乙酸正丙酯在活性炭固体床上的动态吸附研究

乙酸正丙酯作为一种良好的有机溶剂,应用于许多行业,但其易挥发会对大气造成污染并危害人类健康。该文以商业活性炭作为吸附剂,在固体床吸附柱上连续吸附乙酸正丙酯,研究不同入口浓度的乙酸正丙酯在活性炭上动态吸附行为的影响以及活性炭再生性能。研究表明,活性炭具有较高的固气分配系数,随着入口浓度的增大(4.40～21.96 mg/L),平衡吸附量逐渐变大(388.67～513.17mg/g),传质区高度增加,穿透时间缩短,动态吸附容量变大。采用2种穿透曲线模型(Thomas和Yoon-Nelson模型)和4种动力学模型(伪一级、伪二级、Elocivh和Bangham模型)对实验数据进行拟合分析。结果表明,Thomas和Bangham模型拟合效果较好(R20.99)。通过模型拟合能够较好预测不同入口浓度的乙酸正丙酯在活性炭上的动态吸附容量,具有一定实际意义。     

萘在炭质吸附剂上的静态吸附机理

通过分析考察试验吸附等温线与Langmuir,BET和Freundlich模型的拟合结果,以及吸附剂的结构参数(比表面积、总孔容积、平均孔径),对萘(Nap)在3种活性炭吸附剂上的静态吸附行为进行了研究.结果表明:3种活性炭吸附剂对萘均表现出良好的吸附能力(吸附量最高可达0.231 1 g/g),改性后活性炭颗粒吸附性能要明显优于原活性炭;萘在活性炭颗粒(AC-a,AC-c)和活性炭粉末(AC-b)上的吸附行为存在差异,在活性炭颗粒上表现为单分子层吸附的过程,而在具有突出比表面积的活性炭粉末上,吸附过程表现出多分子层吸附的特征.Langmuir和BET模型可以分别对萘在活性炭颗粒和粉末上的静态吸附行为进行合理的预测.      

活性炭吸附乙酸乙酯的动态吸附和动力学研究

该研究以商业活性炭为固定床填充剂,研究了活性炭固定床对乙酸乙酯的吸附脱附行为。使用的商业活性炭具有极高的比表面积,达到1 099.74 m2/g,对乙酸乙酯的最大吸附量达到443.7 mg/g。对活性炭吸附乙酸乙酯的实验数据进行了动态吸附模型拟合和动力学拟合,包括Boltzmann和Yoon-Nelson 2种动态吸附模型,伪一级动力学、伪二级动力学、Banham吸附率方程和Elovich方程4种动力学模型。结果表明Boltzmann模型和Banham吸附率方程具有更好的拟合效果,说明活性炭固定床的传质阻力小,传质效率高,并且发现通过Banham吸附率方程计算出来的的最大吸附量与实际最大吸附量高度吻合,可以利用该模型预测其他VOCs的吸附曲线,具有一定实际意义。     

高分子固体废物基活性炭对有机染料的吸附解吸行为研究

分别以3种高分子固体废物,即轮胎橡胶、聚氯乙烯(PVC)和聚对苯二甲酸乙二酯(PET)为原料,利用KOH活化法制备高比表面积活性炭.通过吸附实验研究了活性炭对2种有机染料(亚甲基蓝和甲基橙)的吸附、解吸行为,同时探讨了溶液pH值、离子强度和表面活性剂对吸附的影响.结果表明,PVC和PET基活性炭比表面积分别为2 666和2 831 m2.g-1,中孔容积分别为1.06和1.30 cm3.g-1,15 min内对亚甲基蓝和甲基橙的去除率分别高达98.5%和97.0%、99.5%和95.0%,且Langmuir模型拟合的染料最大吸附量均超过2 mmol.g-1,显著高于商业活性炭F400.Langmuir模型比Freundlich模型能更好地描述2种染料的吸附行为,说明吸附以表面单层覆盖为主.溶液pH值、离子强度和表面活性剂对染料吸附均有较大影响.制备的高分子基活性炭对亚甲基蓝的吸附强于甲基橙,2种染料均不容易发生解吸.实验结果可为高分子固体废物的资源化利用、制备经济高效的碳质吸附材料提供科学依据.     

