Changes of Surface Properties of Yeast Cell Wall Under Exposure of Electromagnetic Field (40.68 MHz) and Action of Nystatin

Summary Changes of the surface properties were studied in the cell wall of the yeast Saccharomyces cerevisiae Y-517 under influence of the electromagnetic field (EMF) (40.68 MHz) and lethal doses of the fungicidal antibiotic nystatin (10 μg/10⁶ cells). Atomic force microscopy was used to study surface topography and visco-elastic properties of the cell walls. Surface carbohydrates were detected by lectins marked with gold with the help of the scanning electron microscope. Additional polysaccharide layer appeared over cell surface after EMF exposure. We suggest that electromagnetic fields resulted in the change of the cell surface, and, accordingly, the sensitivity of organisms to the antifungal antibiotics.     

军用电子组件(PCBA)失效分析技术与案例

随着武器装备集成化、高密度化和轻量化的发展,大量的高密度器件如BGA、CSP得到了广泛的应用,由此作为武器装备心脏的军用电子组件的组装密度也越来越高。伴随着电子组件组装密度的提高,对于电子组件的组装技术也提出了更高的要求。然而,由于军用电子组件器件种类繁多,导致其电子组装工艺复杂,加上我国装备制造企业的工艺水平较国际先进企业相比还存在很大的差距,军用电子组件存在较为严重的工艺缺陷和可靠性问题。大量的工艺缺陷如润湿不良、焊点空洞、焊点机械强度差和疲劳寿命低严重影响了军用电子组件的质量和可靠性,并制约了武器装备的发展。本文针对军用电子组件存在的焊接缺陷、绝缘性失效(CAF和ECM)以及焊点疲劳失效的主要问题,介绍了军用电子组件常用的失效分析方法和手段,包括金相切片分析、声学扫描分析、扫描电镜与能谱、热分析以及傅立叶红外光谱分析等。然后结合军用电子组件的典型的失效分析案例,介绍这些分析技术在实际的案例中的应用。PCBA失效机理与原因的获得将有利于将来对PCBA的质量控制以避免类似问题的再度发生。     

Development of a novel fungal consortium for the treatment of molasses distillery wastewater

In India, cane molasses–based distilleries are major production centers of ethanol. These industries release a dark brown colored effluent known as spent wash, which even after anaerobic treatment retains the color. The commonly used practices of treatment fail to remove the color and COD. A novel fungal consortium was developed for the treatment of this recalcitrant wastewater. The consortium was run on a bioreactor with undiluted distillery effluent for 40 days. In the first 14 days, 61.5% color and 65.4% COD removal was achieved. Further, the fungi were able to use wheat straw as carbon source as evidenced by scanning electron microscopy (SEM) while treating the distillery wastewater. It is expected that such a treatment step will lead to development of a treatment technology for distillery wastewater without the need for diluting it.     

Electricity nanogenerator from egg shell membrane: A natural waste bioproduct

ABSTRACT

In the era of developing technologies, there is always been a crisis of rising demands of energy. There is no skepticism that a lot of energy is being produced every hour for almost each and every field, but still an exploration is needed to come up with new and viable options for energy creation. The same is the objective of this paper which proposes the use of waste biomaterials in association with organic and inorganic materials as a source of energy to power up small electronic devices. In this research egg shell membrane (ESM)-based triboelectric nanogenerator (TENG) is proposed in combination with calotropis (Calo), cellulose from fruit of Bombax Ceiba (BOM), cellulose in form of tissue paper (TISU), dog hair (DH), polytetrafluoroethylene (PTFE), aluminum (Al), and copper (Cu). ESM is eco-friendly waste food by-product and available in abundance. Characterization of ESM is done by scanning electron microscope (SEM), atomic force microscope (AFM), X-ray diffraction (XRD), and Fourier transform infrared spectrophotometer (FTIR). The proposed ESM-PTFE-based TENG power up 462 green LEDs (462 × 2 V = 924 V ~ 1 kV) without rectifier and produced up to 7.61 µJ energy with 4.7 µF capacitor at 200 tapings. All the proposed ESM-based TENG combinations generate sufficient voltage to turn ON the wrist watch. This green-energy-based TENG has potential application in various fields especially related to medical devices.     

