Methods for household waste composition studies

The question is how to conduct household waste composition studies. The review is divided into three parts: overview of known methods, sampling theory, and the waste components. Twenty methods are listed and commented on. There is no adopted, working international standard. In accordance with Pierre Gy's Theory of Sampling, the seven types of sampling errors, when collecting and splitting solid samples, are described and commented on in relation to sampling of household solid waste. It is concluded that the most crucial choices in household waste composition studies are: to divide the investigation into relevant number and types of strata; to decide the required sample size and number of samples; to choose the sampling location, i.e., sampling at household level or sampling from loads of waste collection vehicles; and to choose the type and number of waste component categories to be investigated. Various classifications of household waste components used in composition studies are listed and discussed. Difficulties and weaknesses of the reviewed methods are discussed and concluded in suggested questions for further research.     

Proximate composition of household waste and applicability of waste management technologies by source separation in Hanoi,Vietnam

The organic fraction of municipal solid wastes in Southeast Asia, which has a high moisture content, accounts for a large proportion of total waste. Local governments need to pay adequate attention to the composition of wastes to determine alternative waste management technologies. This study proposed the use of a triangle diagram to describe changes in proximate composition and rates of successful source separation of municipal solid waste and to identify technical challenges about alternative waste management technologies such as incineration, composting, and refuse-derived fuel production based on physical and proximate composition analysis of household waste sampled in Hanoi, Vietnam, as a case study. The analysis indicated the effectiveness of different types of source separation as well as different levels of successful achievement of source separation as an adjustment mechanism for the proximate composition of waste. Proper categorization of wastes for source separation is necessary for the appropriate use of alternative waste management technologies. The results showed that, at a source separation rate of just greater than 0.52 in a three-way separation scheme, the waste separated as combustible waste would be suitable for incineration with energy recovery. Based on well-designed schemes of source separation, alternative waste management technologies can be applied.     

Chemical composition of material fractions in Danish household waste

The chemical composition of Danish household waste was determined by two approaches: a direct method where the chemical composition (61 substances) of 48 material fractions was determined after hand sorting of about 20 tonnes of waste collected from 2200 households; and an indirect method where batches of 80–1200 tonnes of unsorted household waste was incinerated and the content of the waste determined from the content of the outputs from the incinerator. The indirect method is believed to better represent the small but highly contaminated material fractions (e.g., batteries) than the direct method, because of the larger quantities included and the more homogenous material to sample from. Differences between the direct and the direct methods led to corrections in the of heavy metal concentration of a few fractions.The majority of the energy content of the waste originates from organic waste like paper, cardboard and organic fractions. The single fraction contributing most to the total energy content is the non-recyclable plastic fraction, contributing 21% of the energy content and 60% of the chlorine content, although this fraction comprises less than 7% by weight. Heavy metals originate mainly from inert fractions, primarily batteries.     

Factors influencing household waste management practices in Zimbabwe

Journal of Material Cycles and Waste Management - The management of household solid waste is a growing concern related to public health and environmental damage. The study examined...     

Discussion on the methodology for determining food waste in household waste composition studies

Food waste has become an increasingly discussed topic in recent years. However, there is little authoritative data on food waste quantities and composition and systematic and comparable data are missing. Household waste composition analyses, which are often carried out routinely at regular or irregular intervals, provide an opportunity for obtaining data about food waste at both local and regional levels. The results of prior waste composition studies are not really comparable due to the different classifications, definitions and methods used; in addition, these are mostly insufficiently described and not reproducible by a third party. The aim of this paper is to discuss a methodology for determining the proportion of food waste in household waste composition studies, by analysing specific problems and possible solutions. For that purpose, findings from the literature are analysed and the approach and results of a composition analysis of residual waste of a stratified sample (urban, rural area) are presented. The study suggests that in order to avoid a significant loss of information, waste should not be sieved before sorting and packed food waste should be classified into the relevant food waste category together with its packaging. The case study showed that the overall influence of the proportion of food packaging included in the food waste category, which amounted to only 8%, did not significantly influence the results and can therefore be disregarded.     

