Characterization of different road dusts in opencast coal mining areas of India

Dust from haul and transport roads are the major source of air pollution in opencast coal mining areas. Dust generated during mining operations pollutes air which causes different health problems. Various available techniques are implemented in the field to minimize and control dust in mining areas. However, they are not very effective because dust deposited on road surfaces are not removed by these techniques. For effective control of dust in opencast mining areas, it has to be regularly collected from road surfaces and may be converted into solid form, and subsequently can be used as a domestic fuel considering its physicochemical properties. The present paper describes a comparative study of qualitative and quantitative aspects of road dust samples of four coalfields of India. The pH of the dust was found to be in the range of 5.1–7.7. Moisture, ash, volatile matter, fixed carbon, water-holding capacity, bulk density, and specific gravity of dust samples were found to be in the range of 0.5–3.0%, 45–76%, 12.6–20.0%, 10.2–45.3%, 21.17–31.71%, 1.15–1.70, and 1.73–2.30 g cm⁻³, respectively. Observing the overall generation and characteristics of coal dust, it is suggested that coal dust from haul and transport roads of mining areas can be effectively collected and used as domestic fuel.     

Bioassessment in A Harsh Environment: A Comparison of Macroinvertebrate Assemblages at Reference and Assessment Sites in An Australian Inland River System

The Lachlan River system of inland New South Wales, which extends into semi-arid areas, is prone to natural extremes of climate and water quality and has been almost entirely modified since European settlement in Australia. We used this system as a proving ground for the mainly qualitative bioassessment metrics for river macroinvertebrates that are used widely in Australia – the EPT (Ephemeroptera, Plecoptera and Trichoptera) index, the SIGNAL (Stream Invertebrate Grade Number Average Level) biotic index and the AUSRIVAS O/E (Australian River Assessment System Observed over Expected) index – plus a recently developed qualitative index, the observed proportion of potential taxa (OPP). We tested these metrics on their ability to discriminate between sites judged to be less disturbed by human activities (reference sites) and sites selected by a semi-random process and therefore expected to have a higher average level of human disturbance (assessment sites). All metrics except the AUSRIVAS O/E index differed significantly between the two types of sites at higher altitudes, with SIGNAL showing the greatest discrimination. Assessment at these altitudes was more effective if based on composite data from multiple mesohabitats rather than data from single mesohabitats. No metric differentiated the two types of sites in the more arid, lowland, floodplain region of the river system. We suggest that Australia relies too heavily on bioassessment concepts developed to assess water pollution in well-watered regions of the Northern Hemisphere. Effective assessment of human impacts on macroinvertebrates in the rivers of inland Australia requires a better understanding of the roles of flow regimes, including flood and drought sequences, and of microhabitat structure and invasive alien species. Quantitative approaches may also be required.     

Integration of Case Studies on Global Change by Means of Qualitative Differential Equations

We present a novel methodology to integrate qualitative knowledge from different case studies on Global Change related issues into a single framework. The method is based on the concept of qualitative differential equations (QDEs) which represents a mathematically well-defined approach to investigate classes of ordinary differential equations (ODEs) used in conventional modeling exercises. These classes are defined by common qualitative features, e.g., monotonicity, signs, etc. Using the QSIM-algorithm it is possible to derive the set of possible solutions of all ODEs in the class. By this one can formulate a common, qualitatively specified cause–effect scheme valid for all case studies. The scheme is validated by testing it against the actually observed histories in the study regions with respect to their reconstruction by the corresponding QDE. The method is outlined theoretically and exemplary applied to the problem of land-use changes due to smallholder agriculture in developing countries. It is shown that the seven case-studies used can be described by a single cause–effect scheme which thus constitutes a pattern of Global Change. As a generally valid prerequisite for sustainability of this kind of land-use the presence of wage labor is shown to represent a decisive factor. This revised version was published online in July 2006 with corrections to the Cover Date.     

