Dechlorination/detoxification of aromatic chlorides using fly ash under mild conditions

An efficient dechlorination/detroxification method for p-nitrochlorobenzene, p-chloroanisole and 1-chloronaphthalene on municipal waste incinerator fly ash in presence of reducing agents with water/alcohol mixtures was developed. Dechlorination% was higher in water/isopropanol mixture at temperature <100 °C. Metal contents of fly ash played a vital role in enhancing dechlorination at low temperature. Moreover, the fly ash particles provided the surface to accomplish reduction and substitution reactions by adsorbing the chlorinated aromatic compound, hydrogen and hydroxyl ions. The mechanism of dechlorination was envisaged.     

Catalytic detoxification of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans in fly ash

An efficient catalytic detoxification method for polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in fly ash produced by municipal waste incinerator has been studied using palladium on carbon (Pd/C) catalyst. As one of the trace components in fly ash, the detoxification of PCDD/Fs is very difficult because of the interferences of other persistent components with higher concentrations. However, the detoxification reaction of PCDD/Fs shows higher activity in water/isopropanol solution using commercial Pd/C catalyst at 40 degrees C under normal pressure. The results indicated that the catalytic degradation of PCDFs has been found to be easier than that of PCDDs. Moreover, the dechlorination ratios were higher for octa- and hepta-chlorinated congeners than those for tetra- and penta-chlorinated ones. The detoxification process worked well in water. The dechlorination efficiencies of almost all of the PCDD/Fs congeners can reach over 99% within a shorter reaction time.     

Enrichment of PCDDs/PCDFs in peripheral utilities of the municipal solid waste incineration facility

This study was performed to suggest the improvements through measuring the amounts of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs), re-synthesized in peripheral utilities (PUs) of a commercial-scale municipal solid waste incineration facility (MSWIF) where a few research results existed. The PUs examined in this study consisted of air pre-heaters (APHs) and gas/gas re-heater (GGRH) and kerosene-fired duct burner for selective catalytic reduction (SCR) process. PCDDs/PCDFs in flue gas were simultaneously measured at the inlet and outlet of PUs.Flue gas was cooled down from 380 °C to 249 °C by exchanging the heat with fresh air in APHs, and then heated up to 383 °C by GGRH and duct burner from 164 °C at the outlet of bag filter. The results showed that PCDDs/PCDFs were 3–4 times higher within this temperature range of PUs. In comparison of PCDDs/PCDFs concentrations at the inlet with those at the outlet of PUs, particulate-phase PCDDs/PCDFs were about 9.5–10 times enriched while gaseous-phase ones were decreased by about 33–41%. The PCDDs/PCDFs re-synthesized in the PUs, where PCDDs were relatively higher than PCDFs, showed somewhat different patterns compared to those formed at incinerators and emitted at stack. Through the investigations for PUs, we conclude that the PUs used in MSWIFs was a potential source for de novo synthesis of PCDDs/PCDFs.     

Enrichment of PCDDs/PCDFs in the cooling system of municipal solid waste incineration plants

This study measured the levels of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/PCDFs), destroyed or formed in combustors and re-synthesized in cooling systems. For the proper control of PCDDs/PCDFs in municipal solid waste (MSW) incinerators, three grate-type MSW incinerators were selected, two of which had boilers, and one of which had a water spray tower (WST) as a cooling system. At the combustor outlets, dusts were in the range of 1640-4270 mg/Sm3 and PCDDs/PCDFs were in the range of 0.103-2.619 ng-TEQ/Sm3, showing the different values according to the grate structure of combustor and the flow direction of flue gas. After the flue gases passed through the cooling system, PCDDs/PCDFs at the waste heat boiler (WHB) outlets were enriched to levels that were 10.8-13.6 times higher than those at the furnace outlets, but PCDDs/PCDFs at the WST outlet was reduced to 5% of the level found at the furnace outlet. The emission patterns, such as the ratio of PCDFs to PCDDs, the ratio of gaseous-phase to particulate-phase PCDDs/PCDFs, and the compositional percentiles of each 2,3,7,8-substituted congener varied according to the types of air pollution control devices (APCDs). Reducing re-synthesis in the cooling system rather than enhancing the removal efficiencies of the APCDs seems to be more effective for lowering the levels of PCDDs/PCDFs in MSW incineration plants.     