Sampling method to determine a household waste composition variance

Knowledge of waste composition is of crucial importance for waste management forecasting. Composition is usually specified by average content of glass, paper, organic matter etc. In this paper a sorting method and its application to variance determination is described. A variation coefficient and a confidence interval are then calculated. From these two parameters an appreciation of the dispersion and the uncertainty associated with the mean values can be derived. In the case studied, the variation coefficients calculated were between 0.10 and 0.50 depending on the class of waste. Analysis of confidence intervals shows that reliability is good for low-abundance components such as, for example, aluminium, iron and plastics. The influence of practical constraints on the theoretical guidelines is also discussed.     

Consumer perspectives on household hazardous waste management in Japan

We give an overview of the management systems of household hazardous waste (HHW) in Japan and discuss the management systems and their risks. To get basic information, we conducted a survey of consumers to discover their behavior and awareness of HHW items throughout the entire life cycle, which is made up of the purchase, use, and disposal of a product. The results showed that many people hold end-of-life batteries, fluorescent lamps, empty spray cans, and others in their houses after use. Also, the results showed that a lot of such waste items were discarded in waste streams different from those stipulated by local governments. In particular, many people do not remove NiCd batteries inside products such as shavers or cordless phones before discarding. On the other hand, people’s knowledge of and concern regarding the risks, collection, and recycling of HHW were high. When information about the risks was specifically presented in the questionnaire, people tended to show a more positive intention to participate in a collection and recycling system compared to those who were not presented with such information. Our studies on NiCd batteries and fluorescent lamps showed that it is important to collect and recycle HHW to control the domestic and international flows of cadmium and mercury.     

Participatory approach, acceptability and transparency of waste management LCAs: case studies of Torino and Cuneo

The paper summarises the main results obtained from two extensive applications of Life Cycle Assessment (LCA) to the integrated municipal solid waste management systems of Torino and Cuneo Districts in northern Italy. Scenarios with substantial differences in terms of amount of waste, percentage of separate collection and options for the disposal of residual waste are used to discuss the credibility and acceptability of the LCA results, which are adversely affected by the large influence of methodological assumptions and the local socio-economic constraints. The use of site-specific data on full scale waste treatment facilities and the adoption of a participatory approach for the definition of the most sensible LCA assumptions are used to assist local public administrators and stakeholders showing them that LCA can be operational to waste management at local scale.     

LCA for household waste management when planning a new urban settlement

When planning for a new urban settlement, industrial ecology tools like scenario building and life cycle assessment can be used to assess the environmental quality of different infrastructure solutions. In Trondheim, a new greenfield settlement with carbon-neutral ambitions is being planned and five different scenarios for the waste management system of the new settlement have been compared. The results show small differences among the scenarios, however, some benefits from increased source separation of paper and metal could be found. The settlement should connect to the existing waste management system of the city, and not resort to decentralised waste treatment or recovery methods. However, as this is an urban development project with ambitious goals for lifestyle changes, effort should be put into research and initiatives for proactive waste prevention and reuse issues.     

Characterization of household waste in Greenland

The composition of household waste in Greenland was investigated for the first time. About 2 tonnes of household waste was sampled as every 7th bag collected during 1 week along the scheduled collection routes in Sisimiut, the second largest town in Greenland with about 5400 inhabitants. The collection bags were sorted manually into 10 material fractions. The household waste composition consisted primarily of biowaste (43%) and the combustible fraction (30%), including anything combustible that did not belong to other clean fractions as paper, cardboard and plastic. Paper (8%) (dominated by magazine type paper) and glass (7%) were other important material fractions of the household waste. The remaining approximately 10% constituted of steel (1.5%), aluminum (0.5%), plastic (2.4%), wood (1.0%), non-combustible waste (1.8%) and household hazardous waste (1.2%). The high content of biowaste and the low content of paper make Greenlandic waste much different from Danish household waste. The moisture content, calorific value and chemical composition (55 elements, of which 22 were below detection limits) were determined for each material fraction. These characteristics were similar to what has been found for material fractions in Danish household waste. The chemical composition and the calorific value of the plastic fraction revealed that this fraction was not clean but contained a lot of biowaste. The established waste composition is useful in assessing alternative waste management schemes for household waste in Greenland.     