The role of environmental and socio-demographic indicators in the analysis of land use changes in a protected area of the Natura 2000 Network: the case study of Lake Trasimeno,Umbria, Central Italy

This article sets out to analyse how and to what degree land use is linked to the physical characteristics of the territory itself, and the way in which changes in land use are determined by agricultural and socio-demographic dynamics. The study was conducted within the territorial boundaries of five municipalities surrounding Lake Trasimeno and refers to the periods 1977–2000 for land use and 1971–2001 for socio-demography data. The use of environmental, social, economic and agricultural indicators demonstrates how a mix of various indicators are useful for monitoring the changes which took place. It also shows the powerful influence that socio-demographic factors exert upon land use and landscape change.     

Assessment of a General Finite Line Source Model and CALINE4 for Vehicular Pollution Prediction in Ireland

A comparative evaluation of two Gaussian-based line source models namely, California line source dispersion model version 4 and the general finite line source model, is presented. The concentrations predicted by these models are compared with background-corrected ambient concentrations measured at three different distances from a motorway and performance of both models assessed in the context of integrated transport–environment modelling for regulatory purposes.     

Assessment of water pollution in different bleaching based paper manufacturing and textile dyeing industries in India

Paper industries using different raw materials such as hard wood, bamboo, baggase, rice-straw and waste papers and bleaching chemicals like chlorine, hypochlorite, chlorine dioxide, hydrogen peroxide, sulphite and oxygen were studied to estimate organic pollution load and Adsorbable Organic Halides (AOX) per ton of production. The hard wood based paper industries generate higher Chemical Oxygen Demand (COD) loads (105–182 kg t⁻¹) and Biochemical Oxygen Demand (BOD) loads (32.0–72 kg t⁻¹) compared to the agro and waste paper based industrial effluents. The bleaching sequences such as C–EP–H–H, C–E–H–H, C–E–Do–D1 and O–Do–EOP–D1 are adopted in the paper industries and the molecular elemental chlorine free bleaching sequence discharges low AOX in the effluent. The range of AOX concentration in the final effluent from the paper industries was 0.08–0.99 kg t⁻¹ of production. Water consumption was in the range of 100–130 m³ t⁻¹ of paper production for wood based industries and 30–50 m³ for the waste paper based industries. Paper machine effluents are partially recycled after treatment and pulp mill black liquor are subject to chemical recovery after evaporation to reduce the water consumption and the total pollution loads. Hypochlorite bleaching units of textile bleaching processes generate more AOX (17.2–18.3 mg l⁻¹) and are consuming more water (45–80 l kg⁻¹) whereas alkali peroxide bleaching hardly generates the AOX in the effluents and water consumption was also comparatively less (40 l kg⁻¹ of yarn/cloth).     

Determination of Heavy Metals in Water from Boreholes in Dumasi in the Wassa West District of Western Region of Republic of Ghana

Concentrations of heavy metals in the borehole at Dumasi in the Wassa West District of the Republic of Ghana have been measured in this study. The concentrations of the following metals in the ground water from Dumasi borehole are: Iron (Fe) – 7.52 ppm, Manganese (Mn) – 1.11 ppm, Arsenic (As) – 4.52 ppm, Chromium (Cr) – 0.026 ppm, Cobalt (Co) – 0.01 ppm, Zinc (Zn) – 0.007 ppm, Cadmium (Cd) – 0.002 ppm and Lead (Pb) – 0.005 ppm. The results of the study show that resident adults and children who use water from the boreholes are at serious risk from exposure to health hazards associated with exposure to the above metals in the boreholes in Dumasi. If the results of this study are applied to other mining communities, which lie on the Birimian and Tarkwaian rock system, then the residents are at serious risk from exposure to toxic metals from drinking water from the boreholes dug for them by mining companies operating in their communities.     

