradiation of UV (185+254nm) to HMDS in air saturated with water at temperatures of 46-80 degrees C favors the HMDS degradation. With the condition as above and a P/V of around 8Wl(-1), k was approximately 0.20s(-1) and a reaction time of just 12s was required to degrade over 90% of the initial HMDS. The main mechanisms for the HMDS in wet air streams irradiated with UV (185+254nm) were found to be caused by OH free-radical oxidation produced from photolysis of water or O((1)D) produced from photolysis of oxygen. The economic evaluation factors of UV (185+254nm) and UV (254nm)/O(3) processes at different UV power inputs were also estimated.     

Degradation of ampicillin antibiotic in aqueous solution by ZnO/polyaniline nanocomposite as photocatalyst under sunlight irradiation

PURPOSE AND METHOD: ZnO/polyaniline nanocomposite in core-shell structure was prepared by the synthesis and adsorption of polyaniline chains on the structure of ZnO nanoparticles. Fourier transform infrared and ultraviolet-visible (UV-Vis) spectroscopy, X-ray diffraction patterns, field emission scanning electron microscopy, and transmission electron microscopy were used to characterize the composition and structure of the nanocomposite. The nanocomposite was used as an active photocatalyst for photodegradation and removal of ampicillin in aqueous solution. RESULTS: UV-Vis spectroscopy studies showed that ZnO/polyaniline nanocomposite absorbs visible light irradiation as well as ultraviolet spectrum, and therefore, it can be photoactivated under visible and ultraviolet lights. The photocatalytic activity of ZnO/polyaniline nanocomposite in degradation of ampicillin molecules in aqueous solution under natural sunlight irradiation was evaluated and compared with that of ZnO nanoparticles and pristine polyaniline. The ZnO/polyaniline core-shell nanocomposite exhibited higher photocatalytic activity compared to ZnO nanoparticles and pristine polyaniline. The effect of operating conditions (pH, ZnO/polyaniline nanocomposite dosage, and ampicillin concentration) in the photocatalytic degradation of ampicillin using ZnO/polyaniline nanocomposite was investigated. The optimum conditions for maximum efficiency of ampicillin degradation under 120 min sunlight irradiation were found as 10 mg L(-1) dosage of ZnO/polyaniline nanocomposite, ampicillin concentration of 4.5 mg L(-1), and solution pH?=?5. Under optimum operating conditions, degradation efficiency was reached to 41% after 120 min of exposure to the sunlight irradiation.     

Photodegradation of the novel fungicide fluopyram in aqueous solution: kinetics,transformation products,and toxicity evolvement

The aqueous photodegradation of fluopyram was investigated under UV light (λ?≥?200 nm) and simulated sunlight irradiation (λ?≥?290 nm). The effect of solution pH, fulvic acids (FA), nitrate (NO₃ ^?), Fe (III) ions, and titanium dioxide (TiO₂) on direct photolysis of fluopyram was explored. The results showed that fluopyram photodegradation was faster in neutral solution than that in acidic and alkaline solutions. The presence of FA, NO₃ ^?, Fe (III), and TiO₂ slightly affected the photodegradation of fluopyram under UV irradiation, whereas the photodegradation rates of fluopyram with 5 mg L^?1 Fe (III) and 500 mg L^?1 TiO₂ were about 7-fold and 13-fold faster than that without Fe (III) and TiO₂ under simulated sunlight irradiation, respectively. Three typical products for direct photolysis of fluopyram have been isolated and characterized by liquid chromatography tandem mass spectrometry. These products resulted from the intramolecular elimination of HCl, hydroxyl-substitution, and hydrogen extraction. Based on the identified transformation products and evolution profile, a plausible degradation pathway for the direct photolysis of fluopyram in aqueous solution was proposed. In addition, acute toxicity assays using the Vibrio fischeri bacteria test indicated that the transformation products were more toxic than the parent compound.     

