Determination of renewable energy yield from mixed waste material from the use of novel image analysis methods

Two novel techniques are presented in this study which together aim to provide a system able to determine the renewable energy potential of mixed waste materials. An image analysis tool was applied to two waste samples prepared using known quantities of source-segregated recyclable materials. The technique was used to determine the composition of the wastes, where through the use of waste component properties the biogenic content of the samples was calculated. The percentage renewable energy determined by image analysis for each sample was accurate to within 5% of the actual values calculated. Microwave-based multiple-point imaging (AutoHarvest) was used to demonstrate the ability of such a technique to determine the moisture content of mixed samples. This proof-of-concept experiment was shown to produce moisture measurement accurate to within 10%. Overall, the image analysis tool was able to determine the renewable energy potential of the mixed samples, and the AutoHarvest should enable the net calorific value calculations through the provision of moisture content measurements. The proposed system is suitable for combustion facilities, and enables the operator to understand the renewable energy potential of the waste prior to combustion.     

CO₂ emission factors for waste incineration: Influence from source separation of recyclable materials

CO₂-loads from combustible waste are important inputs for national CO₂ inventories and life-cycle assessments (LCA). CO₂ emissions from waste incinerators are often expressed by emission factors in kg fossil CO₂ emitted per GJ energy content of the waste. Various studies have shown considerable variations between emission factors for different incinerators, but the background for these variations has not been thoroughly examined. One important reason may be variations in collection of recyclable materials as source separation alters the composition of the residual waste incinerated. The objective of this study was to quantify the importance of source separation for determination of emission factors for incineration of residual household waste. This was done by mimicking various source separation scenarios and based on waste composition data calculating resulting emission factors for residual waste routed to incineration. Emission factors ranged from 27 to 40 kg CO₂/GJ. The results appeared most sensitive towards variations in waste composition and water content. Recycling rates and lower heating values could not be used as simple indicators of the resulting emission factors for residual household waste; however the fossil carbon ratio of the waste after source separation was found to be appropriately correlated with the emission factor. Based on the results, it is recommended to carefully evaluate the source separation and collection systems behind reported literature values when comparing different studies and when using the values for environmental assessment purposes.     

Effect of mixing ratio of woody waste and food waste on the characteristics of carbonization residue

Biomass such as woody waste and food waste can be converted to a renewable energy source by means of carbonization processes. The basic characteristics of woody waste and food waste, such as proximate analysis and heating value, were evaluated before carrying out carbonization tests. Carbonization tests were carried out to obtain the basic characteristics of carbonization residue on changing the proportion of food waste from 0% to 30% in the mixture of woody waste and food waste. The effect of the food waste was estimated by basic characteristics of the residue such as the heating value, yield, and fuel ratio. As increased the food waste content, the bulk density, yield and chlorine content of the carbonization residue increased, but fuel ratio, the carbon content and heating value of the residue decreased. From the results of the basic characteristics of the residue, the optimum food waste content in carbonization tests was found to be 20%. Even if food waste is combined with woody waste at levels up to 30%, the sulfur and chlorine concentrations in the residue were much lower than the regulatory standard levels. From the results for the fuel ratio and heating value of the residue, the carbonization residue is suitable for use as a renewable energy source and can be categorized by the second grade level of solid fuel products.     

Source separation of household waste: a case study in China

A pilot program concerning source separation of household waste was launched in Hangzhou, capital city of Zhejiang province, China. Detailed investigations on the composition and properties of household waste in the experimental communities revealed that high water content and high percentage of food waste are the main limiting factors in the recovery of recyclables, especially paper from household waste, and the main contributors to the high cost and low efficiency of waste disposal. On the basis of the investigation, a novel source separation method, according to which household waste was classified as food waste, dry waste and harmful waste, was proposed and performed in four selected communities. In addition, a corresponding household waste management system that involves all stakeholders, a recovery system and a mechanical dehydration system for food waste were constituted to promote source separation activity. Performances and the questionnaire survey results showed that the active support and investment of a real estate company and a community residential committee play important roles in enhancing public participation and awareness of the importance of waste source separation. In comparison with the conventional mixed collection and transportation system of household waste, the established source separation and management system is cost-effective. It could be extended to the entire city and used by other cities in China as a source of reference.     