Analysis of Polycyclic Aromatic Hydrocarbons in Street Soil Dust in Kumasi Metropolis of Ghana

Concentrations of polycyclic aromatic hydrocarbons (PAHs) in street soil dust from streets in Kumasi Metropolis in the Ashanti Region of the Republic of Ghana have been measured in this study. The concentrations of the various types of PAHs identified in this study are as follows: Naphthalene (m/e 128) – 41,700 μg/kg, Acenaphthylene (m/e 152) – 99,300 μg/kg, Acenaphthene (m/e 154) – 111,200 μg/kg, Fluorene (m/e 166) – 8,900 μg/kg, Carbazole (m/e 167) – 3,500 μg/kg, phenathrene (m/e 178) – 12,900 μg/kg, Anthracene (m/e 178) – 5,400 μg/kg, Fluoranthene (m/e 202) – 16,200 μg/kg, Pyrene (m/e 202) – 15,000 μg/kg, Benzo[a]anthracene (m/e 228) – 13,800 μg/kg, Chrysene (m/e 228) – 33,600 μg/kg, Benzo[k]fluoranthene (m/e 252) – 45,700 μg/kg, Benzo[a]pyrene (m/e 252) – 27,900 μg/kg, Perylene (m/e 252) – 57,200 μg/kg and Benzo[g, h, i]perylene (m/e 276) – 47,000 μg/kg. The results of the study shows that road users, like resident living in buildings within these areas, those engaged in commercial activities like hawking, and the general public are at risk of exposure to the toxic effects of the various types of PAHs from the exhaust of vehicles into the environment. According to these results, there is the potential for exposure to high levels of PAHs for road users and those living in urban environments or along highways.     

Distribution of heavy metals in surface water of Ranipet industrial area in Tamil Nadu, India

Ranipet industrial area is about 120 km from Chennai on Chennai-Bangalore highway and is a chronic polluted area identified by Central Pollution Control Board of India. It is one of the biggest exporting centers of tanned leather in India. The total number of industries located in and around Ranipet town are 240 tanneries along with ceramic, refractory, boiler auxiliaries plant, and chromium chemicals. Studies were carried out to find out the contamination of surface water bodies due to industrial effluents. The results reveal that the surface water in the area is highly contaminated showing very high concentrations of some of the heavy/toxic metals like Cadmium ranging from 0.2 to 401.4 μg/l (average of 51.1 μg/l), Chromium 2.4–1,308.6 (average of 247.2 μg/l), Copper 2.1–535.5 μg/l (average of 95.5 μg/l), Nickel 1.6–147.0 μg/l (average of 36.7 μg/l), Lead 6.4–2,034.4 μg/l (average of 467.8 μg/l) and Zinc 20.8–12,718.0 μg/l (average of 3,760.4 μg/l). The concentration levels of these metals are much above the permissible limits in surface water and are health hazards especially for the people working in the tannery industries. It was observed that the people in the area are seriously affected and suffering from occupational diseases such as asthma, chromium ulcers and skin diseases. Distribution of metals, their contents at different locations, and their effects on human health are discussed in this paper.     

Impact of untreated wastewater irrigation on soils and crops in Shiraz suburban area, SW Iran

In this study an assessment is made of the negative impacts of wastewater irrigation on soils and crops sampled along the Khoshk River channel in suburban area of Shiraz City, SW Iran. For this purpose, samples of soil profiles (0–60 cm in depth) and crops were collected from two wastewater irrigated sites and a tube well-irrigated (control) site. Total concentrations of the five heavy metals (Ni, Pb, Cd, Zn and Cr) and their phytoavailable contents were determined. The Pollution Load Indexes (PLIs) and Contamination Factors (CFs) for soils and Hazard quotients (ΣHQ) for some vegetables were also calculated. The results showed the use of untreated wastewater has caused the following changes as compared to control site: (1) a 20–30% increase in organic matter content of soil; (2) increase in pH by 2–3 units; (3) significant concentration increase in Ex-Ca especially in top layers of soil resulting in high CEC; (4) build up of heavy metals (notably Pb and Ni) in topsoil above Maximum Permissible Limits (MPLs) indicating a moderate contamination (PLI > 1, CF > 2.5); (5) contamination of some vegetables (spinach and lettuce) with Cd due to its high phytoavailability in topsoil causing a HQ > 1; (6) excessive accumulation of Ni and Pb in wheat due to continual addition of heavy metals through long-term wastewater application. The study concludes that strict protection measures, stringent guidelines and an integrated system for the treatment and recycling of wastewater are needed to minimize the negative impacts of wastewater irrigation in the study area.     