Photodegradation of the herbicide EPTC and the safener dichlormid, alone and in combination

Photodegradation of the herbicide EPTC (S-ethyl-N, N-dipropylthiocarbamate), and the safener dichlormid (2,2-dichloro-N, N-diallylacetamide) has been examined in methanol and in water solutions. Irradiation of EPTC and dichlormid with UV light at 254 nm caused rapid degradation in both media. Remarkable and gradual changes in color of EPTC irradiated solution was observed from clear to yellow then to intense orange. EPTC half-life of elimination in water was 14.0, and 18.5 min, and in methanol 37.2 and 32.2 min, when irradiated with and without dichlormid, respectively. There was significant difference between rate of EPTC degradation in water and methanol in the presence or in the absence of dichlormid. Negligible degradation of EPTC or dichlormid at > 290 nm was observed. Photoproducts were separated and identified using GC or/and thin-layer chromatography then identified using mass spectrometry. It appeared that some products have high molecular weight that formed as a result of dimerization. This is possibly a result of the coupling of radicals that formed through EPTC degradation. The cleavage of C-S and C-N bonds accounted for the formation of these radicals. Gradual dealkylation of the acid chains of EPTC has also occurred. EPTC-sulfoxide, EPTC-sulfone, Propylamine and dipropylamine were detected as photoproducts of EPTC at 254 nm. Dichlormid pathways of degradation at 254 nm were characterized as dechlorination, dealkylation, and hydrolysis both in water and methanol. The findings showed that dichlormid did not significantly affect EPTC photodegradation either at 254 nm or at > 290 nm. The biological/toxicological properties of the photoproducts need further study, particularly the dimer compounds.     

Photodegradation of polychlorinated dibenzo-p-dioxins and dibenzofurans in aqueous solutions and in organic solvents

Aqueous solutions of selected polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) were prepared using a generator column and exposed to UV (300 nm) light in the laboratory and to sunlight in an outdoor environment. In the laboratory, additional exposures were also carried out using 60% acetonitrile/water solutions. At 300 nm di- and tetra PCDDs had higher first-order photodegradation rate constants in 60% acetonitrile/water than in pure water. The solvent effect was reversed for PCDFs. These results may be a reflection of the higher polarity of PCDFs compared to PCDDs. In both the indoor and outdoor exposures photodegradation rates decreased with increasing concentrations of chlorination. However, OCDF exposed to 300 nm light in 60% acetonitrile/water and to sunlight in pure water photodegraded more rapidly than tetra CDF. Photolysis rates in sunlight were considerably slower (t(1/2) of 6.4-23 h) than photolysis rates at 300 nm in the laboratory (t(1/2) of 4.3-680 min), reflecting the lower intensity of sunlight in the 300 nm region of the UV/Vis spectrum. The extent of dechlorination of the PCDDs/PCDFs was less than 20% and reductive dechlorination does not appear to be a major process in the photodegradation of PCDDs/PCDFs in aqueous solutions.     

Phototransformation of ibuprofen and ketoprofen in aqueous solutions

The UV (254 nm) and UV/VUV (254/185 nm) photolysis of two anti-inflammatory drugs, ibuprofen and ketoprofen, have been studied in aqueous solutions as a possible process for the removal of non-biodegradable compounds.We have examined the effects of dissolved oxygen and initial target concentration. Upon irradiation at 254 nm, the decomposition rate of ketoprofen is almost forty times higher as it of ibuprofen whilst VUV irradiation only increased the ibuprofen decomposition rate. The presence of dissolved oxygen accelerated the photodegradation of ibuprofen, whereas no effect was observed on the degradation of ketoprofen. The maximum quantum yield for the phototransformation was 0.2. The rate of mineralization in both cases was ∼60%, even after 1 h of treatment and this suggests the formation of stable by-products which were identified using GC-MS and HPLC-MS, respectively.     

