臭氧耦合ASBR/SBR控氮磷污泥减量化水处理工艺

针对传统污泥减量化工艺中氮磷难以达标的问题,以ASBR/SBR组合工艺为基础辅助臭氧氧化预处理,提出了臭氧耦合ASBR(anaerobic sequencing batch reactor)/SBR(sequencing batch reactor)工艺实现污泥减量与氮磷协同控制,系统评价了该工艺对污泥减量和脱氮除磷效果。结果表明,未投加臭氧时,SBR的污泥表观产率系数Yobs(即降解每克COD产生的悬浮固体的量)均值为0.228 g·g~(-1),投加臭氧(投量为0.074 g·g~(-1))后Yobs均值降低至0.132 g·g~(-1),降低了42%;臭氧投加前后出水COD、NH+4-N、TN和PO3-4-P去除率变化不大,分别在91%、95.2%、74.7%和49.4%左右;投加臭氧使得SOUR(specific oxygen uptake rate)(即每小时每克污泥所需氧气量)由2.8 mg·(g·h)~(-1)降低至2.4 mg·(g·h)~(-1),表明臭氧氧化并未明显抑制生物活性;此外,投加臭氧使得MLVSS/MLSS由0.85降低至0.83,表明实验过程中未发现惰性物质的累积。实验结果表明,臭氧耦合ASBR/SBR工艺在实现污泥减量和控制氮磷方面具有一定的工程应用价值。     

原位臭氧氧化污泥减量工艺的运行效能

采用ASBR/SBR原位臭氧污泥减量工艺,重点研究了原位臭氧氧化对SBR段污泥产率和出水水质的影响。两个相同的ASBR/SBR组合工艺同时运行,每隔3个周期向臭氧投加组SBR的曝气阶段原位间歇投加臭氧,臭氧投加量为0.027 g O3/g MLSS,连续运行40 d;对照组不投加臭氧作为对比。结果表明,原位臭氧氧化实现污泥减量约43.9%,臭氧投加组SBR段平均污泥产率系数为0.1447 g SS/g SCOD,而对照组为0.2580 g SS/g SCOD,投加组没有惰性污泥的累积,并且污泥沉淀性能得到改善。原位臭氧氧化对出水水质影响不大,投加组与对照组相比,臭氧投加3周期后的出水COD、NH4+-N、TN和TP平均值分别为47.8、0.76、14.1和6.4 mg/L,去除率分别下降了4%、2%、3%和7.7%,其中COD、NH4+-N和TN均能达到《城镇污水处理厂污染物排放标准》(GB18918-2002)一级A标准。     

原位臭氧氧化对活性污泥系统硝化和反硝化作用的影响研究

将厌氧序批式间歇反应器(ASBR)和序批式间歇反应器(SBR)串联组成污泥减量新工艺,着重探讨了对SBR段进行原位臭氧投加时,臭氧氧化作用对系统硝化和反硝化能力的影响,并以不投加作为对照。结果表明,将臭氧原位投加到ASBR—SBR组合工艺的SBR段,臭氧投加量为0.027g(以每克MLSS计),每隔3个周期再次投加、连续运行40d,试验组SBR段臭氧投加当期出水COD去除率为86%,比对照组下降了9百分点,但臭氧氧化细胞内大量有机物进入混合液中,为反硝化作用提供了外加碳源,对污泥反硝化能力的提高起到了一定的促进作用;试验组部分硝化细菌由于臭氧的强氧化作用而失去活性,但是随着剩余污泥量的减少,系统的污泥龄延长,有利于硝化细菌的生长,使得系统的硝化能力基本未受影响;试验组臭氧投加当期SBR段出水NO2--N平均浓度比对照组的高18.9%,但经过3个周期的运行后,其SBR段出水NO2--N平均质量浓度降低至7.57mg/L,基本与对照组持平;试验组臭氧投加当期SBR段出水NO3--N的平均浓度高于对照组,但经过3个周期的运行后,试验组出水NO3--N平均浓度低于对照组;试验组臭氧投加当期SBR段出水TN和对照组的出水TN平均去除率分别为65%和75%,但试验组再经过3个周期的运行后,出水TN平均去除率可以达到72%。可见,原位投加臭氧并未对SBR段的硝化和反硝化能力产生明显的影响。     

