Ozone artifacts and carbonyl measurements using Tenax GR, Tenax TA, Carbopack B, and Carbopack X adsorbents

Four popular thermally desorbable adsorbents used for air sampling (Tenax TA, Tenax GR, Carbopack B, and Carbopack X) are examined for the potential to form artifacts with ozone (O3) at environmental concentrations. The performance of these adsorbents for the ketone and aldehyde species identified as O3-adsorbent artifacts was also characterized, including recovery, linearity, and method detection limits (MDLs). Using gas chromatography/mass spectrometry, 13 different artifacts were identified and confirmed for both Tenax TA and Tenax GR, 9 for Carbopack B, but none for Carbopack X. Several O3 artifacts not reported previously were identified, including: pentanal, 3-hexanone, 2-hexanone, hexanal, 3-heptanone, and heptanal with Tenax TA; pentanal, 3-hexanone, 2-hexanone, hexanal, and 3-heptanone on Tenax GR; and 1-octene and 1-nonene with Carbopack B. Levels of straight-chain aldehyde artifacts rapidly diminished after a few cycles of adsorbent conditioning/O3 exposure, and concentrations could be predicted using a first-order model. Phenyl-substituted carbonyl artifacts (benzaldehyde and acetophenone) persisted on Tenax TA and GR even after 10 O3 exposure-conditioning cycles. O3 breakthrough through the adsorbent bed was most rapid in adsorbents that yielded the highest levels of artifacts. Overall, artifact composition and concentration are shown to depend on O3 concentration and dose, conditioning method, and adsorbent type and age. Calibrations showed good linearity, and most compounds had reasonable recoveries, for example, 90 +/- 15% for Tenax TA, 97 +/- 23% for Tenax GR, 101 +/- 24% for Carbopack B, and 79 +/- 25% (91 +/- 9% for n-aldehydes) for Carbopack X. Benzeneacetaldehyde recovery was notably poorer (22-63% across the four adsorbents). MDLs for several compounds were relatively high, up to 5 ng. By accounting for both artifact formation and method performance, this work helps to identify which carbonyl compounds can be measured using thermally desorbable adsorbents and which may be prone to bias because of the formation of O3-adsorbent artifacts.     

Ozone Artifacts and Carbonyl Measurements Using Tenax GR,Tenax TA,Carbopack B,and Carbopack X Adsorbents

Abstract

Four popular thermally desorbable adsorbents used for air sampling (Tenax TA, Tenax GR, Carbopack B, and Carbopack X) are examined for the potential to form artifacts with ozone (O₃) at environmental concentrations. The performance of these adsorbents for the ketone and alde-hyde species identified as O₃-adsorbent artifacts was also characterized, including recovery, linearity, and method detection limits (MDLs). Using gas chromatography/mass spectrometry, 13 different artifacts were identified and confirmed for both Tenax TA and Tenax GR, 9 for Carbopack B, but none for Carbopack X. Several O₃ artifacts not reported previously were identified, including: pentanal, 3-hexanone, 2-hexanone, hexanal, 3-heptanone, and heptanal with Tenax TA; pentanal, 3-hexanone, 2-hexanone, hexanal, and 3-heptanone on Tenax GR; and 1-octene and 1-nonene with Carbopack B. Levels of straight-chain aldehyde artifacts rapidly diminished after a few cycles of adsorbent conditioning/O₃ exposure, and concentrations could be predicted using a first-order model. Phenyl-substituted carbonyl artifacts (benzalde-hyde and acetophenone) persisted on Tenax TA and GR even after 10 O₃ exposure-conditioning cycles. O₃ breakthrough through the adsorbent bed was most rapid in adsorbents that yielded the highest levels of artifacts. Overall, artifact composition and concentration are shown to depend on O₃ concentration and dose, conditioning method, and adsorbent type and age. Calibrations showed good linearity, and most compounds had reasonable recoveries, for example, 90 ±15% for Tenax TA, 97 ±23% for Tenax GR, 101 ±24% for Carbopack B, and 79 ±25% (91 ±9% for n-aldehydes) for Carbopack X. Benzeneacetaldehyde recovery was notably poorer (22–63% across the four adsorbents). MDLs for several compounds were relatively high, up to 5 ng. By accounting for both artifact formation and method performance, this work helps to identify which carbonyl compounds can be measured using thermally desorbable adsorbents and which may be prone to bias because of the formation of O_3- adsorbent artifacts.     

