Pyrolysis of virgin and waste polypropylene and its mixtures with waste polyethylene and polystyrene

A comparison of waste and virgin polypropylene (PP) plastics under slow pyrolysis conditions is presented. Moreover, mixtures of waste PP with wastes of polyethylene (PE) and polystyrene (PS) were pyrolyzed under the same operating conditions. Not only the impact of waste on degradation products but also impacts of the variations in the mixing ratio were investigated. The thermogravimetric weight loss curves and their derivatives of virgin and waste PP showed differences due to the impurities which are dirt and food residues. The liquid yield distribution concerning the aliphatic, mono-aromatic and poly-aromatic compounds varies as the ratio of PP waste increases in the waste plastic mixtures. In addition to this, the alkene/alkane ratio of gas products shows variations depending on the mixing ratio of wastes.     

土壤残留塑料的热降解脱附研究

针对土壤的塑料污染问题,提出一种采用热脱附降解技术修复污染土壤的方法.选取4种土壤中常见的残留塑料(聚乙烯(PE)、聚氯乙烯(PVC)、聚对苯二甲酸乙二酯(PET)、聚丙烯(PP))为研究对象,通过控制热解温度和土壤含水率对各污染土壤的修复效果进行探究.实验结果表明:在500℃的最佳热解温度下处理60 min,PE、P...     

Effects of temperature zones on pyrolysis products of mixed plastic waste

Journal of Material Cycles and Waste Management - Five of the most prevalent plastics in the Chinese market (polypropylene (PP), polyvinyl chloride (PVC), high-density polyethylene (PE),...     

Pyrolysis and dehalogenation of plastics from waste electrical and electronic equipment (WEEE): A review

Plastics from waste electrical and electronic equipment (WEEE) have been an important environmental problem because these plastics commonly contain toxic halogenated flame retardants which may cause serious environmental pollution, especially the formation of carcinogenic substances polybrominated dibenzo dioxins/furans (PBDD/Fs), during treat process of these plastics. Pyrolysis has been proposed as a viable processing route for recycling the organic compounds in WEEE plastics into fuels and chemical feedstock. However, dehalogenation procedures are also necessary during treat process, because the oils collected in single pyrolysis process may contain numerous halogenated organic compounds, which would detrimentally impact the reuse of these pyrolysis oils. Currently, dehalogenation has become a significant topic in recycling of WEEE plastics by pyrolysis. In order to fulfill the better resource utilization of the WEEE plastics, the compositions, characteristics and dehalogenation methods during the pyrolysis recycling process of WEEE plastics were reviewed in this paper. Dehalogenation and the decomposition or pyrolysis of WEEE plastics can be carried out simultaneously or successively. It could be ‘dehalogenating prior to pyrolysing plastics’, ‘performing dehalogenation and pyrolysis at the same time’ or ‘pyrolysing plastics first then upgrading pyrolysis oils’. The first strategy essentially is the two-stage pyrolysis with the release of halogen hydrides at low pyrolysis temperature region which is separate from the decomposition of polymer matrixes, thus obtaining halogenated free oil products. The second strategy is the most common method. Zeolite or other type of catalyst can be used in the pyrolysis process for removing organohalogens. The third strategy separate pyrolysis and dehalogenation of WEEE plastics, which can, to some degree, avoid the problem of oil value decline due to the use of catalyst, but obviously, this strategy may increase the cost of whole recycling process.     

Development of a catalytic dehalogenation (Cl,Br) process for municipal waste plastic-derived oil

Dehalogenation is a key technology in the feedstock recycling of mixed halogenated waste plastics. In this study, two different methods were used to clarify the effectiveness of our proposed catalytic dehalogenation process using various carbon composites of iron oxides and calcium carbonate as the catalyst/sorbent. The first approach (a two-step process) was to develop a process for the thermal degradation of mixed halogenated waste plastics, and also develop dehalogenation catalysts for the catalytic dehydrochlorination of organic chlorine compounds from mixed plastic-derived oil containing polyvinyl chloride (PVC) using a fixed-bed flow-type reactor. The second approach (a single-step process) was the simultaneous degradation and dehalogenation of chlorinated (PVC) and brominated (plastic containing brominated flame retardant, HIPS–Br) mixed plastics into halogen-free liquid products. We report on a catalytic dehalogenation process for the chlorinated and brominated organic compounds formed by the pyrolysis of PVC and brominated flame retardant (HIPS–Br) mixed waste plastics [(polyethylene (PE), polypropylene (PP), and polystyrene (PS)], and also other plastics. During dehydrohalogenation, the iron- and calcium-based catalysts were transformed into their corresponding halides, which are also very active in the dehydrohalogenation of organic halogenated compounds. The halogen-free plastic-derived oil (PDO) can be used as a fuel oil or feedstock in refineries.     

