Dissipation and mobility of permethrin in the field with repeated applications under tropical conditions

Studies on persistence, mobility and the effect of repeated application of permethrin on its half-life were carried out under field conditions. The half-life of permethrin in the top 20 cm of the soil increased from 11.5 to 23.6 days as the application rates increased from 35 to 140 g ha(-1). Induced by heavier rainfall, more residues moved downward in trial 2 than in trial 1. Repeated applications enhanced degradation rates and mobility of permethrin in the soil. The residue level in the 0-5-cm layer was reduced at day 28 after 17 consecutive applications to a level lower than after 5 applications. The half-life of permethrin was reduced from 15.9 days to 11.2 days after 5 and 17 applications, respectively. The residue reached the 15-20 cm layer much earlier (approximately 3 days after treatment) in soil that received 17 applications as compared to those with two applications.     

Fate of permethrin in model outdoor ponds

Abstract

In 1979 and 1980, outdoor artificial ponds were treated with ¹⁴C‐pennethrin (labelled at either the cyclopropyl or methylene position) at 0.028 kg/ha (15 ug/L). Uptake of permethrin by duckweed and hydrosoil was monitored by direct combustion, TLC‐autoradiography, HPLC, and liquid scintillation counting. Rapid loss of permethrin from the waiter coincided with the detection of five degradation products in the water at concentrations below 2.0 ug/L. The products were cis‐ and trans‐cyclopropyl acid, phenoxybenzoic acid, and phenoxybenzyl alcohol, and an unknown non‐cleaved product of permethrin. Permethrin was readily sorbed by duckweed but was not persistent. Permethrin residues in the hydrosoil, which was the major sink for permethrin added to the ponds, were persistent and were detected at 420 days post‐treatment. Cis‐permethrin was more persistent in the hydrosoil than the trans‐permethrin. The results indicated that permethrin in water was short‐lived at an application rate of 15 ug/L because of the rapid degradation of permethrin in the water and sorption of permethrin by the hydrosoil and vegetation. However, at one year post‐treatment, permethrin residues were still detected in the hydrosoil at 1.0 ug/kg.     

Determination of disulfoton and permethrin residues in an organic soil and their translocation into lettuce, onion and carrot.

The residues of disulfoton and permethrin in an organic soil and in vegetables grown in soil treated with a granular formulation of the pesticides were determined by gas chromatography. The residues were removed from soil or plant samples by successive extractions with acetone and hexane. Permethrin persisted in the soil for the initial 28 days and declined slowly during the rest of the season but disulfoton after persisting for one week at the applied concentration was degraded in the next two weeks. The insecticides did not translocate into the edible parts of the vegetables but were present in the root system of onion and lettuce. Carrot and lettuce yields were not singificantly different from those of the controls but onion yields were substantially decreased by the use of permethrin.     

Residues of dicofol on cucumber grown under plastic covers in Jordan

Residues of dicofol were determined on cucumber leaves and fruits under plastic house (PH) and plastic tunnels (PT). Five sprays, 8 d apart, were applied at 0.15% concentration. Initial deposits on leaves were 48 and 58 ppm under PH and PT, respectively. In the last sampling date of leaves, the amounts of 191 and 135 ppm were detected under both cultures, respectively. There was a continuous increase in the initial residue after each spray. The highest amount of dicofol (401) was determined 1 d after the fifth spray under PH. The exposure to high residues may pose a risk to fieldworkers. On cucumber fruits, residues of 0.95 and 1.60 ppm were determined 1 d after the fourth spray under PH and PT, respectively. These residues decreased after 4 d to 0.40 and 1.49 ppm, respectively. Almost no detectable residues could be determined 8 d after sprays number 4 and 5 under both cultures. All dicofol residues on the fruits were below the tolerance level of 2 ppm.     