Atmospheric contamination by pesticides: Determination in the liquid, gaseous and particulate phases

Between 1991 and 1993, 18 fogwater samples, 31 rainwater samples and 17 atmosphere (gas and particles) samples were analysed for 13 pesticides (pp’DDT,pp’DDD,pp’DDE, aldrin, dieldrin, lindane, hexachlorobenzene, fenpropathrin, mecoprop, methyl-parathion, atrazine, isoproturon and aldicarb). The samples were collected in a rural area where some of the compounds are in use (experimental INRA farm, “Institut National de la Recherche Agronomique” in Colmar, Eastern France, 80,000 inhabitants). This paper briefly presents the analytical methodology used and, in detail, the contamination level of the different atmospheric phases. The contamination levels are roughly constant throughout the year in all the atmospheric phases and the most abundant pesticides are those commonly used on the experimental INRA farm and other surrounding farms. Nevertheless, some pesticides not used since the 1970s such as 1,1-Bis(4-chlorophenyl)-2,2,2-trichloroethane (pp’DDT) and 2,2-Bis(4-chlorophenyl)-1,1-dichloroethane (pp ’DDD) are also detected in the atmosphere of Colmar. A small increase in the pesticide concentrations in the atmosphere (gas and particles) was observed during treatments.     

Trapping efficiency of selected adsorbents for various airborne pesticides.

A study was conducted to compare the efficiency of five adsorbents used by government and private laboratories to collect airborne pesticides. Six pesticides, acephate, chlordane, chlorpyrifos, diazinon, heptachlor, and propoxur, were vaporized in a closed system and collected on each of the adsorbents, Chromosorb 102, ORBO 42, ORBO 44 (chlordane and heptachlor only), polyurethane foam (PUF) or Tenax GC, by drawing 250 L of air through the adsorbent. There were no differences in collection efficiency of the five pesticides on Chromosorb 102, ORBO's 42/44, and PUF. The efficiency with Tenax was somewhat less with several of the pesticides.     

Validation and application of an analytical method for determining pesticides in the gas phase of ambient air

A method for determining atmospheric concentrations of eight pesticides applied to corn and soybean crops in Mato Grosso state, Brazil is presented. The method involved a XAD-2 resin cartridge coupled to a low volume air pump at 2 L min?1 over 8 hours. Pesticides were recovered from the resin using sonication with n-hexane:ethyl acetate and determined by GC-MS. Good accuracy (76-128%) and precision (CV < 20%) were obtained for atrazine, chlorpyrifos, alpha- and beta-endosulfan, endosulfan sulfate, flutriafol, malathion, metolachlor and permethrin. Method detection ranged from 9.0 to 17.9 ng m?3. This method was applied to 61 gas phase samples collected between December 2008 and June 2009. Atrazine and endosulfan were detected both in urban and rural areas indicating the importance of atmospheric dispersion of pesticides in tropical areas. The simple and efficient extraction method and sampling system employed was considered suitable for identifying pesticides in areas of intense agricultural production.     

Simultaneous analysis of 50 pesticides in water samples by solid phase extraction and GC-MS

A multiresidue analysis of 50 pesticides has been developed as a rapid screening method for organic contaminants in water samples. Solid phase extraction was accomplished with two adsorbents in a single column. Simultaneous analysis was performed with gas chromatography-mass spectrometry (GC-MS). The limits of detection for each pesticide are at sub-ppb levels. This method was used to check contamination of water from the Adige river (Northern Italy).     