Two-stage thermal gasification of polyolefins

Plastic pellets of polyethylene (PE), polypropylene (PP), and polystyrene (PS) were gasified in a two-stage thermal degradation process. The first stage is the conversion of polyolefins to distilled oils using a melting vessel. In the second stage, the oils from the first stage are gasified using a tubular reactor. The distilled oil yields of PE, PP, and PS in the first stage were 84, 89, 92 wt%, respectively, each at 470°C. The total gas yields of PE, PP, and PS in the second stage were 80, 74, and 6.2 wt%, respectively, each at 800°C. The main components of the product gas for PE and PP were methane and olefins such as ethene and propene. Some aromatic oils, including benzene, toluene, and xylene, were also produced as by-products. The amount of carbonaceous residue, or coke, was very low (less than 1 wt%). By dividing the process into two stages, the coking rate was considerably reduced compared with direct gasification of the polyolefins. Received: July 19, 2000 / Accepted: September 17, 2000     

Thermogravimetric analysis and kinetic study on pyrolysis of representative medical waste composition

To obtain detailed information on the pyrolysis characteristics, a thermogravimetric study on the pyrolysis of 14 typical medical waste compositions was carried out in thermogravimetric analysis (TGA) equipment using dynamic techniques in a stream of N(2). An index representing pyrolysis reactivity of waste was presented. Kinetic parameters were obtained by Coats-Redfern method and used to model the TG curve. The results showed that: (a) Plastic, protein, cellulosic material, synthetic fibre, and rubber entered pyrolysis process in succession. (b) There was one decomposition stage in the pyrolysis of one-off medical glove, operating glove, cellulosic waste, absorbable catgut suture and adhesive plaster, while other components had two obvious weight loss stages. (c) The obtained apparent activation energy for second stage pyrolysis was comparably higher than that for first stage. (d) Each stage was controlled by only one kinetic mechanism, in which kinetic parameters were constant. (e) The degradation kinetics of medical waste may be affected by special physical and chemical treatment in the product manufacturing process. (f) Among 13 waste samples, the pyrolysis index of cellulosic matter was the highest, which indicated cellulosic matter had strong pyrolysis reactivity. (g) With increasing heating rate, TG curve and DTG peak shifted to high temperatures and main reaction interval of the sample became longer.     

Reaction Kinetic Model For Optimal Pyrolysis Of Plastic Waste Mixtures

Reaction kinetics at various temperatures for pyrolysis of mixtures of plastic waste [polyethylene(PE) and polystyrene(PS)] are modelled in terms of five types of pyrolysis reaction. The model development is based on the assumption that as plastic wastes are heated in a non-reactive environment they are decomposed homogeneously to various products of gas, oil and char by a first-order rate, irreversible reaction and isothermal condition. Among the five models, the type II model in which the activated polymer exists as an intermediate product is the most accurate in predicting the pyrolysis products of pure PE or pure PS. Also, for mixtures of plastics both type II and IV models can be used to explain the composition of pyrolysis products. Furthermore, from the analysis of variance (ANOVA), the mixing ratio and temperature are shown to be the parameters that have the greatest effect on the pyrolysis reaction of polymer waste mixture. The pyrolysis reaction time for the maximum oil production from PE-PS mixtures is shorter than for PE alone and approaches that of PS alone. Oil production increases with increase of PS content. The optimal temperature for maximum oil production is 600°C for the pyrolysis of 2:8, 5:5 and 1:0 mixtures (w/w) of PE and PS. Oil production for PS alone is constant when the pyrolysis is above 600°C.     

Pyrolysis characteristics of bean dregs and in situ visualization of pyrolysis transformation

Biomass is an important renewable and sustainable source of energy. Waste products from biomass are considered as attractive feedstocks for the production of fuel. This work deals with the pyrolysis of bean dregs, a biomass waste from soybean processing industry. A technique has been developed to study bean dregs pyrolysis by in situ visualization of bean dregs transformation in a quartz capillary under a microscope using a charge-coupled device (CCD) camera monitoring system. The technique enables us to observe directly the processes and temperatures of bean dregs transformation during pyrolysis. In situ visualization of reaction revealed that how oily liquids are generated and expulsed concurrently from bean dregs during pyrolysis. Pyrolysis characteristics were investigated under a highly purified N₂ atmosphere using a thermogravimetric analyzer from room temperature to 800 °C at different heating rates of 10, 30 and 50 °C/min. The results showed that three stages appeared in this thermal degradation process. The initial decomposition temperature and the peak shifted towards higher temperature with an increase in heating rate. Kinetic parameters in terms of apparent activation energy and pre-exponential factor were determined.     

