Phenol removal from aqueous environments by natural & chemically modified kaolin clay

Natural, acid and base modified kaolin clays were studied for the sake of phenol and 4-chlorophenol removal from aqueous environments and their application to real ground and industrial wastewater samples. Scanning electron microscope (SEM), infrared spectroscopy (IR), X-ray diffraction (XRD), Thermo Gravimetric Analysis (TGA), Differential Thermal Analysis (DTA), and Surface area analysis were employed for characterization of the adsorbents microstructure. Operating factors such as adsorbent dose, solution pH, initial phenol concentration, and contact time were studied. The experimental data displayed that the increase of the adsorbent dose, contact time, and pH value from 2 to 7 increases the efficiency of the removal process. Optimal conditions for phenolic removal were; contact time of 300 min, primary phenol solution of 25 mg/L, pH 7 and 2.5 g/L as an appropriate adsorbent dose using crude (natural), acid modified and base modified kaolin clays. The higher phenolic removal efficiencies were obtained at 5 mg/L as 90, 97, 96.2%, respectively, for the adsorbents in the previously mentioned order. The adsorption capacity in the removal of phenol and 4-chlorophenol were 7.481 and 4.195, 8.2942 and 3.211, and 8.05185 and 18.565 mg/g, respectively, for the adsorbents in the same mentioned order. The adsorption equilibrium data were fitted and analyzed with four isotherm models, namely, Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich isotherm equations. The adsorption process of phenol on studied adsorbents was exothermic, spontaneous and thermodynamically favorable proved by the negative values of their thermodynamic parameters ΔH° and ΔG°. The correlation coefficient (R²) for all concentrations was higher than 0.94, which indicates that in the studied system, the data suitably fit the first-order kinetics. The % desorption capacity was amounted to 96%, 91.11%, and 87.06% of adsorbed phenol, respectively, for the adsorbents in the previous order using 0.1N NaOH and 10% V/V ethanol solutions as eluents at 25°C, indicating the reusability of the adsorbents. Kaolin and its modified forms can be introduced as eco-friendly and low-cost adsorbents in water remediation implementation.     

Fenton试剂与改性凹凸棒石联合处理微污染水中苯酚的实验研究

研究了Fenton试剂联合聚二甲基二烯丙基氯化铵（PDMDAAC）改性凹凸棒石对模拟微污染水中苯酚的去除效果。考察了pH值、反应时间、投加量、温度等因素对苯酚去除效果的影响。结果表明：先采用Fenton试剂氧化再用改性凹凸棒石吸附对微污染水中苯酚具有较好的去除效果,在pH=9、温度为25℃、改性凹凸棒石投加量为5g／L、吸附时间20min的条件下,苯酚去除率达98．2％。     

Exploitation of Trichoderma harzianum mycelial waste for the removal of rhodamine 6G from aqueous solution

The harvested mycelial waste of Trichoderma harzianum was used as an adsorbent for the removal of rhodamine 6G and was studied in batch mode. The effects of agitation time and initial dye concentration, adsorbent dosage and pH were examined. The study revealed that the amount of dye adsorbed (mgg(-1)) increased with increase in agitation time and reached equilibrium after 120 min, for dye concentrations of 10-50 mg L(-1). The adsorbent dosage of 1.0 g/50 mL and pH of 8.0 were found to be optimum for maximum dye removal. The batch mode adsorption data followed both the Langmuir and Freundlich isotherms. The pseudo first- and second-order rate kinetics were applied to the adsorbent system. The adsorption kinetics of rhodamine 6G showed that the pseudo-second-order kinetic model provided the best correlation of the equilibrium data. The study implies that it is possible to develop a dye removal system by using T. harzianum biomass, which occurs as sludge in waste stream of fermentation industries.     

LDO处理垃圾渗滤液中氮的实验研究

研究了复合金属氧化物（LDO）用于处理垃圾渗滤液中氮的可行性,并与传统吸附剂粉末活性炭（PAC）进行了比较,考察了投加量、振荡速度、吸附时间、吸附温度、pH等因素对处理效果的影响。结果表明,当垃圾渗滤液中总氮浓度为561mg/L、LDO投加量为6g/L、振荡速度为170r/min、吸附时间为60min、温度为25℃、pH值为11时,LDO对总氮的吸附量最高,达到41mg/g。在相同条件下,LDO对总氮的吸附量是PAC的2.5—3.5倍。     

分子印迹硅纳米改性氧化石墨烯复合材料的制备及其对双酚A的吸附研究

制备了分子印迹硅纳米-氧化石墨烯复合吸附材料,并研究了复合材料对双酚A(Bisphenol A,BPA)的吸附性能.实验结果表明:复合吸附材料对BPA的吸附在35min内达到吸附平衡,Langmuir等温线模型得出最大吸附容量约为338.3mg/g;相对于BPA的结构类似物,对BPA具有良好的选择吸附性能;在溶液pH接...     