Validation and application of an analytical method for determining pesticides in the gas phase of ambient air

A method for determining atmospheric concentrations of eight pesticides applied to corn and soybean crops in Mato Grosso state, Brazil is presented. The method involved a XAD-2 resin cartridge coupled to a low volume air pump at 2 L min^?1 over 8 hours. Pesticides were recovered from the resin using sonication with n-hexane:ethyl acetate and determined by GC-MS. Good accuracy (76–128%) and precision (CV < 20%) were obtained for atrazine, chlorpyrifos, alpha- and beta-endosulfan, endosulfan sulfate, flutriafol, malathion, metolachlor and permethrin. Method detection ranged from 9.0 to 17.9 ng m^?3. This method was applied to 61 gas phase samples collected between December 2008 and June 2009. Atrazine and endosulfan were detected both in urban and rural areas indicating the importance of atmospheric dispersion of pesticides in tropical areas. The simple and efficient extraction method and sampling system employed was considered suitable for identifying pesticides in areas of intense agricultural production.     

Pesticides in the surface waters of the Camanducaia River watershed,Brazil

Abstract

Camanducaia River is part of the Piracicaba watershed responsible for pumping water into the Cantareira System, which is one of the main water sources for the metropolis of São Paulo and Campinas, Brazil. Intensive use of pesticides and hilly topography represents a situation of high risk for river water contamination. Therefore, water samples from 12 locations were collected along the Camanducaia River and its tributaries, over a period of 4?mo during the rainy season, and analyzed by GC-MS/MS or UPLC- MS/MS for the presence of 46 pesticides. Seven pesticides (fipronil, methyl parathion, metolachlor, atrazine, carbofuran, diuron, and simazine) were positively detected. Only atrazine (the most frequently detected) and diuron were present at concentrations above the limit of quantification of the analytical method (0.32 and 0.57?μg L^?1 for atrazine and diuron, respectively). Pesticides detection frequency was higher than expected for a river system where only 11.8% of the land area is under agriculture. The vulnerability of the Camanducaia basin to pesticide contamination is attributed to the high annual precipitation (> 1.5?m y^?1 in the headwaters), associated with topographical features (steep terrain) and soil types that favor surface runoff, which has been exacerbated by poor soil management practices.     

LC-MS/MS determination of pesticide residues in fruits and vegetables

The aim of the research is to evaluate pesticide residue contamination of fresh and frozen fruits and vegetables, agricultural raw material, purchased from Polish farmers for production of frozen fruits and vegetables, and the estimation of the multiresidue method effectiveness expressed as the proportion of pesticides detected in food samples to the total number of pesticides analyzed by multiresidue methods. A total of 144 samples (of black currants, red currants, raspberries, cherries, strawberries, blackberries, cauliflowers and broccoli) were analyzed using LC-MS/MS method for the determination of 60 pesticides. QuEChERS extraction, matrix-matched calibration and dynamic multiple reaction monitoring method were used. Residues of 15 compounds, mainly fungicides and insecticides, were detected in 46 samples. The percentage of samples with residues above the maximum residue levels (MRL) was 15%, whereas samples with residues below MRL were 17%. A total of 13 samples contained more than one pesticide residue. Pesticide residues were detected most often in samples of black currants (50%), broccoli (36.4%), raspberries (29%) and red currants (21.8%). The most frequently detected pesticides were carbendazim and acetamiprid. The proportion of pesticides detected during our study to the total number of analyzed pesticides amounted to 25%. It was compared to literature findings. For three fourth of multiresidue methods, the proportion was below 50% for methods developed for the analysis of less than 100 pesticides, and below 30% for methods developed for the analysis of more than 100 pesticides. It appears that a lot of efforts and means is lost on pesticides never or rarely detected in examined samples. The workload and cost effectiveness of the development and application of multiresidue methods along with the range of pesticides covered by the method should be carefully and thoroughly considered anytime when a new method or workflow is developed. Including non-targeted screenings in pesticide residue control seems to be an alternative worth considering.     

