Preparation of MgO/B2O3 coatings by plasma spraying on SUS304 surface and effects of heat-resistant

This study mainly deals with the preparation of MgO/B₂O₃ coatings by plasma spraying on the SUS304 surface and the effects of heatresistant. The power materials of low thermal conductivity were selected to control the heat divergent performance of high temperature parts. The reticular micro-structure between the cover thermal layer and the substrate was prepared by using the plasma spraying method. The powder mixture of MgO and B₂O₃ were selected as spraying materials and the SUS304 was used as the substrate material. The MgO/B₂O₃ coating was prepared on the surface of the SUS304 to provide better cover thermal performance. The properties of the microstructures and the morphologies were studied by Optical Microscope, Scanning Electron Microscope, Electron Probe Microanalyzer, and X-ray Diffraction. The results showed that the cover thermal performance has been improved.     

Coating of γ-Al2O3 on the stainless steel substrate by electrophoretic deposition method

γ-Al₂O₃ coatings were prepared on aluminum-free stainless steel (SUS304) by electrophoretic deposition method. Both X-ray diffraction and scanning electron microscopy were used to study the crystalline structure and morphological features of the coatings. Themo gravimetry-differential termal analysis (TG-DTA) is used to study the thermo-chimerical reaction behavior of coatings. Catalytic activity of coatings is determined by degrading of NO_x. The results indicated that the thickness of the coatings onto SUS304 could reach 5 μm without any exfoliation at optimized conditions. Catalytic properties of samples coated by electrophoretic deposition method were highly enhanced as compared with that of samples prepared by the dip coating method.     

Pd/CZ/Al2O3催化剂的制备、表征与三效催化性能

以共浸渍法制得的氧化铝负载铈锆固溶体为载体,并浸渍贵金属Pd得到了Pd/CZ/Al₂O₃催化剂.实验结果表明,该催化剂在老化前后都表现出良好的三效催化活性,新鲜样品Pd/CZ/Al₂O₃活性与Pd/CZ相当,老化后样品前者优于后者.结合XRD,BET,TPR等表征手段,讨论了Pd/CZ/Al₂O₃的催化活性特别是高温老化后活性与其组成结构之间的内在关系,揭示了其老化后仍具有较高活性的主要原因在于保持了Pd与CZ/Al₂O₃复合载体之间的强相互作用(SMSI).     

MgO催化臭氧氧化降解苯酚机理研究

对氧化镁(MgO)催化臭氧氧化降解苯酚的机理进行了探讨,并验证其与现有的3种催化臭氧氧化机理的吻合性.同时,研究了羟基自由基(·OH)抑制剂对苯酚去除效果的影响,·OH的产生量,以及臭氧在该体系中的存在位置及苯酚在该体系中的作用.结果表明,O_3和MgO/O_3两种反应体系中都存在·OH,MgO/O_3体系中的·OH是O_3体系中的2.14倍.O_3和MgO/O_3体系中的·OH与臭氧浓度的比值分别为1.47×10~(-9)和3.15×10~(-9).苯酚在MgO催化臭氧氧化体系中起到了促进臭氧吸附在MgO表面的作用,臭氧吸附到MgO表面后,分解产生·OH,一部分释放在溶液中降解苯酚,一部分则留在其表面增加表面羟基密度.     

不锈钢201、304和316L在模拟污水管道反应器中的腐蚀

研究了作为污水管道局部修复材料的不锈钢201、304和316L在模拟污水管道反应器中的腐蚀行为.采用动电位法研究了第7、14、21、56 d这3种材料在全部浸没在污水或以2 d为周期交替浸没在污水两种条件下的腐蚀电位和腐蚀速率,采用电化学阻抗谱(EIS)研究了第56 d这3种材料的电极过程,利用扫描电镜(SEM)和能谱(EDS)分析了第56 d腐蚀点的形貌和成分.结果表明,在两种条件下304和316L的耐腐蚀性均好于201,腐蚀速率均小于201;3种不锈钢在交替浸没条件下的耐腐蚀性均优于全浸条件,在交替浸没条件下的腐蚀速率小于全浸条件;在304和316L的表面形成了局部点腐蚀,在201的表面形成了区域性腐蚀.     