Azadirachta indica leaf powder as an effective biosorbent for dyes: a case study with aqueous Congo Red solutions

In the present work, the leaves of Azadirachta indica (locally known as the Neem tree) in the form of a powder were investigated as a biosorbent of dyes taking aqueous Congo Red solution as a model system. The sorbent was made from mature Neem leaves and was investigated in a batch reactor under variable system parameters such as concentration of the aqueous dye solution, agitation time, adsorbent amount, pH, and temperature. An amount of 0.6 g of the Neem leaf powder (NLP) per litre could remove 52.0-99.0% of the dye from an aqueous solution of concentration 2.87 x 10(-2) mmol l(-1) with the agitation time increasing from 60 to 300 min. The interactions were tested with respect to both pseudo first-order and second-order reaction kinetics; the latter was found to be more suitable. Considerable intra-particle diffusion was found to occur simultaneously. The sorption process was in conformity with Langmuir and Freundlich isotherms yielding values of the adsorption coefficients in the following ranges: Freundlich n: 0.12-0.19, Kf: 0.1039-0.2648 L g(-1); Langmuir qm: 41.24-128.26 g kg(-1), b: 443.3-1898.0 l mmol(-1), which supported favourable adsorption. The Langmuir monolayer capacity (qm) was high and the values of the coefficient b indicated the equilibrium, dye + NLP = dye...NLP being shifted overwhelmingly towards adsorption. Thermodynamically, the sorption process was exothermic with an average heat of adsorption of -12.75 kJ mol(-1). The spontaneity of the sorption process was also confirmed by the favourable values of Gibbs energy (mean values: -1.09 to -1.81 kJ mol(-1)) and entropy of adsorption (range: -18.97 to -56.32 J mol(-1)K(-1)). The results point to the effectiveness of the Neem leaf powder as a biosorbent for removing dyes like Congo Red from water.     

Removal of phenol from aqueous solutions by adsorption

Experiments have been conducted to examine the liquid-phase adsorption of phenol from water by silica gel, HiSiv 3000, activated alumina, activated carbon, Filtrasorb-400, and HiSiv 1000. Experiments were carried out for the analysis of adsorption equilibrium capacities and kinetics. The adsorption isotherm model of the Langmuir-Freundlich type was the best to describe adsorption equilibrium data for phenol for the adsorbents studied. Results of kinetic experiments indicated that HiSiv 1000 had the highest rate of adsorption among the adsorbents studied and therefore more detailed studies were carried out with this adsorbent. The influence of particle size, temperature, and thermal regeneration on adsorption of phenol by HiSiv 1000 was evaluated. From particle size experiments it appeared that adsorption capacity of HiSiv 1000 did not change by changing the particle size, but the rate of adsorption decreased considerably by increasing the particle size. The effect of temperature on adsorption was studied by determining equilibrium isotherms for HiSiv 1000 at 25, 40, and 55 degrees C. The results showed that adsorption capacity decreased with increasing temperature. Thermal regeneration of HiSiv 1000 was performed at 360 degrees C. It was observed that adsorption capacity of HiSiv 1000 did not change after 14 regeneration cycles. Equilibrium experiments showed that the adsorption capacities of activated carbon and Filtrasorb-400 were several times higher than that of HiSiv 1000.     