Controlled combustion tests and bottom ash analysis using household waste with varying composition

The influence of the co-combustion of household waste with either sewage sludge, shredder fluff, electronic and electrical waste (WEEE) or PVC on the bottom ash quality and content was investigated under controlled laboratory conditions using a pot furnace. This laboratory approach avoids the interpretation problems related to large variations in input waste composition and combustion conditions that are observed in large scale MSW incinerators. The data for metals content, transfer coefficients and leaching values are presented relative to data for a base household waste composition that did not contain any of the added special wastes. The small WEEE invited direct measurement of precious metals content in the ashes, where measurement accuracy is facilitated by using only mobile phone scrap for small WEEE. The analyses were carried out for different particle size ranges that are of relevance to the recyclability of metals and minerals in the ashes. Positive correlations were found between elements content of the input waste and the bottom ashes, and also between increased levels of Cl, Mo and Cu in the input waste and their leaching in the bottom ashes. These correlations indicate that addition of PVC, small WEEE and shredder fluff in input waste can have a negative influence on the quality of the bottom ashes. Enrichment of Au and Ag occurred in the fractions between 0.15 and 6 mm. The precious metals content represents an economically interesting intrinsic value, even when the observed peak values are properly averaged over a larger volume of ashes. Overall, it has been shown that changes in quality and content of bottom ashes may be traced back to the varied input waste composition.     

Inconsistent pathways of household waste

The aim of this study was to provide policy-makers and waste management planners with information about how recycling programs affect the quantities of specific materials recycled and disposed of. Two questions were addressed: which factors influence household waste generation and pathways? and how reliable are official waste data? Household waste flows were studied in 35 Swedish municipalities, and a wide variation in the amount of waste per capita was observed. When evaluating the effect of different waste collection policies, it was found to be important to identify site-specific factors influencing waste generation. Eleven municipal variables were investigated in an attempt to explain the variation. The amount of household waste per resident was higher in populous municipalities and when net commuting was positive. Property-close collection of dry recyclables led to increased delivery of sorted metal, plastic and paper packaging. No difference was seen in the amount of separated recyclables per capita when weight-based billing for the collection of residual waste was applied, but the amount of residual waste was lower. Sixteen sources of error in official waste statistics were identified and the results of the study emphasize the importance of reliable waste generation and composition data to underpin waste management policies.     

Fish and shrimp waste management at household and market in Bushehr,Iran

Journal of Material Cycles and Waste Management - The aim of this study was to investigate the estimation and management of fish and shrimp wastes in Bushehr province. Two-part questionnaire...     

A multiple criteria analysis for household solid waste management in the urban community of Dakar

Household solid waste management is a severe problem in big cities of developing countries. Mismanaged solid waste dumpsites produce bad sanitary, ecological and economic consequences for the whole population, especially for the poorest urban inhabitants. Dealing with this problem, this paper utilizes field data collected in the urban community of Dakar, in view of ranking nine areas of the city with respect to multiple criteria of nuisance. Nine criteria are built and organized in three families that represent three classical viewpoints: the production of wastes, their collection and their treatment. Thanks to the method PROMETHEE and the software ARGOS, we do a pair-wise comparison of the nine areas, which allows their multiple criteria rankings according to each viewpoint and then globally. Finding the worst and best areas in terms of nuisance for a better waste management in the city is our final purpose, fitting as well as possible the needs of the urban community. Based on field knowledge and on the literature, we suggest applying general and area-specific remedies to the household solid waste problems.     

The use of chemical composition data in waste management planning--a case study

As the waste industry continues to move from a disposal-based system to one based on a combination of recovery options, the need for information on the composition of waste increases and this is reflected by the amount of information on the physical composition of municipal solid wastes that is now available. However, there is far less information on the chemical composition of municipal solid waste. The results from a number of chemical surveys from Europe are compared and show a reasonable degree of agreement, but several problems were identified with the data. Chemical and physical compositional data are combined in a case study example to investigate the flow of key potential pollutants in an integrated solid waste management system that uses materials recycling, composting, incineration and landfilling. This case study has shown that an integrated waste management strategy diverts lead and cadmium away from composting and recycling to incineration, which effectively isolates these elements from the environment through efficient capture of the pollutants followed by secure landfilling or recycling of the residues. However, further work is needed to determine the distribution of mercury in incineration residues and its fate when the residues are landfilled.     