Kinetic and chemical assessment of the UV/H2O2 treatment of antiepileptic drug carbamazepine

The UV/H2O2-induced degradation of carbamazepine, a worldwide used antiepileptic drug, recently found as contaminant in many municipal sewage treatment plant (STP) effluents and other aquatic environments, is investigated. The oxidation treatment caused an effective removal of the drug. At complete abatement of the substrate after 4 min treatment, a 35% value of removed total organic carbon (TOC) was obtained. A kinetic constant of (2.05+/-0.14) x 10(9) lmol(-1)s(-1) was determined for OH radical attack to carbamazepine in the UV/H2O2 process. Preparative TLC of the reaction mixture led to the isolation of acridine-9-carboxaldehyde as a reaction intermediate. HPLC and GC/MS analysis indicated formation of small amounts of acridine, salicylic acid, catechol and anthranilic acid among the reaction products. Under the same reaction conditions, synthetically prepared 10,11-epoxycarbamazepine was easily degraded to acridine as main product, suggesting that this epoxide is a likely intermediate in the oxidative conversion of carbamazepine to acridine. Under sunlight irradiation, carbamazepine in water underwent slow degradation to afford likewise acridine as main product. In view of the mutagenic properties of acridine, these results would raise important issues concerning the possible environmental impact of carbamazepine release through domestic wastewaters and support the importance of prolonged oxidation treatments to ensure complete degradation of aromatic intermediates.     

Ag／ZnO光催化降解甲基对硫磷研究

描述了掺杂体系Ａｇ／ＺｎＯ用于甲基对硫磷水溶液光催化降解,有氧存在下,经ＵＶ照射对甲基对硫磷光降解是有效的,并讨论了影响光降解中甲基硫磷诸因素,初步探讨了光降解机理和动力学,起始降解物为Ｃ２Ｈ６Ｐ＾＋Ｓ和Ｏ２ＮＨ４Ｏ,且是一级反应,半衰期为１．８２ｍｉｎ。     

腐殖酸和铁对阿特拉津光降解影响的研究

为考察除草剂在水体中的自净性能,对模拟太阳光(λ> 290 nm)下腐殖酸和铁元素对阿特拉津的光化学降解进行了研究。结果表明,单独辐照阿特拉津几乎不降解。在分别加入3、5和10 mg/L的腐殖酸时,阿特拉津的降解率分别为34.36 %、40.74%和15.66 %;在Fe(Ⅲ)投加量从0.01 mmol/L增加到0.2 mmol/L时,阿特拉津的降解率从24.36 %增加到34.97 %。而在当腐殖酸与铁共存时,阿特拉津降解率则进一步提高。紫外可见光谱和荧光光谱均表明,腐殖酸-铁络合物的形成及其光化学作用,促进了阿特拉津的降解。     

Occurrence and removal of endocrine disrupting chemicals in wastewater

This paper discusses the occurrence and removal of endocrine disrupting chemicals (EDCs) in Horsham sewage treatment plant (STP), West Sussex, UK. Photodegradation aided by a catalyst (TiO(2)) was studied for its efficiency of removing EDCs from wastewater. The degradation of estrone and 17beta-estradiol under natural sunlight followed a pseudo-first-order kinetics, with a rate constant of 0.01h(-1). The degradation by sunlight is also independent of initial chemical concentration, suggesting some potential of using this environmentally friendly method for waste minimisation. In comparison, more efficient degradation was observed with UV irradiation (253nm), with the rate constants being increased to 2.7 and 2.5h(-1) for the two compounds. Subsequent application of the photocatalysis method to real effluent treatment at Horsham STP was successful, as demonstrated by the non-detection of the target compounds following treatment.     