Residues of dicofol on cucumber grown under plastic covers in jordan

Abstract

Residues of dicofol were determined on cucumber leaves and fruits under plastic house (PH) and plastic tunnels (PT). Five sprays, 8 d apart, were applied at 0.15% concentration. initial deposits on leaves were 48 and 58 ppm under PH and PT, respectively. In the last sampling date of leaves, the amounts of 191 and 135 ppm were detected under both cultures, respectively. There was a continuous increase in the initial residue after each spray. The highest amount of dicofol (401) was determined 1 d after the fifth spray under PH. The exposure to high residues may pose a risk to fieldworkers.

On cucumber fruits, residues of 0.95 and 1.60 ppm were determined 1 d after the fourth spray under PH and PT, respectively. These residues decreased after 4 d to 0.40 and 1.49 ppm, respectively. Almost no detectable residues could be determined 8 d after sprays number 4 and 5 under both cultures. All dicofol residues on the fruits were below the tolerance level of 2 ppm.     

Phosmet residues in an orchard and adjacent recreational area

Two cover sprays of phosmet were applied to an orchard adjoining a camping area and a bird sanctuary with a resident goose population. Insecticide residues were monitored on orchard leaves, orchard ground cover, ground cover in the camp-site and along the adjacent lakeshore. Despite attempts to minimize drift, significant spray residues were found outside the target area. Residues on ground cover and leaves were reduced by sprinkler irrigation subsequent to spray application.     

Studies on the residues of phosalone on chilli by GLC after multiband plate cleanup

Abstract

Four sprays of 0.05 ana 0.10% phosalone were given on chilli (Capsicum annuum Linn.) crop at an interval of 15 days starting from 21 days after transplanting. Residues were determined in the green chilli fruits by GLC after cleanup of extract on multiband thin‐layer plate. The half‐lives of residues were 1.55 and 1.68 days on chilli fruits from the crop treated with four sprays of 0.05 and 0.10% phosalone respectively. The time required to reach the tolerance limit of 1 ppm after last spray with 0.05 and 0.10 % emulsion was 4.75 and 7.62 days respectively. Washing of fruits under tap water was found effective in bringing down the level of phosalone residues by 21.64 to 75.11 %.     

Phosmet residues in an orchard and adjacent recreational area 1

Abstract

Two cover sprays of phosmet were applied to an orchard adjoining a camping area and a bird sanctuary with a resident goose population. Insecticide residues were monitored on orchard leaves, orchard ground cover, ground cover in the camp‐site and along the adjacent lakeshore. Despite attempts to minimize drift, significant spray residues were found outside the target area. Residues on ground cover and leaves were reduced by sprinkler irrigation subsequent to spray application.     

Organochlorine residues in roof timbers and possible implications for bats

In Britain, many species of bat regularly use buildings as roosts. DDT, DDE, dieldrin (HEOD) and gamma-HCH (lindane) have been detected in carcasses of bats that had died a short while before they were found. Roof timbers may be a source of this contamination. This study reports concentrations of organochlorines in (i) roof timbers known to have been treated in the past (spot samples; n - 17) and (ii) timbers before and after treatment with commercial permethrin formulations (pre-treatment and post-treatment samples, n = 11). Gamma-HCH was detected in 13 spot samples and HEOD in 6. Where present, mean (+/-1 SE) concentrations in wood were 15.6+/-6.5 microg g-1 WW (n = 13) and 25.0+/-11.8 microg g-1 WW (n = 6), respectively. DDT was not detected in any spot samples, but permethrin was detected in four (1264+/-567 microg g(-1) WW) samples, but not in the corresponding pre-treatment samples; in one other pair of samples, concentrations of gamma-HCH increased from 74 to 2468 microg g-1 WW after treatment. Both DDT and HEOD occurred in low (<2 microg g-1 WW) concentrations in five post-treatment samples and in one and zero pre-treatment samples, respectively; the highest dieldrin concentration measured was 30.9 microg g-1 WW. Permethrin was not detectable in any pre-treatment samples but was present in ten post-treatment samples in concentrations ranging from 93 to 2995 microg g-1 WW. The spot results suggest that low concentrations of organochlorines can persist in treated roof timbers for at least 13 years post-treatment. Occasionally, these pesticide residues in timber may be of sufficient magnitude to result in bats absorbing a substantial proportion of a lethal dose. Results also suggest that there is organochlorine contamination of permethrin formulations and that the solvents used in new applications of pesticide may re-mobilise organochlorines already present in wood.     

