Carbon, nitrogen balances and greenhouse gas emission during cattle feedlot manure composting

Carbon and N losses reduce the agronomic value of compost and contribute to greenhouse gas (GHG) emissions. This study investigated GHG emissions during composting of straw-bedded manure (SBM) and wood chip-bedded manure (WBM). For SBM, dry matter (DM) loss was 301 kg Mg(-1), total carbon (TC) loss was 174 kg Mg(-1), and total nitrogen (TN) loss was 8.3 kg Mg(-1). These correspond to 30.1% of initial DM, 52.8% of initial TC, and 41.6% of initial TN. For WBM, DM loss was 268 kg Mg(-1), TC loss was 154 kg Mg(-1), and TN loss was 1.40 kg Mg(-1), corresponding to 26.5, 34.5, and 11.8% of initial amounts. Most C was lost as CO2 with CH4 accounting for <6%. However, the net contribution to greenhouse gas emissions was greater for CH4 since it is 21 times more effective at trapping heat than CO2. Nitrous oxide (N2O) emissions were 0.077 kg N Mg(-1) for SBM and 0.084 kg N Mg(-1) for WBM, accounting for 1 to 6% of total N loss. Total GHG emissions as CO2-C equivalent were not significantly different between SBM (368.4 +/- 18.5 kg Mg(-1)) and WBM (349.2 +/- 24.3 kg Mg(-1)). However, emission of 368.4 kg C Mg(-1) (CO2-C equivalent) was greater than the initial TC content (330.5 kg Mg(-1)) of SBM, raising the question of the net benefits of composting on C sequestration. Further study is needed to evaluate the impact of composting on overall GHG emissions and C sequestration and to fully investigate livestock manure management options.     

Degradation of biomacromolecules during high-rate composting of wheat straw-amended feces

Pig (Sus scrofa) feces, separately collected and amended with wheat straw, was composted in a tunnel reactor connected with a cooler. The composting process was monitored for 4 wk and the degradation of organic matter was studied by two chemical extraction methods, 13C cross polarization magic angle spinning (CPMAS) nuclear magnetic resonance (NMR) and pyrolysis gas chromatography-mass spectrometry (GC-MS). Wet-chemical extraction methods were not adequate to study the degradation of specific organic compounds as the extraction reagents did not give selective separation of hemicellulose, cellulose, proteins, and lignins. A new method was proposed to calculate the contribution of four biomacromolecules (aliphatics, proteins, polysaccharides, and lignin) from the 13C CPMAS NMR spectrum. Pyrolysis GC-MS allowed identification of the composition of the biomacromolecules. The biomacromolecules showed different rates of degradation during composting. High initial degradation rates of aliphatics, hemicellulose, and proteins were observed, where aliphatics were completely degraded and hemicellulose and proteins were partly recalcitrant during the four weeks of composting. The degradation rate of cellulose was much lower and degradation was not completed within the four weeks of composting. Lignin was not degraded during the thermophilic stage of composting but started to degrade slowly during the mesophilic stage. A combination of 13C CPMAS NMR and pyrolysis GC-MS gave good qualitative and semiquantitative assessments of the degradation of biomacromolecules during composting.     

The maturity tests during the composting of municipal solid wastes

This study investigated at first the evolution of co-composting process of municipal solid waste and sewage sludge under Tunisian pedo-climatic conditions.Results showed that the temperature profiles established in the system revealed three classical steps, the mesophilic phase during the first 25 days, the thermophilic phase between 30 and 130 days and the cooling phase began after the 14th week in the two windrows W1 (100% of municipal solid wastes) and W2 (60% of municipal solid wastes and 40% of dried sewage sludge). Potential toxic heavy metal content appeared generally more important in W2 than W1, and both finished products of compost obtained in this study satisfied most parts of the recommended norms of agronomical use. The presence or absence of nitrifying activity allowed determining that the compost W1 was more mature than the compost W2.Composting cannot only transform waste by reducing its harmful effect but also corrects when added to soil, the deficit in organic matter. The nature of the raw material used in composting may affect the quality of the final product. There is a significant need for the amendment of soils by compost. The quality of the amendment may have a significant impact on environment.     