畜禽养殖废水生物处理剩余污泥臭氧减量过程中的重金属释放简

采用臭氧氧化污泥减量法对畜禽养殖废水SBR中的剩余污泥进行处理。当臭氧反应时间控制在30 min时,污泥的溶解比例在30%左右（以 MLSS计）。上清液中一定量的SCOD溶出可为生物处理单元提供充足的碳源,同时在上清液中,TN、TP及水相重金属浓度增加有限,臭氧氧化后的污泥液回流污水处理系统后造成的N、P处理负荷较小,重金属对污泥微生物的活性抑制风险较低。若继续延长臭氧的反应时间,上清液SCOD、TN、TP以及重金属Cu、Pb的释放速率明显增加,同时上清液的C/N降低,臭氧化后的污泥液回流反而不利于生物单元的脱氮处理。综合考虑TN、TP及水相重金属浓度增加的危害性,臭氧反应时间应控制在30 min,臭氧实际投加量应为123.1 mg O₃/g SS。     

畜禽养殖废水生物处理剩余污泥臭氧减量过程中的重金属释放

采用臭氧氧化污泥减量法对畜禽养殖废水SBR中的剩余污泥进行处理。当臭氧反应时间控制在30min时,污泥的溶解比例在30％左右（以MLSS计）。上清液中一定量的SCOD溶出可为生物处理单元提供充足的碳源,同时在上清液中,TN、TP及水相重金属浓度增加有限,臭氧氧化后的污泥液回流污水处理系统后造成的N、P处理负荷较小,重金属对污泥微生物的活性抑制风险较低。若继续延长臭氧的反应时间,上清液SCOD、TN、TP以及重金属cu、Pb的释放速率明显增加,同时上清液的C／N降低,臭氧化后的污泥液回流反而不利于生物单元的脱氮处理。综合考虑TN、TP及水相重金属浓度增加的危害性,臭氧反应时间应控制在30min,臭氧实际投加量应为123．1mg O3／gSS。     

直接投加ClO_2对SBR污泥减量及污染物去除的影响

直接向采用交替停曝气模式运行的序批式反应器(SBR)中投加ClO_2,考察了在处理模拟生活污水时不同ClO_2投加剂量对SBR污泥减量及污染物去除的影响。结果表明,ClO_2最佳投加剂量为2.0 mg ClO_2/g干污泥,此时,与对照反应器(未投加ClO_2)相比,SBR污泥减量效率为28.0%,系统污泥产率系数为0.08 g MLVSS/g COD。溶胞-隐性生长、解偶联代谢和内源代谢对污泥减量均有贡献。在ClO_2最佳投加剂量下,SBR出水COD、NH3-N、TN和TP浓度分别增加了(28.80±1.53)、(3.49±1.79)、(2.30±0.02)、(0.21±0.05)mg/L,但出水水质仍满足《城镇污水处理厂污染物排放标准》(GB18918-2002)一级B标准。     

臭氧预处理对剩余污泥特性及厌氧消化的影响

研究了臭氧预处理对剩余污泥特性及厌氧消化的影响,考察了臭氧投加量对污泥特性的影响,并进行了预处理后污泥厌氧消化产气的实验。结果表明,当臭氧处理时间为15 min时,污泥上清液中SCOD含量达到最高为1 006.08 mg·L~(-1),较未处理污泥提高了420.85%。污泥上清液中蛋白质和多糖含量在臭氧处理时间为10 min时达到最高。氨氮的含量在15 min时达到最大值。三维荧光结果显示随着臭氧投加量的增加污泥中的富里酸类物质有不同程度的减少,在臭氧处理时间为20 min时富里酸类物质减少量最为明显。显微镜和扫描电镜结果显示随着臭氧投加量的增加污泥中的微生物细胞结构受到了不同程度破坏。厌氧消化结果显示当臭氧处理时间为10 min时,污泥产甲烷率达到最高为318.39 m L·(g·VS)-1,较空白对照组提高了396.00%。     