The use of commercial and industrial waste in energy recovery systems - A UK preliminary study

With 2020 energy targets set out by the EU fast approaching, the UK is trying to source a higher proportion of its energy from renewable resources. Coupled with this, a growing population and increasing trends in consumer demand have resulted in national waste loads increasing. A possible solution to both issues is energy-from-waste (EfW) technologies. Many studies have focused on municipal solid waste (MSW) as a potential feedstock, but appear to overlook the potential benefits of commercial and industrial waste (C&IW). In this study, samples of C&IW were collected from three North West waste management companies and Lancaster University campus. The samples were tested for their gross and net calorific value, moisture content, ash content, volatile matter, and also elemental composition to determine their suitability in EfW systems. Intra-sample analysis showed there to be little variation between samples with the exception two samples, from waste management site 3, which showed extensive variation with regards to net calorific value, ash content, and elemental analysis. Comparisons with known fuel types revealed similarities between the sampled C&IW, MSW, and refuse derived fuel (RDF) thereby justifying its potential for use in EfW systems. Mean net calorific value (NCV) was calculated as 9.47 MJ/kg and concentrations of sulphur, nitrogen, and chlorine were found to be below 2%. Potential electrical output was calculated using the NCV of the sampled C&IW coupled with four differing energy generation technologies. Using a conventional incinerator with steam cycle, total electrical output was calculated as 24.9 GWh, based on a plant operating at 100,000 tpa. This value rose to 27.0 GWh when using an integrated gasification combined cycle. A final aspect of this study was to deduce the potential total national electrical output if all suitable C&IW were to be used in EfW systems. Using incineration coupled with a steam turbine, this was determined to be 6 TWh, 1.9% of the national demand thereby contributing 6.5% towards the UK’s 2020 renewable electricity target.     

Biodegradable municipal solid waste: characterization and potential use as animal feedstuffs

Five different fractions of the biodegradable municipal solid waste (BMSW) were evaluated as potential animal feedstuffs. For each source of waste (meat waste (MW), fish waste (FW), fruit and vegetables waste (FVW), restaurant waste (RW), household waste (HW)), samples were obtained from small shops (butchers, fishmongers, fruit and vegetable shops), restaurants and a MSW treatment plant (household waste). The chemical composition, microbiological characterization, dioxins, furans, PCB's and mineral content were determined for every type of waste fraction. The analysed biodegradable waste presented high moisture content (from 60% to 90%). Some fractions were dense in one nutrient: meat waste in ether extract, fish waste in crude protein, fruit and vegetable waste in nitrogen free extract. The other studied fractions (restaurant fraction and household fraction) presented a more balanced composition, but the presence of toxic concentrations of contaminants such as metals was higher than European legislation permitted values in animal feeding. From a microbiological standpoint, a heat treatment at 65 degrees C for 20 min was sufficient to ensure microbiological quality of the samples. This treatment was also advisable to reduce the moisture content: a lower moisture content facilitates the waste handling and processing and, therefore, the inclusion of these waste fractions in commercial animal diets. This paper presents a potential alternative for the recovery of organic matter content in municipal solid waste. The results obtained in this research and the feedstuffs legislation in force related to animal feed, indicated that some of the studied biodegradable waste fractions (meat waste, fruit and vegetable waste and fish waste) could be considered as alternatives to typical raw materials used in animal feeds.     