Mobility of Different Phosphorus Pools in the Sediment of Lake Dianchi during Cyanobacterial Blooms

By the method of P fractionation, we examined sedimentary P fractions in Lake Dianchi before and during cyanobacterial blooms, namely in April 2004 and August 2004, respectively. In this study, the whole lake is divided into four areas to discuss P fractions in sediment and the relationship between them and water quality or the nutrient status. The results show that where the water body was much more eutrophic (higher levels of total phosphorus, total nitrogen, chlorophyll and trophic status index) in Lake Dianchi, there can be more potentially available phosphorus (BD–P and NaOH–P) and less no available phosphorus (HCl–P and residual P) in the corresponding sediments. Statistical analysis and statistical plots are used to compare the distribution of every P fraction during cyanobacterial blooms with that before cyanobacterial blooms, and the results indicate that the different P fractions had the different mobility. HCl–P and residual P were relatively stable, while NaOH–P, BD–P and NH4Cl–P were more mobile. BD–P can intensively be released from sediment to water and consequently promote cyanobacterial blooms, and at the same time the NaOH–P concentration increased in sediment, which can result from that BD–P released can be partly immobilized to NaOH–P. During cyanobacterial blooms BD–P can be as a source, but NaOH–P as a sink. Besides, total phosphorus in sediment had no significant differences between two samplings.     

The determination of ambient formaldehyde using a dual coil system and an assessment of dominant factors that influence its abundance in Korea

An enhanced dual coil 2,4-dinitrophenylhydrazine (DNPH) derivatization method (dual coil/DNPH) allowed the quantitative determination of formaldehyde (HCHO) in ambient air. In this method, traceable HCHO was collected using a coil sampler connected in series and lacking a long sampling tube. It was then analyzed using liquid chromatography followed by UV detection of the DNPH derivatives. The method is based on the reaction of formaldehyde with DNPH to produce 2,4-dinitrophenylhydrazone. The detection limits (3σ) were 0.10–0.40 ppbv with a precision ranging from 0.84 to 4.09% RSD. The results of dual coil/DNPH and conventional DNPH cartridge methods were generally well correlated: HCHO (dual coil/DNPH) = 0.97 (±0.13) vs. HCHO (DNPH Cartridge) + 0.33 (±0.33), r = 0.82. The dual coil/DNPH method was used to measure gaseous HCHO in the atmosphere of Metropolitan Seoul during the summer 2000 and 2001, and in Gwangju during the fall of 2001 and 2002. The daytime mean concentration of HCHO was 4.52 (±5.69) and 3.21 (±1.27) ppbv in Metropolitan Seoul for 10–12 August 2000 and 29–31 May 2001, respectively, and 1.73 (±0.98), 3.04 (±2.25), 2.70 (±1.70), and 2.01 (±2.28) ppbv in Gwangju City during 22–27 September 2001, 17–24 October 2001, 9–13 October 2002, and 28 October to 2 November 2002, respectively. The HCHO in Seoul from 10–12 August 2000 was mainly the result of photochemical processes, while direct emissions from vehicles and long-range transport of air from China contributed during 29–31 May 2001. During 22–27 September 2001, 17–24 October 2001, and 9–13 October 2002 in Gwangju, the HCHO came primarily from photochemical processes, although some air affected by biomass burning admixed in the late afternoon. The increase in the HCHO concentration on 20 October 2001 and from 28 October to 2 November 2002 was attributed mainly to direct emissions from biomass burning in farmland near the measurement site.     

Extended Analytical Turbulent Diffusion Model for Particle Dispersion and Deposition in a Horizontal Pipe: Comparison with CFD Simulation

