地下水中轻质有机污染物(LNAPL)透镜体研究

在二维砂槽模型中模拟了轻质油在均匀多孔介质地下水非饱和区中的运移过程。模拟结果表明,地下水毛细区是轻质油污染的重点区,除了ＬＮＡＰＬ的残留以外,进入地下水饱和的ＬＮＡＰＬ终将被地下水顶托回到毛细区中,毛细区以上的约大多民将在重力作用下进入毛细区中,试验中观察到达稳定状态时ＬＮＡＰＬ透镜体的上边缘略微高出毛细区。利用多孔介质毛细管模型,建立了利用界面张力、接触角、介质特征孔隙直径等物理量估算不同位置     

Remediation of NAPL below the water table by steam-induced heat conduction

Previous experimental studies have shown that NAPL will be removed when it is contacted by steam. However, in full-scale operations, steam may not contact the NAPL directly and this is the situation addressed in this study. A two-dimensional intermediate scale sand box experiment was performed where an organic contaminant was emplaced below the water table at the interface between a coarse and a fine sand layer. Steam was injected above the water table and after an initial heating period the contaminant was recovered at the outlet. The experiment was successfully modeled using the numerical code T2VOC and the dominant removal mechanism was identified to be heat conduction induced boiling of the separate phase contaminant. Subsequent numerical modeling showed that this mechanism was insensitive to the porous medium properties and that it could be evaluated by considering only one-dimensional heat conduction.     

Transport of Escherichia coli through variably saturated sand columns and modeling approaches

A sand column leaching system with well-controlled suction and flow rate was built to investigate the effects on bacterial transport of air-water interface effects (AWI) correlated to water content, particle size, and column length. Adsorption of Escherichia coli strain D to silica sands was measured in batch tests. The average % adsorption for coarse and fine sands was 45.9+/-7.8% and 96.9+/-3.2%, respectively. However, results from static batch adsorption experiments have limited applicability to dynamic bacterial transport in columns. The early breakthrough of E. coli relative to bromide was clear for all columns, namely c. 0.15 to 0.3 pore volume earlier. Column length had no significant effects on the E. coli peak concentration or on total recovery in leachate, indicating retention in the top layer of sands. Tailing of breakthrough curves was more prominent for all fine sand columns than their coarse sand counterparts. Bacterial recovery in leachate from coarse and saturated sand columns was significantly higher than from fine and unsaturated columns. Observed data were fitted by the convection-dispersion model, amended for one-site and two-site adsorption to particles, and for air-water interface (AWI) adsorption. Among all models, the two-site+AWI model achieved consistently high model efficiency for all experiments. Thus it is evident from experimental and modeling results that AWI adsorption plays an important role in E. coli transport in sand columns.     

Infiltration and redistribution of perchloroethylene in partially saturated, stratified porous media

Contamination of the subsurface by nonaqueous phase liquids (NAPLs) is a widespread problem. To investigate the behavior of a nonspreading, dense NAPL (DNAPL) in the vadose zone, we conducted perchloroethylene (PCE) infiltration experiments in nominally 1- and 2-dimensional (D), stratified porous media. In addition, the usefulness and limitations of a multifluid flow simulator to describe PCE infiltration and redistribution under the experimental conditions were tested. The physical simulations were conducted in a column (1-D) and a flow container (2-D) which were packed with two distinct layers of coarse-grained sand and a fine-grained sand layer in between. Volumetric water and PCE contents were determined with a fully automated dual-energy gamma radiation system. While migrating through the drier parts of the coarse-grained sand layers, PCE appeared to wet the water–air interface rather than displacing any water. In the wetter parts of the porous medium, PCE displaced water and behaved as a true nonwetting fluid. PCE showed a limited response to gradients in capillary pressure and rather high values for the volumetric PCE content were measured in the fine-grained sand layers. This was attributed to the nonspreading nature of PCE. The multifluid flow simulator appeared to predict the initial PCE movement in the vadose zone reasonably well. However, the model was not capable of predicting the final amounts of PCE retained in either the unsaturated or saturated part of the flow domain, mainly because the simulator does not consider the nonspreading flow behavior of NAPLs.     

