太原市气悬颗粒物上多环芳烃的测量与分布研究

2 0 0 1年 3月下旬 ,在太原市建成区均匀布设 1 5个网格点 ,利用新型便携式仪器 ,连续 5天监测了各点大气颗粒物上多环芳烃 (PPAHs)的浓度。结果表明 ,PPAHs浓度范围为 3 6ng/m3～ 3 1 3 ng/m3;全市上下午平均浓度为 1 3 9ng/m3;上午浓度平均值是下午的 2倍 ;全市空间分布整体上由北向南逐渐降低 ,东北部最重 ,东南部最轻 ;不同功能区的污染程度依次为 :一电厂化工区 >太钢工业区 >桃园商业区 >太行居民区。本文还着重探讨了污染分布的成因 ,并提出了改善大气质量的建议。     

Estimation of the contributions of long range transported aerosol in East Asia to carbonaceous aerosol and PM concentrations in Seoul, Korea using highly time resolved measurements: a PSCF model approach

The contributions of long range transported aerosol in East Asia to carbonaceous aerosol and particulate matter (PM) concentrations in Seoul, Korea were estimated with potential source contribution function (PSCF) calculations. Carbonaceous aerosol (organic carbon (OC) and elemental carbon (EC)), PM(2.5), and PM(10) concentrations were measured from April 2007 to March 2008 in Seoul, Korea. The PSCF and concentration weighted trajectory (CWT) receptor models were used to identify the spatial source distributions of OC, EC, PM(2.5), and coarse particles. Heavily industrialized areas in Northeast China such as Harbin and Changchun and East China including the Pearl River Delta region, the Yangtze River Delta region, and the Beijing-Tianjin region were identified as high OC, EC and PM(2.5) source areas. The conditional PSCF analysis was introduced so as to distinguish the influence of aerosol transported from heavily polluted source areas on a receptor site from that transported from relatively clean areas. The source contributions estimated using the conditional PSCF analysis account for not only the aerosol concentrations of long range transported aerosols but also the number of transport days effective on the measurement site. Based on the proposed algorithm, the condition of airmass pathways was classified into two types: one condition where airmass passed over the source region (PS) and another condition where airmass did not pass over the source region (NPS). For most of the seasons during the measurement period, 249.5-366.2% higher OC, EC, PM(2.5), and coarse particle concentrations were observed at the measurement site under PS conditions than under NPS conditions. Seasonal variations in the concentrations of OC, EC, PM(2.5), and coarse particles under PS, NPS, and background aerosol conditions were quantified. The contributions of long range transported aerosols on the OC, EC, PM(2.5), and coarse particle concentrations during several Asian dust events were also estimated. We also investigated the performance of the PSCF results obtained from combining highly time resolved measurement data and backward trajectory calculations via comparison with those from data in low resolutions. Reduced tailing effects and the larger coverage over the area of interest were observed in the PSCF results obtained from using the highly time resolved data and trajectories.     

Modeling of oak pollen dispersal on the landscape level with a mesoscale atmospheric model

We present the extension and application of the mesoscale atmospheric meteorology model METRAS for dispersion of oak pollen. We incorporated functions for pollen emission, pollen viability and pollen deposition into METRAS and simulated pollen dispersal on a scale of up to 200 km. The basis of the simulations is a real landscape structure that includes topography, land use, and the location and size of oak stands. We simulated the oak pollen dispersion of one single oak stand with an estimated annual pollen production of 1 billion pollen grains/m² forest surface on two exemplary days of the flowering season in 2000. Depending on the meteorological situation of the simulated days, a pollen cloud with about 10 pollen/m³ may extend up to 30 km from the source. Downstream of the oak stand, approximately 1,000 pollen/m² deposited up to a distance of 25 km, and lower amounts of pollen deposited up to 100 km away. These values of pollen concentration and deposition lay within the range of published field studies. Overall, it is shown that mesoscale atmospheric models are applicable to simulate pollen dispersal on the landscape level.     