Comparison of real-time instruments used to monitor airborne particulate matter

Measurements collected using five real-time continuous airborne particle monitors were compared to measurements made using reference filter-based samplers at Bakersfield, CA, between December 2, 1998, and January 31, 1999. The purpose of this analysis was to evaluate the suitability of each instrument for use in a real-time continuous monitoring network designed to measure the mass of airborne particles with an aerodynamic diam less than 2.5 microns (PM2.5) under wintertime conditions in the southern San Joaquin Valley. Measurements of airborne particulate mass made with a beta attenuation monitor (BAM), an integrating nephelometer, and a continuous aerosol mass monitor (CAMM) were found to correlate well with reference measurements made with a filter-based sampler. A Dusttrak aerosol sampler overestimated airborne particle concentrations by a factor of approximately 3 throughout the study. Measurements of airborne particulate matter made with a tapered element oscillating microbalance (TEOM) were found to be lower than the reference filter-based measurements by an amount approximately equal to the concentration of NH4NO3 observed to be present in the airborne particles. The performance of the Dusttrak sampler and the integrating nephelometer was affected by the size distribution of airborne particulate matter. The performance of the BAM, the integrating nephelometer, the CAMM, the Dusttrak sampler, and the TEOM was not strongly affected by temperature, relative humidity, wind speed, or wind direction within the range of conditions encountered in the current study. Based on instrument performance, the BAM, the integrating nephelometer, and the CAMM appear to be suitable candidates for deployment in a real-time continuous PM2.5 monitoring network in central California for the range of winter conditions and aerosol composition encountered during the study.     

Degradation of disulfoton,oxydemeton‐methyl,methamidophos and demeton in asparagus plant

Abstract

Disulfoton and methamidophos (both at 1.12 kg a.i./ha), oxydemeton‐methyl and demeton, (both at 0.56 kg a.i./ha) were applied as post‐harvest foliar sprays to control the European asparagus aphid, Brachycolus asparagi. Oxidation of disulfoton, oxydemeton‐methyl and demeton to their corresponding sulfoxides and sulfones occurred in asparagus foliage 2 to 5 days after application. The total residues of these three compounds, including their toxic oxidative metabolites declined to less than 0.5 ppm about 47 days after the spray application whereas methamidophos persisted longer; 0.84 ppm of its residue was found even after 85 days. No residue was found above the limit of detection of 0.002 ppm in any asparagus spears which were produced in the following spring; the four compounds were sprayed on the asparagus plants during the previous season at realistic rates for aphid control.     

Determination of disulfoton and permethrin residues in an organic soil and their translocation into lettuce,onion and carrot 1

Abstract

The residues of disulfoton and permethrin in an organic soil and in vegetables grown in soil treated with a granular formulation of the pesticides were determined by gas chromatography. The residues were removed from soil or plant samples by successive extractions with acetone and hexane. Permethrin persisted in the soil for the initial 28 days and declined slowly during the rest of the season but disulfoton after persisting for one week at the applied concentration was degraded in the next two weeks. The insecticides did not translocate into the edible parts of the vegetables but were present in the root system of onion and lettuce. Carrot and lettuce yields were not significantly different from those of the controls but onion yields were substantially decreased by the use of per‐methrin.     