Changes in carbon fractions during composting and maturation of organic wastes

Seven mixtures from four organic residues—an aerobic sewage sludge, a city refuse, a peat residue, and a grape debris—were composted, and the changes undergone by their different carbon fractions during their composting and maturation were studied. In most cases a decrease in carbon fractions during the composting and maturation processes was observed. The extractable carbon, however, increased during maturation. Organic matter mineralization was greater in the composts with city refuse than in those with sewage sludge. The samples with peat residue showed the lowest decreases in carbon fractions. During maturation, an increase of humiclike fraction was observed, which was reflected by a decrease in the soluble carbon-precipitated carbon ratio at pH 2. Water-soluble carbon was the carbon fraction most easily degradable by microorganisms, and its amount correlated significantly with composting time in all the samples.     

The effect of phosphogypsum on greenhouse gas emissions during cattle manure composting

Phosphogypsum (PG), a by-product of the phosphate fertilizer industry, reduces N losses when added to composting livestock manure, but its impact on greenhouse gas emissions is unclear. The objective of this research was to assess the effects of PG addition on greenhouse gas emissions during cattle feedlot manure composting. Sand was used as a filler material for comparison. The seven treatments were PG10, PG20, PG30, S10, S20, and S30, representing the rate of PG or sand addition at 10, 20, or 30% of manure dry weight and a check treatment (no PG or sand) with three replications. The manure treatments were composted in open windrows and turned five times during a 134-d period. Addition of PG significantly increased electrical conductivity (EC) and decreased pH in the final compost. Total carbon (TC), total nitrogen (TN), and mineral nitrogen contents in the final composted product were not affected by the addition of PG or sand. From 40 to 54% of initial TC was lost during composting, mostly as CO(2), with CH(4) accounting for <14%. The addition of PG significantly reduced CH(4) emissions, which decreased exponentially with the compost total sulfur (TS) content. The emission of N(2)O accounted for <0.2% of initial TN in the manure, increasing as compost pH decreased from alkaline to near neutral. Based on the total greenhouse gas budget, PG addition reduced greenhouse gas emissions (CO(2)-C equivalent) during composting of livestock manure by at least 58%, primarily due to reduced CH(4) emission.     

Carbon turnover and ammonia emissions during composting of biowaste at different temperatures

The effects of different process temperatures (40, 55, and 67 degrees C) during composting of source-separated household waste were studied in a 200 L compost reactor at an oxygen concentration of 16%. The overall decomposition measured as carbon mineralization, decomposition of different carbon constituents, and the dynamics of nitrogen mineralization and the microbial community, are reported. Ammonia emissions at 67 degrees C were more than double those at lower temperatures, and they were lowest at 40 degrees C. The decomposition rate, measured as CO2 emission, was highest at 55 degrees C. Decomposition of crude fat was slower at 40 degrees C than at 55 and 67 degrees C. The peak in microbial biomass was largest in the run at 40 degrees C, where substantial differences were seen in the microbial community structure and succession compared to thermophilic temperatures. Biowaste composting can be optimized to obtain both a high decomposition rate and low ammonia emissions by controlling the process at about 55 degrees C in the initial, high-rate stage. To reduce ammonia emissions it seems worthwhile to reduce the temperature after an initial high-temperature stage.     

Degradation of greenhouse twines derived from natural fibers and biodegradable polymer during composting

Commercial composting operations generally do not accept organic wastes with plastic twines from the greenhouse vegetable industry and the bulk of the waste materials ends up in landfills. The objectives of this paper are to identify environmentally compatible substitutes that could replace the current use of petrochemically derived plastic twines in greenhouse vegetable production, thus diverting them from landfills, and to assess the extent of their degradation via composting. Physical properties of the twines, including linear density, percent weight loss and tensile strength were monitored for the biodegradation tests. A pilot-scale composting trial was conducted in an in-vessel composting system. Results showed that the three biodegradable twine materials (cotton, jute and EcoPLA) could degrade readily in a composting environment within a reasonable time frame. Specifically, at the end of 105 days of composting, 85.3%, 84.8% and 81.1% of weight loss was observed for cotton, jute and EcoPLA, respectively. Furthermore, EcoPLA exhibited a slower decline in tensile strength with time, when compared to jute and cotton.     