Two-dimensional laboratory simulation of LNAPL infiltration and redistribution in the vadose zone

A quantitative two-dimensional laboratory experiment was conducted to investigate the immiscible flow of a light non-aqueous phase liquid (LNAPL) in the vadose zone. An image analysis technique was used to determine the two-dimensional saturation distribution of LNAPL, water and air during LNAPL infiltration and redistribution. Vertical water saturation variations were also continuously monitored with miniature resistivity probes. LNAPL and water pressures were measured using hydrophobic and hydrophilic tensiometers. This study is limited to homogeneous geological conditions, but the unique experimental methods developed will be used to examine more complex systems. The pressure measurements and the quantification of the saturation distribution of all the fluids in the entire flow domain under transient conditions provide quantitative data essential for testing the predictive capability of numerical models. The data are used to examine the adequacy of the constitutive pressure-saturation relations that are used in multiphase flow models. The results indicate that refinement of these commonly used hydraulic relations is needed for accurate model prediction. It is noted in particular that, in three-fluid phase systems, models should account for the existence of a residual NAPL saturation occurring after NAPL drainage. This is of notable importance because residual NAPL can act as a non negligible persistent source of contamination.     

表面活性剂强化抽出处理含水层中DNAPL污染物的去除特征

为明确表面活性剂强化抽出处理含水层中DNAPL污染物过程中表面活性剂的增强修复效果,及DNAPL自身理化性质和介质孔径的影响,利用数码图像分析技术对1,2-二氯乙烷和四氯乙烯2种DNAPL在石英砂填充的二维砂箱中的抽取迁移过程进行了实验模拟研究,并对抽出水样中DNAPL的浓度进行了测试分析。结果表明,实验条件下加入低浓度(0.18%)的十二烷基苯磺酸钠(SDBS)大幅提高了对弱透水层截留的2种DNAPL聚集体的抽出处理效率。1,2-二氯乙烷在该表面活性剂溶液中的表观溶解度远高于四氯乙烯,因此其短时间内的绝对去除率更高。SDBS强化抽出处理DNAPL的作用机理以增溶作用为主,而其增流作用使DNAPL迁移流动后分布面积增大,增加了与表面活性剂溶液接触的面积,对增溶作用起到促进效果。细粒介质中DNAPL迁移后的最大分布面积较大,因此体系中DNAPL的溶解速率较高。在DNAPL聚集体质量与水力梯度固定的条件下,油水界面张力越低,DNAPL的密度越大,DNAPL垂向迁移的风险就越大。本研究为修复工程中如何依据DNAPL种类与场地多孔介质的情况选择表面活性剂提供了参考。     

Removal of DNAPL contamination from the saturated zone by the combined effect of vertical upward flushing and density reduction

A common aspect of innovative remediation techniques is that they tend to reduce the interfacial tension between the aqueous and non-aqueous phase liquids, resulting in mobilization of the organic contaminant. This complicates the remediation of aquifers, contaminated with Dense Non-Aqueous Phase Liquids (DNAPLs), as they are likely to migrate downwards, deeper into the aquifer and into finer layers. A possible solution is the use of swelling alcohols, which tend to reduce the density difference between the aqueous phase and the DNAPL. To avoid premature mobilization upon the initial contact between the DNAPL and the alcohol, several researchers have proposed the use of vertical upward flow of the alcohol. In this paper, we present an equation, which describes the upward mobilization of both continuous and discontinuous DNAPLs and so the important parameters governing the upward controlled mobilization of the DNAPL. The need and required magnitude of this specific discharge was investigated by conducting four column experiments in which the initial density of the DNAPL and the permeability was varied. It was shown that the required flow velocities increase with the permeability of the porous medium and the initial density difference between the aqueous phase and the DNAPL. Whenever the specific discharge falls below the critical value, the DNAPL moves downward. A second set of column experiments looked at the impact of permeability of porous medium on the solubilization and mobilization of DNAPL during alcohol flooding. Columns, packed with coarse or fine sand, containing a residual trichloroethylene (TCE) or perchloroethylene (PCE) saturation were flushed with the alcohol mixture at a fixed specific discharge rate. The induced pressure gradients in the aqueous phase, which were higher in the fine sand, resulted for this porous medium in extensive mobilization of the DNAPL against the direction of the buoyancy force. The density of the first NAPL coming out of the top of the fine sand was close to that of the pure DNAPL. In the coarser sand, the pressure gradients were sufficient to prevent downward migration of the DNAPL, but upward mobilization was minimal. The predominant removal mechanism in this case was the much slower solubilization.     