粉煤灰-粉煤灰合成沸石对Cs~+的固化

以电厂废弃物粉煤灰为原料、采用碱熔-水热法制备了粉煤灰合成A型沸石(以下简称沸石),再以沸石对溶液中的Cs+进行分离富集,最后在碱激发剂的作用下以粉煤灰和吸附后的沸石制得地聚合物固化体。对固化体的性能进行了评价,并探讨了固化机理。实验结果表明:在吸附温度25℃、初始Cs+质量浓度100 mg/L、固液比10.0 g/L的条件下,沸石对的Cs+的吸附率达98%,比粉煤灰提高了2倍以上;沸石掺量为20%~30%(w)时,固化体的抗压强度符合GB 14569.1—2011要求,固化体中Cs+的42 d浸出率和累计浸出分数均远优于GB 14569.1—2011限值,表现出优异的抗浸出性能。     

Recycling of municipal solid waste incinerator fly ash by using hydrocyclone separation

The municipal solid waste incinerators (MSWIs) in Taiwan generate about 300,000 tons of fly ash annually, which is mainly composed of calcium and silicon compounds, and has the potential for recycling. However, some heavy metals are present in the MSWI fly ash, and before recycling, they need to be removed or reduced to make the fly ash non-hazardous. Accordingly, the purpose of this study was to use a hydrocyclone for the separation of the components of the MSWI fly ash in order to obtain the recyclable portion. The results show that chloride salts can be removed from the fly ash during the hydrocyclone separation process. The presence of a dense medium (quartz sand in this study) is not only helpful for the removal of the salts, but also for the separation of the fly ash particles. After the dense-medium hydrocyclone separation process, heavy metals including Pb and Zn were concentrated in the fine particles so that the rest of the fly ash contained less heavy metal and became both non-hazardous and recyclable.     

Arsenic,selenium, and chromium speciation in fly ash

Journal of Material Cycles and Waste Management - Arsenic (As), selenium (Se), and chromium (Cr) are harmful to humans at certain concentrations, and can possibly be eluted from coal ash (fly ash)...     

Stabilization of heavy metals in MSWI fly ash using silica fume

The objective of this work was to investigate the feasibility and effectiveness of silica fume on stabilizing heavy metals in municipal solid waste incineration (MSWI) fly ash. In addition to compressive strength measurements, hydrated pastes were characterized by X-ray diffraction (XRD), thermal-analyses (DTA/TG), and MAS NMR (²⁷Al and ²⁹Si) techniques. It was found that silica fume additions could effectively reduce the leaching of toxic heavy metals. At the addition of 20% silica fume, leaching concentrations for Cu, Pb and Zn of the hydrated paste cured for 7 days decreased from 0.32 mg/L to 0.05 mg/L, 40.99 mg/L to 4.40 mg/L, and 6.96 mg/L to 0.21 mg/L compared with the MSWI fly ash. After curing for 135 days, Cd and Pb in the leachates were not detected, while Cu and Zn concentrations decreased to 0.02 mg/L and 0.03 mg/L. The speciation of Pb and Cd by the modified version of the European Community Bureau of Reference (BCR) extractions showed that these metals converted into more stable state in hydrated pastes of MSWI fly ash in the presence of silica fume. Although exchangeable and weak-acid soluble fractions of Cu and Zn increased with hydration time, silica fume addition of 10% can satisfy the requirement of detoxification for heavy metals investigated in terms of the identification standard of hazardous waste of China.     

Toxicity mitigation and solidification of municipal solid waste incinerator fly ash using alkaline activated coal ash

Municipal solid waste (MSW) incineration is a common and effective practice to reduce the volume of solid waste in urban areas. However, the byproduct of this process is a fly ash (IFA), which contains large quantities of toxic contaminants. The purpose of this research study was to analyze the chemical, physical and mechanical behaviors resulting from the gradual introduction of IFA to an alkaline activated coal fly ash (CFA) matrix, as a mean of stabilizing the incinerator ash for use in industrial construction applications, where human exposure potential is limited. IFA and CFA were analyzed via X-ray fluorescence (XRF), X-ray diffraction (XRD) and Inductive coupled plasma (ICP) to obtain a full chemical analysis of the samples, its crystallographic characteristics and a detailed count of the eight heavy metals contemplated in US Title 40 of the Code of Federal Regulations (40 CFR). The particle size distribution of IFA and CFA was also recorded. EPA's Toxicity Characteristic Leaching Procedure (TCLP) was followed to monitor the leachability of the contaminants before and after the activation. Also images obtained via Scanning Electron Microscopy (SEM), before and after the activation, are presented. Concrete made from IFA, CFA and IFA-CFA mixes was subjected to a full mechanical characterization; tests include compressive strength, flexural strength, elastic modulus, Poisson's ratio and setting time. The leachable heavy metal contents (except for Se) were below the maximum allowable limits and in many cases even below the reporting limit. The leachable Chromium was reduced from 0.153 down to 0.0045 mg/L, Arsenic from 0.256 down to 0.132 mg/L, Selenium from 1.05 down to 0.29 mg/L, Silver from 0.011 down to .001 mg/L, Barium from 2.06 down to 0.314 mg/L and Mercury from 0.007 down to 0.001 mg/L. Although the leachable Cd exhibited an increase from 0.49 up to 0.805 mg/L and Pd from 0.002 up to 0.029 mg/L, these were well below the maximum limits of 1.00 and 5.00 mg/L, respectively.     