Optimization of a methodology for the simultaneous determination of deltamethrin,permethrin and malathion in stored wheat samples using dispersive liquid–liquid microextraction with solidification of floating organic drop and HPLC-UV

The purpose of this study was to investigate common pesticides in stored wheat at Kermanshah province's silos in Iran. A simple, inexpensive, reliable and environmentally friendly method based on dispersive liquid–liquid microextraction with solidification of floating organic drop was developed. The analytical characteristics of the method were determined. Also, various parameters such as the materials of the silos, types of ownerships of the silos, geographic orientation of silo locations and climatic conditions of silo locations on pesticide residues in studied wheat samples were investigated. Among all the studied parameters, the climatic conditions of silo locations showed the highest influence on pesticide residues in wheat samples. Generally, 61.2% of the samples had pesticide levels below the method detection limits and 38.8% of the total samples had at least one of the understudied pesticides. Also, 13.9% of the samples had deltamethrin residues, 16.7% of the samples had permethrin, 22.2% of the samples had malathion, 11.1% of the samples had both permethrin and malathion and 2.8% of the samples had both deltamethrin and malathion. The results revealed that the residues of deltamethrin and malathion were lower than the standard level announced by European Union regulation and only three samples contained permethrin higher than Europe standard level.     

Disappearance of dimethoate,methamidophos and pirimicarb in lettuce

Abstract

Foliar sprays of dimethoate at 150 or 300 g a.i./ha, methamidophos at 450 or 900 g a.i./ha and pirimicarb at 140 or 280 g a.i./ha were applied for control of the green peach aphid, Myzus pericae (Sulzer), and the lettuce aphid, Nasonovia ribisnigri (Mosley), about 2 weeks before the lettuce started heading, and again about 1 week from harvest. In lettuce, dimethoate partially oxidized to its oxon and pirimicarb converted to its methylamino‐ and/or formyl methylamino‐analogues. Most residues were present in the outer leaves which were exposed directly to the sprays; only traces of residues were detected in samples of the inner head leaves. Total residues disappeared rapidly. Pirimicarb was the least persistent and only traces of residues (<0.01 ppm) were detected in marketable heads. Concentrations of dimethoate, including the oxon and of methamidophos were well below their respective tolerances of 2 and 1 ppra respectively.     

Control of blueberry thrips,frankliniella vaccinii morgan,with permethrin and effect on yield and residue in fruit

Abstract

Permethrin at 0.4 kg a.i./ha controlled blueberry thrips Frankliniella vaccinii Morgan. There was no plant damage and crop yield was notably increased. Permethrin was extracted from berries with acetone, partitioned in hexane, cleaned‐up on Florisil column and analysed by the electron capture gas chromatography using a 3% OV‐210 column. No permethrin residues were found in the berries. The relative retention times of cis‐, and trans‐permethrins to aldrin were 10.3 and 12.1, respectively. The absence of permethrin from berries was further confirmed by TLC.     

Comparison of Real-Time Instruments Used To Monitor Airborne Particulate Matter

ABSTRACT

Measurements collected using five real-time continuous airborne particle monitors were compared to measurements made using reference filter-based samplers at Bakers-field, CA, between December 2, 1998, and January 31, 1999. The purpose of this analysis was to evaluate the suitability of each instrument for use in a real-time continuous monitoring network designed to measure the mass of airborne particles with an aerodynamic diam less than 2.5 μm (PM_2.5) under wintertime conditions in the southern San Joaquin Valley. Measurements of airborne particulate mass made with a beta attenuation monitor (BAM), an integrating nephelometer, and a continuous aerosol mass monitor (CAMM) were found to correlate well with reference measurements made with a filter-based sampler. A Dusttrak aerosol sampler overestimated airborne particle concentrations by a factor of ~3 throughout the study. Measurements of airborne particulate matter made with a tapered element oscillating microbalance (TEOM) were found to be lower than the reference filter-based measurements by an amount approximately equal to the concentration of NH₄NO₃ observed to be present in the airborne particles. The performance of the Dusttrak sampler and the integrating nephelometer was affected by the size distribution of airborne particulate matter. The performance of the BAM, the integrating nephelometer, the CAMM, the Dusttrak sampler, and the TEOM was not strongly affected by temperature, relative humidity, wind speed, or wind direction within the range of conditions encountered in the current study. Based on instrument performance, the BAM, the integrating nephelometer, and the CAMM appear to be suitable candidates for deployment in a real-time continuous PM_2.5 monitoring network in central California for the range of winter conditions and aerosol composition encountered during the study.     