Influence of coating method on catalyst activity of AgCl/Al2O3/SUS304 composite plate

The γ-Al₂0₃ and AgCl/Al₂0₃ catalyst powder were coated on a stainless steel substrate by dip coating and electrophoretic deposition method. And AgCl/Al₂0₃ catalyst was produced by three kinds of methods, and the difference between the NOx reduction catalysis of the coated sample was compared. XRD and SEM were used to study the crystalline structure and cross-section of the coatings. The coating of γ-Al₂0₃ with the thickness of 3-5 μm and AgCl/Al₂0₃ catalyst with the thickness of 5-9 μrn were made on the surface of SUS304 plate without exfoliation. The NOx conversion of the coated sample with catalyst was about 70% at the maximum.     

Synthesis and characteristic of polyaniline/Dy2O3 composites: Thermal property and electrochemical performance

A simple route of in situ polymerization by the chemical oxidation method was successfully employed to synthesize polyaniline/dysprosium oxide (PANI/Dy₂O₃) composites. The synthesized materials were characterized by Fourier transform infrared spectra and X-ray diffraction. The thermal stability of the composite was studied by thermogravimetry (TG). The electrochemical performance of the composites was investigated by cyclic voltammetry and alternating current impedance spectroscopy with a three-electrode system. TG results suggested that the thermal stability of PANI/Dy₂O₃ composites showed a tendency to first increase and then decrease with increasing Dy₂O₃ amount. Electrochemical experiments indicated that the composite electrodes showed a lower capacitance than that of pure PANI, which may be attributed to the interaction between PANI and Dy₂O₃ in the composites.     

二价铁催化过氧化氢-过硫酸钠再生活性炭可行性研究

利用二价铁(Fe~(2+))催化过氧化氢(H_2O_2)-过硫酸钠(Na_2S_2O_8)双氧化体系(ICHP)对被三氯乙烯(TCE)吸附饱和的20~40目粒状活性炭(AC)进行再生研究.同时,结合扫描电子显微镜(SEM)、能量散射光谱仪(EDS)、X射线光电子能谱仪(XPS)及氮气吸附-解吸技术等手段对再生前后的AC进行表征,进一步探讨影响再生效率的原因.结果表明,AC对TCE的吸附符合准一级动力学模型,等温吸附符合Freundlich模型.在TCE∶Fe~(2+)∶H_2O_2∶S_2O_2-8=1∶9.20∶59.79∶77.52(物质的量比)的条件下,AC再生效率约为50%.研究表明,AC的炭损失、比表面积、孔隙体积及孔隙面积的减小,是再生AC吸附能力低于原状AC的主要原因.利用ICHP再生的AC可以实现对TCE的有效吸附并达到AC重复使用的目的,具有很好的实用价值.     

Synthesis and characteristic of polyaniline/Dy2O3 composites：Thermal property and electrochemical performance

A simple route of in situ polymerization by the chemical oxidation method was successfully employed to synthesize polyaniline/dysprosium oxide (PANI/Dy₂O₃) composites. The synthesized materials were characterized by Fourier transform infrared spectra and X-ray diffraction. The thermal stability of the composite was studied by thermogravimetry (TG). The electrochemical performance of the composites was investigated by cyclic voltammetry and alternating current impedance spectroscopy with a three-electrode system. TG results suggested that the thermal stability of PANI/Dy₂O₃ composites showed a tendency to first increase and then decrease with increasing Dy₂O₃ amount. Electrochemical experiments indicated that the composite electrodes showed a lower capacitance than that of pure PANI, which may be attributed to the interaction between PANI and Dy₂O₃ in the composites.     

Preparation and characterization of Pd/Fe bimetallic nanoparticles immobilized on Al2O3/PVDF membrane: Parameter optimization and dechlorination of dichloroacetic acid

Using a liquid–solid phase inversion method, a hybrid matrix poly(vinylidene fluoride)(PVDF) membrane was prepared with alumina(Al2O3) nanoparticle addition. Pd/Fe nanoparticles(NPs) were successfully immobilized on the Al2O3/PVDF membrane, which was characterized by Scanning Electron Microscopy(SEM) and Transmission Electron Microscopy(TEM). The micrographs showed that the Pd/Fe NPs were dispersed homogeneously. Several important experimental parameters were optimized, including the mechanical properties, contact angle and surface area of Al2O3/PVDF composite membranes with different Al2O3 contents. At the same time, the ferrous ion concentration and the effect of hydrophilization were studied. The results showed that the modified Al2O3/PVDF membrane functioned well as a support. The Al2O3/PVDF membrane with immobilized Pd/Fe NPs exhibited high efficiency in terms of dichloroacetic acid(DCAA) dechlorination. Additionally, a reaction pathway for DCAA dechlorination by Pd/Fe NPs immobilized on the Al2O3/PVDF membrane system was proposed.     

