Siting MSW landfill using weighted linear combination and analytical hierarchy process (AHP) methodology in GIS environment (case study: Karaj)

Selection of landfill site is a complex process and needs many diverse criteria. The purpose of this paper is to evaluate the suitability of the studied site as landfill for MSW in Karaj. Using weighted linear combination (WLC) method and spatial cluster analysis (SCA), suitable sites for allocation of landfill for a 20-year period were identified. For analyzing spatial auto-correlation of the land suitability map layer (LSML), Maron’s I was used. Finally, using the analytical hierarchy process (AHP), the most preferred alternative for the landfill siting was identified. Main advantages of AHP are: relative ease of handling multiple criteria, easy to understand and effective handling of both qualitative and quantitative data.As a result, 6% of the study area is suitable for landfill siting and third alternative was identified as the most preferred for siting MSW landfill by AHP.The ranking of alternatives were obtained only by applying the WLC approach showed different results from the AHP. The WLC should be used only for the identification of alternatives and the AHP is used for prioritization. We suggest the employed procedure for other similar regions.     

Combining AHP with GIS for landfill site selection: A case study in the Lake Beyşehir catchment area (Konya,Turkey)

Landfills are the most common method for the disposal of municipal solid waste (MSW) in Turkey. However, determining the location of landfill sites is a difficult and complex process because it must combine social, environmental and technical parameters. Additionally, it depends on several criteria and regulations. The main objective of this study was to select of a landfill site for the Lake Bey?ehir catchment area. The Bey?ehir Lake is the largest freshwater lake and drinking water reservoir in Turkey, but there is no controlled landfill site in the region. Therefore, the landfill site should be determined such that the lake is protected. To determine the most suitable landfill site, an analytical hierarchy process (AHP) was combined with a geographic information system (GIS) to examine several criteria, such as geology/hydrogeology, land use, slope, height, aspect and distance from settlements, surface waters, roads, and protected areas (ecologic, scientific or historic). Each criterion was evaluated with the aid of AHP and mapped by GIS. Data were assorted into four suitability classes within the study area, i.e., high, moderate, low and very low suitability areas, which represented 3.24%, 7.55%, 12.70% and 2.81%, of the study area, respectively. Additionally, 73.70% was determined to be completely unsuitable for a landfill site. As a result, two candidate landfill sites are suggested and discussed. The final decision for landfill site selection will require more detailed field studies.     

Integrating multi-criteria decision analysis for a GIS-based hazardous waste landfill sitting in Kurdistan Province, western Iran

The evaluation of a hazardous waste disposal site is a complicated process because it requires data from diverse social and environmental fields. These data often involve processing of a significant amount of spatial information which can be used by GIS as an important tool for land use suitability analysis. This paper presents a multi-criteria decision analysis alongside with a geospatial analysis for the selection of hazardous waste landfill sites in Kurdistan Province, western Iran. The study employs a two-stage analysis to provide a spatial decision support system for hazardous waste management in a typically under developed region. The purpose of GIS was to perform an initial screening process to eliminate unsuitable land followed by utilization of a multi-criteria decision analysis (MCDA) to identify the most suitable sites using the information provided by the regional experts with reference to new chosen criteria. Using 21 exclusionary criteria, as input layers, masked maps were prepared. Creating various intermediate or analysis map layers a final overlay map was obtained representing areas for hazardous waste landfill sites. In order to evaluate different landfill sites produced by the overlaying a landfill suitability index system was developed representing cumulative effects of relative importance (weights) and suitability values of 14 non-exclusionary criteria including several criteria resulting from field observation. Using this suitability index 15 different sites were visited and based on the numerical evaluation provided by MCDA most suitable sites were determined.     

Integrating multi-criteria evaluation techniques with geographic information systems for landfill site selection: a case study using ordered weighted average

This paper presents a GIS-based multi-criteria decision analysis approach for evaluating the suitability for landfill site selection in the Polog Region, Macedonia. The multi-criteria decision framework considers environmental and economic factors which are standardized by fuzzy membership functions and combined by integration of analytical hierarchy process (AHP) and ordered weighted average (OWA) techniques. The AHP is used for the elicitation of attribute weights while the OWA operator function is used to generate a wide range of decision alternatives for addressing uncertainty associated with interaction between multiple criteria. The usefulness of the approach is illustrated by different OWA scenarios that report landfill suitability on a scale between 0 and 1. The OWA scenarios are intended to quantify the level of risk taking (i.e., optimistic, pessimistic, and neutral) and to facilitate a better understanding of patterns that emerge from decision alternatives involved in the decision making process.     