Effects of along-shore wind stress and surface cooling on the formation of shelf sea fronts in a simple air-sea interaction model

This paper presents numerical simulation results from a set of control and sensitivity experiments on the effects of winter-time air-sea interaction on the variability of sea surface temperature (SST) on a two-dimensional continental shelf which is uniform in the along-shore direction and is bounded to the west by a straight coast and to the east by a prescribed Gulf Stream front. In the control experiment, the model ocean circulation is driven by a time-dependent wind forcing which is parameterically coupled to the cross-shelf SST gradient. In the sensitivity experiments, wind stress, diabatic cooling and air-sea coupling are turned on separately to estimate the individual contribution of each effect to the cross-shelf SST variation. Experiments have also been carried out for different coupling strengths and diabatic cooling rates to examine the model sensitivity to these paramenters. The model results indicate that air-sea interaction could induce a secondary SST front on the shelf. Comparisons of model results with observations obtained during the Genesis of Atlantic Lows Experiment conducted off the east coasts of the Carolinas during January and February 1986 qualitatively confirm our finding.     

Optimisation of reduction of global CO2 emission based on a simple model of the carbon cycle

A simple model has been designed to describe the interaction of climate and biosphere. Carbon dioxide, understood as a major emitted gas, leads to a change of global climate. Economic interpretation of the model is based on the maximisation of the global CO₂ cumulative emissions. The two most important profiles of emission have been obtained: optimal and multi-exponential suboptimal profiles, each displaying different characteristics. This revised version was published online in July 2006 with corrections to the Cover Date.     

Actinides and decay products in selected produce and bioindicators in the vicinity of a uranium plant

Cypress needles collected at the edge of the Malvési uranium facility (SW France) exhibit enhanced activities of actinides and some decay products (uranium, americium, plutonium, (230)Th, (226)Ra) compared to a remote site. These enhanced activities resulted from the release of U via smokestacks and passive release from former artificial ponds located inside the nuclear site. Enhanced activities are also observed in selected produce (wheat, lettuce, fruits) sampled from the edge of the site. However, excess actinides measured in wheat grains in 2007 are inconsistent with the activities and the uranium ratio measured in the soils. This result suggests that the studied annual crops were contaminated mainly through the short-term release of airborne actinides, and that other transfer pathways, such as, uptake through the roots or adhesion of soil particles, were negligible.     

Impact of long-term exposure to mosquito coils: residual deposition and dissipation of D-trans-allethrin in a room

A D-trans-allethrin-based mosquito repellent coil formulation was used continuously in a room for 30 d. Two different experiments were conducted and the deposition of residues on different surfaces of the room was determined. Studies were conducted continuously for a period of 30 d in a fully closed room and in another room kept open for 14 h per day. The residues deposited on different surfaces, ceiling, side walls and floor, were measured. The results showed the accumulation of high concentrations of allethrin on all the surfaces of the room when the room was in a fully closed condition. Samples collected from the ceiling showed residues of D-trans-allethrin of 6.34-148.63 microg m(-2) during the 30 d study, the side walls 4.68-170.72 microg m(-2) and the floor 20.00-184.52 microg m(-2) Maximum residues were observed in 30 d samples collected from the ceiling and floor. The residual concentrations were nearly 10 times higher in samples collected from the closed room. Discontinuation of the use of the mosquito repellent after 30 d led to a gradual decrease in the concentrations of residues on all the surfaces. The influence of environmental parameters on the dissipation of residues was also studied.     