Physical and chemical changes during composting of wood chip-bedded and straw-bedded beef cattle feedlot manure

In the 1990s, restrictions on incineration encouraged the forest industry in western Canada to develop new uses for their wood residuals by product. One such use was as a replacement for cereal straw bedding in southern Alberta's beef cattle (Bos taurus) feedlot industry. However, use of carbon (C)-rich bedding, such as wood chips, had implications for subsequent composting of the feedlot manure, a practice that was being increasingly adopted. In a 3-yr study, we compared composting of wood chip-bedded manure (WBM) and barley (Hordeum vulgare L.) straw-bedded manure (SBM). There were no significant differences in temperature regimes of SBM and WBM, indicating similar rates of successful composting. Of 17 physical and chemical parameters, five showed significant (P < 0.10) differences due to bedding at the outset of composting (Day 0), and 11 showed significant differences at final sampling (Day 124). During composting (10 sampling times), seven parameters showed significant bedding effects, 16 showed significant time effects, and four showed a Bedding x Time interaction. Significantly lower (P < 0.10) losses of nitrogen (N) occurred with WBM (19%) compared with SBM (34%), which has positive implications for air quality and use as a soil amendment. Other advantages of WBM compost included significantly higher total C (333 vs. 210 kg Mg(-1) for SBM) and inorganic N (1.3 vs. 1.0 kg Mg(-1) for SBM) and significantly lower total phosphorus (4.5 vs. 5.3 kg Mg(-1) for SBM). Our results showed that wood chip bedding should not be a problem for subsequent composting of the manure after pen cleaning. In combination with other benefits, our findings should encourage the adoption of wood chips over straw as a bedding choice for southern Alberta feedlots.     

Recycling for small island tourism developments: Food waste composting at Sandals Emerald Bay,Exuma, Bahamas

The ability for small islands to meet sustainability goals is exacerbated by the costs of transporting goods on, and then, wastes off the islands. At small scales, recycling can be prohibitive and complicated by labor costs; the need to profitably recycle and manage solid waste output from tourism is complicated by scale and available technologies. A multi-year study documents the amount of solid waste generated on Great Exuma (Exuma), The Commonwealth of The Bahamas since 2010 with one year of benchmarking, then limited recycling of food waste generation by an all-inclusive resort, Sandals Emerald Bay (SEB). For the island of Exuma, the rapid increase in the rate of accumulation of solid waste associated with a large destination resort has led to an increase in pests such as rats and flies, along with an increased occurrence of fires associated with unburied solid waste. Solid waste has accumulated faster than the island solid waste management can absorb. SEB kitchen and hotel operations contributes an estimated 36% of all solid waste generated on the island, about 1752 t¹ out of a total of 4841 t generated on the island in 2013 (exclusive of vegetation waste). Based on 4 weeks of benchmarking, 48.5% of all the waste coming out of the SEB resort is compostable, organic waste, but waste composition varies widely over time. Exuma Waste Management (EWM) and Recycle Exuma (RE), both privately-held Bahamian businesses, worked for one year (2012–2013) with SEB resort to implement a benchmarking and pilot recycling project to meet Earth Check green resort certification requirements. This paper outlines the costs and resources required for food waste recycling and some barriers to implementing more effective solid waste management for the tourism industry on small islands.     

Economic and environmental analysis of standard, high efficiency, rainwater flushed, and composting toilets

The current sanitation technology in developed countries is based on diluting human excreta with large volumes of centrally provided potable water. This approach is a poor use of water resources and is also inefficient, expensive, and energy intensive. The goal of this study was to compare the standard sanitation technology (Scenario 1) with alternative technologies that require less or no potable water use in toilets. The alternative technologies considered were high efficiency toilets flushed with potable water (Scenario 2), standard toilets flushed with rainwater (Scenario 3), high efficiency toilets flushed with rainwater (Scenario 4), and composting toilets (Scenario 5). Cost, energy, and carbon implications of these five design scenarios were studied using two existing University of Toledo buildings. The results showed that alternative systems modeled in Scenarios 2, 4, and 5 were viable options both from an investment and an environmental performance perspective. High efficiency fixtures that use potable water (Scenario 2) is often the most preferred method in high efficiency buildings due to reduced water use and associated reductions in annual water and wastewater costs. However, the cost, energy, and CO(2)EE analyses all showed that Scenarios 4 and 5 were preferable over Scenario 2. Cost payback periods of scenarios 2, 4 and 5 were less than 10 years; in the future, increase in water and wastewater services would further decrease the payback periods. The centralized water and wastewater services have high carbon footprints; therefore if carbon footprint reduction is a primary goal of a building complex, alternative technologies that require less potable water and generate less wastewater can largely reduce the carbon footprint. High efficiency fixtures flushed with rainwater (Scenario 4) and composting toilets (Scenario 5) required considerably less energy than direct energy demands of buildings. However, the annual carbon footprint of these technologies was comparable to the annual carbon footprint from space heating. Similarly, the carbon savings that could be achieved from Scenario 4 or 5 were comparable to a recycling program that can be implemented in buildings.     