玉米秸秆黄原酸盐对铅离子的动态吸附特征

玉米秸秆黄原酸盐是一种新型的重金属吸附材料.为了揭示玉米秸秆黄原酸盐对溶液中铅离子的动态吸附特征,本文通过柱体穿透吸附模拟实验方法,研究了玉米秸秆黄原酸对流体中铅离子的吸附穿透曲线、吸附效率及水体流速、初始浓度、填柱高度等因素对其吸附特性的影响,并采用The Thomas、The Bohart-Adams、The Wolborskal和The Yoon-Nelson等模型进行动力学拟合.结果表明,流速、初始浓度、填柱高度等因素对玉米秸秆黄原酸盐吸附铅离子的穿透曲线都有明显影响,Thomas模型和Yoon-Nelson模型能较好反映吸附过程特征.实验表明,玉米秸秆黄原酸盐对铅离子的吸附量为175 mg·g~(-1),吸附后的玉米秸秆黄原酸盐残渣体性能稳定.     

PDMS基涂层活性炭对甲苯、苯和丙酮吸附研究

活性炭疏水性改性是提高其对含水VOCs选择性吸附的重要手段,然而这种改性方法对活性炭吸附不同VOCs的效果研究较少.采用聚二甲基硅氧烷(polydimethylsiloxane,PDMS)对活性炭进行改性处理,并利用BET、Boehm滴定等方法对活性炭进行表征.采用动态吸附法,利用Yoon-Neslon吸附理论模型研究了不同相对湿度条件下,PDMS改性活性炭对VOCs(甲苯、苯、丙酮)吸附穿透曲线、饱和吸附量的影响及关键影响因素.结果表明:PDMS改性活性炭BET比表面积、微孔容积和表面酸碱官能团含量均有减少;经PDMS改性后,活性炭表面疏水性增大.动态吸附实验结果表明:PDMS改性前后活性炭吸附甲苯、苯、丙酮穿透曲线均符合Y-N模型;随着相对湿度增大,未经改性的活性炭(Bare-AC)对甲苯、苯和丙酮吸附速率降低、平衡吸附量减少,PDMS改性活性炭对甲苯、苯分子吸附速率和选择吸附能力提高,其中PDMS改性的活性炭(PDMS/AC-250)对甲苯、苯吸附量为相同条件下Bare-AC的1.86(甲苯)、1.92(苯)倍,但对丙酮分子提高不明显;结合表征结果分析,PDMS改性活性炭对VOCs分子吸附主要依靠化学吸附,同时与VOCs分子极性有关.     

负载Cu改性活性炭吸附VOCs性能的研究

采用浸渍焙烧法对活性炭进行铜负载改性,并用于甲苯、乙酸乙酯及甲苯-乙酸乙酯二元混合气体的吸附。结果表明:醋酸铜负载量1.5%时活性炭吸附性能最好,对于单组分气体吸附,改性活性炭对甲苯和乙酸乙酯的吸附量较未改性前分别提高了29.7%和21.3%,穿透时间分别延迟了19.3%、18.6%;对于二元混合气体吸附,改性后活性炭较未改性活性炭对甲苯和乙酸乙酯的吸附量分别提高了19.4%和33.0%。采用BET、SEM、FTIR、XRD等分析表明,铜负载改性后的活性炭比表面积变大、总孔容变大,且铜与VOC的络合作用是改性后吸附量提高的主要原因。     

用活性炭吸附法脱除氮氧化物的研究

应用活性炭进行了氮氧化物（Nox）的吸附试验研究。讨论了活性炭种类、填充质量、反应温度、氧气含量、活性炭的预处理等因素对NOx吸附效果的影响。研究结果表明：不同种活性填料对于吸附性能影响显著。吸附剂的质量、氧气含量增加，穿透时间变长；气体中NOx的体积百分比变大，穿透时间先增长后下降，在NOx的体积百分比约为25％时吸附效果最好；温度升高，穿透时间变小；预处理能提高穿透时间。     