Infiltration of PCE in a system containing spatial wettability variations

A two-dimensional infiltration experiment was conducted to investigate and quantify the effect of spatial wettability variations on DNAPL migration and entrapment in saturated sands. Experimental observations of tetrachloroethylene (PCE) infiltration showed that organic-wet sand lenses acted as very effective capillary barriers, retaining PCE and inhibiting its downward migration. A multiphase numerical simulator was used to model this sand box experiment. The simulator incorporates wettability-modified van Genuchten and Brooks-Corey capillary pressure/saturation relationships as well as Burdine and Mualem relative permeability relationships. PCE mass distributions, estimated by image analysis of digital photographs taken during the infiltration event, were compared to simulation results. Although both relative permeability models were qualitatively able to predict the PCE retention in the organic-wet layers, simulations with the Mualem model failed to capture the observed rate of PCE migration. A traditional multiphase simulator, incorporating water-wet capillary retention relations, failed to predict both PCE pathways and retention behavior. This study illustrates the potential influence of subsurface wettability variations on DNAPL migration and entrapment and supports the use of modified capillary relations in conjunction with the Burdine model in multiphase flow simulators.     

Modeling dissolution and volatilization of LNAPL sources migrating on the groundwater table

A vertically averaged two-dimensional model was developed to describe areal spreading and migration of light nonaqueous-phase liquids (LNAPLs) introduced into the subsurface by spills or leaks from underground storage tanks. The NAPL transport model was coupled with two-dimensional contaminant transport models to predict contamination of soil gas and groundwater resulting from a LNAPL migrating on the water table. Numerical solutions were obtained by using the finite-difference method. Simulations and sensitivity analyses were conducted with a LNAPL of pure benzene to study LNAPL migration and groundwater contamination. The model was applied to subsurface contamination by jet fuel. Results indicated that LNAPL migration were affected mostly by volatilization. The generation and movement of the dissolved plume was affected by the geology of the site and the free-product plume. Most of the spilled mass remained as a free LNAPL phase 20 years after the spill. The migration of LNAPL for such a long period resulted in the contamination of both groundwater and a large volume of soil.     

粗石英砂层厚度及倾角对核废物处置库顶盖毛细屏障效应的影响

毛细屏障作为核废物处置库顶盖的工程屏障之一,已经在国内外得到了广泛应用.采用箱体实验方法,研究了非饱和稳定流条件下粗石英砂层厚度和倾角对毛细屏障效应的影响.结果表明,随着粗石英砂层厚度的增大,水分的相对绕流量增大,毛细屏障效应增强;随着粗石英砂层倾角的增大,其表面积水减少,水的横向流动能力增强,毛细屏障效应增强.     

Experimental investigation of pneumatic soil vapor extraction

Soil Vapor Extraction (SVE) is a common remediation technique for removing volatile organic compounds from unsaturated contaminated soils. Soil heterogeneities can however cause serious limitations to the applicability of SVE due to air bypassing low permeable areas of the soil, leading to diffusion limitation of the remediation. To enhance removal from areas subject to diffusion limitation a new remediation technique, pneumatic soil vapor extraction, is proposed. In contrast to traditional SVE, in which soil vapor is extracted continuously by a vacuum pump, pneumatic SVE is based on enforcing a sequence of large pressure drops on the system to enhance the recovery from the low-permeable areas. The pneumatic SVE technique was investigated in the laboratory using TCE as a model contaminant. 2D-laboratory tank experiments were performed on homogeneous and heterogeneous sand packs. The heterogeneous packs consisted of a fine sand lens surrounded by a coarser sand matrix. As expected when using traditional SVE, the removal of TCE from the low permeable lens was extremely slow and subject to diffusion limitation. In contrast when pneumatic venting was used removal rates increased by up to 77%. The enhanced removal was hypothesized to be attributed to mixing of the contaminated air inside the lens and generation of net advective transport out of the lens due to air expansion.     