Lidar quantification of bank erosion in Blue Earth County, Minnesota

Sediment and phosphorus (P) transport from the Minnesota River Basin to Lake Pepin on the upper Mississippi River has garnered much attention in recent years. However, there is lack of data on the extent of sediment and P contributions from riverbanks vis-à-vis uplands and ravines. Using two light detection and ranging (lidar) data sets taken in 2005 and 2009, a study was undertaken to quantify sediment and associated P losses from riverbanks in Blue Earth County, Minnesota. Volume change in river valleys as a result of bank erosion amounted to 1.71 million m over 4 yr. Volume change closely followed the trend: the Blue Earth River > the Minnesota River at the county's northern edge > the Le Sueur River > the Maple River > the Watonwan River > the Big Cobb River > Perch Creek > Little Cobb River. Using fine sediment content (silt + clay) and bulk density of 37 bank samples representing three parent materials, we estimate bank erosion contributions of 48 to 79% of the measured total suspended solids at the mouth of the Blue Earth and the Le Sueur rivers. Corresponding soluble P and total P contributions ranged from 0.13 to 0.20% and 40 to 49%, respectively. Although tall banks (>3 m high) accounted for 33% of the total length and 63% of the total area, they accounted for 75% of the volume change in river valleys. We conclude that multitemporal lidar data sets are useful in estimating bank erosion and associated P contributions over large scales, and for riverbanks that are not readily accessible for conventional surveying equipment.     

Preliminary estimations of energy and cost for CO2 recovery by a membrane flash process utilizing waste thermal energy

The membrane flash process utilizing waste thermal energy was developed to achieve an energy-saving technology and to substitute it for a conventional regenerator. The operating conditions of the membrane flash at high temperature were studied. The petroleum refining process and iron manufacturing process were proposed for candidate processes that actually had waste energy sources. The DEA concentration and the flashing pressure had optimum values to improve the performance and reduce the energy consumption for CO₂ recovery. Energy consumptions and costs for CO₂ recovery in the membrane flash and chemical absorption were estimated by a process simulator and discussed under the same conditions. The membrane flash can achieve lower energy capture than the chemical absorption for the above industrial processes. The membrane flash is suitable for the CO₂ emission sources that had high CO₂ concentration independently of the plant scale. The chemical absorption can be applied if the plant scale is large and also the CO₂ concentration is low.     

Valuing regional geoscientific data acquisition programmes: addressing issues of quantification,uncertainty and risk

Geological surveys worldwide are involved with research in support of sustainable mineral resource development.The socio-economic benefits to be derived from these activities, however, continue to raise organisational and government sector questions. Fundamental questions include whether or not the resources committed are appropriate and in economic balance with the total benefits to be derived. Another question concerns the degree to which such services should be funded by the community at large. These questions in turn raise important issues regarding the role and cost of geological surveys, the impact of their services, and how they should maximise community benefit from their activities and expertise. To assess the value of geoscientific information,standard valuation processes need to be modified. This paper reports on a methodology designed to quantify the 'worth' of programmes upgrading regional geoscientific infrastructure. An interdisciplinary approach is used to measure the impact of geoscientific information using quantitative resource assessment, computer-based mineral potential modelling, statistical analysis and risk quantification to model decision-processes and assess the impact of additional data. These modelling stages are used to address problems of complexity,uncertainty and credibility in the valuation of geoscientific data. A case study demonstrates the application of the methodology to generate a dollar value for current regional data upgrade programmes in the Geological Survey of Queensland. The results obtained are used for strategic planning of future data acquisition programmes aimed at supporting mineral resource management and stimulating effective exploration activity.     