Multi-criteria GIS-based siting of an incineration plant for municipal solid waste

Siting a municipal solid waste (MSW) incineration plant requires a comprehensive evaluation to identify the best available location(s) that can simultaneously meet the requirements of regulations and minimise economic, environmental, health, and social costs. A spatial multi-criteria evaluation methodology is presented to assess land suitability for a plant siting and applied to Santiago Island of Cape Verde. It combines the analytical hierarchy process (AHP) to estimate the selected evaluation criteria weights with Geographic Information Systems (GIS) for spatial data analysis that avoids the subjectivity of the judgements of decision makers in establishing the influences between some criteria or clusters of criteria. An innovative feature of the method lies in incorporating the environmental impact assessment of the plant operation as a criterion in the decision-making process itself rather than as an a posteriori assessment. Moreover, a two-scale approach is considered. At a global scale an initial screening identifies inter-municipal zones satisfying the decisive requirements (socio-economic, technical and environmental issues, with weights respectively, of 48%, 41% and 11%). A detailed suitability ranking inside the previously identified zones is then performed at a local scale in two phases and includes environmental assessment of the plant operation. Those zones are ranked by combining the non-environmental feasibility of Phase 1 (with a weight of 75%) with the environmental assessment of the plant operation impact of Phase 2 (with a weight of 25%). The reliability and robustness of the presented methodology as a decision supporting tool is assessed through a sensitivity analysis. The results proved the system effectiveness in the ranking process.     

Optimization for MSW logistics of new Xicheng and new Dongcheng districts in Beijing based on maximum capacity of transfer stations

The new Xicheng and new Dongcheng districts of Beijing in 2010 were chosen as the research object. Based on the analysis of the current municipal solid waste (MSW) logistics system, the transfer station’s processing capacity and the terminal treatment facilities' conditions of the two new districts and other districts, a MSW logistics system was built using geographic information system (GIS) and analytic network process methods considering transregional treatment. The new logistics (MSW from new Xicheng was collected for Majialou. MSW from old Dongcheng and Xuanwu was collected for Datun and Xiaowuji, respectively) proved to be an improvement with a 10 % less collection fee, 111 % output–input ratio after transfer station (include) and 0.8:4.6:4.6 I:C:L (incineration:compost:landfill). After Nangong, Gaoantun II and Asuwei incineration are established, the output–input ratio of the new logistics will reach 114 %, and I:C:L will reach 3.6:4.2:2.2 which is environmentally friendly and nearer to the 4:3:3 Beijing government target. For a full load of every transfer station, the complement schemes were also presented and contrasted based on GIS analysis. The results have great theoretical and practical significance in transregional treatment and improving resource management level of MSW.     

Multi-objective optimization of solid waste flows: environmentally sustainable strategies for municipalities

An approach to sustainable municipal solid waste (MSW) management is presented, with the aim of supporting the decision on the optimal flows of solid waste sent to landfill, recycling and different types of treatment plants, whose sizes are also decision variables. This problem is modeled with a non-linear, multi-objective formulation. Specifically, four objectives to be minimized have been taken into account, which are related to economic costs, unrecycled waste, sanitary landfill disposal and environmental impact (incinerator emissions). An interactive reference point procedure has been developed to support decision making; these methods are considered appropriate for multi-objective decision problems in environmental applications. In addition, interactive methods are generally preferred by decision makers as they can be directly involved in the various steps of the decision process. Some results deriving from the application of the proposed procedure are presented. The application of the procedure is exemplified by considering the interaction with two different decision makers who are assumed to be in charge of planning the MSW system in the municipality of Genova (Italy).     

Fuzzy multicriteria disposal method and site selection for municipal solid waste

The use of fuzzy multiple criteria analysis (MCA) in solid waste management has the advantage of rendering subjective and implicit decision making more objective and analytical, with its ability to accommodate both quantitative and qualitative data. In this paper a modified fuzzy TOPSIS methodology is proposed for the selection of appropriate disposal method and site for municipal solid waste (MSW). Our method is superior to existing methods since it has capability of representing vague qualitative data and presenting all possible results with different degrees of membership. In the first stage of the proposed methodology, a set of criteria of cost, reliability, feasibility, pollution and emission levels, waste and energy recovery is optimized to determine the best MSW disposal method. Landfilling, composting, conventional incineration, and refuse-derived fuel (RDF) combustion are the alternatives considered. The weights of the selection criteria are determined by fuzzy pairwise comparison matrices of Analytic Hierarchy Process (AHP). It is found that RDF combustion is the best disposal method alternative for Istanbul. In the second stage, the same methodology is used to determine the optimum RDF combustion plant location using adjacent land use, climate, road access and cost as the criteria. The results of this study illustrate the importance of the weights on the various factors in deciding the optimized location, with the best site located in Çatalca. A sensitivity analysis is also conducted to monitor how sensitive our model is to changes in the various criteria weights.     