全细胞脂肪酶(菌)对SBR系统中活性污泥性能的影响

将全细胞脂肪酶(菌)以产脂肪酶微生物的形式直接投加到SBR内,与投加野生型酵母菌及空白对照进行比较,研究其对活性污泥性能及含油脂废水处理效果的影响。结果表明,在15～20℃,pH 6.5～7.5,进水油脂浓度2 000 mg/L的条件下,投加一定量全细胞脂肪酶(菌)的SBR系统间歇处理4 d,活性污泥增殖速度加快,是投加野生型酵母菌的1.3倍。静置30 min时活性污泥SV达到45%,SVI为151,MLSS最高可达2 965 mg/L左右,絮凝时间缩短且无污泥膨胀现象。投加全细胞脂肪酶(菌)的SBR系统中,油脂去除率为86.5%,COD去除率为79.5%,与投加野生型酵母菌的SBR系统相比去除率提高了1.3倍。说明投加全细胞脂肪酶(菌)后活性污泥性能增强,油脂废水处理效率提高。     

污泥活性炭强化SBR法处理垃圾渗滤液的实验研究

为了进一步处理垃圾渗滤液,试验采用污泥活性炭强化序批式间歇反应器（SBR）法进行处理,通过对比普通SBR法试验,得出投加污泥活性炭强化SBR法处理垃圾渗滤液的效果要远远高于普通SBR法。当污泥活性炭的投加量为1.2 g/L,容积负荷为0.5～1.5 kg BOD₅/(m³·d)时,进水1 h,曝气10 h,沉淀1.5 h,闲置1.5 h,处理效果最好,COD的去除率达到了85%,NH³-N的去除率达到了90%。     

臭氧预处理—厌氧消化工艺促进剩余污泥减量化的研究

主要研究了臭氧氧化对剩余污泥的破解效果及污泥厌氧消化效率的影响.结果表明,随着臭氧投加量的增加,悬浮物(SS)、可挥发性悬浮物(VSS)逐步减少,而剩余污泥上清液中的溶解性COD(SCOD)、总有机碳(TOC)、蛋白质和多糖则明显增加.经臭氧预处理(臭氧投加量为0.050 g(以每克SS计))后,剩余污泥中温(35℃)厌氧消化效率明显提高,经65d稳定运行后,总挥发性固体(TVS)去除率为67.58％,与未经臭氧预处理的剩余污泥相比提高50.61％;甲烷平均产率为0.303 L(以每克TVS计),与未经臭氧预处理的剩余污泥相比提高54.59％.可见,臭氧预处理能有效促进污泥厌氧消化,从而达到污泥减量的目的.     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

The variation of street air levels of PAH and other mutagenic PAC in relation to regulations of traffic emissions and the impact of atmospheric processes

The occurrence of particle associated PAH and other mutagenic PAC was determined in 1996 in the street air of Copenhagen. In addition, particle extracts were tested for mutagenicity. The measurements were compared with previous measurements in 1992/1993. The levels had decreased in this period. The decrease was caused by an implementation of light diesel fuels for buses and the exchange of older petrol-driven passenger cars with catalystequipped new ones. About 65% of the reduction was caused by the application of the light diesel fuels. Under special conditions, chemical processes in the atmosphere produced many more mutagens than the direct emissions. The concentrations of S-PAC and N-PAC were 10 times lower than those of PAH, while the levels of oxy-PAH were in the same order of magnitude as those of PAH. Benzanthrone, an oxy-PAH, is proposed to be formed in the atmosphere in addition to direct emissions. Benzo(a)pyrene, often applied as an air quality criteria indicator, was photochemically degraded in the atmosphere. A strong increase in the mutagenic activities was observed to coincide with a depletion of benzo(a)pyrene.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Teratological effects of pesticides in vertebrates: a review

Abstract

In the last decades, the use and misuse of pesticides in the agriculture have increased, having a severe impact on ecosystems and their fauna. Although the various effects of pesticides on biodiversity have been already documented in several studies, to our knowledge no consistent overview of the impact of pesticides in vertebrates, both terrestrial and aquatic, is available. In this review, we try to present a concise compilation of the teratogenic effects of pesticides on the different classes of vertebrates – mammals, birds, reptiles, amphibians and fish.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.