A cost-effective microbial slurry technology for rapid composting of municipal solid wastes in waste dump sites in India and its feasibility for use in Australia

This short article reports on commercial composting slurry now available in India. The slurry culture containing active decomposer bacteria and enzymes is spread on the surface of the garbage and inside the heaps in windrows constructed at waste dump sites. The microbes produce hydrolysing enzymes to break down the long chain complexes of the organic substrates. About 1 kg of slurry culture in the colloidal emulsion form mixed with 20 litres of water is sprayed on about 3 m of solid waste. For one tonne of waste 200 litres of slurry water are needed. The waste heaps are turned once in 7 to 10 days for proper aeration and the inoculant slurry is sprayed at each turning to enhance decomposition and to maintain the proper moisture level which is usually 45–55 percent. The process is exothermic and the windrows reach a temperature of 70°–75°C within 24–36 hours, killing many harmful pathogens and repelling all birds, stray animals, flies and mosquitos from the dump site. The entire process is completed within 4–6 weeks and as the decomposition is completed the temperature falls to normal. About 40–45 percent of the undecomposed matter is of recyclable materials, and of the rest about 25–30 percent requires safe disposal in adjacent land-fill sites. The problem of emission from tip gases and of leachate and discharge of effluents is greatly reduced. The foul odor of the tip also disappears within 2–3 days of sanitization. The compost produced is rich in sodium, potassium and phosphorous as well as certain trace elements, and contains active nitrogen fixing and phosphate solubulising bacteria.     

Real-time, high-resolution quantitative measurement of multiple soil gas emissions: selected ion flow tube mass spectrometry

A new technique is presented for the rapid, high-resolution identification and quantification of multiple trace gases above soils, at concentrations down to 0.01 microL L(-1) (10 ppb). The technique, selected ion flow tube mass spectrometry (SIFT-MS), utilizes chemical ionization reagent ions that react with trace gases but not with the major air components (N2, O2, Ar, CO2). This allows the real-time measurement of multiple trace gases without the need for preconcentration, trapping, or chromatographic separation. The technique is demonstrated by monitoring the emission of ammonia and nitric oxide, and the search for volatile organics, above containerized soil samples treated with synthetic cattle urine. In this model system, NH3 emissions peaked after 24 h at 2000 nmol m(-2) s(-1) and integrated to approximately 7% of the urea N applied, while NO emissions peaked about 25 d after urine addition at approximately 140 nmol m(-2) s(-1) and integrated to approximately 10% of the applied urea N. The monitoring of organics along with NH3 and NO was demonstrated in soils treated with synthetic urine, pyridine, and dimethylamine. No emission of volatile nitrogen organics from the urine treatments was observed at levels >0.01% of the applied nitrogen. The SIFT method allows the simultaneous in situ measurement of multiple gas components with a high spatial resolution of < 10 cm and time resolution <20 s. These capabilities allow, for example, identification of emission hotspots, and measurement of localized and rapid variations above agricultural and contaminated soils, as well as integrated emissions over longer periods.     

Losses of surface runoff, total solids, and nitrogen during bermudagrass establishment on levee embankments

Nutrient and sediment runoff from newly constructed levee embankments pose a threat to water quality during soft armor vegetation establishment. Research was initiated in 2008 and 2009 to evaluate the effect of bermudagrass ( L.) coverage and N source on nutrient and sediment runoff from levee embankments during establishment. Bermudagrass plots were seeded at 195.3 kg pure live seed ha and fertilized at 50 kg N ha using a water-soluble N source, urea or NH-NO, or slow-release N source, S-coated urea (SCU) or urea formaldehyde (UF), with controls unfertilized. Vegetative cover percentage, time until the onset of runoff, runoff volume, and total solids (TS), NO-N, and NH-N concentrations were measured from simulated and natural rainfall events for 70 d in 2008 and 56 d in 2009. Bermudagrass at 90% grass cover delayed the onset of runoff an additional 441 to 538 s and reduced runoff volumes 74 to 84% of that exhibited at 10% grass cover. Nitrogen fertilizers did not accelerate bermudagrass growth sufficiently, however, to reduce TS loading compared with unfertilized bermudagrass in either year of the study. The application of urea and SCU resulted in cumulative N losses of 2.45 and 3.13 kg ha compared with 1.59 kg ha from the unfertilized bermudagrass in 2008, and 1.73 kg ha from NH-NO vs. 0.24 kg ha from controls in 2009. Only UF increased bermudagrass establishment without increasing cumulative N losses compared with unfertilized bermudagrass. Therefore, the benefit of greater erosion and runoff resistance expected from N-accelerated vegetative growth did not occur but had the unintended consequence of higher N losses when water-soluble N and SCU fertilizers were applied.     