Uranium speciation in moorland river water samples: a comparison of experimental results and computer model predictions

An on-line method has been developed for separating inorganic and organic bound uranium species present in river water samples. The method utilised a small chelating resin (Hyphan) column incorporated into the sample introduction manifold of an ICP-MS instrument. The method was evaluated for samples from rivers on Dartmoor (Devon, UK), an area of granite overlain with peat bogs. The results indicate that organic-uranium species form a major proportion (80%) of the total dissolved uranium present. Further work with synthetic water samples indicated that the level of dissolved organic carbon played a greater role in determining the level of organic-uranium species than did sample pH. Computer models for the water samples were constructed using the WHAM program (incorporating uranium data from the Nuclear Energy Agency Thermochemical Database project) in order to predict the levels of organic-uranium species that would form. By varying the proportion of humic and fulvic acids used in the humic component, predictions within 10% of the experimental results were obtained. The program did exhibit a low bias at higher pH values (7.5) and low organic carbon concentrations (0.5 microg ml(-1)), but under the natural conditions prevalent in the Dartmoor water samples, the model predictions were successful.     

Measurements and Modelling of Air Pollution in a Street Canyon in Helsinki

A measuring campaign was conducted in the street canyon 'Runeberg street' in Helsinki in 1997. Hourly concentrations of carbon monoxide (CO), nitrogen oxides (NO_X), nitrogen dioxide (NO₂) and ozone (O₃) were measured at the street and roof levels, and the relevant hourly meteorological parameters were measured at the roof level. The hourly street level measurements and on-site electronic traffic counts were conducted during the whole year 1997, and roof level measurements were conducted during approximately two months, from 3 March to 30 April in 1997. The Operational Street Pollution Model (OSPM) was used to calculate the street concentrations and the results were compared with the measurements. The overall agreement between measured and predicted concentrations was good for CO and NO_x, but the model slightly overestimated the measured concentrations of NO₂. The database, which contains all measured and predicted data, is available for a further testing of other street canyon dispersion models.     

Attribution of aerosol light absorption to black carbon and volatile aerosols

We investigated the contribution of volatile aerosols in light-absorption measurement by three filter-based optical instruments [aethalometer, continuous light-absorption photometer (CLAP), and continuous soot monitoring system (COSMOS)] at Gosan Climate Observatory (GCO) from February to June 2012. The aerosol absorption coefficient (σ _abs) and the equivalent black carbon (BC) mass concentration (M _BC) measured by the aethalometer and CLAP showed good agreement with a difference of 9 %, which is likely due to the instrumental uncertainty. However, σ _abs and M _BC measured by the COSMOS with a heated inlet were found to be approximately 44 and 49 % lower than those measured by the aethalometer and CLAP under ambient conditions, respectively. This difference can be attributed to the light absorption by the volatile aerosols coexisting with the BC. Even considering inherent observational uncertainty, it suggests that approximately 35–40 % difference in the σ _abs and M _BC can be contributed by volatile aerosols. Increase in the difference of M _BC measured by the aethalometer and COSMOS with the increasing thermal organic carbon (OC) measured by Sunset OC/EC analyzer further suggests that the filter-based optical instruments without the use of a heater are likely to enhance the value of σ _abs and M _BC, because this sample air may contain both BC and volatile aerosols.     

Application of flow cytometry and cell sorting to the bacterial analysis of environmental aerosol samples

Flow cytometry (FCM) combined with viability staining is a useful tool in discerning viable bacteria in environmental samples where traditional culture methods may fail. Contamination of aerosol samples with dust and other non-biological particles can interfere with accurate sample analysis and therefore there is a desire to exclude those particles from analysis. Particles were sorted according to their light scattering properties, cultured and isolates obtained. Isolates were cultured in suspension and reanalyzed by flow cytometry. The isolates were also analyzed and identified by DNA sequence analysis. Isolates with statistically similar light scattering properties shared common sequence identification. Isolates exhibited distinct light scattering profiles that roughly correlated with their originating gate, but often the peak of the profile was outside that gate.     

Monitoring long-term variation of aerosol composition: a dual particle-size approach applied to Hong Kong

The 1990's time series in Hong Kong for various components oftotal suspended particulate matter (TSP) and PM₁₀ have beenanalyzed in order to assess two distinct types of anthropogenicinput. The first of these relates to the immense reclamation andconstruction activities for new developments and airportconstruction. The concentrations of crustal components inPM₁₀ (= TSP – PM₁₀) were found to peak at the time ofthis maximum activity. A second type of anthropogenic input,ambient lead from petrol vehicles, has decreased in Hong Kongand now represents a regional background. Ambient bromine nowarises mainly from the seasalt source.     