粉末活性炭粒径对水中菲吸附动力学的影响效应研究

以菲为目标污染物,研究了粉末活性炭(PAC)在微尺度(1～ 100.Μm)下的粒径效应对多环芳烃吸附性能的影响.实验中按照中值粒径将研磨后得到的粉末活性炭划分为:PAC-1 (19 μm)、PAC-2(46μm)、PAC-3(76 μm).通过比表面积及孔隙度自动分析仪、原位拉曼光谱、扫描电镜等手段对PAC物化性质进行表征,发现粒径减小使PAC的BET比表面积和总孔容增加了10％ ～20％左右,而对PAC表面化学性质的影响较小.PAC的粒径分布对其吸附性能有显著影响,这种影响主要体现为吸附速率成倍的增加,其次是吸附容量有30％ ～36％的增幅.分别用3种动力学模型对吸附过程进行拟合,结果表明,伪二级动力学方程的拟合程度最高,PAC-1有最大的吸附速率常数k,并且随着粒径的减小,k值逐渐增大.     

颗粒活性炭对水中邻苯二甲酸二甲酯的吸附特性

研究了颗粒活性炭(GAC)对水中邻苯二甲酸二甲酯(DMP)的静态与动态吸附特性.结果表明,Freundlich和Langmuir等温线模型可以较好的拟合GAC对DMP的吸附.GAC对DMP的吸附容量较大,溶液初始浓度为200mg/L时,GAC对DMP的动态和最大静态吸附容量分别为484.60,450.89mg/g.考察了不同流速条件下(0.65～4.00mL/min)GAC吸附DMP的穿透特性,Yoon-Nelson模型能很好地拟合DMP在GAC柱中的穿透曲线,根据试验数据和Yoon-Nelson模型计算出穿透参数K′、T和穿透点t1以及平衡点t2.在建立了进水流量与Yoon-Nelson穿透模型的参数之间的关系基础上,得到了活性炭柱出水浓度与进水流量和穿透时间之间的动态关系模型.     

碱改性活性炭表面特征及其吸附甲烷的研究

采用不同浓度的氢氧化钠对椰壳活性炭进行表面改性.BET和SEM分析改性前后活性炭的表面结构,Boehm滴定和SEM/EDS方法测定活性炭表面元素及含氧基团.研究改性活性炭对甲烷的吸附性能和吸附行为.结果表明,经氢氧化钠改性处理后,活性炭孔径变化不明显,表面含氧基团显著减少;当氢氧化钠的浓度>3.3 mol·L-1时,活性炭的比表面积和孔容大于未处理的活性炭,并且随碱的浓度增加而增大.与改性前的活性炭相比,甲烷在碱改性活性炭上的吸附量提高了24%.增加活性炭的比表面积和孔容,减少表面的含氧基团有利于甲烷的吸附.甲烷的吸附行为符合Langmuir等温吸附式,吸附常数为163.7 m3·mg-1.     

Adsorptive removal of hydrophobic organic compounds by carbonaceous adsorbents: A comparative study of waste-polymer-based, coal-based activated carbon, and carbon nanotubes

Adsorption of the hydrophobic organic compounds (HOCs) trichloroethylene (TCE), 1,3-dichlorobenzene (DCB), 1,3-dinitrobenzene (DNB) and γ-hexachlorocyclohexane (HCH) on five different carbonaceous materials was compared. The adsorbents included three polymer-based activated carbons, one coal-based activated carbon (F400) and multiwalled carbon nanotubes (MWNT). The polymerbased activated carbons were prepared using KOH activation from waste polymers: polyvinyl chloride (PVC), polyethyleneterephthalate (PET) and tire rubber (TR). Compared with F400 and MWNT, activated carbons derived from PVC and PET exhibited fast adsorption kinetics and high adsorption capacity toward the HOCs, attributed to their extremely large hydrophobic surface area (2700 m²/g) and highly mesoporous structures. Adsorption of small-sized TCE was stronger on the tire-rubber-based carbon and F400 resulting from the pore-filling effect. In contrast, due to the molecular sieving effect, their adsorption on HCH was lower. MWNT exhibited the lowest adsorption capacity toward HOCs because of its low surface area and characteristic of aggregating in aqueous solution.     