Proximate composition of household waste and applicability of waste management technologies by source separation in Hanoi,Vietnam

The organic fraction of municipal solid wastes in Southeast Asia, which has a high moisture content, accounts for a large proportion of total waste. Local governments need to pay adequate attention to the composition of wastes to determine alternative waste management technologies. This study proposed the use of a triangle diagram to describe changes in proximate composition and rates of successful source separation of municipal solid waste and to identify technical challenges about alternative waste management technologies such as incineration, composting, and refuse-derived fuel production based on physical and proximate composition analysis of household waste sampled in Hanoi, Vietnam, as a case study. The analysis indicated the effectiveness of different types of source separation as well as different levels of successful achievement of source separation as an adjustment mechanism for the proximate composition of waste. Proper categorization of wastes for source separation is necessary for the appropriate use of alternative waste management technologies. The results showed that, at a source separation rate of just greater than 0.52 in a three-way separation scheme, the waste separated as combustible waste would be suitable for incineration with energy recovery. Based on well-designed schemes of source separation, alternative waste management technologies can be applied.     

Bio-drying and size sorting of municipal solid waste with high water content for improving energy recovery

Bio-drying can enhance the sortability and heating value of municipal solid waste (MSW), consequently improving energy recovery. Bio-drying followed by size sorting was adopted for MSW with high water content to improve its combustibility and reduce potential environmental pollution during the follow-up incineration. The effects of bio-drying and waste particle size on heating values, acid gas and heavy metal emission potential were investigated. The results show that, the water content of MSW decreased from 73.0% to 48.3% after bio-drying, whereas its lower heating value (LHV) increased by 157%. The heavy metal concentrations increased by around 60% due to the loss of dry materials mainly resulting from biodegradation of food residues. The bio-dried waste fractions with particle size higher than 45 mm were mainly composed of plastics and papers, and were preferable for the production of refuse derived fuel (RDF) in view of higher LHV as well as lower heavy metal concentration and emission. However, due to the higher chlorine content and HCl emission potential, attention should be paid to acid gas and dioxin pollution control. Although LHVs of the waste fractions with size <45 mm increased by around 2× after bio-drying, they were still below the quality standards for RDF and much higher heavy metal pollution potential was observed. Different incineration strategies could be adopted for different particle size fractions of MSW, regarding to their combustibility and pollution property.     

Chemical composition of material fractions in Danish household waste

The chemical composition of Danish household waste was determined by two approaches: a direct method where the chemical composition (61 substances) of 48 material fractions was determined after hand sorting of about 20 tonnes of waste collected from 2200 households; and an indirect method where batches of 80–1200 tonnes of unsorted household waste was incinerated and the content of the waste determined from the content of the outputs from the incinerator. The indirect method is believed to better represent the small but highly contaminated material fractions (e.g., batteries) than the direct method, because of the larger quantities included and the more homogenous material to sample from. Differences between the direct and the direct methods led to corrections in the of heavy metal concentration of a few fractions.The majority of the energy content of the waste originates from organic waste like paper, cardboard and organic fractions. The single fraction contributing most to the total energy content is the non-recyclable plastic fraction, contributing 21% of the energy content and 60% of the chlorine content, although this fraction comprises less than 7% by weight. Heavy metals originate mainly from inert fractions, primarily batteries.     

Pretreatment of municipal solid waste prior to landfilling

An outdoor pilot-scale study was undertaken to pretreat municipal solid waste by windrow composting. The raw waste was introduced to active composting without any source separation or pulverization. Pretreatment indicators were developed and used as a tool to measure the optimum level of sorting and waste stabilization. The moisture content of the waste dropped from 68% to 61% and the pile attained a thermophilic temperature in one week. It was observed that the C/N ratio, pH profile and temperature gradients were comparable to that of traditional windrow composting. Within one week of active bulk composting, the easily degradable organic matter was consumed and there was a significant reduction in the bulk volume of the mixed waste. The pre-composted wastes were then sorted into four fractions. Compared to the initial untreated waste, the pretreated waste showed greater sorting efficiency and reduced volatile solids. A 1-m³ cage was used to study pile settlement and volume reduction. The results indicate that pretreatment by bulk composting could reduce by ≈40% the total mass of waste hauled to landfill sites in developing countries.     