Impact of varying soil structure on transport processes in different diagnostic horizons of three soil types

When soil structure varies in different soil types and the horizons of these soil types, it has a significant impact on water flow and contaminant transport in soils. This paper focuses on the effect of soil structure variations on the transport of pesticides in the soil above the water table. Transport of a pesticide (chlorotoluron) initially applied on soil columns taken from various horizons of three different soil types (Haplic Luvisol, Greyic Phaeozem and Haplic Cambisol) was studied using two scenarios of ponding infiltration. The highest infiltration rate and pesticide mobility were observed for the Bt₁ horizon of Haplic Luvisol that exhibited a well-developed prismatic structure. The lowest infiltration rate was measured for the Bw horizon of Haplic Cambisol, which had a poorly developed soil structure and a low fraction of large capillary pores and gravitational pores. Water infiltration rates were reduced during the experiments by a soil structure breakdown, swelling of clay and/or air entrapped in soil samples. The largest soil structure breakdown and infiltration decrease was observed for the Ap horizon of Haplic Luvisol due to the low aggregate stability of the initially well-aggregated soil. Single-porosity and dual-permeability (with matrix and macropore domains) flow models in HYDRUS-1D were used to estimate soil hydraulic parameters via numerical inversion using data from the first infiltration experiment. A fraction of the macropore domain in the dual-permeability model was estimated using the micro-morphological images. Final soil hydraulic parameters determined using the single-porosity and dual-permeability models were subsequently used to optimize solute transport parameters. To improve numerical inversion results, the two-site sorption model was also applied. Although structural changes observed during the experiment affected water flow and solute transport, the dual-permeability model together with the two-site sorption model proved to be able to approximate experimental data.     

Multidimensional validation of a numerical model for simulating a DNAPL release in heterogeneous porous media

A fixed-volume release of 1,2-DCE, tracked in space and time with a light transmission/image analysis system, provided a data set for the infiltration, redistribution, and immobilisation of a dense non-aqueous phase liquid (DNAPL) in a heterogeneous porous medium. The two-dimensional bench scale flow cell was packed with a spatially correlated, random heterogeneous distribution of six sand types. In order to provide the necessary modelling parameters, detailed constitutive relationships were measured at the local scale for the six sands. These experiments revealed that nonwetting phase (NWP) relative permeability-saturation (k(rN)-S(W)) relationships are strongly correlated to sand type. Trends in the best-fit k(rN)-S(W) parameters reflected a positive correlation between mean grain diameter and the maximum NWP relative permeability, k(rN)(max). Multiphase flow simulations of the bench scale experiment best reproduced the experimental observations, producing excellent matches in both time and space, when the measured, correlated local scale k(rN)-S(W) relationships were employed.     

The reactive transport of trichloroethene is influenced by residence time and microbial numbers

The dechlorination rate in a flow-through porous matrix can be described by the species specific dechlorination rate observed in a liquid batch unless mass transport limitations prevail. This hypothesis was examined by comparing dechlorination rates in liquid batch with that in column experiments at various flow rates (3-9-12 cm day(-1)). Columns were loaded with an inoculated sand and eluted with a medium containing 1mM trichloroethene (TCE) for 247 days. Dechlorination in the column treatments increased with decreasing flow rate, illustrating the effect of the longer residence time. Zeroth order TCE or cis-DCE degradation rates were 4-7 folds larger in columns than in corresponding batch systems which could be explained by the higher measured Geobacter and Dehalococcoides numbers per unit pore volume in the columns. The microbial numbers also explained the variability in dechlorination rate among flow rate treatments marked by a large elution of the dechlorinating species' yield as flow increased. Stop flow events did not reveal mass transport limitations for dechlorination. We conclude that flow rate effects on reactive transport of TCE in this coarse sand are explained by residence time and by microbial transport and that mass transport limitations in this porous matrix are limited.     

多孔介质中轻非水相液体污染物多相流体系的电阻率特性试验研究

目前,对于多孔介质中轻非水相液体(LNAPL)污染物的电阻率特性存在2种截然相反的观点,影响了LNAPL污染场地电阻率资料的解释结果。为此,通过自行设计的装置进行试验,重点探讨电阻率与砂样颗粒粒径、含水量和LNAPL饱和度等参数之间的变化关系。结果发现,在砂样被LNAPL饱和过程中,砂样的颗粒粒径和含水量对其电阻率相对值的变化有重大影响,含水量低的砂样电阻率相对值变化幅度很小,而含水量高的砂样电阻率相对值变化幅度很大,粗粒径的砂样电阻率相对值的变化明显高于细颗粒砂样。对于"水-油-气"三相体系和"水-油"二相体系,电阻率和含水量的关系曲线均可用Archie公式很好拟合。该试验结果对于提高LNAPL污染场地电阻率资料的解释结果的准确度具有重要的意义,在确定相关的参数如渗透系数、LNAPL饱和度等方面具有重要的实际应用价值。     