Removal of bromate ion using powdered activated carbon

Bromate ion (BrO 3) removal from drinking water by powdered activated carbons (PAC S) in bath mode was evaluated under various operational conditions.Six kinds of PACs,including wood-based carbon,fruit-based carbon,coal-based carbon,and these three carbons thermally deoxidized in a nitrogen atmosphere,were selected to investigate their capacity on BrO 3 removal.With the highest zeta potential value and being richly mesoporous,coal-based carbon had a high and an excellent BrO 3 adsorption efficiency.The removal content of BrO 3 by per gram of coal-based carbon was 0.45 mg within 5 hr in 100 μg/L bromate solution.The surface characteristics of PACs and bromide formation revealed that both physical and chemical PACs properties simultaneously affected the adsorptionreduction process.Under acidic conditions,PAC S possessed high zeta value and adequate basic groups and exhibited neutral or positive charges,promoting BrO 3 adsorption-reduction on the carbon surface.Interestingly,the PAC S thermally deoxidized in N 2 atmosphere optimized their properties,e.g.increasing their zeta values and decreasing the oxygen content which accelerated the BrO 3 removal rate.The maximum adsorption capacity of fruit-based carbon was the highest among all tested carbons (99.6 mg/g),possibly due to its highest pore volume.Remarkably,the thermal regeneration of PACs in N 2 atmosphere could completely recover the adsorption capacity of PACs.The kinetic data obtained from carbons was analyzed using pseudo second-order and intraparticle diffusion models,with results showing that the intraparticle diffusion was the more applicable model to describe adsorption of BrO 3 onto PACs.     

Breakthrough CO2 adsorption in bio-based activated carbons

In this work, the effects of different methods of activation on CO₂ adsorption performance of activated carbon were studied. Activated carbons were prepared from biochar, obtained from fast pyrolysis of white wood, using three different activation methods of steam activation, CO₂ activation and Potassium hydroxide (KOH) activation. CO₂ adsorption behavior of the produced activated carbons was studied in a fixed-bed reactor set-up at atmospheric pressure, temperature range of 25–65°C and inlet CO₂ concentration range of 10–30 mol% in He to determine the effects of the surface area, porosity and surface chemistry on adsorption capacity of the samples. Characterization of the micropore and mesopore texture was carried out using N₂ and CO₂ adsorption at 77 and 273 K, respectively. Central composite design was used to evaluate the combined effects of temperature and concentration of CO₂ on the adsorption behavior of the adsorbents. The KOH activated carbon with a total micropore volume of 0.62 cm³/g and surface area of 1400 m²/g had the highest CO₂ adsorption capacity of 1.8 mol/kg due to its microporous structure and high surface area under the optimized experimental conditions of 30 mol% CO₂ and 25°C. The performance of the adsorbents in multi-cyclic adsorption process was also assessed and the adsorption capacity of KOH and CO₂ activated carbons remained remarkably stable after 50 cycles with low temperature (160°C) regeneration.     

Behaviors and kinetics of toluene adsorption‐desorption on activated carbons with varying pore structure

This work was undertaken to investigate the behaviors and kinetics of toluene adsorption and desorption on activated carbons with varying pore structure. Five kinds of activated carbon from different raw materials were selected. Adsorption isotherms and breakthrough curves for toluene were measured. Langmuir and Freundlich equations were fitted to the equilibrium data, and the Freundlich equation was more suitable for simulating toluene adsorption. The process consisted of monolayer, multilayer and partial active site adsorption types. The effect of the pore structure of the activated carbons on toluene adsorption capacity was investigated. The quasi-first-order model was more suitable for describing the process than the quasi-second-order model. The adsorption data was also modeled by the internal particle diffusion model and it was found that the adsorption process could be divided into three stages. In the external surface adsorption process, the rate depended on the specific surface area. During the particle diffusion stage, pore structure and volume were the main factors affecting adsorption rate. In the final equilibrium stage, the rate was determined by the ratio of meso-and macro-pores to total pore volume. The rate over the whole adsorption process was dominated by the toluene concentration. The desorption behavior of toluene on activated carbons was investigated,and the process was divided into heat and mass transfer parts corresponding to emission and diffusion mechanisms, respectively. Physical adsorption played the main role during the adsorption process.     