Urban and suburban aerosol in Yokohama, Japan: a comprehensive chemical characterization

This article analyses elemental composition of suspended particulate matter (SPM) samples collected monthly from 1999 to 2005 at two locations in Yokohama, Japan. Microwave digestion and inductively coupled plasma mass spectroscopy was employed to measure Mg, Al, Ca, V, Cr, Mn, Ni, Cu, Zn, Ga, As, Se, Rb, Sr, Ag, Cd, Cs, Ba, Pb, and Bi. Water-soluble ions (Na^?+?, NH₄ ^?+?, K^?+?, Ca^2?+?, Cl^???, NO₃ ^???, and SO₄ ^2???) and carbonaceous mass (elemental and organic carbon) were detected using ion chromatograph and CHN analyzer, respectively. The results indicate that the composition of SPM on one of the sites is determined by automobile emissions and on the other by industrial combustions. The impact of the emission regulations for automobiles in large Japanese cities, which were enacted during 2002 and 2003, on the SPM composition of the samples is also studied.     

兰州市气溶胶中金属与非金属元素的污染规律

通过对兰州市空气飘尘中粗、细颗粒物上化学元素的分布规律与特征的分析 ,指出了细颗粒物 (PM2 .5 )是一些有毒有害元素的主要携带者。这是可以在肺泡沉积 ,并能直接进入血液循环 ,对人体产生危害的重要部分     

A review of workplace aerosol sampling procedures and their relevance to the assessment of beryllium exposures

Standardized conventions governing the fractions of airborne particles that can penetrate the human head airways, the thoracic airways and the alveolar spaces have been internationally (although not universally) adopted. Several agencies involved in setting limit values for occupational exposure concentrations have taken these conventions into account when considering the appropriate standard for specific chemicals, in order to ensure the standards are biologically relevant. A convention is selected based on the characteristic health effects, and forms the basis of measurement against the limiting concentration value. In order to assess exposure for comparison to this metric or any other purposes, it is necessary to choose a sampler whose performance matches the convention, and protocols have been developed and used to test sampler performance. Several aerosol sampling devices are available, nominally at least, for each of the conventions. Some considerations important to the sampling of airborne particles containing beryllium with regard to the sampling conventions, the test protocols and sampler performance are discussed.     

Investigation of the aerosol structure over an urban area using a polarization lidar

The paper presents a lidar study of the aerosol structure in the planetary boundary layer in the case of radiation fog and haze. A conceptual model of the dynamics of the depolarization coefficient profile during the mixing layer development, taking into account the presence of a multilayered inversions and radiation fogs, is proposed. Various techniques are employed in the processing of the lidar signal in order to determine the mixing layer height as well as more details of the aerosol structure in the low atmosphere, namely, finding the maximum of the signal returned from the lowest temperature inversion, the crossing point of the S function's first derivative with the x axis, and profiles of the depolarization ratio. After the complete destruction of the stable stratification, a low constant value of the depolarization ratio within the newly formed mixing layer is being observed. The study of stable boundary layer disintegration and convective boundary layer formation in the presence of fogs and/or clouds is of both scientific and practical significance in what concerns the protection of the environment and the aviation meteorology.     