Droplet evaporation from porous surfaces; model validation from field and wind tunnel experiments for sand and concrete

The evaporation model of Roberts and Griffiths (1995 Atmospheric Environment 29, 1307–1317) has been subjected to an extensive validation exercise based on a major campaign of field experiments on evaporation from surfaces composed of sand and of concrete. This complements the previous validation which was limited to wind tunnel experiments on sand surfaces. Additionally, the validation using wind tunnel data has been extended to include concrete surfaces. The model describes the constant-rate and falling-rate periods that characterise evaporation from porous media. During the constant-rate period, the evaporation is solely determined by the vapour transport rate into the air. During the falling-rate period, the process in the porous medium is modelled as a receding evaporation front, the overall evaporation rate being determined by the combined effects of vapour transport through the pore network and subsequently into the air. The field trials programme was conducted at sites in the USA and the UK, and examined the evaporation of diethyl malonate droplets from sand and concrete surfaces. Vapour concentrations at several heights in the plume were measured at the centre of a 1 m radius annular source (of width 10 cm) contaminated by uniformly sized droplets (2.4 or 4.1 mm in diameter), key meteorological data being measured at the same time. The evaporation was quantified by coupling concentration and wind speed data. In all, 22 trials were performed on sand and concrete; a further 8 were performed on non-porous surfaces (aluminium foil and slate) as references. The model performance was evaluated against the experimental data in terms of two quantities, the initial evaporation rate of the embedded droplets, and the mass-fraction remaining in the substrate at intervals over the evaporation episode. Overall, the model performance was best in the case of the field experiments for concrete, and the wind tunnel experiments for sand; the performance for wind tunnel experiments for concrete was reasonably good; in the case of the field experiments for sand there was significant underprediction of evaporation rates, though the trends with the determining variables were well predicted.     

A pragmatic approach for estimation of source-zone emissions at LNAPL contaminated sites

When considering natural attenuation as a remediation strategy at a site contaminated by a light non-aqueous phase liquid (LNAPL), it is important to consider the emission of contaminants from the source zone. A quantification of source-zone emissions is essential both for comparison with down-gradient mass fluxes to provide an estimate of fractional mass flux reduction, as well as for estimating the source lifetime. Because the spatial distribution of LNAPL at a field site is strongly dependent on both the spill circumstances and the heterogeneity of the geologic materials, which can be problematic for in-situ determination, alternative methods for estimating source-zone emissions are needed. In this work, a three-dimensional multiphase flow and transport modelling approach is used to investigate the relationship between the lateral extent of an LNAPL body and the emission of contaminants to groundwater at a contaminated site. For simulations involving an LNAPL release in an aquifer comprised of heterogeneous porosity and permeability distributions that were generated geostatistically, it is shown that a simple linear relationship exists between the lateral extent of the LNAPL body in the capillary fringe and the emission to the aqueous phase. The parameters describing the relationship are found to be linear functions of the groundwater flow velocity and the vertical infiltration rate. This site-specific relationship provides a simple method to estimate contaminant emissions to groundwater at LNAPL contaminated sites.     

Filtration and transport of Bacillus subtilis spores and the F-RNA phage MS2 in a coarse alluvial gravel aquifer: implications in the estimation of setback distances