Combining stakeholder analysis and spatial multicriteria evaluation to select and rank inert landfill sites

This paper presents a method based on the combination of stakeholder analysis and spatial multicriteria evaluation (SMCE) to first design possible sites for an inert landfill, and then rank them according to their suitability. The method was tested for the siting of an inert landfill in the Sarca’s Plain, located in south-western Trentino, an alpine region in northern Italy. Firstly, stakeholder analysis was conducted to identify a set of criteria to be satisfied by new inert landfill sites. SMCE techniques were then applied to combine the criteria, and obtain a suitability map of the study region. Subsequently, the most suitable sites were extracted by taking into account also thresholds based on size and shape. These sites were then compared and ranked according to their visibility, accessibility and dust pollution. All these criteria were assessed through GIS modelling. Sensitivity analyses were performed on the results to assess the stability of the ranking with respect to variations in the input (criterion scores and weights). The study concluded that the three top-ranking sites are located close to each other, in the northernmost sector of the study area. A more general finding was that the use of different criteria in the different stages of the analysis allowed to better differentiate the suitability of the potential landfill sites.     

Siting MSW landfills with a spatial multiple criteria analysis methodology

The present work describes a spatial methodology which comprises several methods from different scientific fields such as multiple criteria analysis, geographic information systems, spatial analysis and spatial statistics. The final goal of the methodology is to evaluate the suitability of the study region in order to optimally site a landfill. The initial step is the formation of the multiple criteria problem's hierarchical structure. Then the methodology utilizes spatial analysis processes to create the evaluation criteria, which are mainly based on Greek and EU legislation, but are also based on international practice and practical guidelines. The relative importance weights of the evaluation criteria are estimated using the analytic hierarchy process. With the aid of the simple additive weighting method, the suitability for landfill siting of the study region is finally evaluated. The resulting land suitability is reported on a grading scale of 0-10, which is, respectively, from least to most suitable areas. The last step is a spatial clustering process, which is being performed in order to reveal the most suitable areas, allowing an initial ranking and selection of candidate landfill sites. The application of the presented methodology in the island of Lemnos in the North Aegean Sea (Greece) indicated that 9.3% of the study region is suitable for landfill siting with grading values greater than 9.     

A hybrid method for quasi-three-dimensional slope stability analysis in a municipal solid waste landfill

Limited space for accommodating the ever increasing mounds of municipal solid waste (MSW) demands the capacity of MSW landfill be maximized by building landfills to greater heights with steeper slopes. This situation has raised concerns regarding the stability of high MSW landfills. A hybrid method for quasi-three-dimensional slope stability analysis based on the finite element stress analysis was applied in a case study at a MSW landfill in north-east Spain. Potential slides can be assumed to be located within the waste mass due to the lack of weak foundation soils and geosynthetic membranes at the landfill base. The only triggering factor of deep-seated slope failure is the higher leachate level and the relatively high and steep slope in the front. The valley-shaped geometry and layered construction procedure at the site make three-dimensional slope stability analyses necessary for this landfill. In the finite element stress analysis, variations of leachate level during construction and continuous settlement of the landfill were taken into account. The "equivalent" three-dimensional factor of safety (FoS) was computed from the individual result of the two-dimensional analysis for a series of evenly spaced cross sections within the potential sliding body. Results indicate that the hybrid method for quasi-three-dimensional slope stability analysis adopted in this paper is capable of locating roughly the spatial position of the potential sliding mass. This easy to manipulate method can serve as an engineering tool in the preliminary estimate of the FoS as well as the approximate position and extent of the potential sliding mass. The result that FoS obtained from three-dimensional analysis increases as much as 50% compared to that from two-dimensional analysis implies the significance of the three-dimensional effect for this study-case. Influences of shear parameters, time elapse after landfill closure, leachate level as well as unit weight of waste on FoS were also investigated in this paper. These sensitivity analyses serve as the guidelines of construction practices and operating procedures for the MSW landfill under study.     