Physical, chemical, and mineralogical characteristics of a reservoir sediment delta (Lake Powell, U.S.A.) and implications for water quality during low water level

Lake Powell is a large reservoir in Utah and Arizona that has experienced large changes in water level during a recent drought. As a first step in assessing the connection between hydrologic and chemical changes at Lake Powell, we characterized the particle size and solid-phase bulk concentrations for 31 elements and 25 minerals in sediment from the inflow region and some shoreline locations by using laser diffractometry, X-ray fluorescence, elemental analysis, and X-ray diffraction Our results are consistent with previous results that show a negative correlation between particle size and concentrations of most elements and most minerals other than quartz and some feldspars. In our samples, however, solid-phase iron, rather than particle size or organic carbon, is the best predictor variable for the solid-phase concentrations of elements and minerals. Sediment characteristics vary on a scale of tens of kilometers, with fine sediment that is enriched in trace elementsnearer to the dam. These trends allow formulation of an algorithm for determining a water-level threshold below which sediment resuspension may alter water chemistry in a generic reservoir with a long and narrow sediment delta.     

不同凝乳酶在干酪成熟期的理化和生化特性研究

以当日鲜奶为原料,EZAL、MAOLL作为发酵剂,微生物酶、小牛皱胃酶、胃蛋酶、羔羊皱胃酶、木瓜蛋白酶和无花果蛋白酶作为凝乳酶生产硬质干酪,研究了不同凝乳酶在干酪成熟期的理化和生化特性.对这些干酪的理化和生化分析表明,在口感、风味、组织结构等方面,按品质依次为羔羊皱胃酶>小牛皱胃酶>微生物凝乳酶>猪胃蛋白酶>无花果蛋白酶>木瓜蛋白酶.     

Noise pollution monitoring during Diwali festival in Golden city Jaisalmer of Rajasthan, India

Noise is an important pollutant of environment causing various health hazards. In the present study, ambient noise levels were measured in two different areas within Jaisalmer city viz., commercial and residential area, on festive day and non-festive day (after) of Diwali. The results of noise level monitoring revealed the fact that due to higher amount of firecrackers on Diwali festival noise level was enhanced. The average equivalent noise level was increased from 61.94?dB to 72?dB (A) and 64.68?dB to 73.74?dB (A) on festive day, respectively, in selected residential and commercial areas, where noise was 30 and 13.44?% higher than standards of Central Pollution Control Board, New Delhi for residential and commercial areas, respectively.     

Trends of surface water quality of the Krishna River,India during the urbanization process

In the present study, Amaravati, the proposed city of India is considered to assess the impacts of urbanization on water quality of the Krishna River in the vicinity. Long-term surface water quality data of various parameters of Krishna River are obtained from Central Water Commission (CWC). Trends of various parameters are analyzed using a modified version of Mann-Kendall (M-K) test; bootstrapped M-K trend test with optional bias corrected pre-whitening and R programming are used affecting water quality prior to and at the commencement of urbanization. During the onset of urbanization, minimum BOD is decreased from 0.49 to 0.2 mg/L, while the maximum BOD is increased by 67.7%. Dissolved oxygen's (DO) minimum value is decreased by 29.33% while maximum DO value is decreased by 4.47% at the beginning of urbanization. During the process of urbanization, total coliform's minimum count is increased to 330 from 2 MPN/100 ml while the maximum count of total coliforms is increased to 16,000 from 2400 MPN/100 ml. Faecal coilform's minimum count is increased from 2 to 80 MPN/100 ml while maximum count is increased to 16,000 from 800 MPN/100 ml during urbanization. It is found that due to urbanization, pH, DO values exceed the allowable limit.