Pyrolysis of polyethylene mixed with paper and wood: Interaction effects on tar, char and gas yields

In the present study the interactions between the main constituents of the refuse derived fuel (plastics, paper, and wood) during pyrolysis were studied. Binary mixtures of polyethylene-paper and polyethylene/sawdust have been transformed into pellets and pyrolyzed. Various mixtures with different composition were analyzed and pyrolysis products (tar, gas, and char) were collected. The mixtures of wood/PE and paper/PE have a different behavior. The wood/PE mixtures showed a much reduced interaction of the various compounds because the yields of pyrolysis products of the mixture can be predicted as linear combination of those of the pure components. On the contrary, a strong char yield increase was found at a low heating rate for paper/PE mixtures. In order to explain the results, the ability of wood and paper char to adsorb and convert the products of PE pyrolysis into was studied. Adsorption and desorption tests were performed on the char obtained by paper and wood by using n-hexadecane as a model compound for the heavy products of PE pyrolysis.     

Analysis of the combustion and pyrolysis of dried sewage sludge by TGA and MS

In this study, the combustion and pyrolysis processes of three sewage sludge were investigated. The sewage sludge came from three wastewater treatment plants.Proximate and ultimate analyses were performed. The thermal behaviour of studied sewage sludge was investigated by thermogravimetric analysis with mass spectrometry (TGA-MS). The samples were heated from ambient temperature to 800 °C at a constant rate 10 °C/min in air (combustion process) and argon flows (pyrolysis process). The thermal profiles presented in form of TG/DTG curves were comparable for studied sludges. All TG/DTG curves were divided into three stages. The main decomposition of sewage sludge during the combustion process took place in the range 180–580 °C with c.a. 70% mass loss. The pyrolysis process occurred in lower temperature but with less mass loss. The evolved gaseous products (H₂, CH₄, CO₂, H₂O) from the decomposition of sewage sludge were identified on-line.     

Molecular Modification and Compatibilization of Collected Polyethylene

The increasing use of plastics in packaging materials leads to growing amounts of plastic waste. Recycling material is generally regarded as advantageous. But in fact very few products are made from plastic waste, partly this can be explained by that little is known about the recycling process and the properties of collected materials. There is a need for injection moulding grades of recycled polyethylene, while large amounts of extrusion grades are available from packaging waste. A controlled way of de-branching or partly degrading PE would be desirable. Peroxides are commonly used to crosslink polyolefins, but under certain conditions a chain scission reaction occur. Another problem encountered with recycling of polyethylene are the poor miscibility of low amounts contaminations, i. e. polypropylene. A compatibilizer can improve properties of such polymer blends, in this work EPDM is used as compatibilzer. Studies of mechanical properties and viscosity measurements show that it is possible to partly degrade PE with peroxide exposing it to high temperature and oxygen. The properties of PE/PP blends were improved with EPDM as compatibilizer.     

Thermal pyrolysis of fresh and waste fishing nets

Kinetic tests on the pyrolysis of nylon-6 taken from fresh (new) fishing nets and waste fishing nets were conducted using thermogravimetric analysis at heating rates of 0.5, 1.0 and 2.0 degrees C/min. The main region of decomposition of both materials was between 340 and 440 degrees C at each heating rate. The region of decomposition for the nylon-6 from the waste fishing nets was slightly lower than that of the fresh fishing nets. The result shows that the value of activation energies increased from 128 to 433 kJ mol(-1) as the conversion of the pyrolysis reaction increased from 5% to 95%. Nylon-6 from the fresh fishing nets was pyrolyzed in a micro-scale tubing bomb reactor for 60, 80 and 100 min at 440 degrees C. The yield of pyrolyzed gases increased from 3.94 to 5.50 wt% with reaction time. The selectivity to specific hydrocarbons was not detected from the pyrolyzed oil and the carbon number distribution of the pyrolyzed oil was random.     

