利用毛细管柱测定水和废水中的苯系物

本文研究了利用毛细管柱分离、测定水样中的苯系物。该方法用二硫化碳萃取水样中的苯系物,细口径毛细管柱分离,ＦＩＤ测定。在分流比为１００∶１的条件下,方法最低检出浓度在００２５～００４７ｍｇ／Ｌ之间,低于填充柱法。该方法适用于地表水、地下水和废水中微量苯系物的测定。     

气相色谱法测定环境标准样品中7种苯系物

氦气作载气,选用DB—WAX毛细管色谱柱,优化柱温、柱流量、进样口温度和检测器温度等色谱参数,实现7种苯系物的快速分析。实验结果表明,通过优化色谱条件,7种苯系物在5.3m in内得到了良好的分离,标准样品的测定均值最大相对误差-1.0%,最大相对标准偏差2.5%。     

便携式质谱联用仪快速定量测定水中7 种苯系物

针对地表水、地下水和饮用水中苯系物的快速定量测定建立方法,该方法适用于水体中苯、甲苯、乙苯、间/对-二甲苯、苯乙烯和邻-二甲苯等苯系物的快速定量结果测定,样品浓度在5~50μg/L的浓度范围内定量检测相对标准偏差低于10%。通过对标准样品测定,其回收率在96.16%~101.50%之间,在快速测定的同时,其定量测定数据具有很高的可靠性。     

大庆地区总悬浮微粒中苯溶物及多环芳烃的测定与评价

通过对大庆地区总悬浮微粒（TSP）中主要化学组成──苯溶物、多环芳烃的测定分析得知：苯溶物占TSP的百分含量，年均值为10．31％，在空气中的平均浓度为12．5μg／m3。与北京燕山地区1983～1984年3个生活区（迎风、东风、东炼）苯溶物年平均值比较，大庆地区苯溶物含量较低。而对总悬浮微粒中多环芳烃的测定结果可明显看出各点采暖期苯并（a）芘、多环芳烃总量的浓度虽都明显高于非采暖期，但其致癌强度和浓度都比北京市、太原市及兰州市弱、低。     

地下水中苯系物污染修复研究进展

苯系物(苯、甲苯、乙苯和二甲苯,BTEX)是重要的环境污染物之一。BTEX高溶解,高挥发,高毒性的特点使其成为地下水污染关注的特点。强调了地下水中苯系物的来源及相关性质,总结了治理苯系物的历史应用技术,介绍了新兴修复技术并展望了未来的发展方向,为地下水中苯系物的处理提供借鉴。     

用顶空-气相色谱质谱法测定固体废物中苯系物的分析方法

本方法采用静态顶空进样技术对固体废物样品进行处理,利用气相色谱质谱联用对固体废物中苯系物(9种)进行了测定分析,通过测定得到最低检出浓度为0.38~1.02μg/kg;加标回收率为76.6%~124.4%;RSD为2.2%~18.2%。本实验分析时间短,操作简单,灵敏及测定结果较为满意。     

现代分离技术在环境分析中的应用

对样品进行预处理分离的主要目的是:①浓缩痕量污染物,降低最小检测浓度;②除去干扰物,提高测定的精确度和灵敏度;③通过化学衍生,提高被测物的灵敏度和选择性;④消除对分析系统有害的物质,使仪器保持良好稳定的运行状况。文章综合论述了固相萃取技术、固相微萃取技术、膜萃取技术、超临界流体萃取技术、毛细管电泳技术、加速溶剂萃取技术和微波萃取技术等现代分离技术在大庆油田环境分析中的应用现状以及分离技术的发展前景。     

磁分离技术在我国废水处理中的研究进展

本文介绍了磁分离技术的基本原理、分离方法和设备，综述了该技术在某些特定废水处理中的应用现状。磁分离技术的实际应用具有分离效率高、分离速度快、选择性好、处理对象广、成本低廉、分离物系的粒度可达到很小，并且不受处理体系的温度、密度、酸碱度限制等优点，可以使某些采用传统分离方法较难或不能分离的物系得以顺利地分离，有较为广泛的应用前景。     