Use of alkaline extraction to quantify sulfate concentration in oxidized mine tailings

An alkaline extraction method has been developed for the determination of total sulfate in mine tailings containing secondary sulfate minerals formed by the oxidation of primary sulfides. Oxidized tailings were extracted with a 0.3 M NaOH solution at a liquid/solid ratio of 30 at room temperature for 16 h. The sulfate concentration in the extracts was determined by ion chromatography (IC). The coefficient of variation for sulfate determinations ranged from 1.9 to 3.2% for five tailings samples collected at two tailings impoundments. Mineralogical analysis of the tailings by scanning electron microscopy/X-ray energy dispersive spectrometry (SEM/EDS) demonstrated that the extraction of sulfate was complete, with the exception of extremely insoluble barite. The proposed method is simple, yields an accurate yet rapid measurement of sulfate, and involves a safer laboratory operation than conventional methods that make use of strong HCl acid solutions. Moreover, this method allows the specific measurement of sulfate in the extract, whereas conventional methods are generally limited to the measurement of total S by inductively coupled plasma atomic emission spectrometry (ICP-AES) due to the interference of chloride with sulfate in IC.     

An analysis of urban development and its environmental impact on the Tampa Bay watershed

Urbanization has transformed natural landscapes into anthropogenic impervious surfaces. Urban land use has become a major driving force for land cover and land use change in the Tampa Bay watershed of west-central Florida. This study investigates urban land use change and its impact on the watershed. The spatial and temporal changes, as well as the development density of urban land use are determined by analyzing the impervious surface distribution using Landsat satellite imagery. Population distribution and density are extracted from the 2000 census data. Non-point source pollution parameters used for measuring water quality are analyzed for the sub-drainage basins of Hillsborough County. The relationships between 2002 urban land use, population distribution and their environmental influences are explored using regression analysis against various non-point source pollutant loadings in these sub-drainage basins. The results suggest that strong associations existed between most pollutant loadings and the extent of impervious surface within each sub-drainage basin in 2002. Population density also exhibits apparent correlations with loading rates of several pollutants. Spatial variations of selected non-point source pollutant loadings are also assessed.     

Ink and dirt behavior in pulping after artificial aging of cold-set offset printed newspapers in different humidity conditions

Although moisture has a decisive role in the permanence of cellulose and unprinted paper, its role in ink release from the surface of printed recovered papers remains unclear. This work aimed to determine whether various relative humidity levels in the artificial aging test affect ink release from the surface of the paper and its fibers when pulping cold-set offset printed newspapers in alkaline pulping conditions. The results showed that relative humidity variations from 30% to 70% negligibly affected ink release at 60 °C. However, compared with these lower humidity levels, exposure to 90% relative humidity for at least 25 h resulted in a higher ink content bound to fibers, a greater formation of visible dirt specks after pulping and a smaller formation of microscopic ink particles. In practical applications, the accurate estimation of climate effects during the storage and the transportation of recycled papers requires that humidity conditions are taken into account while performing artificial aging tests with paper products.     

Different formats of imprinted polymers for determining organotin compounds in environmental samples

Organotin compounds and their degradation products enter the environment mainly as a result of their use as biocides and antifouling paints. Analysis of these compounds in environmental samples has to be very sensitive and selective so that their concentrations corresponding to the low environmental target values can also be detected. Generally, analysis of a complex matrix leads to high interferences during the different process steps; clean-up procedures are recommended to overcome this problem. For the past many years, solid phase extraction by employing imprinted materials has been extensively used for many organic substances that are used for pre-concentration and clean-up purposes with excellent results. Here, we present three different imprinted polymers prepared via bulk, precipitation, and emulsion polymerization methods that use similar compositions. The synthesized polymer particles were characterized morphologically by employing scanning electron microscopy and Brunauer-Emmett-Teller analysis. Binding properties were calculated using the Langmuir-Freundlich isotherm. Depending on the properties of the materials, different analytical applications for complex matrices are proposed. These applications are mainly used on tributyltin and its degradation products for environmental analysis.     