Characterization of household waste in Greenland

The composition of household waste in Greenland was investigated for the first time. About 2 tonnes of household waste was sampled as every 7th bag collected during 1 week along the scheduled collection routes in Sisimiut, the second largest town in Greenland with about 5400 inhabitants. The collection bags were sorted manually into 10 material fractions. The household waste composition consisted primarily of biowaste (43%) and the combustible fraction (30%), including anything combustible that did not belong to other clean fractions as paper, cardboard and plastic. Paper (8%) (dominated by magazine type paper) and glass (7%) were other important material fractions of the household waste. The remaining approximately 10% constituted of steel (1.5%), aluminum (0.5%), plastic (2.4%), wood (1.0%), non-combustible waste (1.8%) and household hazardous waste (1.2%). The high content of biowaste and the low content of paper make Greenlandic waste much different from Danish household waste. The moisture content, calorific value and chemical composition (55 elements, of which 22 were below detection limits) were determined for each material fraction. These characteristics were similar to what has been found for material fractions in Danish household waste. The chemical composition and the calorific value of the plastic fraction revealed that this fraction was not clean but contained a lot of biowaste. The established waste composition is useful in assessing alternative waste management schemes for household waste in Greenland.     

Contribution to closing the loop on waste materials: valorization of bottom ash from waste-to-energy plants under a life cycle approach

Incineration has undergone several technology improvements, reducing air emissions and increasing the efficiency of energy and material recovery; however, there is still a long way to go. To analyze the environmental impacts of waste incineration, this study assessed 15 waste fractions that compose municipal waste in Spain, which are grouped as non-inert materials (plastics, paper, cardboard and organic matter), unburned materials (glass and Al) and ferrous materials. Additionally, this paper evaluates the valorization of bottom ash (BA) to produce steel, aluminum and cement in these recycled/recoverable waste fractions. The results depend on the input waste composition and the heating value (HHV) and showed that ferrous and unburned materials had the worst environmental performance due to the null HHV. The valorization of BA in steel, Al and cement production significantly reduced the environmental impact and the consumption of resources. BA recycling for secondary steel and Al production would improve the environmental performance of the combustion of unburned materials and ferrous materials, whereas the use of BA in cement production diminished the consumption of NR for non-inert materials. This is of great interest for organic matter and PC, waste with a low energy production and high heavy metal and sulfur content.     

Optimal utilization of waste-to-energy in an LCA perspective

Energy production from two types of municipal solid waste was evaluated using life cycle assessment (LCA): (1) mixed high calorific waste suitable for production of solid recovered fuels (SRF) and (2) source separated organic waste. For SRF, co-combustion was compared with mass burn incineration. For organic waste, anaerobic digestion (AD) was compared with mass burn incineration. In the case of mass burn incineration, incineration with and without energy recovery was modelled. Biogas produced from anaerobic digestion was evaluated for use both as transportation fuel and for heat and power production. All relevant consequences for energy and resource consumptions, emissions to air, water and soil, upstream processes and downstream processes were included in the LCA. Energy substitutions were considered with respect to two different energy systems: a present-day Danish system based on fossil fuels and a potential future system based on 100% renewable energy. It was found that mass burn incineration of SRF with energy recovery provided savings in all impact categories, but co-combustion was better with respect to Global Warming (GW). If all heat from incineration could be utilized, however, the two alternatives were comparable for SRF. For organic waste, mass burn incineration with energy recovery was preferable over anaerobic digestion in most impact categories. Waste composition and flue gas cleaning at co-combustion plants were critical for the environmental performance of SRF treatment, while the impacts related to utilization of the digestate were significant for the outcome of organic waste treatment. The conclusions were robust in a present-day as well as in a future energy system. This indicated that mass burn incineration with efficient energy recovery is a very environmentally competitive solution overall.     

Energy from waste: a possible alternative energy source for large size municipalities.