色谱法测定水中苯乙烯的实验室应用

文章通过"溶剂萃取-毛细管柱气相色谱法测定水中苯乙烯"方法的实验室应用,进行了曲线制作、验证、标准样品的实际测定,允许相对偏差、相对误差及加标回收率均符合方法要求,验证了气相色谱法测定苯系物(程序升温和分流进样),具有较高的精密度和准确度。同时证明了在此实验条件下采用"溶剂萃取-毛细管柱气相色谱法测定水中苯乙烯"的方法可行。     

东道海子湖水中苯系物的分析研究

本文以新疆古尔班通古特沙漠腹地的东道海子湖水为对象,研究东道海子湖水中苯系物的污染特征,并对湖水中苯系物的潜在生态危害进行分析评价。结果表明:东道海子湖水中苯系物的含量均满足我国水环境质量一级标准,苯的浓度仍然小于我国生活饮用水卫生标准中规定的0.01 mg/L,但经过健康风险评价,发现其仍会对人体产生一定的致癌风险。苯、甲苯、乙苯、邻二甲苯、间二甲苯、对二甲苯的非化学致癌物风险(HQ)值远低于1,表明各类苯系物均无非致癌物的化学风险。     

The Atmosphere can be a Source of Certain Water Soluble Volatile Organic Compounds in Urban Streams

Surface water and air volatile organic compound (VOC) data from 10 U.S. Geological Survey monitoring sites were used to evaluate the potential for direct transport of VOCs from the atmosphere to urban streams. Analytical results of 87 VOC compounds were screened by evaluating the occurrence and detection levels in both water and air, and equilibrium concentrations in water (C_w^s) based on the measured air concentrations. Four compounds (acetone, methyl tertiary butyl ether, toluene, and m‐ & p‐xylene) were detected in more than 20% of water samples, in more than 10% of air samples, and more than 10% of detections in air were greater than long‐term method detection levels (LTMDL) in water. Benzene was detected in more than 20% of water samples and in more than 10% of air samples. Two percent of benzene detections in air were greater than one‐half the LTMDL in water. Six compounds (chloroform, p‐isopropyltoluene, methylene chloride, perchloroethene, 1,1,1‐trichloroethane, and trichloroethene) were detected in more than 20% of water samples and in more than 10% of air samples. Five VOCs, toluene, m‐ & p‐xylene, methyl tert‐butyl ether (MTBE), acetone, and benzene were identified as having sufficiently high concentrations in the atmosphere to be a source to urban streams. MTBE, acetone, and benzene exhibited behavior that was consistent with equilibrium concentrations in the atmosphere.     

我国大气环境管理历程与展望

随着大气环境问题从煤烟型向以PM_2.5和O₃为特征的区域复合型污染演变，我国大气污染控制模式从以污染物排放浓度控制为核心、以污染物排放总量控制为核心逐渐走向以大气环境质量改善为核心。特别是近几年，全国各地在空气质量管理、科学精准治污等领域开展一系列积极的探索与实践，取得了显著成效。本文系统回顾了近50年来我国不同阶段大气环境管理工作的特点，重点梳理了2013年《大气污染防治行动计划》实施以来，空气质量管理经验与成绩，结合减污降碳总体部署对我国2035年“美丽中国建设目标基本实现”时的空气质量进行了展望，从PM_2.5与O₃协同控制的角度出发，提出了“十四五”期间我国大气环境管理的总体思路。     

Policy evaluation of vehicle exhaust standards in Japan from 1995 to 2005 based on two human health risk indices for air pollution and global warming