A 2D analytical turbulent diffusion model for particle dispersion and deposition at different heights along the pipe flow and circumferential deposition has been developed. This liquid–solid turbulent diffusion model presented in this paper has emanated from an existing gas–liquid turbulent diffusion model. This model can be used as a handy tool for quick estimation one and two-dimensional deposition fluxes of particles in water distribution networks. A comprehensive 3D numerical investigation has been carried out using multiphase mixture model available in “Fluent 6.2” to verify the above analytical model. Different particles sizes and densities were used for 3D numerical investigations. The deposition was studied as a function of particle diameter, density, and fluid velocity. The deposition of particles, along the periphery of the pipe wall and at different depths, was investigated. Both the models findings matched with qualitative phenomena such as deposition of heavier particles at the bottom of the pipe wall were higher at lower velocities and lower at higher velocities. The lighter particles were found mostly suspended with homogeneous distribution. Smaller particles were also suspended with marginal higher concentration near the bottom of the pipe wall. This marginal higher concentration of the smaller particles was found to be slightly pronounced for lower velocity. These analogies of particles are well discussed with the ratio between free-flight velocity and the gravitational settling velocity. Extended analytical model results were compared with the 3D computational fluid dynamics simulation results. Discrepancies in the model results were discussed.     

Trace metal concentrations in suspended particles, sediments and clams (Ruditapes philippinarum) from Jiaozhou Bay of China

Suspended particulate matter (SPM), sediments and clams were collected at three sites in Jiaozhou Bay to assess the magnitude of trace metal pollution in the area. Metal concentrations in SPM (Cu: 40.11–203; Zn: 118–447; Pb: 50.1–132; Cd: 0.55–4.39; Cr: 147.6–288; Mn: 762−1670 μg/g), sediments (Cu: 17.64–34.26; Zn: 80.79–110; Pb: 24.57–49.59; Cd: 0.099–0.324; Cr: 41.6–88.1; Mn: 343−520μg/g) and bivalves (Cu: 6.41–19.76; Zn: 35.5–85.5; Pb: 0.31–1.01; Cd: 0.51–0.67; Mn: 27.45−67.6 μg/g) are comparable to those reported for other moderately polluted world environments. SPM showed a less clear pattern. Metal concentrations in sediments displayed a clear geographical trend with values increasing with proximity to major urban centers. The clams (on dry weight) showed a complex pattern due to the variability introduced by age-related factors. Cd showed an apparent reverse industrial trend with higher concentrations in clams collected at distant stations. Zn, Pb and Mn showed no clear geographical pattern, whereas Cu increased in the clams collected in the most industrialized area. In addition, the bioaccumulation factors (BAF) were calculated. The result indicated that the studied Ruditapes philippinarum in Jiaozhou Bay possessed different bioaccumulation capacities for Cd, Zn, Cu, Pb and Mn, and Cd, Zn had a relatively high assimilation of those metals from sediment particles. A significant relationship with clam age was observed for Zn (positive) and Cu (negative) suggesting different physiological requirements for both metals with age. Trace metal concentrations measured in the tissue of the investigated clam were in the range considered safe by the WHO for human use.     

Risk-Based Prioritization of Air Pollution Monitoring Using Fuzzy Synthetic Evaluation Technique

Air pollution monitoring programs aim to monitor pollutants and their probable adverse effects at various locations over concerned area. Either sensitivity of receptors/location or concentration of pollutants is used for prioritizing the monitoring locations. The exposure-based approach prioritizes the monitoring locations based on population density and/or location sensitivity. The hazard-based approach prioritizes the monitoring locations using intensity (concentrations) of air pollutants at various locations. Exposure and hazard-based approaches focus on frequency (probability of occurrence) and potential hazard (consequence of damage), respectively. Adverse effects should be measured only if receptors are exposed to these air pollutants. The existing methods of monitoring location prioritization do not consider both factors (hazard and exposure) at a time. Towards this, a risk-based approach has been proposed which combines both factors: exposure frequency (probability of occurrence/exposure) and potential hazard (consequence).This paper discusses the use of fuzzy synthetic evaluation technique in risk computation and prioritization of air pollution monitoring locations. To demonstrate the application, common air pollutants like CO, NO_x, PM₁₀ and SO_x are used as hazard parameters. Fuzzy evaluation matrices for hazard parameters are established for different locations in the area. Similarly, fuzzy evaluation matrices for exposure parameters: population density, location and population sensitivity are also developed. Subsequently, fuzzy risk is determined at these locations using fuzzy compositional rules. Finally, these locations are prioritized based on defuzzified risk (crisp value of risk, defined as risk score) and the five most important monitoring locations are identified (out of 35 potential locations). These locations differ from the existing monitoring locations.     