Utilization of long duration high-volume sampling coupled to SPME-GC-MS/MS for the assessment of airborne pesticides variability in an urban area (Strasbourg,France) during agricultural application

Atmospheric samples have been collected between 14 March and 12 September 2012 on a 2-week basis (15 days of sampling and exchange of traps each 7 days) in Strasbourg (east of France) for the analysis of 43 pesticides. Samples (particle and gas phases) were separately extracted using Accelerated Solvent Extraction (ASE) and pre-concentrated by Solid Phase Micro-Extraction (SPME) before analysis by gas chromatography coupled to tandem mass spectrometry (GC-MS/MS). Four SPME consecutive injections at distinct temperatures were made in order to increase the sensitivity of detection for the all monitored pesticides. Currently used detected pesticides can be grouped in four classes; those used in maize crops (acetochlor, benoxacor, dicamba, s-metolachlor, pendimethalin, and bromoxynil), in cereal crops (benoxacor, chlorothalonil, fenpropimorph, and propiconazole), in vineyards (tebuconazole), and as herbicides for orchards, meadows of green spaces (2,4-MCPA, trichlopyr). This is in accordance with the diversity of crops found in the Alsace region and trends observed are in accordance with the period of application of these pesticides. Variations observed permit also to demonstrate that the long time sampling duration used in this study is efficient to visualize temporal variations of airborne pesticides concentrations. Then, long time high-volume sampling could be a simple method permitting atmospheric survey of atmospheric contamination without any long analysis time and consequently low cost.     

Multiresidue screening methods for the determination of pesticides in tomatoes

The possibility of applying thin layer chromatography (TLC) detection for the analysis of pesticide residues in tomatoes was investigated. Samples of tomatoes that have never been treated with pesticide were fortified with atrazine, carbaryl, carbofuran, chloroxuron, diuron, dimethoate, imazalil, oxamyl and methamidophos. The samples were extracted, cleaned-up by gel permeation chromatography and then applied on silica gel plates. The pesticides were eluted with ethyl acetate and dichloromethane. Two eluting solvent systems were tested, one using the reagents o-toluidine + potassium iodite (o-TKI) and the other p- nitrobenzene fluoroborate (NBFB). After the development of the plates, the diameter of the spots was measured. The lowest minimum detection quantity (MDQ) for o-TKI system for atrazine was 12 ng. The highest was 125 ng for carbofuran. Using NBFB system, the lowest MDQ was 60 ng for carbaryl and the highest was 70 ng obtained for carbofuran. Considering the concentration of these pesticides in the spiked tomato samples, the minimum concentration was 1.1 ng/microL and 32.3 ng/microL for atrazine and carbofuran, respectively, by using o-TKI system. For NBFB system the minimum concentration reached was 3.5 ng/microL and 4.3 ng/microL for carbaryl and carbofuran, respectively. This study showed that TLC can be used for semi-quantitative analysis.     

Isolation and characterization of a Pseudomonas aeruginosa from a virgin Brazilian Amazon region with potential to degrade atrazine

The use of pesticides to increase agricultural production can result in the contamination of the environment, causing changes in the genetic structure of organisms and in the loss of biodiversity. This practice is also inducing changes in the rainforest ecosystem. In this work, a Pseudomonas aeruginosa isolated from a preservation soil area of the Brazilian Amazon Forest, without usage of any pesticide, was evaluated for its potential to degrade atrazine. This isolate presented all responsible genes (atzA, atzB, atzC, atzD, atzE, and atzF) for atrazine mineralization and demonstrated capacity to use atrazine as a nitrogen source, having achieved a reduction of 44 % of the initial concentration of atrazine after 24 h. These results confirm gene dispersion and/or a possible contamination of the area with the herbicide, which reinforces global concern of the increase and intensive use of pesticides worldwide.     