Photocatalytic Treatment of RDX Wastewater with Nano-Sized Titanium Dioxide (5 pp)

Background, Aim and Scope The polynitramines, hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), are important military explosives and regulated toxic hazardous compounds. Production, testing and use of the compounds has resulted in numerous acres of contaminated soils and groundwater near many munitions facilities. Economical and efficient methods for treatment of wastewater and cleanup of soils or groundwater containing RDX and HMX are needed. This study focuses on the photocatalytic treatment of RDX wastewater with nano-sized titanium dioxide (nano-TiO2) under simulated sunlight, whose intensity and wavelength are similar to that of the real sunlight in Xi'an at noon. The objective is to determine the potential for RDX destruction with nano-TiO2 in aqueous solution. Materials and Methods: An activated carbon fiber (ACF) cloth-loaded with nano-TiO2 was put into the RDX containing solution, and the concentration of RDX was measured (by HPLC–UV) at regular time intervals under simulated sunlight. Results: The RDX degradation percentage of the photocatalytic process is higher than that of Fenton oxidation before 80 min, equivalent after 80 min, and it reaches 95% or above after 120 min. The nano-TiO2 catalyst can be used repeatedly. Discussion: The photocatalytic degradation kinetics of RDX under simulated sunlight can be described by a first-order reaction kinetics equation. The possible degradation mechanism of RDX was presented and the degradation performance was compared with that of biological method. Conclusions: It was demonstrated that the degradation of RDX wastewater is very effective with nano-TiO2 as the photocatalytic catalyst under simulated sunlight. The efficiency of the nano-TiO2 catalyst for RDX degradation under simulated sunlight is nearly identical to that of Fenton oxidation. Recommendations and Perspectives: To date, a number of catalysts show poor absorption and utilization of sunlight, and still need ultraviolet light irradiation during wastewater degradation. The nano-TiO2 used in the described experiments features very good degradation of RDX under simulated sunlight, and the manufacturing costs are rather low (around 10 Euro/m2). Moreover, the degradation efficiency is higher compared to that of the biological method. This method exhibits great potential for practical applications owing to its easiness and low cost. If it can be applied extensively, the efficiency of wastewater treatment will be enhanced greatly.     

Transformation of sulfaquinoxaline by chlorine and UV light in water: kinetics and by-product identification

Sulfaquinoxaline (SQX) is an antimicrobial of the sulfonamide class, frequently detected at low levels in drinking and surface water as organic micropollutant. The main goal of the present study is the evaluation of SQX reactivity during chlorination and UV irradiations which are two processes mainly used in water treatment plants. The SQX transformation by chlorination and UV lights (254 nm) was investigated in purified water at common conditions used for water disinfection (pH =?7.2, temperature =?25 °C, [chlorine] =?3 mg L^?1). The result shows a slow degradation of SQX during photolysis compared with chlorination process. Kinetic studies that fitted a fluence-based first-order kinetic model were used to determine the kinetic constants of SQX degradation; they were equal to 0.7?×?10^?4 and 0.7?×?10^?2 s^?1corresponding to the half time lives of 162 and 1.64 min during photolysis and chlorination, respectively. In the second step, seven by-products were generated during a chlorination and photo-transformation of SQX and identified using liquid chromatography with electrospray ionization and tandem mass spectrometry (MS-MS). SO₂ extrusion and direct decomposition were the common degradation pathway during photolysis and chlorination. Hydroxylation and isomerization were observed during photodegradation only while electrophilic substitution was observed during chlorination process.     

Photodegradation of the steroid hormones 17beta-estradiol (E2) and 17alpha-ethinylestradiol (EE2) in dilute aqueous solution

The photochemical transformation of natural estrogenic steroid 17beta-estradiol (E2) and the synthetic oral contraceptive 17alpha-ethinylestradiol (EE2) has been studied in dilute non buffered aqueous solution (pH 5.5-6.0) upon monochromatic (254 nm) and polychromatic (lambda>290 nm) irradiation. Upon irradiation at 254 nm, the quantum yields of E2 and EE2 photolysis were similar and evaluated to be 0.067+/-0.007 and 0.062+/-0.007, respectively. Upon polychromatic excitation, and by using phenol as chemical actinometer, the photolysis efficiencies have been determined to be 0.07+/-0.01 and 0.08+/-0.01 for E2 and EE2, respectively. For both estrogens, photodegradation by-products were identified with GC/MS and LC/MS. In a first step, a model compound--5,6,7,8-tetrahydro-2-naphthol (THN)--, which represents the photoactive phenolic group, was used to obtain basic photoproduct structural informations. Numerous primary and secondary products were observed, corresponding to hydroxylated phenolic- or quinone-type compounds.     