Predicting size-resolved particle behavior in multizone buildings

We compare model predictions to measurements of SF₆ and environmental tobacco smoke particle concentrations in a three-room chamber experiment. To make predictions of multi-room aerosol transport and fate, we linked a multizone airflow model (COMIS) with an indoor aerosol dynamics model (MIAQ4). The linked models provide improved simulation capabilities for predicting aerosol concentrations and exposures in buildings. In this application, we found that the multizone air flow model was vital for predicting the inter-room airflows due to temperature differences between the rooms and when air-sampling pumps were operating during the experiment. Model predictions agree well with measurements, as shown by several comparison metrics. However, predictions of airborne ETS concentrations are slightly lower than measurements. This is mostly attributable to under-stating the source release amount, which we specified independently from literature estimates. Model predictions of ETS particle-size distributions agree with measurements; size bins with the peak concentrations are slightly over-predicted initially, but agree thereafter.     

A simple HPLC method for determination of permethrin residues in wine

An isocratic High Performance Liquid Chromatographic (HPLC) method was optimized for 3-phenoxybenzyl (1RS)-cis-trans-3-(2,2-dichlorovinyl)-2,2-dimethyl-cyclopropanecarboxylate (permethrin) residues identification and quantification in wine matrix. Analytical reverse phase (RP) C-18 column was used (25 cm × 4 mm i.d., 5 μ m) with mobile phase consisting of acetonitrile and water in ratio 70 %/30 % (v v^?1), flow-rate 2.0 mL min^?1, UV-detection at 215 nm and controlled oven temperature at 25°C. The peaks of isomers were identified with the retention times as compared to standard cis-/trans- mixture and confirmed with characteristic spectra using photodiode array detector. Under these conditions, permethrin isomers were well separated with resolution 2.8 and no interference with the naturally present wine compounds was observed. The method was validated for linearity, precision, accuracy, limit of detection (LOD) and limit of quantification (LOQ). Linear regression analysis data proved a good linear relationship (correlation coefficients, r², for cis- and trans-isomer are: 0.9995 and 0.9997, respectively) between response of the detector and concentration of permethrin isomers over a wide concentration range for both isomers (0.55 mg L^?1 ?4.40 mg L^?1). Experimental data showed mean recoveries between 93.95% and 96.58% with RSD values in range: 0.89% ?3.69%. The effect of ethanol content in the solvent on permethrin isomers peak areas was also studied and 60% v v^?1 ethanol was found to be optimal for sample preparation. The method was successfully tested on 20 commercial wine samples from the market in which no permethrin was detected. Thus, it was proved that it is suitable for routine permethrin residues analysis. The proposed method is suitable for routine analysis because of the simple sample preparation, acceptable run-time, low cost and its applicability with conventional instruments.     

Dust Deposit Profiles in a High Velocity Pulse-Jet Fabric Filter

Dust deposit profiles in a pilot-scale pulse-jet fabric filter were measured using a beta gauge. Fly ash was collected on polyester needled felt bags, and the dust profiles were measured after the test system was operated to equilibrium at superficial filtration velocities of 50, 75,100,125, and 150 mm/s. The profiles measured show that a large mass of dust is retained on the fabric of a pulse-jet filter when operated at high filtration velocities. This dust mass retention can be caused by two mechanisms: the failure to remove dust from the fabric during a cleaning pulse, and the redeposition of suspended dust onto the fabric after a cleaning pulse. The dust deposit measured at the highest test velocity was found to be much different from the deposits measured at all other velocities. The deposit found at 150 mm/s had almost twice the average areal density and was more evenly distributed than the deposits found at lower velocities.