Leaching of atrazine, metolachlor and diuron in the field in relation to their injection depth into a silt loam soil

A field experiment was conducted on a Calcaric Cambisol soil to study the consequences of the penetration depth and properties of pesticides on the risk of subsequent leaching. Three pesticides with different mobility characteristics and bromide were injected at 30 cm (where soil organic matter (OM) was 2%) and 80 cm (soil OM 0.5%) on irrigated plots without a crop. The migration of injected solutes was assessed for two years by sampling the soil solution using six porous cups installed at 50 and 150 cm depth and by relating solute contents to drainage water flux estimated by the STICS model (Simulateur mulTIdisciplinaire pour les Cultures Standard). Pesticides injected at 30 cm were strongly retained so that no metolachlor or diuron was detected at 50 and 150 cm. The ratio of atrazine peak concentration in the soil solution to concentration in the injected solution (C/C₀) was 1 × 10⁻³ and 0.2 × 10⁻³, respectively, at 50 and 150 cm. When injected at 80 cm, (C/C₀) of atrazine, metolachlor and diuron were 10 × 10⁻³, 1 × 10⁻³ and 0.3 × 10⁻³ at 150 cm, respectively; 1/(C/C₀) was correlated with K_oc values reported from databases. The ratio of drainage volume to the amount of water at field capacity in the soil layer between the injection point at 30 cm and the water sampling level (V/V₀) at 50 and 150 cm was 0.6 and 0.9, respectively, for bromide and 1.6 and 1.0 for atrazine. V/V₀ of the injected solutes at 80 cm was for bromide, atrazine, metolachlor and diuron 0.6, 0.9, 1.2 and 1.7, respectively; pesticide V/V₀ was correlated with K_oc. The retardation factor was a good indicator of migration risk, but tended to overestimate retardation of molecules with high K_oc. Atrazine desorption represented an additional leaching risk as a source of prolonged low contamination. The large variability in soil solution of bromide and pesticide concentrations in the horizontal plane was attributed to flow paths and clods in the tilled soil layer. This heterogeneity was assumed to channel water fluxes into restricted areas and thereby increase the risk of groundwater contamination. The methodology used in the field proves to provide consistent results.     

Variability of atmospheric pesticide concentrations between urban and rural areas during intensive pesticide application

Intensive pesticide use leads to the contamination of water, soil and atmosphere. Atmospheric transport is responsible for pesticide dispersal over long distances. In this study, we evaluate the local dispersal of pesticides from agricultural to urban areas. For this purpose, three high-volume samplers, each equipped with a glass fiber filter and XAD-2 resin for the sampling of particulate and gas phase have been placed in a south-west transect (predominant wind direction) characteristic of rural and urban areas. The urban site (Strasbourg centre) is situated in the middle of two rural sites. Samples were taken simultaneously at three sites during pesticide treatments in autumn and spring 2002–2003. Sampling took place for 24 h at a flow rate of 10–15 m³ h⁻¹. The pesticides studied were those commonly used in the Alsace region for all crops (maize, cereal, vines …). Many of the pesticides analysed in atmospheric samples were not detected or observed very episodically at very low concentrations. For metolachlor, alachlor, trifluralin, atrazine and diflufenican, higher concentrations were observed, essentially during the application of these compounds. Moreover, some “spraying peaks” were observed for alachlor in the south rural site (near crops) at a level of 31 ng m⁻³ on 16–17 May 2003. These results show site and time dependence of atmospheric contamination by pesticides. A limited dispersal was also observed especially in the urban area during the application periods of pesticides.     