Degradation of aquatic humic material by ultraviolet light

Natural humic water was treated with ultraviolet (UV) light and UV + hydrogen peroxide (UV/H₂O₂. The effects on the dissolved organic carbon content (DOC), the UV-absorbance at 254 nm (UV-abs.), the molecular size distribution, pH, and mutagenic activity were monitored, and the identity and concentrations of the most abundant gas chromatographable organic degradation products were determined.

The DOC content and the UV-abs. of the water decreased substantially during treatment with UV/H₂O₂. The decreases were dependent on the time of irradiation (UV dose) as well as on the H₂O₂ dose applied. The humus macromolecules were degraded to smaller fragments during irradiation. At higher UV doses, however, part of the dissolved organic matter (DOM) was found to precipitate, probably as a result of polymerization. Oxalic acid, acetic acid, malonic acid, and n-butanoic acid were the most abundant degradation products detected. These acids were found to account for up to 20% and 80% of the DOM in UV- and UV/H₂O₂-treated waters, respectively. No mutagenic activity was generated by the UV irradiation or the UV/H₂O₂ treatment. It is further concluded that the substantial mutagenic activity formed during chlorination of humic waters cannot be decreased by using UV irradiation as a pretreatment step.     

Kinetic studies of endosulfan photochemical degradations by ultraviolet light irradiation in aqueous medium

Kinetic studies of endosulfan photochemical degradation in controlled aqueous systems were carried out by ultraviolet light irradiation at lambda = 254 nm. The photolysis of (alpha + beta: 2 + 1) endosulfan, alpha-endosulfan and beta-endosulfan were first-order kinetics. The observed rate constants obtained from linear least-squares analysis of the data were 1 x 10(-4) s(-1); 1 x 10(-4) s(-1); and 2 x 10(-5) s(-1), respectively, and the calculated quantum yields (phi) were 1, 1 and 1.6, respectively. Preliminary differential pulse polarographic (DPP) analysis allowed to observe the possible endosulfan photochemical degradation pathway. This degradation route involves the formation of the endosulfan diol, its transformation to endosulfan ether and finally the ether's complete degradation by observing the potential shifts.     

Effects of riboflavin on the phototransformation of benzo[a]pyrene

Riboflavin (Vitamin B2) is a natural dye-sensitizer habitually present in natural waters. Effects of riboflavin as photosensitizer on the transformation of benzo[a]pyrene (BaP) (10 microM) in the aqueous-organic solvent (water/acetonitrile/methanol 50/40/10) were investigated in this study. The photolysis half life of BaP in solution containing 50 microM riboflavin was 5 min, compared to 98 min in the absence of riboflavin. The rate of phototransformation of BaP increased as the concentration of riboflavin was raised from 10 microM to 100 microM under both natural sunlight and UVA irradiation. The half life of BaP in the presence of 50 microM riboflavin was 10.6 min and 43.1 min when exposed to visible range of natural sunlight and UVA irradiation respectively. Riboflavin decomposes under natural sunlight. Lumichrome, a principal photoproduct of riboflavin, was shown to photosensitize BaP under natural sunlight after photolysis of riboflavin. Our study indicated that other photoproducts from riboflavin, such as lumiflavin, were also involved in the phototransformation of BaP under sunlight when riboflavin diminished. The major photoproducts in the photolysis of BaP were identified as 1,6-benzo[a]pyrene-dione, 3,6-benzo[a]pyrene-dione, 6,12-benzo[a]pyrene-dione by using high performance liquid chromatography (HPLC). All these products were detected in the samples which were irradiated under different light sources and in the presence or absence of riboflavin. The possible phototransformation mechanism was discussed.     