A nanocomposite of CoFe2O4-carbon microspheres for electrochemical energy storage applications

A carbon/CoFe₂O₄ composite was synthesized by precipitation method. The morphology of the composite was analyzed using scanning electron microscopy, X-ray diffraction, transmission electron microscopy, Fourier Transform Infrared Spectra, and vibrating sample magnetometry. The electrocapacitive behaviors of the composite has been studies by cycle voltammogram and galvanic charge/discharge. The size of the nanoparticles carbon composite of CoFe₂O₄ was uniform and 209 nm. Due to a high percent of carbon, electrochemical measurements showed electrical double layer mechanism. Specifically, the carbon/cobalt ferrite electrode exhibited high specific capacitance of 102.5 F g^?1 at a current density of 0.16 A g^?1, and high rate capability with 30% retention of capacitance even up to 20 A g^?1, and excellent cycling stability with 81.5% retention of the initial capacitance after 6000 charge/discharge cycles, supporting that the carbon cobalt ferrite composite electrode could be a potential candidate for supercapacitor application.     

The role of atmospheric transformations in determining environmental impacts of carbonaceous nanoparticles

In studies that have explored the potential environmental impacts of manufactured nanomaterials, the atmosphere has largely been viewed as an inert setting that acts merely as a route for inhalation exposure. Manufactured nanomaterials will enter the atmosphere during production, use, and disposal, and rather than simply being transported, airborne nanoparticles are in fact subject to physical and chemical transformations that could modify their fate, transport, bioavailability, and toxicity once they deposit to aqueous and terrestrial ecosystems. The objective of this paper is to review the factors affecting carbonaceous nanomaterials' behavior in the environment and to show that atmospheric transformations, often overlooked, have the potential to alter nanoparticles' physical and chemical properties and thus influence their environmental fate and impact. Atmospheric processing of naturally occurring and incidental nanoparticles takes place through coagulation, condensation, and oxidation; these phenomena are expected to affect manufactured nanoparticles as well. It is likely that carbonaceous nanomaterials in the atmosphere will be oxidized, effectively functionalizing them. By influencing size, shape, and surface chemistry, atmospheric transformations have the potential to affect a variety of nanoparticle-environment interactions, including solubility, interaction with natural surfactants, deposition to porous media, and ecotoxicity. Potential directions for future research are suggested to address the current lack of information surrounding atmospheric transformations of engineered nanomaterials.     

涂铁石英砂吸附水中Cr（Ⅵ）的研究

采用静态吸附和动态过滤的试验方法研究了涂铁石英砂（IOCS）滤料对水中Cr（Ⅵ）的去除,并探讨其吸附机理。研究结果表明,Cr（Ⅵ）在IOCS上的吸附平衡符合Langmuir吸附模型。经氧化铁改性滤料表面电位带正电荷,对水中的Cr（Ⅵ）有良好的去除效果。pH值对Cr（Ⅵ）的去除影响较大,随着溶液的pH值升高,滤料表面电位减小,Cr（Ⅵ）的吸附率也减小。IOCS滤料去除Cr（Ⅵ）机理主要为静电吸附。     

公众参与对环境治理效果的影响——基于阶梯理论的实证研究

近年来,公众已经成为中国环境治理中不可或缺的力量,公众参与的方式和渠道也在不断拓展和丰富。为考察不同类型公众参与方式对环境治理效果的影响差异,本文基于公众参与阶梯理论,选取四类公众参与方式和四类污染物,结合我国2008—2017年30个省份数据,利用面板数据回归模型进行了实证检验。结果表明,横向比较不同类型的公众参与方式,公众环境来访对环境治理的促进效果优于环境信息公开和环保网络舆论,而政协提案、人大议案的积极效应尚不显著。纵向比较不同类型的污染物治理效果,公众参与能显著促进大气污染物的减排,对噪声和固体废物污染效果的影响次之,而在水污染治理中的作用较不理想。建议政府进一步优化健全环境信息公开机制,并重视公众层面的环境诉求,建立公众与地方生态环境部门的良好互动机制,同时鼓励公众通过新媒体渠道参与环境治理。     