Field evaluation of two diffusive samplers and two adsorbent media to determine 1,3-butadiene and benzene levels in air

Two types of diffusive samplers, both of which are compatible with thermal desorption, but differ in their geometry—SKC-Ultra (badge-type) and Radiello (radial symmetry-type)—were evaluated indoors and outdoors under varying temperature, humidity and wind speed conditions, using the graphitized adsorbents Carbopack X or Carbograph 5 to measure 1,3-butadiene and benzene in ambient air. The results obtained by diffusive sampling were compared with results obtained using a conventional active sampling method over both long (1 week) and shorter periods (6–24 h). Analysis and detection were performed using an automatic thermal desorber (ATD) connected to a gas chromatograph-flame ionization detector (GC/FID). Results from each sampler and adsorbent combination were examined using ordinary or multiple linear regression analysis. The overall uncertainty (OU) was also determined. In general, the results obtained with both samplers showed good agreement with those obtained by active sampling. Carbopack X appeared to be a more efficient adsorbent than Carbograph 5 for 1,3-butadiene, but the two adsorbents were equivalent for benzene. No effects of either humidity or air velocity were observed. Minor temperature effects were observed for both samplers for 1,3-butadiene. In summary, the results confirmed the accuracy of sampling rates previously determined for the two samplers and adsorbents. We consider the two samplers to be suitable for stationary and personal monitoring for the general population of 1,3-butadiene and benzene in various environments, indoors and outdoors. They are almost independent of meteorological conditions and may be suitable for monitoring industrial atmospheres.     

Cantilever nanobiosensor using tyrosinase to detect atrazine in liquid medium

The aim of this study was to develop a cantilever nanobiosensor for atrazine detection in liquid medium by immobilising the biological recognition element (tyrosinase vegetal extract) on its surface with self-assembled monolayers using gold, 16-mercaptohexadecanoic acid, 1-ethyl-3-[3-dimethylaminopropyl] carbodiimide hydrochloride/n-hydroxysuccinimide. Cantilever nanobiosensors presented a surface compression tension increase when atrazine concentrations were increased, with a limit of detection and limit of quantification of 7.754 ppb (parts per billion) and 22.792 ppb, respectively. From the voltage results obtained, the evaluation of atrazine contamination in river and drinking water were very close to those of the reference sample and ultrapure water, demonstrating the ability of the cantilever nanobiosensor to distinguish different water samples and different concentrations of atrazine. Cantilever nanosensor surface functionalization was characterised by combining polarisation modulation infrared reflection-absorption spectroscopy and atomic force microscopy and indicating film thickness in nanometric scale (80.2 ± 0.4 nm). Thus, the cantilever nanobiosensor developed for this study using low cost tyrosinase vegetal extract was adequate for atrazine detection, a potential tool in the environmental field.     

Influence of humic substances on the photolysis of aqueous pesticide residues

The present work investigated the direct and indirect photolysis of pesticide residues (atrazine, imazaquin, iprodione), in aqueous solutions and under UV-visible radiation (280-480nm). Different kinds of humic substances (HS) were added to samples in order to evaluate their behaviour as possible photocatalysts and their effect on the photolysis of pesticides. The fulvic acids were purchased from the International Humic Substances Society, and they were added to samples in concentrations ranging from 1 to 150 mgl(-1). Titanium dioxide was used as the photocatalyst, in concentration ranging from 10 to 150 mgl(-1). Pesticides photolysis were measured by UV-visible absorption spectroscopy and differential pulse polarography with all used pesticides, reaching total degradation after 2h of irradiation, thus indicating a fast direct photolysis. Photocatalysis by TiO(2) could increase the pesticides photolysis rate up to 40%. This effect, however, was not observed for imazaquin photolysis. Again, except for imazaquin, HS presence showed a positive effect in increasing pesticide degradation, but only within specific concentration ranges (below 10mg l(-1) for iprodione and about 30mgl(-1) for atrazine). Above these ranges HS induce a decrease in the pesticides photolysis rate. Spin-trapping measurements by electronic paramagnetic resonance spectroscopy, using the spin-trap DMPO, showed that HS are able to photogenerate hydroxyl radicals, increasing the pesticides molecule degradation. However, the HS also react with the photogenerated hydroxyl radical, influencing the pesticide photolysis, leading to a decrease in the photolysis rate and causing it to be strongly dependent on the nature and concentration of residues in the water to be treated.     