Alkali-activated aerated blends: interaction effect of slag with low and high calcium fly ash

Journal of Material Cycles and Waste Management - This paper reports the influence of the addition of slag in a fly ash-based alkali-activated aerated system, using both Class-F and Class-C fly...     

Pyrolysis of low-density polyethylene using synthetic catalysts produced from fly ash

Catalytic pyrolysis of low-density polyethylene (LDPE) was investigated using various fly ash-derived silica–alumina catalysts (FSAs). FSAs were prepared by a simple activation method that basically includes NaOH treatment of fly ash by a fusion method, followed by an aging process. A series of LDPE pyrolysis experiments was conducted and the catalytic performance of FSAs was assessed in terms of the degradation temperature and the simulated boiling point distribution of the liquid products. The effects of synthesis conditions such as NaOH/fly ash weight ratio and aging time were examined by X-ray diffractometer (XRD), Brunauer-Emmett-Teller (BET) surface area analyzer, and scanning electron microscope to clarify the controlling factors affecting the catalytic activity. To obtain catalyst with high activity, it is necessary to produce sufficient silica and alumina species that can be easily co-precipitated into solid acid catalyst by destruction of the fly ash structure and to optimize the activation time for catalyst synthesis to prevent the transformation into inactive phases. The catalytic performance of FSA obtained from optimal conditions was equivalent to that of commercial catalysts, demonstrating the effectiveness of the catalyst.     

Investigation of MSWI fly ash melting characteristic by DSC-DTA

The melting process of MSWI (Municipal Solid Waste Incineration) fly ash has been studied by high-temperature DSC-DTA experiments. The experiments were performed at a temperature range of 20-1450 degrees C, and the considerable variables included atmosphere (O(2) and N(2)), heating rates (5 degrees C/min, 10 degrees C/min, 20 degrees C/min) and CaO addition. Three main transitions were observed during the melting process of fly ash: dehydration, polymorphic transition and fusion, occurring in the temperature range of 100-200 degrees C, 480-670 degrees C and 1101-1244 degrees C, respectively. The apparent heat capacity and heat requirement for melting of MSWI fly ash were obtained by DSC (Differential Scanning Calorimeter). A thermodynamic modeling to predict the heat requirements for melting process has been presented, and it agrees well with the experimental data. Finally, a zero-order kinetic model of fly ash melting transition was established. The apparent activation energy of MSWI fly ash melting transition was obtained.     

Improvements of nano-SiO2 on sludge/fly ash mortar

Sewage sludge ash has been widely applied to cementitious materials. In this study, in order to determine effects of nano-SiO(2) additives on properties of sludge/fly ash mortar, different amounts of nano-SiO(2) were added to sludge/fly ash mortar specimens to investigate their physical properties and micro-structures. A water-binding ratio of 0.7 was assigned to the mix. Substitution amounts of 0%, 10%, 20%, and 30% of sludge/fly ash (1:1 ratio) were proposed. Moreover, 0%, 1%, 2%, and 3% of nano-SiO(2) was added to the mix. Tests, including SEM and compressive strength, were carried out on mortar specimens cured at 3, 7, and 28 days. Results showed that sludge/fly ash can make the crystals of cement hydration product finer. Moreover, crystals increased after nano-SiO(2) was added. Hence, nano-SiO(2) can improve the effects of sludge/fly ash on the hydration of mortar. Further, due to the low pozzolanic reaction active index of sludge ash, early compressive strengths of sludge/fly ash mortar were decreased. Yet, nano-SiO(2) could help produce hydration crystals, which implies that the addition of nano-SiO(2) to mortar can improve the influence of sludge/fly ash on the development of the early strength of the mortar.     

粉煤灰处理阴离子表面活性剂废水及机理研究

采用粉煤灰作为吸附混凝剂,研究了粉煤灰对废水中阴离子表面活性剂十二烷基磺酸钠（SDS）的去除及机理。分析了粉煤灰投加量、吸附时间、pH值对废水中SDS去除率的影响,探讨了最佳条件下废水中SDS去除率,研究了粉煤灰动力学特征。结果表明,在200mL浓度50mg/L的SDS溶液中,调节pH值为13,加入70 g粉煤灰,搅拌20m in后,SDS的去除率为83.3%。粉煤灰对SDS的吸附符合Freund lich吸附等温式。     

Elution control of radioactive cesium in MSWI fly ash using water repellent treatment

Journal of Material Cycles and Waste Management - Radioactive cesium found in municipal solid waste incineration (MSWI) fly ash can be easily eluted through contact with environmentally sourced...     