花生壳对Cr（Ⅵ）的等温吸附模型研究

在花生壳吸附剂量为1.0g、pH2.0、温度30℃、振荡速度140r/min、吸附时间360min条件下,实验研究了不同初始浓度（50 mg/L、75 mg/L、100 mg/L、125 mg/L、150 mg/L）的Cr（Ⅵ）溶液等温吸附曲线。研究结果表明,Langmuir等温吸附模型符合得更好;该吸附是一个优先吸附过程;最大饱和吸附量为6.25mg/g。     

Effects of impurities on the removal of heavy metals by natural limestones in aqueous systems

Effects of impurities on the removal of heavy metals by natural limestones in aqueous solutions were studied by evaluating various factors including limestone concentration, pH, contact time and temperature. Solutions of Pb(II), Cd(II), Cu(II) and Zn(II), prepared from chloride reagents at a concentration of 10 mg/L, were studied in a batch method. Four natural limestone samples, collected from the Campanian-Maastrichtian limestone beds in Tunisia, were used as adsorbents. Sorption experiments indicated that high removal efficiencies could be achieved. Limestone samples containing impurities, such as silica, iron/aluminum oxides and different kinds of clay minerals, demonstrated enhanced sorption capacity, nearing 100% removal in some cases. Kinetic experiments showed that the sorption of metal ions occurred rapidly at a low coverage stage, and that solutions were nearly at equilibrium after 60 min. Data trends generally fit pseudo-second order kinetic, and intra-particle diffusion, models. The following conditions were found to promote optimum, or near-optimum, sorption of heavy metals: 1) contact time of more than 60 min, 2) pH = 5, 3) >3 g/L limestone concentration and 4) T = 35 °C. The results of this study suggest that the limestones from northern Tunisia, that contain higher amounts of silica and iron/aluminum oxides, are promising adsorbents for the effective removal of toxic heavy metals from wastewaters.     

Possible Utilization of Silica Gel Sludge for the Removal of Phenol from Aqueous Solutions: Laboratory Studies

This paper discusses the adsorption capacity of silica gel sludge for phenol removal from aqueous solution. Kinetic experiments showed that phenol adsorption was completed after 2 h. Adsorption isotherms were measured for phenol from aqueous solution onto silica gel sludge under various pHs and temperatures. Results showed that the adsorption capacities for phenol was increased as pH decreased from 6.5 to 2. Temperature also was found to affect the adsorption isotherm. As temperature increases from 30 to 50°C, the adsorption capacity increases. The adsorption equilibrium of phenol on silica gel sludge was described by the linear Freundlich and Langmuir models. Furthermore, results showed that the isotherm parameters fit both linearized Langmuir and Freundlich adsorption isotherms. The Freundlich and Langmuir parameters at optimum pH was found as K _f=2.89, 1/n=0.23 and K _d=22.0, q _m=7.98, respectively. Whereas, for those at optimum temperature it was observed as K _f=2.87, 1/n=0.16 and K _d=20.93, q _m=7.91, respectively.     

Application of a chemically modified green macro alga as a biosorbent for phenol removal

Phenol and substituted phenols are toxic organic pollutants present in tannery waste streams. Environmental legislation defines the maximum discharge limit to be 5–50 ppm of total phenols in sewers. Thus the efforts to develop new efficient methods to remove phenolic compounds from wastewater are of primary concern. The present work aims at the use of a modified green macro alga (Caulerpa scalpelliformis) as a biosorbent for the removal of phenolic compounds from the post-tanning sectional stream. The effects of initial phenol concentration, contact time, temperature and initial pH of the solution on the biosorption potential of macro algal biomass have been investigated. Biosorption of phenol by modified green macro algae is best described by the Langmuir adsorption isotherm model. Biosorption kinetics of phenol onto modified green macro algal biomass were best described by a pseudo second order model. The maximum uptake capacity was found to be 20 mg of phenol per gram of green macro algae. A Boyd plot confirmed the external mass transfer as the slowest step involved in the biosorption process. The average effective diffusion coefficient was found to be 1.44 × 10⁻⁹ cm²/s. Thermodynamic studies confirmed the biosorption process to be exothermic.     

Adsorption and transport of arsenic(V) in experimental subsurface systems

The adsorption and transport of As(V) in a heterogeneous, iron oxide-containing soil was investigated in batch and column laboratory experiments. The As(V) adsorbed rapidly to the soil over the first 48 h, but continued to adsorb slowly over the next several weeks, clearly indicating the potential for rate-limited transport. The equilibrium As(V) adsorption isotherm was markedly nonlinear, further indicating the potential for nonideal transport. A model developed for the adsorption of As(V) to hydrous ferric oxide (HFO) was able to predict the pH-dependent adsorption of As(V) to the soil in batch experiments within 0.116 to 0.726 root mean square error (RMSE). Arsenic(V) was significantly retarded in column transport experiments. The column transport experiments were modeled using the one-dimensional advection-dispersion equation, considering both linear and nonlinear adsorption equilibrium. Although the nonlinear local equilibrium model (NLLE, RMSE = 0.273) predicted the data better than the linear local equilibrium model (LLE, RMSE = 0.317), As(V) breakthrough occurred more rapidly than predicted by either model due to adsorption nonequilibrium. However, due to the presence of an irreversible or slowly desorbing fraction, the peak aqueous As(V) concentration (0.624 mg L(-1)) and the total amount of As(V) recovered (44%) was lower than predicted based on the two equilibrium models (NLLE and LLE). For the conditions used in this study [1 mg L(-1) As(V), pH 4.5 and 9,0-0.25 mM PO4, 0.53-1.6 cm min(-1) pore water velocity], the effect on As(V) mobility and recovery increased in the order pH < pore water velocity < PO4.     