Mechanical behavior of typical hazardous waste and its influence on landfill stability during operation

The stability of hazardous waste (HW) landfill is a major security risk to the landfill environmental safety. The mechanical behavior of waste controls many aspects of landfill design and operation, including stability and settlement issues and the integrity of geosynthetic and liner components. This study presents the results of a laboratory experiment to learn the mechanical properties of HW collected from the Hangzhou HW landfill. Measured mechanical behavior was compared with results for municipal solid waste (MSW) to assess their discrepancies. The particle size of HW was analyzed by the sieving and hydrometer methods. Because HW comes primarily from industrial plants in the form of sludge or slag, their particle sizes are generally smaller than those of MSW. This study indicates that the shear strength parameters of HW are more sensitive to the methods of testing and calculation than those of MSW. Numerical simulations demonstrate that the safety factor of a landfill is affected by the mechanical properties of HW, especially cohesion and friction angle. Because of the lower particle size and wider compression ratio, compared to MSW, an HW landfill should be taken more care in its operational procedures so as to increase its stability.     

Approach for the use of MSW settlement predictions in the assessment of landfill capacity based on reliability analysis

In the analysis and design of municipal solid waste (MSW) landfills, there are many uncertainties associated with the properties of MSW during and after MSW placement. Several studies are performed involving different laboratory and field tests to understand the complex behavior and properties of MSW, and based on these studies, different models are proposed for the analysis of time dependent settlement response of MSW. For the analysis of MSW settlement, it is very important to account for the variability of model parameters that reflect different processes such as primary compression under loading, mechanical creep and biodegradation. In this paper, regression equations based on response surface method (RSM) are used to represent the complex behavior of MSW using a newly developed constitutive model. An approach to assess landfill capacities and develop landfill closure plans based on prediction of landfill settlements is proposed. The variability associated with model parameters relating to primary compression, mechanical creep and biodegradation are used to examine their influence on MSW settlement using reliability analysis framework and influence of various parameters on the settlement of MSW are estimated through sensitivity analysis.     

Aging and compressibility of municipal solid wastes

The expansion of a municipal solid waste (MSW) landfill requires the ability to predict settlement behavior of the existing landfill. The practice of using a single compressibility value when performing a settlement analysis may lead to inaccurate predictions. This paper gives consideration to changes in the mechanical compressibility of MSW as a function of the fill age of MSW as well as the embedding depth of MSW. Borehole samples representative of various fill ages were obtained from five boreholes drilled to the bottom of the Qizhishan landfill in Suzhou, China. Thirty-one borehole samples were used to perform confined compression tests. Waste composition and volume-mass properties (i.e., unit weight, void ratio, and water content) were measured on all the samples. The test results showed that the compressible components of the MSW (i.e., organics, plastics, paper, wood and textiles) decreased with an increase in the fill age. The in situ void ratio of the MSW was shown to decrease with depth into the landfill. The compression index, Cc, was observed to decrease from 1.0 to 0.3 with depth into the landfill. Settlement analyses were performed on the existing landfill, demonstrating that the variation of MSW compressibility with fill age or depth should be taken into account in the settlement prediction.     

Effect of leachate recirculation on the migration of copper and zinc in municipal solid waste and municipal solid waste incineration bottom ash co-disposed landfill

Municipal solid waste incinerator (MSWI) bottom ash was allowed to be disposed of with municipal solid waste (MSW) in landfill sites in the recently enacted standard of China. In this study, three sets of simulated landfill reactors, namely, conventional MSW landfill (CL), conventional MSWI bottom ash and MSW co-disposed landfill (CCL), and leachate recirculated MSWI bottom ash and MSW co-disposed landfill (RCL), were operated to investigate the environmental impact of the co-disposal. The effect of leachate recirculation on the migration of Cu and Zn in the co-disposed landfill was also presented. The results showed that the co-disposal of MSWI bottom ash with MSW would not enhance the leaching of Cu and Zn from landfill. However, the co-disposal increased the Cu and Zn contents of the refuse in the bottom layer of the landfill from 56.7 to 65.3 mg/kg and from 210 to 236 mg/kg, respectively. The recirculation of the leachate could further increase the Cu and Zn contents of the refuse in the bottom layer of the landfill to 72.9 and 441 mg/kg, respectively. Besides these observations, the results also showed that the co-disposed landfill with leachate recirculation could facilitate the stabilization of the landfill.     

A critique of risk modeling and risk assessment of municipal landfills based on U.S. Environmental Protection Agency techniques

Environmental risks are a growing public concern in America. The threat of contaminated drinking water from municipal solid waste (MSW) landfills is receiving increased attention from citizens and from the United States Environmental Protection Agency (USEPA). Examination of USEPA data collected from MSW landfills reveals approximate risks posed by these landfills. USEPA research suggests that 60% of MSW landfills present less than a 1 in 10 billion risk of cancer incidence. Another 6% pose risks less than 1 in a billion, while 17% present risks less than 1 in a million. This study addresses the USEPA risk assessment techniques and models for estimating MSW landfill risks. USEPA data for toxic constituents of landfill leachate are also analysed in order to better understand the difficulties encountered in estimating landfill risks. The study also presents a brief discussion of public perceptions of risk as they relate to communicating the USEPA landfill model results to those who might be affected.     