粉煤灰在废水处理中的应用

就粉煤灰处理废水的研究与应用现状进行了综述.粉煤灰主要通过其吸附作用(物理吸附和化学吸附)处理废水,对于城市污水、工业废水、含重金属离子、F-、PO3-4废水等均有较好的处理效果.对粉煤灰进行物理或化学改性研制高效复合粉煤灰混凝剂是提高粉煤灰利用价值的有效途径之一.同时,提高粉煤灰吸附容量以及妥善处理吸附饱和灰是当前急需解决的问题.     

Vanadium recovery from oil fly ash by leaching, precipitation and solvent extraction processes

In order to reduce the environmental impact due to land disposal of oil fly ash from power plants and to valorize this waste material, the removal of vanadium was investigated using leaching processes (acidic and alkaline treatments), followed by a second step of metal recovery from leachates involving either solvent extraction or selective precipitation. Despite a lower leaching efficiency (compared to sulfuric acid), sodium hydroxide was selected for vanadium leaching since it is more selective for vanadium (versus other transition metals). Precipitation was preferred to solvent extraction for the second step in the treatment since: (a) it is more selective; enabling complete recovery of vanadate from the leachate in the form of pure ammonium vanadate; and (b) stripping of the loaded organic phase (in the solvent extraction process) was not efficient. Precipitation was performed in a two-step procedure: (a) aluminum was first precipitated at pH 8; (b) then ammonium chloride was added at pH 5 to bring about vanadium precipitation.     

Statistical modelling for the prediction and control of PCDDs and PCDFs emissions from municipal solid waste incinerators

The emissions of a full range of polychlorinated dibenzo-p-dioxins and furans (PCDDs/PCDFs) have become one of the most controversial issues in siting and building new municipal incinerators. The lack of comprehensive evaluation of the PCDDs/PCDFs formation and emission control technologies in earlier times resulted in ambiguity in the decision-making of incineration projects. Until the last decade, several emission tests of municipal solid waste incineration regarding to new combustion criteria, public regulations, and risk assessments were conducted and reported in the literature. However, only a few analyses of statistical prediction and control have been established. This paper presents a series of multiple linear regression models for PCDDs/PCDFs emission prediction and control corresponding to different types of incinerators. The data used in the regression analysis were integrated from several testing programmes held in North America. By applying these regression results, evaluation of various combustion criteria, public regulations, and environmental and health risk assessment can then be achieved. Such evaluation is valuable for some developing countries which do not have sufficient finance or engineering experience to pursue large scale emission tests, but need rapid promulgation of emissions control for municipal solid waste incinerators.     

Fluoride sorption by treated fly ash: kinetic and isotherm studies

High fluoride levels in drinking water have become a critical health hazard. In the present study, the performance of magnesia-loaded fly ash adsorption in the removal of fluoride from aqueous solution was investigated in a batch study. The effect of contact time, dosage, pH, temperature and agitation speed was studied at different values. The maximum removal efficiency was 88 % at 150 min. The effective dose of adsorbent was found to be 2.5 g/l. The optimum pH was found to be at pH 4. Kinetic studies and isotherm studies were also performed to understand the ability of the adsorbents. The monolayer adsorption capacity determined from the Langmuir adsorption equation was found to be 11.61 mg/g. The kinetic measurements suggested the involvement of pseudo-second-order kinetics in adsorption and were controlled by a particle diffusion process. Overall, the results of this study suggest that magnesia-loaded fly ash is an environmentally friendly, efficient and low-cost adsorbent, useful for the removal of fluoride from aqueous solution.     

Comparative study on the characteristics of fly ash and bottom ash geopolymers

This research was conducted to compare geopolymers made from fly ash and ground bottom ash. Sodium hydroxide (NaOH) and sodium silicate (Na(2)SiO(3)) solutions were used as activators. A mass ratio of 1.5 Na(2)SiO(3)/NaOH and three concentrations of NaOH (5, 10, and 15M) were used; the geopolymers were cured at 65 degrees C for 48 h. A Fourier transform infrared spectrometer (FT-IR), differential scanning calorimeter (DSC), and scanning electron microscope (SEM) were used on the geopolymer pastes. Geopolymer mortars were also prepared in order to investigate compressive strength. The results show that both fly ash and bottom ash can be utilized as source materials for the production of geopolymers. The properties of the geopolymers are dependent on source materials and the NaOH concentration. Fly ash is more reactive and produces a higher degree of geopolymerization in comparison with bottom ash. The moderate NaOH concentration of 10 M is found to be suitable and gives fly ash and bottom ash geopolymer mortars with compressive strengths of 35 and 18 MPa.