The net calorific values and weight composition of solid waste from all the major municipalities of the island of Cyprus were measured. Representative waste samples were collected, processed and tested for energy generation over a complete year. The energy values appear to vary from city to city depending on the season. The total energy that could be recovered from the waste amounted to approximately 8.5% of the total electricity generation of the island of Cyprus.     

A review of municipal solid waste composition and quantities in Poland

A review of results of the research involving the quantitative and composition analyses of household waste conducted in Poland in recent years is presented in this paper. For these analyses various methodologies have been employed, as there is not one obligatory methodology how to characterise municipal solid waste. The results of the research in large Polish cities indicate great variability, which is difficult to be reasonably explained. This situation is affected by a number of factors, such as various methods and places for sample collection, various methods for tests, fractional character of most of the studies (studies carried out only in some periods during a year). Consequently, it is neither possible to measurably compare their results, nor to generalise them. Hence, within this article only individual data for large cities is provided. It is therefore necessary to standardise methodology for such analyses in Europe, taking into account local variability (such as different housing patterns, climate and waste collection schemes) to allow comparison of results.Reported yearly household waste generation in Polish cities varies from 238 to 309 kg per inhabitant. Biodegradable waste is a strongly dominated fraction in household waste from Polish cities, followed by paper/cardboard and plastics. Historical data shows that waste composition has undergone profound changes, the most significant being an increase of the share of plastics and decrease of fine fraction. The presented data indicates that waste composition strongly depends on the type of housing and its heating system. In the new multi-family buildings with central heating the share of paper and plastics is higher than in old houses with individual heating. In the latter ones the share of fine fraction is higher.     

Selective collection as a pretreatment for indirect solid recovered fuel generation

Effective selective collection (SC) has been increasing in many countries of the European Union. As a consequence the composition of residual municipal solid waste (RMSW) is changing not only because of economic development, but also due to the collection system. The input of RMSW treatment plants is thus not homogeneous. This paper analyses two case studies involving a total of five SC scenarios and their impact on the generation of solid recovered fuel (SRF) with/without bio-drying, post-treatment and packaging take back programs (TBPs). These case studies are based on two types of SC: kerbside and drop-off. The latest regulation on SRF classification is taken into account: energy content, Cl and Hg concentrations are assessed and discussed. The role of the respirometric index (RI) is also analyzed. Results show that when SC is highly efficient RMSW can be classified directly as SRF, but only if the introduction of RI does not set stringent respirometric targets. The role of packaging TBPs is important as the residual waste remaining after the packaging has been processed, can be valorized increasing the lower heating value (LHV) of the residual RMSW and minimizing the streams that should be landfilled. The source separation of food waste has a significant impact on the suitability of bio-drying: when the SC of food waste is very efficient, its percentage in the RMSW may be too low for effective bio-drying.     

Long-term affected energy production of waste to energy technologies identified by use of energy system analysis

Affected energy production is often decisive for the outcome of consequential life-cycle assessments when comparing the potential environmental impact of products or services. Affected energy production is however difficult to determine. In this article the future long-term affected energy production is identified by use of energy system analysis. The focus is on different uses of waste for energy production. The Waste-to-Energy technologies analysed include co-combustion of coal and waste, anaerobic digestion and thermal gasification. The analysis is based on optimization of both investments and production of electricity, district heating and bio-fuel in a future possible energy system in 2025 in the countries of the Northern European electricity market (Denmark, Norway, Sweden, Finland and Germany). Scenarios with different CO₂ quota costs are analysed. It is demonstrated that the waste incineration continues to treat the largest amount of waste. Investments in new waste incineration capacity may, however, be superseded by investments in new Waste-to-Energy technologies, particularly those utilising sorted fractions such as organic waste and refuse derived fuel. The changed use of waste proves to always affect a combination of technologies. What is affected varies among the different Waste-to-Energy technologies and is furthermore dependent on the CO₂ quota costs and on the geographical scope. The necessity for investments in flexibility measures varies with the different technologies such as storage of heat and waste as well as expansion of district heating networks. Finally, inflexible technologies such as nuclear power plants are shown to be affected.     