Filtration of Bacillus subtilis spores and the F-RNA phage MS2 (MS2) on a field scale in a coarse alluvial gravel aquifer was evaluated from the authors' previously published data. An advection-dispersion model that is coupled with first-order attachment kinetics was used in this study to interpret microbial concentration vs. time breakthrough curves (BTC) at sampling wells. Based on attachment rates (katt) that were determined by applying the model to the breakthrough data, filter factors (f) were calculated and compared with f values estimated from the slopes of log (cmax/co) vs. distance plots. These two independent approaches resulted in nearly identical filter factors, suggesting that both approaches are useful in determining reductions in microbial concentrations over transport distance. Applying the graphic approach to analyse spatial data, we have also estimated the f values for different aquifers using information provided by some other published field studies. The results show that values of f, in units of log (cmax/co) m(-1), are consistently in the order of 10(-2) for clean coarse gravel aquifers, 10(-3) for contaminated coarse gravel aquifers, and generally 10(-1) for sandy fine gravel aquifers and river and coastal sand aquifers. For each aquifer category, the f values for bacteriophages and bacteria are in the same order-of-magnitude. The f values estimated in this study indicate that for every one-log reduction in microbial concentration in groundwater, it requires a few tens of meters of travel in clean coarse gravel aquifers, but a few hundreds of meters in contaminated coarse gravel aquifers. In contrast, a one-log reduction generally only requires a few meters of travel in sandy fine gravel aquifers and sand aquifers. Considering the highest concentration in human effluent is in the order of 10(4) pfu/l for enteroviruses and 10(6) cfu/100 ml for faecal coliform bacteria, a 7-log reduction in microbial concentration would comply with the drinking water standards for the downgradient wells under natural gradient conditions. Based on the results of this study, a 7-log reduction would require 125-280 m travel in clean coarse gravel aquifers, 1.7-3.9 km travel in contaminated coarse gravel aquifers, 33-61 m travel in clean sandy fine gravel aquifers, 33-129 m travel in contaminated sandy fine gravel aquifers, and 37-44 m travel in contaminated river and coastal sand aquifers. These recommended setback distances are for a worst-case scenario, assuming direct discharge of raw effluent into the saturated zone of an aquifer. Filtration theory was applied to calculate collision efficiency (alpha) from model-derived attachment rates (katt), and the results are compared with those reported in the literature. The calculated alpha values vary by two orders-of-magnitude, depending on whether collision efficiency is estimated from the effective particle size (d10) or the mean particle size (d50). Collision efficiency values for MS-2 are similar to those previously reported in the literature (e.g. ) [DeBorde, D.C., Woessner, W.W., Kiley, QT., Ball, P., 1999. Rapid transport of viruses in a floodplain aquifer. Water Res. 33 (10), 2229-2238]. However, the collision efficiency values calculated for Bacillus subtilis spores were unrealistic, suggesting that filtration theory is not appropriate for theoretically estimating filtration capacity for poorly sorted coarse gravel aquifer media. This is not surprising, as filtration theory was developed for uniform sand filters and does not consider particle size distribution. Thus, we do not recommend the use of filtration theory to estimate the filter factor or setback distances. Either of the methods applied in this work (BTC or concentration vs. distance analyses), which takes into account aquifer heterogeneities and site-specific conditions, appear to be most useful in determining filter factors and setback distances.     

人工快速渗滤系统堵塞-恢复实验研究

采用干湿交替间歇进水的运行方式,以不同粒径的河砂为填料构建3组人工快速渗滤(CRI)系统,研究CRI系统的堵塞-恢复规律,填料粒径与系统出水COD、水力负荷和纳污量之间的关系,以及环境温度对系统处理效率的影响。结果表明,CRI系统堵塞后经过一段时间的恢复期即可以自然恢复活性。细砂CRI系统的稳定性最好,出水COD最稳定,抗冲击能力和纳污量强于混砂和粗砂CRI系统。当温度在适宜微生物生长的范围内波动时,对系统处理效率的影响并不明显。实际工程应建造多级系统或并行系统解决堵塞问题,以保证系统的水力负荷和稳定运行。     

Equilibrium nonaqueous phase liquid pool geometry in coarse soils with discrete textural interfaces

This paper presents a model for the geometry of nonaqueous phase liquid (NAPL) pools and mounds in homogeneous soils and soils with discrete textural interfaces. It is shown that the concepts of capillary pressure-saturation curve hysteresis and entry pressures are integral to the complete conceptualization of pool and mound geometry. Unless hysteresis is included in the analysis, light NAPL (LNAPL) in homogeneous soils cannot exist in pools at all, and dense NAPL (DNAPL) will not mound on horizontal textural interfaces unless lateral confining boundaries are present. The proposed model also implies that remobilization of DNAPL pools will occur at lower hydraulic gradients than those predicted with previous models. Comparing predicted and experimental DNAPL and LNAPL pool thicknesses and the location of an LNAPL lens with respect to the top of the capillary fringe validate the model.