等离子体场内CeO2催化降解甲醇的表面活性氧物种来源与作用研究

利用水热法制备了3种不同形貌(纳米棒、纳米颗粒、纳米立方体)的CeO_2催化剂,并通过比表面积测试(BET)、扫描电子显微镜(SEM)、拉曼光谱分析(Raman)、O_2程序升温脱附(O_2-TPD)手段表征其物理化学性质,结果发现,CeO_2纳米棒的表面氧空位和氧物种最多.等离子体与催化协同降解甲醇性能评价实验结果显示,CeO_2纳米棒展现出最好的催化性能.进一步设计实验(甲醇-TPD、不同气氛常温催化、催化剂内后置比较、O_3催化氧化)推测在等离子体场内CeO_2表面活性氧物种来源及其作用.结果表明:①在等离子体场内参与CeO_2表面催化反应的活性氧物种有两个来源,一是催化剂本身存在的表面氧物种,二是等离子体区域产生的短寿命物种及长寿命物种(主要是O_3),其中,O_3分解产生的活性氧物种是提高催化性能的主要因素.②不同形貌CeO_2由于表面氧空位含量不同,导致O_3在催化剂上分解产生的活性氧物种的量不同,最终影响等离子体催化性能.     

Study on methane conversion to syngas over nano Pt-CeO2-ZrO2/MgO catalysts: Structure and catalytic behavior of catalysts prepared by using ion exchange resin method

Nano Pt-Ce0₂-Zr0₂/MgO catalysts with 0.8 wt.% Pt, 3.0 wt.% Ce0₂ and 3.0 wt.% Zr0₂ were prepared by wet impregnation mothod. Support MgO was obtained using ion exchange resin method or using commercial MgO. S_BET, XRD, TEM and C0₂-TPD were used to characterize the supports and catalysts. CH₄-C0₂ reforming to synthesis gas was performed to test the catalytic behavior of the catalysts. The catalysts prepared using ion exchange resin exhibited more regular structure, more basic sites and higher stability of Pt and MgO than prepared from commercial MgO. At 1073 K, atmospheric pressure, and at high gas hourly space velocity of 36,000 mL/(g-hr) with a stoichiometric feed of CH₄ and C0₂, the catalyst supported on the MOH(GD)-IE showed a higher and more stable activity for CH₄-C0₂ reforming reaction than the catalyst prepared using commercial MgO. The characterisation results demonstrated that the high activity and stability of the catalyst stem from the high dispersion of Pt, the stable structure and the high resistance to carbon deposition on the catalyst.     

模拟酸雨对混凝土影响的研究

采用周期浸泡和喷淋试验等２种加速腐蚀试验方法,分别研究ＰＨ为１．０、３．５、５．６和ＰＨ为１．０、ＳＯ＾２－４为０、０．０６、０．１ｍｏｌ／Ｌ等６种模拟酸雨对混凝土的影响。     

Decomposition of hexachlorobenzene over Al2O3 supported metal oxide catalysts

Decomposition of hexachlorobenzene (HCB) was investigated over several metal oxides (i.e., MgO, CaO, BaO, La₂O₃, CeO₂, MnO₂, Fe₂O₃, and Co₃O₄) supported on Al₂O₃, which was achieved in closed system at a temperature of 300°C. Catalysts were prepared by incipient wetness impregnation with different metal oxides loading and impregnating solvents. The decomposition efficiency of different catalysts for this reaction depends on the nature of the metal oxide used, and Al₂O₃ supported La₂O₃ was found to be the most active one. Pentachlorobenzene (PeCB), and all tetrachlorobenzene (TeCB), trichlorobenzene (TrCB), and dichlorobenzene (DCB) isomers were detected after the decomposition reaction, indicating that the decomposition was mainly a dechlorination process. The detection of all lower chlorinated benzenes suggested the complexity of decomposition and the presence of more than one dechlorination pathway.     