Determination of toxic elements in waters and sediments from River Subin in the Ashanti Region of Ghana

Waters and sediments of Subin River, which flows through the industrial and commercial areas of Kumasi in the Ashanti region of Ghana, were geochemically investigated to ascertain heavy metal pollution levels due to anthropogenic activities. The study shows preoccupying pollution levels that constitute a threat to public and ecological systems. The waters of Subin River are neutral to slightly basic, inferred from pH values of 6.89–7.65). Electric conductivity (EC) of the waters ranges from 822 to 1,821 μs/cm and the range of total dissolved solids (TDS) is from 409 to 913 mg/l. Toxic elements contents of sediments and waters from 10 sites along the river were analysed by instrumental neutron activation analysis (INAA), and Al, As, Cd, Cr, Cu and Zn were determined. The concentrations of Al, As, Cd, Cr, Cu and Zn in the waters range between 4.02–15.18, 0.007–0.16, 0.002–0.05, 0.001–0.019, 1.32–7.04 and 4.28–10.2 mg/l, respectively. The contamination factors (CF) computed for the elements indicate that with the exception of sampling site S10, the sediments are polluted with Cd. Chromium contamination in the sediments is observed at S6 and S7, where the CF values were 1.39 and 1.52, respectively. The pollution load indices (PLI) were low (<1) and ranged from 0.14 to 0.75, suggesting that the overall sediment column of the river is not polluted.     

Response of non-point source pollutant loads to climate change in the Shitoukoumen reservoir catchment

The impacts of climate change on streamflow and non-point source pollutant loads in the Shitoukoumen reservoir catchment are predicted by combining a general circulation model (HadCM3) with the Soil and Water Assessment Tool (SWAT) hydrological model. A statistical downscaling model was used to generate future local scenarios of meteorological variables such as temperature and precipitation. Then, the downscaled meteorological variables were used as input to the SWAT hydrological model calibrated and validated with observations, and the corresponding changes of future streamflow and non-point source pollutant loads in Shitoukoumen reservoir catchment were simulated and analyzed. Results show that daily temperature increases in three future periods (2010–2039, 2040–2069, and 2070–2099) relative to a baseline of 1961–1990, and the rate of increase is 0.63°C per decade. Annual precipitation also shows an apparent increase of 11 mm per decade. The calibration and validation results showed that the SWAT model was able to simulate well the streamflow and non-point source pollutant loads, with a coefficient of determination of 0.7 and a Nash–Sutcliffe efficiency of about 0.7 for both the calibration and validation periods. The future climate change has a significant impact on streamflow and non-point source pollutant loads. The annual streamflow shows a fluctuating upward trend from 2010 to 2099, with an increase rate of 1.1 m³ s⁻¹ per decade, and a significant upward trend in summer, with an increase rate of 1.32 m³ s⁻¹ per decade. The increase in summer contributes the most to the increase of annual load compared with other seasons. The annual NH₄⁺-N load into Shitoukoumen reservoir shows a significant downward trend with a decrease rate of 40.6 t per decade. The annual TP load shows an insignificant increasing trend, and its change rate is 3.77 t per decade. The results of this analysis provide a scientific basis for effective support of decision makers and strategies of adaptation to climate change.     

Distribution of heavy metals in water, particulate matter and sediments of Gediz River (Eastern Aegean)