Driving forces for import of waste for energy recovery in Sweden.

Between 1996 and 2002, the Swedish import of so-called yellow waste for energy recovery increased. The import mainly consisted of separated wood waste and mixes of used wood and paper and/or plastics that was combusted in district heat production plants (DHPPs). Some mixed waste was imported to waste incineration plants for energy recovery (10% of the import of yellow waste for energy recovery in 2002). The import came primarily from Germany, the Netherlands, Norway, Denmark and Finland. We identified six underlying driving forces for this recent increase of imported waste which are outlined and their interactive issues discussed. --The energy system infrastructure, which enables high energy recovery in Sweden. --The energy taxation, where high Swedish taxes on fossil fuels make relatively expensive solid biofuels the main alternative for base load production of district heat. --The quality of the waste-derived fuels, which has been higher in the exporting countries than in Sweden. --The bans on landfilling within Europe and the shortage of waste treatment capacity. --Taxes on waste management in Europe. --Gate fee differences between exporting countries and Sweden. In the future, the overall strength of these driving forces will probably be weakened. A Swedish tax on waste incineration is being investigated. In other European countries, the ambition to reach the Kyoto targets and increase the renewable electricity production could improve the competitiveness of waste-derived fuels in comparison with fossil fuels. Swedish DHPPs using waste-derived fuels will experience higher costs after the Waste Incineration Directive is fully implemented. The uncertainty about European waste generation and treatment capacity, however, might have a large influence on the future gate fees and thus also on the yellow waste import into Sweden.     

Environmental impact assessment of solid waste management in Beijing City, China

The environmental impacts of municipal solid waste management in Beijing City were evaluated using a life-cycle-based model, EASEWASTE, to take into account waste generation, collection, transportation, treatment/disposal technologies, and savings obtained by energy and material recovery. The current system, mainly involving the use of landfills, has manifested significant adverse environmental impacts caused by methane emissions from landfills and many other emissions from transfer stations. A short-term future scenario, where some of the landfills (which soon will reach their capacity because of rising amount of waste in Beijing City) are substituted by incinerators with energy recovery, would not result in significant environmental improvement. This is primarily because of the low calorific value of mixed waste, and it is likely that the incinerators would require significant amounts of auxiliary fuels to support combustion of wet waste. As for the long-term future scenario, efficient source separation of food waste could result in significant environmental improvements, primarily because of increase in calorific value of remaining waste incinerated with energy recovery. Sensitivity analysis emphasized the importance of efficient source separation of food waste, as well as the electricity recovery in incinerators, in order to obtain an environmentally friendly waste management system in Beijing City.     

Physico-chemical analysis and calorific values of poultry manure

Spain is one of the major producers of broilers and laying hens in the European Union, with an overall market share of around 12%. The poultry manure that is produced is usually employed as fertilizer on cropland, either directly or after a composting process. In some cases, however, this waste is transported over 120 km to be used as fertilizer, with the resulting high transport costs. In other countries, poultry manure is used as an alternative natural fuel source for power generation. In this study, poultry manure from all the laying hen farms in Asturias was characterized with a view to its possible use as an energy source. The Higher Heating Values on a dry basis (experimental) varies between 12,052 and 13,882 kJ/kg. Lower Heating Values (LHVs) on a wet basis range are much lower (mean values of 2664 kJ/kg) due to the high moisture content of poultry manure. Accordingly, the co-combustion of this waste with other types of waste such as forest and wood waste (LHV on a wet basis of 8044 and 15,830 kJ/kg, respectively) or municipal solid waste (LHV on a wet basis of 10,725 kJ/kg) should be considered as an alternative energy source. Chlorine and sulphur contents in dry matter vary around mean values of 0.64% and 0.11%, respectively. The waste also presents high amounts of Ca (4.84%) and K (2.38%).