Leachate generation and biogas energy recovery in the Jebel Chakir municipal solid waste landfill,Tunisia

A survey was conducted between 2006 and 2008 in order to identify municipal solid waste (MSW) composition and its influence on leachate generation and to assess the amount of biogas yield from the Jebel Chakir landfill in Tunis City. The organic fraction was the predominant compound in the MSW, followed by paper, fine, plastic, leather, rubber, metal, textile, glass and ceramic. The average MSW moisture content varies from 60 % in the wet season to 80 % in the dry one. The recognised MSW composition is well representative if compared to that of cities in developing countries. A large leachate quantity is produced in the landfill of Jebel Chakir, despite the negative water balance of the site. Based on the annual MSW landfilled quantities and using the LandGEM model, the expected peak landfill gas (LFG) production is estimated to occur 1 year after the landfill closure with a rate of 3.53 × 10⁷ m³/year. The analysis of the potential conversion of LFG to electric energy shows it at a total LFG-to-electricity energy of around 257 GWh with a heating value of 4,475 kcal/m³ based on an LFG collection efficiency of 33 % and energy efficiency of 33 % giving an economic feasibility for a 10 MW power plant.     

Constitutive model for municipal solid waste incorporating mechanical creep and biodegradation-induced compression

A constitutive model is proposed to describe the stress–strain behavior of municipal solid waste (MSW) under loading using the critical state soil mechanics framework. The modified cam clay model is extended to incorporate the effects of mechanical creep and time dependent biodegradation to calculate total compression under loading. Model parameters are evaluated based on one-dimensional compression and triaxial consolidated undrained test series conducted on three types of MSW: (a) fresh MSW obtained from working phase of a landfill, (b) landfilled waste retrieved from a landfill after 1.5 years of degradation, and (c) synthetic MSW with controlled composition. The model captures the stress–strain and pore water pressure response of these three types of MSW adequately. The model is useful for assessing the deformation and stability of landfills and any post-closure development structures located on landfills.     

Transshipment site selection using the AHP and TOPSIS approaches under fuzzy environment

Site selection is an important issue in waste management. Selection of the appropriate solid waste site requires consideration of multiple alternative solutions and evaluation criteria because of system complexity. Evaluation procedures involve several objectives, and it is often necessary to compromise among possibly conflicting tangible and intangible factors. For these reasons, multiple criteria decision-making (MCDM) has been found to be a useful approach to solve this kind of problem. Different MCDM models have been applied to solve this problem. But most of them are basically mathematical and ignore qualitative and often subjective considerations. It is easier for a decision-maker to describe a value for an alternative by using linguistic terms. In the fuzzy-based method, the rating of each alternative is described using linguistic terms, which can also be expressed as triangular fuzzy numbers. Furthermore, there have not been any studies focused on the site selection in waste management using both fuzzy TOPSIS (technique for order preference by similarity to ideal solution) and AHP (analytical hierarchy process) techniques. In this paper, a fuzzy TOPSIS based methodology is applied to solve the solid waste transshipment site selection problem in Istanbul, Turkey. The criteria weights are calculated by using the AHP.     

Management of municipal solid waste in the Three Gorges region

As the fourth phase of the Three Gorges reservoir project commenced in 2008, the rate of water flow in the Yangtze River has obviously decelerated further downstream and water clarity within the storage facility has decreased. Meanwhile, the rate of urbanization in the region is adding to the amount of municipal solid waste (MSW) being generated by every day life. The composition of the waste is becoming more diversified and complicated, thereby presenting an increasing threat to the ecological environment and water resources of the Three Gorges region. This paper is a probe into MSW in terms of its characteristics as well as methods of storage, collection, transportation, recycling, treatment and disposal, the protection of environmental ecosystems. Municipal solid waste management (MSWM) is one of the major environmental problems in the Three Gorges region, and indeed the whole of China. Based on the analysis of the present situation of MSWM and its treatment/disposal, some methods of sorting, recycling, decomposing, incineration and reuse are described, sanitary landfill as the main disposal method in Chongqing city, incineration being the second. Sanitary landfill or dump was also used for MSW treatment in the Three Gorges region, and this paper also provides some suggestions for improving MSWM in the Three Gorges region.