Studies on the pyrolysis behavior of gasification and melting systems for municipal solid waste

 It is important to investigate the pyrolysis processes of municipal solid waste (MSW) in the same way as for any mixture comprised of multiple substances. In this article, a two-reaction model for a variety of MSW mixtures is proposed to predict mass changes due to pyrolysis. In order to formulate the model based on pyrolysis kinetics, we conducted experiments to determine the kinetic model parameters. By thermal analysis of the typical components of MSW, mass changes attributable to the pyrolysis reaction were found at about 350°C for paper, 400°–500°C for plastics, and 200°–400°C for garbage (dry condition). Activation energies were obtained by the Ozawa method based on the mass changes in pyrolysis. Thus, the pyrolysis behavior is formulated as a function of temperature. Then the pyrolysis mass change of the mixture can be predicted by using a weighted sum of the individual components. The model proved useful in experiments with real waste (refuse-derived fuels). Furthermore, the weight yields (pyrolysis gas, tars, solid residues) of the mixture can be calculated by their additive property after measuring the mass balance of each component. Received: May 11, 2001 / Accepted: November 16, 2001     

Total recycling of CCA treated wood waste by low-temperature pyrolysis

A system to turn a potentially harmful stream of solid waste into a set of substreams with either commercial value or highly concentrated residual streams is presented. The waste which is considered is metal impregnated (in particular Chromated Copper Arsenate (CCA) treated) wood waste and timber, such as telephone poles, railway sleepers, timber from landscape and cooling towers, wooden silos, hop-poles, cable drums and wooden playground equipment. These waste streams sum up to several 100,000 tons of material per year currently to be dumped in every major country of the European Community (EC). Technologies need to be developed to reduce this CCA treated wood waste, such that all of the metals are contained in a marketable product stream, and the pyrolysis gases and/or pyrolysis liquid are used to their maximum potential with respect to energy recuperation. Pyrolysing the CCA treated wood waste may be a good solution to the growing disposal problem since low temperatures and no oxidising agents are used, which result in lower loss of metals compared to combustion. An experimental labscale pyrolysis system has been developed to study the influence of the pyrolysis temperature and the duration of the pyrolysis process on the release of metals and the mass reduction. The macrodistribution and microdistribution of the metals in the solid pyrolysis residue is studied using Inductively Coupled Plasma Mass Spectrometry (ICP–MS) and Scanning Electron Microscopy coupled with Energy Dispersive X-ray Analysis (SEM–EDXA). Furthermore, a complete mass balance is calculated over the pyrolysis system. Based on these results a semi-industrial pyrolysis system (pilot plant scale) has been developed consisting of three stages: grinding, packed bed pyrolysis and metal separation. Special types of equipment have been developed to carry out the three stages. A new grinding system has been developed, based on a crushing mechanism rather than a cutting mechanism. The crushed wood is introduced by means of a screw feeding system into a reaction column. In this pyrolysis reactor the wood is heated by subjecting it to a flow of hot gases. This causes an adiabatic pyrolysis, which results in volatilisation of the volatile compounds whereas the mineral compounds (containing the metals) remain entrapped in a coal-type residue which is very rich in carbon. The condensable compounds in the pyrolysis gas condense while leaving the reaction zone due to the inverse temperature gradient. The pyrolysis gas leaving the reactor is used as fuel for the hot gas generator. The charcoal which is extracted at the bottom of the reactor, is cooled, compressed, removed and stored, ready to feed the subsequent stage. A specially developed grinder is used to remove the metal particles from the charcoal and the separation between metal and charcoal particles is accomplished in a pneumatic centrifuge as a result of the difference in density. Using this system the ultimate waste is less than 3% of the initial wood mass. Results obtained with a semi-industrial scale prototype confirm the effectiveness of the process.     

A new method for evaluating the sewage sludge pyrolysis kinetics

A new method to simplify calculation the kinetics model is applied to sewage sludge pyrolysis based on the assumption that volatile run out as soon as it formed and during temperature arising process in this study. Difference method widely used to solve math problems is conducted to calculate kinetics parameters. Pyrolysis experiments are carried out at heating rates of 10, 15, 20, and 50 °C/min. All the TG curves are divided into three parts which are beginning decomposition temperature range, main decomposition temperature range, and final decomposition temperature range. The second one is employed to determine the parameters for more than 70% of the total mass loss occurs in this range. According to the developed method, the react order, reaction energy and pre-exponential factor are obtained, which are in the range of 3.9–4.1, 82.3–109.2 kJ/mol and 7.7 × 10⁶–2.8 × 10⁹/min, respectively, which are in the range of that reported previously. As a comparison experimental data with calculated data, the well fitting results indicate that this method is appropriate for simulating sludge pyrolysis kinetics.     