Abiotic degradation of imazethapyr in aqueous solution

The photodegradation of imazethapyr [2-(4,5-dihydro-4-méthyl-4-(1-méthylethyl)-5-oxo-1H-imidazol-2-yl)-5-ethyl-3-pyridinecarboxylic acid] in aqueous solution in the presence of titranium dioxide (TiO2) and humic acids (HA) at different ratios of herbicide/TiO2 and herbicide/humic acids was studied at pH 7.0. Irradiation was carried out with polychromatic light using Heraeus apparatus equipped with xenon lamp to simulate sunlight having a spectral energy distribution similar to solar irradiation (>290 nm). The concentration of remaining herbicide was followed using a High Pressure Liquid Chromatograph (HPLC) equipped with UV detector at 230 nm. In pure aqueous solution imazethapyr degrades slowly and the photodegradation leads to the formation of two metabolites labelled A and B. The presence of TiO2 caused enhancement of the degradation rate. The presence of HA induced an increase of the photodegradation of the pesticide with respect to pure aqueous solution.     

Photocatalytic degradation of phenol by visible light-responsive iron-doped TiO2 and spontaneous sedimentation of the TiO2 particles

Fe-doped TiO₂ was prepared by the calcination of Fe_xTiS₂ (x = 0, 0.002, 0.005, 0.008, 0.01) and characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and UV–visible diffuse reflectance spectra. All the Fe-doped TiO₂ were composed of an anatase crystal form and showed red shifts to a longer wavelength. The activity of the Fe-doped TiO₂ for the degradation of phenol was investigated by varying the iron content during UV (365 nm) and visible light (405 nm and 436 nm) irradiation. The degradation rate depended on the Fe content and the Fe-doped TiO₂ was responsive to the visible light as well as the elevated activity toward UV light. The molar ratio of 0.005 was the optimum for both the UV and visible light irradiations. The result was discussed on the basis of the balance of the excited electron–hole trap by the doped Fe³⁺ and their charge recombination on the doped Fe³⁺ level. The Fe-doped TiO₂ (x = 0.005) was more active than P25 TiO₂ under solar light irradiation. The suspended Fe-doped TiO₂ spontaneously precipitated once the stirring of the reaction mixture was terminated.     

Photolysis of pharmaceuticals and personal care products in the marine environment under simulated sunlight conditions: irradiation and identification

The photochemical fate of 16 pharmaceuticals and personal care products (PPCPs) found in the environment has been studied under controlled laboratory conditions applying a sunlight simulator. Aqueous samples containing PPCPs at environmentally relevant concentrations were extracted by solid-phase extraction (SPE) after irradiation. The exposed extracts were subsequently analysed by liquid chromatography combined with triple quadrupole mass spectrometry (HPLC-MS/MS) for studying the kinetics of photolytic transformations. Almost all exposed PPCPs appeared to react with a half-life time (τ _1/2) of less than 30 min. For ranitidine, sulfamethoxazole, diclofenac, warfarin, sulfamethoxazole and ciprofloxacin, τ_1/2 was found to be even less than 5 min. The structures of major photolysis products were determined using quadrupole-time-of-flight mass spectrometry (QToF) and spectroscopic data reported in the literature. For diclofenac, the transformation products carbazol-1-yl-acidic acid and 8-chloro-9H-carbazol-1-yl-acetic acid were identified based on the mass/charge ratio of protonated ions and their fragmentation pattern in negative electrospray ionization (ESI^?-QTOF). Irradiation of carbamazepine resulted in three known products: acridine, carbamazepine-10,11-epoxide, and 10,11-dihydro-10,11-dihydroxy-carbamazepine, whereas acetaminophen was photolytically transformed to 1-(2-amino-5 hydroxyphenyl) ethenone. These photochemical products were subsequently identified in seawater or fish samples collected at sites exposed to wastewater effluents on the Saudi Arabian coast of the Red Sea.