Measures for vehicle exhaust emissions aimed at reducing either air pollution or global warming could have counterproductive effects on one another. Increasing diesel passenger vehicles, which generally have lower CO₂ emissions than gasoline counterparts, leads to increasing particulate matter (PM) emissions, while gasoline has lower PM emissions than diesel. It is said that stringent limits on PM emission factors discourages improved CO₂ emission factors. Without including both effects in a risk evaluation, one cannot evaluate whether the total risk is reduced or not. Hence, we evaluated representative exhaust emission measures based on risk evaluation for both air pollution and global warming. Considering consumer choice between diesel and gasoline passenger vehicles and emissions standards adopted in Japan from 1995 to 2005, we built five cases for vehicle policy evaluation. For each case, we estimated disability-adjusted life years (DALY) as an index of human health risk caused by lung cancer linked to inhalation exposure of elemental carbon in PM as well as due to global warming linked to CO₂. The results of our risk evaluation reveal that the case adopting the 2005 new long-term Japanese emission standard reduces the human health risk caused by lung cancer due to air pollution by 0.6 × 10³ DALY, but would increase the risk due to global warming by 31.9 × 10³ DALY compared with the case of adopting EURO 4, for the same conditions of passenger vehicle choice from 1995. These results suggest that the characteristics of Japanese emissions standards are mainly designed to reduce air pollution.     

迪那2气田液化气无水冷却工艺研究

迪那2气田液化气生产设计采用空冷加水冷工艺,存在能耗大和水冷器易腐蚀结垢等安全隐患。利用HYSYS软件对迪那2气田轻烃回收工艺进行分析,并增设液化气后冷器,利用脱乙烷塔气相对液化气进行冷却,通过醇烃液分离压力、后冷器及空冷器冷却能力等参数的模拟计算和优化,将醇烃液三相分离器压力由常规的2.5MPa提高至5MPa,取消醇烃液导热油加热和液化气水冷,降低了装置能耗,年节水1.44×104m3,节电1.45×105 kW.h,杜绝了水冷器腐蚀穿孔的安全隐患,最终提出了醇烃液高压分离+空冷器+后冷器的液化气无水冷却工艺。     

乌鲁木齐黑碳气溶胶浓度时间变化特征及影响因素分析

利用乌鲁木齐市环境空气超级站中MAAP-5012型黑碳仪对乌鲁木齐市黑碳气溶胶进行连续一年的监测,并结合乌鲁木齐环境空气质量城市站小时数据和日数据及气象数据对黑碳气溶胶变化情况进行综合分析.结果 表明:2019年6月至2020年5月乌鲁木齐黑碳气溶胶浓度日均值为1 506(±1 096) ng/m3,本底值为575 n...     

高效液相色谱法测定环境空气酰胺类化合物

高效液相色谱法测定环境空气中酰胺类化合物,采用多孔玻板吸收管采集环境空气中的酰胺类化合物,吸收液经0.22μm膜过滤后,经C18色谱柱分离,采用紫外检测器检测。丙烯酰胺、二甲基甲酰胺、二甲基乙酰胺的检出限分别为0.04μg/m3、0.000 2 mg/m3、0.000 2mg/m3（10 ml吸收液,采集15 L环境空气样品计）。高、中、低三种浓度三种酰胺类化合物的回收率区间为70.8%~90.2%,相对标准偏差范围小于9.6%。该方法操作简单,结果准确、可靠,适用于环境空气中酰胺类化合物的快速、准确监测。     