TG/FTIR analysis on co-pyrolysis behavior of PE,PVC and PS

The pyrolysis and co-pyrolysis behaviors of polyethylene (PE), polystyrene (PS) and polyvinyl chloride (PVC) under N₂ atmosphere were analyzed by Thermal gravimetric/Fourier transform infrared (TG/FTIR). The volatile products were analyzed to investigate the interaction of the plastic blends during the thermal decomposition process. The TGA results showed that the thermal stability increased followed by PVC, PS and PE. The pyrolysis process of PE was enhanced when mixed with PS. However, PS was postponed when mixed with PVC. As for PE and PVC, mutual block was happened when mixed together. The FTIR results showed that the free radical of the decomposition could combine into a stable compound. When PE mixed with PVC or PS, large amount of unsaturated hydrocarbon groups existed in products while the content of alkynes was decreased. The methyl (CH₃) and methylene (CH₂) bonds were disappeared while PVC mixed with PE.     

Quality improvement of pyrolysis oil from waste rubber by adding sawdust

This work was aimed at improving the pyrolysis oil quality of waste rubber by adding larch sawdust. Using a 1 kg/h stainless pyrolysis reactor, the contents of sawdust in rubber were gradually increased from 0%, 50%, 100% and 200% (wt%) during the pyrolysis process. Using a thermo-gravimetric (TG) analyzer coupled with Fourier transform infrared (FTIR) analysis of evolving products (TG–FTIR), the weight loss characteristics of the heat under different mixtures of sawdust/rubber were observed. Using the pyrolysis–gas chromatography (GC)–mass spectrometry (Py–GC/MS), the vapors from the pyrolysis processes were collected and the compositions of the vapors were examined. During the pyrolysis process, the recovery of the pyrolysis gas and its composition were measured in-situ at a reaction temperature of 450 °C and a retaining time of 1.2 s. The results indicated that the efficiency of pyrolysis was increased and the residual carbon was reduced as the percentage of sawdust increased. The adding of sawdust significantly improved the pyrolysis oil quality by reducing the polycyclic aromatic hydrocarbons (PAHs) and nitrogen and sulfur compounds contents, resulting in an improvement in the combustion efficiency of the pyrolysis oil.     

Petrogenetic characteristics of molten slag from the pyrolysis/melting treatment of MSW

MSW slag materials derived from four pyrolysis melting plants in Japan were studied from the viewpoint of petrology in order to discriminate the glass and mineral phases and to propose a petrogenetic model for the formation process of molten slag. Slag material is composed of two major components: melt and refractory products. The melt products that formed during the melting process comprise silicate glass, and a suite of minerals as major constituents. The silicate glass is essentially composed of low and high silica glass members (typically 30% and 50% of SiO(2), respectively), from which minerals such as spinels, melilite, pseudowollastonite, and metallic inclusions have been precipitated. The refractory products consist mainly of pieces of metals, minerals and lithic fragments that survived through the melting process. Investigations demonstrated that the low silica melts (higher Ca and Al contents) were produced at upper levels of high temperature combustion chamber HTCC, at narrower temperature ranges (1250-1350 degrees C), while the high silica melts formed at broader temperature ranges (1250-1450 degrees C), at the lower levels of HTCC. The recent temperature ranges were estimated by using CaOAl(2)O(3)SiO(2) (CAS) ternary liquidus diagram that are reasonably consistent with those reported for a typical combustor. It was also understood that the samples with a higher CaO/SiO(2) ratio (>0.74-0.75) have undergone improved melting, incipient crystallization of minerals, and extensive homogenization. The combined mineralogical and geochemical examinations provided evidence to accept the concept of stepwise generation of different melt phases within the HTCC. The petrogenesis of the melt products may therefore be described as a two-phase melt system with immiscible characteristics that have been successively generated during the melting process of MSW.     

Kinetics of peanut shell pyrolysis and hydrolysis in subcritical water

Biomass is recognized as an important solution to energy and the environmental problems related to fossil fuel usage. The rational utilization of biomass waste is important not only for the prevention of environmental issues, but also for the effective utilization of natural resources. Pyrolysis and hyrolysis in subcritical water are promising processes for biomass waste conversion. This paper deals with hydrolysis and pyrolysis of peanut shells. Hydrolysis and pyrolysis kinetics of peanut shell wastes were investigated for the in-depth exploration of process mechanisms and for the control of the reactions. Hydrolysis kinetics was conducted in a temperature range of 180–240 °C. A simplified kinetic model to describe the hydrolysis of peanut shells was proposed. Hydrolysis activation energy as well as the pre-exponential factor was determined according to the model. The target products of peanut shell hydrolysis, reducing sugars, can reach up to 40.5 % (maximum yield) at 220 °C and 180 s. Pyrolysis characteristics were investigated. The results showed that three stages appeared in this thermal degradation process. Kinetic parameters in terms of apparent pyrolysis activation energy and pre-exponential factor were obtained by the Coats–Redfern method.