Ti/Ti4O7阳极电化学氧化降解水中的美托洛尔

等离子喷涂法制备了钛基亚氧化钛电极(Ti/Ti_4O_7),以该电极为阳极,研究了电化学氧化法对水中美托洛尔的去除效果.考察了电流密度(5~25 mA·cm~(-2))、极板间距(5~25 mm)和初始浓度(3~50 mg·L~(-1))对美托洛尔电化学降解效率的影响;分析美托洛尔电化学降解过程中溶液总有机碳(TOC)和毒性的变化,鉴别反应中间产物并计算其毒性.研究表明:Ti/Ti_4O_7阳极电化学降解美托洛尔反应符合一级反应动力学规律(R20.95),降解效率随电流密度的增大而增大,随极板间距和初始浓度的增大而减小;TOC去除率在反应40 min后可达56.5%;反应过程中产生了质合比为266、250、223和207的中间产物,造成美托洛尔溶液的生物毒性在电化学反应过程中先升高后下降.     

废旧锌锰电池生物淋滤-水热法制备纳米锰锌铁氧体

以氧化硫硫杆菌(A.thiooxidans)和氧化亚铁钩端螺旋菌(L.ferrooxidans)为混合淋滤菌株对废旧锌锰电池进行了生物浸提,并以获取的淋滤液为前驱体,采用水热法制备出系列锰锌铁氧体软磁材料(Mn_(1-x)Zn_xFe_2O_4,x=0.2~0.8);结合X射线衍射(XRD)、扫描电镜-能谱(SEMEDX)、振动样品磁强计(VSM)、透射电镜(TEM)、红外光谱(FT-IR)、热重-差热分析(TG-DTA)等表征手段对制备材料的结构、形貌、磁学性能和稳定性进行分析.结果表明,在5%固液比(质量体积比,5 g/100 mL,以下均表述为"5%固液比")下,经过5 d的外源酸调控生物浸提,分别获得了84.5%、63.2%的Zn、Mn浸出效率;当Zn∶Mn∶Fe=0.4∶0.6∶2.0(物质的量比,即x=0.4)时,制备的纳米级Mn_(0.6)Zn_(0.4)Fe_2O_4性能最优,属纯相的立方尖晶石结构,颗粒分布均匀,饱和磁化强度(M_s)、剩余磁化强度(M_r)和矫顽力(H_c)分别为68.9 emu·g~(-1)、4.7 emu·g~(-1)和53.6 Oe,具有热稳定性和耐酸碱性,有望成为一种新型的水处理磁性材料.     

功能化凹凸棒吸附材料的制备及其对重金属废水中Pb2+的吸附行为

重金属离子废水会对人体健康和环境造成严重威胁,吸附法是去除重金属废水中重金属离子的重要方法.对凹凸棒土(ATP)接枝磁性Fe₃O₄纳米粒子,再使用3-氨基丙基三乙氧基硅烷(APTES)进行改性,制备了具有良好吸附性能的凹凸棒复合纳米材料吸附剂(ATP-Fe₃O₄-APTES),并将其用于重金属离子废水的处理.利用FT-IR、 XRD、 SEM及TEM、 BET吸脱附法、 Zeta电位和VSM分析等方法对材料的结构和表面性质进行了分析表征.研究了所制备材料对重金属离子Pb²⁺的吸附行为,考察了溶液pH、吸附时间、吸附温度和Pb²⁺初始浓度等因素对材料吸附性能的影响作用,探讨了吸附过程的吸附动力学、吸附等温线和吸附热力学行为.结果表明,材料对Pb²⁺的最大吸附容量为129.32 mg·g^-1.吸附过程符合准二级动力学模型和Langmuir吸附等温式,表明材料对Pb²⁺的吸附是单分子层化学吸附;吸...     

热喷涂技术与热喷涂材料的发展现状

简述了有关热喷涂的几种喷涂技术,包括等离子喷涂技术、火焰喷涂技术和电弧喷涂技术等的工作原理及发展现状,主要对如何提高涂层结合强度的问题作了说明。对热喷涂涂层材料,尤其是近年来的纳米喷涂材料发展进行了简要介绍。