The convective hot air drying of Lactuca sativa slices

The storage of fresh agricultural products is not easy because of its high moisture. Dehydration is an efficient preservation method. The investigation of drying modeling and transfer characteristics are important for selecting operating conditions and equipment design. The drying behavior of Lactuca sativa slices, with the thickness of 2 mm, was investigated at 60.0–80.0°C and 0.60–1.04 m sec^?1 velocity in a convective hot air drier. The mass transfer during the drying process was described using six thin drying models. The convective heat transfer coefficient α and mass transfer coefficient k_H were finally calculated. The results showed that the drying process could be separated into three stages including accelerating rate, constant rate, and falling rate period, which was influenced by hot air temperature and velocity, and the Modi?ed Page model agreed well with the experimental data. When the operating temperature was increased from 60.0°C to 80.0°C, α was found increased from 88.07 to 107.93 W·m^?2·K^?1, and k_H increased from 46.32 × 10^–3 to 68.04 × 10^–3 kg·m^?2·sec^?1·ΔH^?1. With the increase of air velocity from 0.60 to 1.04 m·sec^?1, α was increased from 78.85 to 101.35 W·m^?2·K^?1, and k_H was enhanced from 51.78 × 10^–3 to 65.85 × 10^–3 kg·m^?2·sec^?1·ΔH^?1.     

WATER QUALITY MODEL OUTPUT UNCERTAINTY AS AFFECTED BY SPATIAL RESOLUTION OF INPUT DATA1

ABSTRACT: Resolution of the input GIS data used to parameterize distributed‐parameter hydrologic/water quality models may affect uncertainty in model outputs and impact the subsequent application of model results in watershed management. In this study we evaluated the impact of varying spatial resolutions of DEM, land use, and soil data (30 × 30 m, 100 × 100 m, 150 × 150 m, 200 × 200 m, 300 × 300 m, 500 × 500 m, and 1,000 × 1,000 m) on the uncertainty of SWAT predicted flow, sediment, NO₃‐N, and TP transport. Inputs included measured hydrologic, meteorological, and watershed characteristics as well as water quality data from the Moores Creek watershed in Washington County, Arkansas. The SWAT model output was most affected by input DEM data resolution. A coarser DEM data resolution resulted in decreased representation of watershed area and slope and increased slope length. Distribution of pasture, forest, and urban areas within the watershed was significantly affected at coarser resolution of land use and resulted in significant uncertainty in predicted sediment, NO₃‐N, and TP output. Soils data resolution had no significant effect on flow and NO₃‐N predictions; however, sediment was overpredicted by 26 percent, and TP was underpredicted by 26 percent at 1,000 m resolution. This may be due to change in relative distribution of various hydrologic soils groups (HSGs) in the watershed. Minimum resolution for input GIS data to achieve less than 10 percent model output error depended upon the output variable of interest. For flow, sediment, NO₃‐N, and TP predictions, minimum DEM data resolution should range from 30 to 300 m, whereas minimum land use and soils data resolution should range from 300 to 500 m.     

Potential Environmental Benefits from Increased Use of Bioenergy in China

Because of its large population and rapidly growing economy, China is confronting a serious energy shortage and daunting environmental problems. An increased use of fuels derived from biomass could relieve some demand for nonrenewable sources of energy while providing environmental benefits in terms of cleaner air and reduced emissions of greenhouse gases. In 2003, China generated about 25.9 × 10⁸ metric tons of industrial waste (liquid + solid), 14.7 × 10⁸ metric tons/year (t/y) of manure (livestock + human), 7.1 × 10⁸ t/y of crop residues and food-processing byproducts, 2 × 10⁸ t/y of fuelwood and wood manufacturing residues, and 1.5 × 10⁸ t/y of municipal waste. Biofuels derived from these materials could potentially displace the use of about 4.12 × 10⁸ t/y of coal and 3.75 × 10⁶ t/y of petroleum. An increased bioenergy use of this magnitude would help to reduce the emissions of key air pollutants: SO₂ by 11.6 × 10⁶ t/y, NO_X by 1.48 × 10⁶ t/y, CO₂ by 1.07 × 10⁹ t/y, and CH₄ by 50 × 10⁶ t/y. The reduced SO₂ emissions would be equivalent to 54% of the national emissions in 2003, whereas those for CO₂ are 30%. It is important to recognize, however, that large increases in the use of biomass fuels also could result in socioeconomic and environmental problems such as less production of food and damage caused to natural habitats.