KH-550对废PCBs非金属粉/PP复合材料性能的影响

对回收的纸基印刷线路板非金属粉表面硅烷化处理,研究了硅烷偶联剂KH-550最佳用量和对非金属粉/PP复合材料的力学性能以及耐热性能的影响,并通过扫描电镜对复合材料的界面进行研究。结果表明,硅烷偶联剂的最佳用量为非金属粉质量的1.5%;经偶联剂表面处理非金属粉与PP基体树脂能够形成有效的界面粘结,与未处理非金属粉的PP复合体系相比,其力学性能和热性能得到明显提高。硅烷偶联剂KH-550在一定程度上能够改善复合材料的性能。     

CONSTRUCTION WORK FORCE CHARACTERISTICS AND COMMUNITY SERVICE IMPACT ASSESSMENT1

ABSTRACT: Findings of a national survey of the Corps of Engineers construction work force are presented. The purpose of the survey was to obtain information about the construction work force for use in estimating the demand on local community services associated with building Corps projects. Information on numbers of workers and dependents in-migrating to construction sites, the residential location preferences and commuting patterns of this group, and the intentions of this group to remain in local areas after project construction is presented in this paper. An example showing how this information can be used in a community service impact assessment is provided.     

石油开发对辽河油田湿地景观格局变化的影响分析

通过对1989-2009年20年间景观格局的空间分布、变化特征以及变化趋势分析,揭示了造成双台子河自然保护区环境变化的主要驱动力是人类活动和社会经济发展的影响,定量计算了石油开发对研究区域景观格局变化的影响。结果显示:1989-2009年双台河口自然保护区的土地利用类型发生了很大的变化,景观破碎度明显增加,人类活动导致保护区内的土地利用和景观格局也发生了明显变化,但油田开发在总的土地利用变化中的贡献率仅为4.6%。     

Treatment of Landfill Leachate Wastewater by Nanofiltration Membrane

Abstract

Nanofiltration (NF) membrane is an alternative lower energy membrane type compared to reverse osmosis membrane. NF is suitable for rejection of ions and molecules with molecular weight greater than 200 Da. In this study leachate wastewater from a sanitary landfill site in Malaysia was filtered through a NF membrane in order to determine the rejection capability of the membrane towards pollutants such as chemical oxygen demand (COD), conductivity, nitrate, ammonia-nitrogen, and heavy metals such as Pb, Cd, Cu, Zn, Fe. The NF membrane used was HL membrane, which under the atomic force microscope (AFM) imaging, showed visible discrete pores. The overall rejections of the pollutants were more than 85% except for nitrate and ammonia nitrogen. NF can be considered an alternative for advanced filtration especially within a hybrid treatment system combining biological–physical treatment and membrane filtration.     

Ambient monitoring of asbestos in selected Italian living areas

This paper presents the results of an intensive monitoring activity of the particulate, fall-out and soil of selected living areas in Italy with the aim to detect the asbestos concentration in air and subsequent risk of exposure for the population in ambient living environments, and to assess the nature of the other mineral phases composing the particulate matrix. Some areas were sorted out because of the presence of asbestos containing materials on site whereas others were used as blank spots in the attempt to detect the background environmental concentration of asbestos in air. Because the concentration of asbestos in ambient environments is presumably very low, and it is well known that conventional low–medium flow sampling systems with filters of small diameter (25 mm) may collect only a very small fraction of particulate over a short period, for the first time here, an intense monitoring activity was conducted with a high flow sampling system. The high flow system requires the use of large cellulose filters with the advantage that, increasing the amount of collected dust, the probability to collect asbestos fibers increases. Both the protocol of monitoring and analysis are novel and prompted by the need to increase the sensitivity towards the small number of expected fibers. With this goal, the collection of fall-out samples (the particulate falling into a collector filled with distilled water during the monitoring shift) and soil samples was also accomplished. The analytical protocol of the matrix particulate included preliminary X-ray powder diffraction (XRPD), optical microscopy and quantitative electron microscopy (SEM and TEM). Correlations with climatic trends and PM10 concentration data were also attempted.The surprising outcome of this work is that, despite the nature of the investigated site, the amount of dispersed asbestos fibers is very low and invariably lower than the theoretical method detection limits of the SEM and TEM techniques for identification and counting of asbestos fibers. The results are compared to the literature data worldwide and an updated model for asbestos fibers dispersion in ambient environments is proposed.     