草木灰对亚甲基蓝的吸附研究

本实验目的是研究草木灰对吸附亚甲基蓝的去除效果,探讨了亚甲基蓝初始量、吸附时间、pH值等对吸附效果的影响,并运用伪一级、伪二级反应动力学模型和Laugmuir、Freundlich等温线模型进行拟合。结果表明,草木灰对亚甲基蓝溶液的吸附在5 min~30 min速率比较快,约在65 min内达到吸附平衡,pH越大越有利于吸附,浓度在5mg/L时草木灰对亚甲基蓝的吸附最佳。与伪二级动力学曲线模型拟合效果较好,由Laugmuir等温线模型计算得出理论最大吸附容量Qm为2.275 mg/g,吸附性能优异。     

Application of cupuassu shell as biosorbent for the removal of textile dyes from aqueous solution

The cupuassu shell (Theobroma grandiflorum) which is a food residue was used in its natural form as biosorbent for the removal of C.I. Reactive Red 194 and C.I. Direct Blue 53 dyes from aqueous solutions. This biosorbent was characterized by infrared spectroscopy, scanning electron microscopy, and nitrogen adsorption/desorption curves. The effects of pH, biosorbent dosage and shaking time on biosorption capacities were studied. In acidic pH region (pH 2.0) the biosorption of the dyes were favorable. The contact time required to obtain the equilibrium was 8 and 18 h at 298 K, for Reactive Red 194 and Direct Blue 53, respectively. The Avrami fractionary-order kinetic model provided the best fit to experimental data compared with pseudo-first-order, pseudo-second-order and chemisorption kinetic adsorption models. The equilibrium data were fitted to Langmuir, Freundlich, Sips and Radke-Prausnitz isotherm models. For both dyes the equilibrium data were best fitted to the Sips isotherm model.     

Removal of Fe(II) from the wastewater of a galvanized pipe manufacturing industry by adsorption onto bentonite clay

Bentonite clay has been used for the adsorption of Fe(II) from aqueous solutions over a concentration range of 80-200 mg/l, shaking time of 1-60 min, adsorbent dosage from 0.02 to 2 g and pH of 3. The process of uptake follows both the Langmuir and Freundlich isotherm models and also the first-order kinetics. The maximum removal (>98%) was observed at pH of 3 with initial concentration of 100 mg/l and 0.5 g of bentonite. The efficiency of Fe(II) removal was also tested using wastewater from a galvanized pipe manufacturing industry. More than 90% of Fe(II) can be effectively removed from the wastewater by using 2.0 g of the bentonite. The effect of cations (i.e. zinc, manganese, lead, cadmium, nickel, cobalt, chromium and copper) on the removal of Fe(II) was studied in the concentration range of 10-500 mg/l. All the added cations reduced the adsorption of Fe(II) at high concentrations except Zn. Column studies have also been carried out using a certain concentration of wastewater. More than 99% recovery has been achieved by using 5 g of the bentonite with 3M nitric acid solution.     

Adsorption characteristics of Cu and Ni on Irish peat moss

Peat has been widely used as a low cost adsorbent to remove a variety of materials including organic compounds and heavy metals from water. Various functional groups in lignin allow such compounds to bind on active sites of peat. The adsorption of Cu(2+) and Ni(2+) from aqueous solutions on Irish peat moss was studied both as a pure ion and from their binary mixtures under both equilibrium and dynamic conditions in the concentration range of 5-100mg/L. The pH of the solutions containing either Cu(2+) or Ni(2+) was varied over a range of 2-8. The adsorption of Cu(2+) and Ni(+2) on peat was found to be pH dependent. The adsorption data could be fitted to a two-site Langmuir adsorption isotherm and the maximum adsorption capacity of peat was determined to be 17.6 mg/g for Cu(2+) and 14.5mg/g for Ni(2+) at 298 K when the initial concentration for both Cu(2+) and Ni(2+) was 100mg/L, and the pH of the solution was 4.0 and 4.5, respectively. Column studies were conducted to generate breakthrough data for both pure component and binary mixtures of copper and nickel. Desorption experiments showed that 2mM EDTA solution could be used to remove all of the adsorbed copper and nickel from the bed.     