改性活性炭对水溶液中双酚-A的吸附研究

采用HNO3、NaOH及高温N2对商用炭WV A1100进行表面改性处理,并利用BET、XPS、pH.及Boehm方法对活性炭进行物化表征.结果表明,HNO3改性明显降低了W20的比表面积,增加了其表面酸性含氧官能团数量,使等电点(pHpae)由4.95降至1.50;高温N2和NaOH改性处理后炭表面化学性质变化与HNO3氧化基本相反,pHp.升至近中性,其中高温N2处理降低了43.81%的表面积.另外,活性炭对双酚-A(BPA)的吸附实验结果表明,吸附体系中溶解氧的存在不会促使BPA在W20表面发生酚氧自由基氧化耦合,并且原炭W20、高温N2和NaOH改性处理后炭对BPA的吸附等温线结果满足Langmiur模型,而HNO3改性炭的吸附行为更符合Freundlich模型,其中高温N2改性炭表现出最好的吸附BPA能力,饱和吸附量值达到了526.32mg/g,是能力最差炭(HNO3改性)的3倍,结合表征结果分析得出,在吸附体系中炭表面的憎水性和静电荷密度,是控制分子态BPA吸附过程的主要因素,即吸附主要遵循π-π理论.     

碘化活性炭吸附和预富集水体汞的方法

化学处理活性炭对汞等重金属离子具有良好的吸附特性。通过一系列测试获得了碘化和氯化活性炭预富集水体汞的优化方案。对实验室配制汞标准样品的测试表明,碘化和氯化活性炭对汞具有良好的吸附特性,而采样管的内径、活性炭的填充量以及过滤流速均影响活性炭预富集水体汞的效率。采用600mg的碘化活性炭采样管(内径:0.35cm),在水体过滤流速为10r/min(7mL/min)~25r/min(17mL/min)的条件下,碘化活性炭对水体汞的吸附效率可达到95%以上。增加流速和采样管内径以及减少活性炭填充量均会降低活性炭对水体汞的吸附效率。同时进一步测试了碘化活性炭对高汞(万山汞矿区渗滤水,含量范围:37.68~321.57ng/L)和低汞(贵阳市降水,含量范围:2.76~9.98ng/L)等天然水体汞的预富集效率,其预富集效率的平均值分别为96.74%(n=8)和96.09%(n=8)。该研究为采用化学处理活性炭技术预富集天然水体汞以及开展水体汞同位素测试提供了一种全新方法。     

污泥基活性炭吸附空气中甲醛的研究

以城市污水处理厂脱水污泥为原料,氯化锌为活化剂制备污泥基活性炭,采用BET比表面积测试、扫描电镜(SEM)、傅里叶红外光谱(FTIR)等方法研究其理化性能,利用动态吸附实验系统和蒸馏装置,将污泥基活性炭与选定的商业活性炭进行了甲醛吸附性能对比,并利用热重分析法研究了甲醛在各活性炭上的脱附情况.结果表明,污泥基活性炭对空气中浓度分别为498,0.41mg/m3的甲醛均有很好的吸附效果,吸附量分别可达74.27,7.62mg/g,最大去除率分别为83.72%和89.56%,其吸附性能与选定的商业活性炭相当,特别是在处理浓度为0.41mg/m3甲醛时超过选定的商业活性炭.该污泥基活性炭BET比表面积为509.88m2/g,氮吸附等温线属于BDDT分类中的I-B型,表明其具有大量的超微孔和极微孔,更适用于低浓度甲醛的吸附.FTIR分析表明其表面含有各种含氮基团,特别是-NH2的存在,可能形成化学吸附中心,但从吸附甲醛后各活性炭的微商热重分析(DTG)曲线可以看出,各甲醛在活性炭上的吸附主要为物理吸附.     

Insights into properties of activated carbons prepared from different raw precursors by pyrophosphoric acid activation

Low-cost activated carbons (ACs) were prepared from four kinds of solid wastes: petroleum coke, Enteromorpha prolifera, lignin from papermaking black liquid and hair, by pyrophosphoric acid (H₄P₂O₇) activation. Thermo-gravimetric analysis of the pyrolysis of H₄P₂O₇-precursor mixtures implied that H₄P₂O₇ had different influences on the pyrolysis behavior of the four raw materials. N₂ adsorption/desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy and adsorption capacities for dyes were used to characterize the prepared activated carbons. AC derived from E. prolifera exhibited the highest surface area (1094 m²/g) and maximum monolayer adsorption capacity for malachite green (1250 mg/g). Kinetic studies showed that the experimental data were in agreement with the pseudo-second-order model. The adsorption isotherms were well described by the Langmuir isotherm model, indicating the adsorption of dye onto the ACs proceeded by monolayers.