Differential Individual Particle Analysis (DIPA): applications in particulate matter characterization

Operator-controlled and computer-controlled scanning electron microscopy (CCSEM) are used extensively to characterize particulate matter in environmental media. Analysis in a scanning electron microscope (SEM) coupled with chemical extraction is a potentially powerful tool that is capable of determining how various sample components are associated at the individual particle level. This involves initial characterization in a SEM, after which the material is exposed to a liquid or gas phase reaction for a specified time, and once exposure is concluded, the particles are reanalyzed in the SEM. This particle analysis by difference, or differential individual particle analysis (DIPA), possesses considerable potential for describing the behavior of environmental particles under changing chemical conditions. Here we describe DIPA applications with illustrative examples drawn from the analysis of particulate matter modified by reactions in a fluid environment. In situ DIPA permits the same particles to be analyzed in the SEM before and after modification. Repeated exposure to the same, or different modifying conditions, provides information on the time dependence of specific reactions. Significant numbers of particles can be analyzed using CCSEM, and the same particles can be analyzed after the reaction by accurate sample relocation in the SEM. Ex situ DIPA, which involves a bulk sample modification, uses CCSEM to characterize significant numbers of particles pre- and postreaction. The CCSEM approach is extremely efficient; recent developments in silicon drift detectors have increased the speed of characteristic X-rays detection, and very large numbers of particles can be analyzed in a short period of time.     

WAVE INDUCED FLOW AND TRANSPORT IN SEDIMENT BEDS1

ABSTRACT: The fate of contaminants in large water bodies is highly influenced by the transfer of flow and solutes across the water sediment interface. In this paper, an analytical model is presented where flow in both sediment bed and open channel is coupled at the interface through a boundary layer occupying the upper part of the sediment bed. The presence of this layer allows not only the capture of the inertia effects through a drag term in the generalized Darcy's equation, but also the specification of different soil parameters for the two porous zones. The flow is advective and driven by wave action along the water surface. The resulting system is solved for the pressure and flux in each sediment layer. The generated transport velocity fields are linked to a random walk simulation that is used to examine the trajectories of solute particles. Comparison of these trajectories against experimental tracer tests suggests a pattern very similar to the one attributed to the presence of surface mounds. The results clearly show the significance of the boundary layer and the drag term for soil with high permeability and the impact of both the thickness of the boundary layer and the length of the gravity wave relative to the depth of the water channel on the transport and exchange across the interface. The paper also examines the sensitivity of the mass exchange to the permeability of the two porous zones.     

Kinetic research on the sorption of aqueous lead by synthetic carbonate hydroxyapatite

The sorption of aqueous lead on carbonate-hydroxyapatite (CHAp) is a complicated non-homogeneous solid/water reaction, which from the kinetic point of view has two stages. In the first stage, the reaction rate is so fast and the kinetic pathway so intricate that further research is required. In the second stage, the reaction rate slows down and the reaction process follows that of a first-order kinetic equation. Experimental results show that the relationship between the reaction rate constant k(1) and temperature T agrees with the Arrhenius equation, and that the activation energy of sorption (E(a)) is 11.93 kJ/mol and the frequency factor (A) is 2.51/s. The reaction rate constant k(1) increases with the Pb(2+) initial concentration and decreasing pH, but with increasing CHAp dosage. X-ray diffraction (XRD), scanning electron microscopy with energy dispersion spectrum (SEM-EDS) and toxicity characteristic leaching procedure (TCLP) tests indicate that the main sorption mechanism is dissolution-precipitation, in conjunction with surface sorption.