The present paper is the first document of heavy metal levels in surficial sediment, water and particulate matter of the Gediz River collected from five different sites in August, October 1998, February, June 1999. The present work attempts to establish the status of distribution and environmental implications of metals in the sediment, water and particulate matter and their possible sources of derivation. The concentrations of mercury ranged 0.037–0.81, 120–430; lead 0.59–1.5, 190–8,100; copper 0.24–1.6, 30–180; zinc 0.19–2.9, 10–80; manganese 30–170, 20–490; nickel 0.39–9.0, 100–510; iron 1.3–687, 100–6,200 μg/l in water and particulate matter, respectively. The maximum values in water were generally obtained in summer periods due to industrial and agricultural activities at Muradiye. The particulate metal concentrations also generally showed increased levels from the upper Gediz to the mouth of the river. Calculation of metal partition coefficients shows that the relative importance of the particulate and the water phases varies in response to water hydrochemistry and suspended solid content, but that most elements achieve a conditional equilibrium in the Gediz River. The metals ranged between Hg: 0.25–0.49, Cr: 59–814, Pb: 38–198, Cu: 15–148, Zn: 34–196, Mn: 235–1,371, Ni: 35–175, and Fe: 10,629–72,387 mg/kg in sediment. The significant increase of metals found in Muradiye suggested a pollution effect, related to anthropogenic wastes. Also, relatively high concentrations of Ni and Mn occurred in sampling site upstream, due to geochemical composition of the sediments. Maximum values of contamination factor for metals were noticed for sediment of Muradiye. The sampling stations have very high degree of contamination indicating serious anthropogenic pollution.     

Aerosol characteristics and surface radiative forcing components during a dust outbreak in Gwangju, Republic of Korea

Atmospheric surface aerosol radiative forcing (SARF) ΔF, forcing efficiency ΔF_e and fractional forcing efficiency ΔFF_e evaluated from cloud-screened narrowband spectral and thermal-offset-corrected radiometric observations during the Asia dust outbreak episodes in Gwangju, Republic of Korea are reported in this study. Columnar aerosol optical properties (aerosol optical depth (AOD), τ _aλ, Angstrom exponent α, mass concentration of fine and coarse mode particles) were also reported for the station between January 2000 and May 2001 consisting of 211cloud-free days. Results indicate that majority of the AOD were within the range 0.25–0.45 while some high aerosol events in which AODs ≥ 0.6 were observed during the severe dust episodes. For example, AOD increases from annual average value of 0.34 ± 0.13 at 501 nm to values >0.60 during the major dust events of March 27–30 and April 7–9, 2000, respectively. The α _{501–870 nm} which is often used as a qualitative indicator of aerosol particle size had values ranging from 0.01 to 1.77. The diurnal forcing efficiency ΔDF_e at Gwangju was estimated to be −81.10 ± 5.14 W m ⁻²/τ _{501 nm} and −47.09 ± 2.20 W m ⁻²/τ _{501 nm} for the total solar broadband and visible band pass, respectively while the fractional diurnal forcing efficiency ΔFDF_e were −15.8 ± 0.64%/τ _{501 nm} and −22.87 ± 1.13%/τ _{501 nm} for the same band passes. Analyses of the 5-day air-mass back trajectories were further developed for Gwangju in order to classify the air-mass and types of aerosol reaching the site during the Asia dust episodes.     

Trace Metal Levels in Mussels (Mytilus Galloprovincialis L. 1758) from Turkish Aegean Sea Coast

Bio-monitoring of some heavy metal levels (Cd, Pb, Zn, Cu) in whole edible soft parts of Mytilus galloprovincialis (L. 1758) was conducted in Turkish Aegean Sea coast during the period of September 2002–August 2003 seasonally. Moreover, some physico-chemical environmental parameters, also have been analysed in the same region. The values of some physico-chemical environmental parameters in coastal waters of Turkish Aegean Sea were changed between; 9.0–27.0 ^∘C for temperature, 31.93–40.45 psu for salinity, 7.35–8.48 for pH and 4.05–9.50 mg/l for dissolved oxygen. The levels of trace elements in whole edible soft parts including interstitial fluids of Mediterranean mussels M. galloprovincialis (L. 1758), sampled from 6 different regions of Turkish Aegean Sea coast have ranged between; 0.04–0.52 μg Cd/g wet weight, 0.49–1.72 μg Pb/g w.w., 0.95–1.85 Cu/g w.w., 16.11–37.15 μg Zn/g w.w. The highest values for all trace metals (Cd, Pb, Zn, Cu) were measured in inner part of Izmir Bay (station 3) and lowest in Sigacik and Gulluk Bay (station 5, 6). Generally heavy metal levels are lower than the results in soft mussel tissues reported from Mediterranean regions.