上海市餐厨垃圾管理处置现状及建议

结合日常管理工作,梳理了从餐厨垃圾的源头申报、中途收运到末端处置过程中存在的主要问题,如申报量不足、挂靠收运、执法难等,分析了这些问题影响管理推进的主要原因,并从政府管理资源、政策扶持、标准制定、规划布局等方面提出一些建议。     

Municipal solid waste composition determination supporting the integrated solid waste management system in the island of Crete

A one-year survey was conducted in the greater region of Crete (located at the lower region of the Aegean Sea) for the purpose of identifying waste composition (including chemical and physical characterization), as well as any seasonal variation. The investigation was carried out repeatedly at seven landfills and one transfer station in Crete, in four phases. Each sampling phase corresponded to a season (autumn, winter, spring, summer). ASTM D5231-92(2003) standard method and RCRA Waste Sampling Draft Technical Guidance were used. Hand sorting was used for classifying the collected wastes into the following categories: plastics, paper, metals, aluminium, leather-wood-textiles-rubbers, organic wastes, non-combustibles and miscellaneous. Further analysis included proximate and ultimate analysis of combustible materials. Metals such as lead, cadmium and mercury were also investigated. The results show that there has been a significant decrease of organic wastes during the last decade due to the increase of packaging materials, as a result of a change in consumption patterns. Three main waste categories were determined: organic wastes, paper and plastics, which combined represent 76% of the total waste in Crete. Furthermore, a high fraction of glass and a seasonal variation of aluminium indicate a strong correlation of waste composition with certain human activities, such as tourism. There is also a variation between the municipal solid waste (MSW) composition in the region of Crete (2003-2004) and MSW composition suggested in the National Solid Waste Planning (2000) [National Solid Waste Planning, 2000. Completion and particularization of Common Ministerial Act 113944//1944/1997: National Solid Waste Planning, June 2000]. The results of this survey are to be utilized by the regional solid waste authorities in order to establish an integrated waste treatment site, capable of fulfilling the regional waste management demands.     

Assessment of factors affecting household solid waste generation and its composition in Gulberg Town,Lahore, Pakistan

This paper analyzes and compares the findings of the characterization study of collected solid waste from households of three different socioeconomic groups in Lahore, Pakistan, over the four seasons, i.e. Spring (March–April, 2008), Summer (May–June, 2008), Monsoon (August–September, 2008) and Winter (December 2008 and January 2009). The generation rate of waste was 0.96 kg/cap/day for high-income, 0.73 kg/cap/day for middle and 0.67 kg/cap/day for low-income group. The average of total household solid waste (HSW) generation is 0.79 kg/cap/day (including 0.75 kg/cap/day for spring, 0.77 kg/cap/day for summer, 0.86 kg/cap/day for monsoon and 0.76 kg/cap/day. The breakdown for the major physical components of the waste shows that organic waste accounts for the largest proportion (67.46 %). The relations between waste generation rates by physical category and subcategory, in addition to factors such as socioeconomic groups (population density levels, household income and household size), seasonal variation, and daily variation (difference of HSW generation among days of a week) were also analyzed. Statistical analysis shows that there was no significant difference in overall waste generation among days of a week. A significant difference between the seasons for food waste, cardboard, PET, HDPE, other hazardous waste, battery cells, and dust and stone (p < 0.001) was found. The generation rates were found to be higher when compared to other developing countries.     

A charge model for household waste management services: a case study of Tehran municipality

In practice, it is difficult to implement Pay-As-You-Throw charge systems based on accurate estimates of waste generation. In many cities, this is made impossible, due to lack of technical and administrative infrastructure and cultural considerations, especially in developing countries. This paper presents an alternative two-component charge model that is the combination of cost-accounting technique of Waste Management Services (WMSs) and econometric functions of waste generation. Practical and computation steps considered by the model are presented as a proposal to reform the current system of waste charge in Tehran municipality. The presented model is simple to implement and resolves some of the disadvantages of the traditional methods of waste charge systems, including insufficient revenue to cover the cost of waste management and unfairness related to social inequality.