Sorption of cadmium and zinc from aqueous solutions by zeolite 4A, zeolite 13X and bentonite

The sorption and desorption of cadmium and zinc on zeolite 4A, zeolite 13X and bentonite has been studied using batch sorption studies. Parameters such as equilibrium time, effect of pH and sorbent dose were studied. The sorbents exhibited good sorption potential for cadmium and zinc with a peak value at pH 6.0 and 6.5, respectively. The sorption followed the Freundlich sorption model. More than 70% sorption occurred within 20 min and equilibrium was attained at around 90 min for the three sorbents. The metals sorption by zeolite 4A was higher than that by zeolite 13X and bentonite. The desorption studies were carried out using NaCl solution and the effect of NaCl concentration on desorption was also studied. Maximum desorption of 76% for cadmium and 80% for zinc occurred with 10% NaCl.     

磁性活性炭吸附苯酚的初步研究

本文研究了磁性活性炭对苯酚的吸附性能;探讨了Cd2＋对苯酚在磁性活性炭上吸附的影响。目的是对磁性活性炭进行研究,以及为在实际废水中吸附处理苯酚提供参考。结果表明,磁性活性炭对苯酚的吸附过程符合拟二级动力学模型,R2为0.9935;与Freundlich吸附模型相比,Langmuir吸附模型能更好地描述磁性活性炭对苯酚的吸附行为;在不影响去除率的情况下,Cd2＋的存在使苯酚吸附处理最佳浓度由30 mg/L增大至50 mg/L;同时,Cd2＋对磁性活性炭和活性炭吸附苯酚分别具有促进和抑制作用。针对苯酚的吸附去除率,当无Cd2＋时,磁性活性炭的比活性炭的低10.65%～20.2%;当有Cd2＋时,磁性活性炭的比活性炭的高0.3%～7.71%。     

Platinum (IV) recovery from chloride solution by functionalized acrylic copolymers

Two acrylic adsorbents with different morphological structures and bearing amidoethylenamine and thiol groups were obtained and used for platinum sorption from chloride solution by the batch method. Physico-chemical parameters that influence adsorption such as initial Pt(IV) concentration, stirring time, pH, and adsorbent amount were investigated. The thermodynamic parameters of Pt(IV) sorption on the synthesized adsorbent were also evaluated based on Langmuir and Freundlich isotherms. Thermodynamic parameters estimated from Langmuir constants indicated that the adsorption is spontaneous, exothermic and there is a disordered state at the molecular level. The models used to analyze the sorption rate led to the conclusion that the most important step in the sorption of Pt(IV) could be both particle diffusion and chemical reaction of [PtCl₆]⁻ with amine functional groups. Thus, both the ion exchange and complex formation mechanisms can occur via nitrogen atoms in the recovery of Pt(IV) on the studied adsorbent.     

Attenuation of divalent toxic metal ions using natural sericitic pyrophyllite

The present study investigated the effectiveness of an inexpensive and ecofriendly alumino silicate clay mineral, sericitic pyrophyllite, as an adsorbent for the possible application in the removal of some divalent toxic metal cations such as Pb(2+), Cu(2+)and Zn(2+) from aqueous systems. Batch scale equilibrium adsorption studies were carried out for a wide range of initial concentration from 24.1 to 2410mumolL(-1) for lead, 78.65 to 7865mumolL(-1) for copper and 76.45 to 7645mumolL(-1) for zinc solutions. The removal of Pb(2+) was almost complete at low concentration (maximum lead removal capacity, LRC, 32mg of lead/g of pyrophyllite) with 10gL(-1) of adsorbent in a 30min equilibration time. The effects of temperature on adsorption of heavy metal ions were studied. The applicability of the Langmuir, Freundlich and Dubinin-Radushkevich adsorption models in each case of lead, copper and zinc adsorption was examined separately at different temperatures. The adsorption process was found to be endothermic and the Freundlich adsorption model was found to represent the data at different temperatures more suitably.