Computational Fluid Dynamics Modelling of the Pollution Dispersion and Comparison with Measurements in a Street Canyon in Helsinki

A measuring campaign was conducted in a street canyon (Runeberg St.) in Helsinki in 2003–2004. The concentrations of NO _x , NO₂, PM₁₀ and PM_2.5 were measured at street level and at roof level at an urban background location. This study utilises the data measured from 1 Jan to 30 April, 2004, when wind speed and direction measurements were also conducted on-site at the roof level. The computational fluid dynamics model ADREA-HF was used to compute the street concentrations, and the results were compared with the measurements. The predictions for the selected cases agreed fairly well (within < 25 % for 15 min average values) with the measured data, except for two cases: a windward flow in case of a low wind speed, and a moderate southerly flow parallel to the street canyon. The main reasons for the differences of predictions and measurements are the negligence of traffic-induced turbulence in the modelling and an under-prediction of ventilation of urban background air from a crossing street. Numerical results are presented for various example cases; these illustrate the formation of the vortices in the canyon in terms of the wind direction and speed and the influence of the characteristics of the flow fields on the concentration distributions.     

Air pollutants and the characterization of the organic content of aerosol particles in a mixed industrial/semi-rural area in central Italy

Both regulated and unregulated air pollutants were detected during an intensive seasonal sampling campaign in a mixed industrial/semi-rural area on the outskirts of Rome, Italy, at two sites located opposite a hospital waste incinerator, downwind according to the direction of the prevailing local winds. Concentrations of pollutants were significantly lower than in urban atmospheres. The composition of particulate organic material indicated a heavy biogenic impact, accompanied by a lower contribution from petroleum-related processes. Both PAH and nitro-PAH group compositions of particulates were used to assess the nature and relative importance of sources. Both sites showed that different and diffuse sources contributed to local pollution with a significant contribution from traffic, proving that the hospital waste incinerator was not the main pollution source in this area. Among unregulated compounds, a series of positional isomers of nitro-PAHs and other organic compounds associated with particulate matter were investigated. In particular, 1- and 3-nitrophenanthrene identification was carried out, and they proved to be the most abundant nitro-PAHs.     

Landscape resistance to dispersal: simulating long-term effects of human disturbance on a small and isolated wolf population in southwestern Manitoba, Canada

Landscape fragmentation affects wildlife population viability, in part, through the effects it has on individual dispersal. In addition, some forms of human disturbance impinge on dispersal without physically fragmenting habitats. Here, we use the term "landscape resistance" to capture constraints to dispersal that cannot be linked directly to fragmentation. The extent to which landscape resistance can influence population persistence is not well understood. Agricultural development over the past 60?years has resulted in considerable habitat fragmentation in the Riding Mountain National Park (RMNP) region in southwestern Manitoba, Canada. We examined how park boundaries, roads outside park boundaries and negative human attitudes have altered dispersal success and population persistence. We examined whether stochastic disturbance, representing infectious disease epidemics, further reduced long-term population persistence for various scenarios. Finally, we assessed whether the simultaneous occurrence of the three features had additive effects. We simulated dispersal using HexSim, a spatially explicit individual-based population model, parameterised with data on wolves (Canis lupus) in the RMNP region. Simulations that separately accounted for negative human attitudes and roads outside the park boundaries exhibited lower mean population size than those that ignored these details. Increasing deflection from park boundaries did not appear to have significant impacts. Our results did not indicate the presence of additive effects, and scenarios incorporating all three features had similar results as that of roads. Stochastic disturbance further reduced mean population size. Our results do illustrate how less-visible human disturbances (i.e. those that do not clearly alter landscape characteristics) can significantly limit dispersal and population persistence.     

Chemical composition of individual aerosol particles from working areas in a nickel refinery

Individual aerosol particles (n = 1170) collected at work stations in a nickel refinery were analyzed by wavelength-dispersive electron-probe microanalysis. By placing arbitrary restrictions on the contents of sulfur and silicon, the particles could be divided into four main groups. Scanning electron images indicated that most of the particles examined were relatively small (< or = 2 microm, equivalent projected area diameter), and that their morphology suggested formation from a melt. There was an absence of well-defined phases and simple stoichiometries, indicating that exposures to pure substances such as nickel subsulfide or specific oxides appeared not to occur. Although the elemental composition of particles varied greatly, a rough association was evident with the known elemental content of the refinery intermediates. The implications of the findings for aerosol speciation measurements, toxicological studies and interpretation of adverse health effects are explored.