Molecularly imprinted polymer for analysis of trace atrazine herbicide in water

A molecularly imprinted polymer (MIP) for atrazine was synthesized by non-covalent method. The binding capacity of MIP was 1.00 mg g^{? 1} polymer. The selectivity and recovery were investigated with various pesticides which are mostly, found in the environment, for both similar and different chemical structure of atrazine. The competitive recognition between atrazine and structurally similar compounds was evaluated and it was found that the system provided highest recovery and selectivity for atrazine while low recovery and selectivity were obtained for the other compounds. The highest recovery was obtained from MIP compared with non-imprinted polymer (NIP), a commercial C₁₈ and a granular activated carbon (GAC) sorbent. The method provided high recoveries ranged from 94 to 99% at two spiked levels with relative standard deviations less than 2%. The lower detection limit of the method was 80 ng L^{? 1}. This method was successfully applied for analysis of environmental water samples.     

Leaching and degradation of corn and soybean pesticides in an Oxisol of the Brazilian Cerrados

Pesticide pollution of ground and surface water is of growing concern in tropical countries. The objective of this pilot study was to evaluate the leaching potential of eight pesticides in a Brazilian Oxisol. In a field experiment near Cuiabá, Mato Grosso, atrazine, chlorpyrifos, lambda-cyhalothrin, endosulfane alpha, metolachlor, monocrotofos, simazine, and trifluraline were applied onto a Typic Haplustox. Dissipation in the topsoil, mobility within the soil profile and leaching of pesticides were studied for a period of 28 days after application. The dissipation half-life of pesticides in the topsoil ranged from 0.9 to 14 d for trifluraline and metolachlor, respectively. Dissipation curves were described by exponential functions for polar pesticides (atrazine, metolachlor, monocrotofos, simazine) and bi-exponential ones for apolar substances (chlorpyrifos, lambda-cyhalothrin, endosulfane alpha, trifluraline). Atrazine, simazine and metolachlor were moderately leached beyond 15 cm soil depth, whereas all other compounds remained within the top 15 cm of the soil. In lysimeter percolates (at 35 cm soil depth), 0.8-2.0% of the applied amounts of atrazine, simazine, and metolachlor were measured within 28 days after application. Of the other compounds less than 0.03% of the applied amounts was detected in the soil water percolates. The relative contamination potentials of pesticides, according to the lysimeter study, were ranked as follows: metolachlor > atrazine = simazine > monocrotofos > endsulfane alpha > chlorpyrifos > trifluraline > lambda-cyhalothrin. This order of the pesticides was also achieved by ranking them according to their effective sorption coefficient Ke, which is the ratio of Koc to field-dissipation half-life.     

Gas chromatography/mass spectrometry applied for the analysis of triazine herbicides in environmental waters

The excess use of triazine herbicides in agriculture causes severe contamination to the environment especially for ground water. Gas chromatography coupled with mass spectrometry (GC/MS) was used to analyze simazine, atrazine (ATR), cyanazine, as well as the degradation products of ATR such as deethylatrazine and deisopropylatrazine in environmental water samples. These compounds were baseline separated by the established GC method. The water samples were pre-concentrated by solid-phase-extraction (SPE) and analyzed by ion trap MS at sub- to low-ppt levels. Recovery of ATR by the SPE pre-concentration using a C18 cartridge was determined as 90.5 +/- 3.5%. Detection limit of the method using selected ion monitoring technique for ATR was 1.7 ppt when one liter water was analyzed. The relative analytical error for ATR fortified water samples at 200 ppt was -12.5% (n=12) with triple analysis and the relative standard deviation was 3.2%. Trace levels of ATR at 3.9 and 9.7 ppt were determined in water samples collected from a reservoir and a river in Hong Kong.