Twenty years of achievements in China’s implementation of the Stockholm Convention

● China’s implementation of the SC was systematically studied. ● Implementation process of the SC can be roughly divided into three stages. ● DDT and HCH concentrations in the air have been steadily decreasing. ● China has safely disposed of 6352.1 tons of pesticide POPs. Persistent organic pollutants (POPs) are extremely harmful to the environment and human health; the Stockholm Convention on Persistent Organic Pollutants was therefore adopted by the international community in 2001 to eliminate or reduce the production, use, and emissions of POPs. China is the largest developing country that has signed the Stockholm Convention, and thus plays an important role in its implementation. This paper systematically studies the practice and achievements of China since it signed the Stockholm Convention 20 years ago. China has established an implementation guarantee system including institutions, implementation mechanisms, policies, law enforcement, and scientific and technological support. During the 20 years since the implementation of the Stockholm Convention, dichlorodiphenyltrichloroethane (DDT) and hexachlorocyclohexane (HCH) concentrations in the air have been steadily decreasing, and Perfluorooctane sulfonic acid/Perfluorooctane sulfonyl fluoride (PFOS/PFOSF) concentrations in water bodies have decreased. In the past 20 years, China has safely disposed of 6352.1 tons of pesticide persistent organic pollutants and 36998 sets of electrical equipment containing polychlorinated biphenyls (PCBs), with a disposal rate of 100%. In the future, China will further strengthen the construction of persistent organic pollutant monitoring networks, scientific research, publicity, education, and international cooperation to improve environmental quality, providing a reference for other countries to implement the Stockholm Convention.     

Untargeted metabolomic analysis of pregnant women exposure to perfluorooctanoic acid at different degrees

● Metabolome can distinguish pregnant women exposure to PFOA at different degrees. ● Metabolome can reveal the metabolic changes of pregnant women exposure to PFOA. ● PFOA exposure degrees could affect the GSH metabolism of pregnant women. ● PFOA exposure degrees could change the microbiota metabolism of pregnant women. Perfluorooctanoic acid (PFOA) is a novel type of persistent synthetic organic pollutant, and its exposure on pregnant women can cause some adverse effects, such as pregnancy-induced hypertension, gestational diabetes mellitus, and preeclampsia. Therefore, understanding the metabolic changes caused by PFOA exposure is of great significance to protect pregnant women from its adverse effects. In this study, the metabolomes from the urine samples of pregnant women exposure to PFOA at different degrees were analyzed by GC-MS and LC-MS. The samples in different groups were distinguished and the differential metabolites were screened based on the VIP value, FC, and P-value of each comparison group through multivariate statistical analysis. The pathways related to differential metabolites were searched to reveal the effects of PFOA exposure on metabolic changes in pregnant women at different degrees. Finally, the ROC of differential metabolites was performed, and the differential metabolites with large area under the curve (AUC) values were selected and compared to identify the mutually differential metabolites. Meanwhile, these metabolites were fitted with a multivariable to explore if they could be used to distinguish different groups. The quantitative comparison of mutually differential metabolites revealed that the levels of L-cysteine, glycine, and 5-aminovaleric acid were positively correlated with the degree of PFOA exposure, indicating that different degrees of PFOA exposure could affect the synthesis or degradation of GSH and change the metabolism of oral or intestinal microbiota. Additionally, they may cause oxidative stress and abnormal fat metabolism in pregnant women.     

Cultivars and oil extraction techniques affect Cd/Pb contents and health risks in oil of rapeseed grown on Cd/Pb-contaminated farmland

● Organic solvent extracted fewer Cd/Pb in rapeseed oil than physical pressing. ● Brassica rapa transferred fewer Cd and Pb from seed to oil than Brassica napus . ● Carcinogenic risk mainly from Cd and worth more concern than noncarcinogenic risk. ● Organic solvent specially SLB pose less heath risk for oil than physical pressing. ● Rapeseed oil posed higher carcinogenic risk for rural residents than urban. Substitute planting with rapeseed offers promise for safely using large areas of Cd/Pb-contaminated farmland. Cd/Pb distributions during rapeseed oil production were investigated and health risks posed by the oil were assessed. Tests were performed using three cultivars (Brassica rapa SYH and ZS100 and Brassica napus QY-1) and four oil extraction techniques (mechanical and low-temperature pressing and n-hexane and subcritical low-temperature butane extraction). The amounts of Cd and Pb in oil were 0.73%–8.44% and 3.14%–11.76%, respectively, of the amounts in rapeseed and were strongly affected by the cultivar and oil extraction technique. The heavy metal (HM) concentrations were lower in solvent-extracted oil (particularly subcritical low-temperature butane extracted oil, in which HMs were not detected) than mechanically pressed oil. The Cd and Pb transfer indices were lower (meaning larger proportions of HMs were retained by the rapeseed meal) for B. rapa than B. napus. This was attributed to a high HM binding protein content of B. rapa seed. Health risks to humans were assessed using a probabilistic risk assessment model. The carcinogenic risk was mainly (97.1%–99.9%) caused by Cd and poses more concern than non-carcinogenic risk. Stronger health risks are posed by mechanically pressed than solvent-extracted oil, and higher carcinogenic risks are posed to people living in rural areas than urban areas. Substitute planting with B. rapa and extracting oil with organic solvent (preferably subcritical low-temperature butane) are optimal for safely utilizing Cd/Pb-contaminated soil. Attention should be paid to the health risks posed by Cd in oil to rural populations.     

Low-temperature caproate production,microbial diversity,and metabolic pathway in xylose anaerobic fermentation

● Converting xylose to caproate under a low temperature of 20 °C by MCF was verified. ● Final concentration of caproate from xylose in a batch reactor reached 1.6 g/L. ● Changing the substrate to ethanol did not notably increase the caproate production. ● Four genera, including Bifidobacterium , were revealed as caproate producers. ● The FAB pathway and incomplete RBO pathway were revealed via metagenomic analysis. Mixed culture fermentation (MCF) is challenged by the unqualified activity of enriched bacteria and unwanted methane dissolution under low temperatures. In this work, caproate production from xylose was investigated by MCF at a low temperature (20 °C). The results showed that a 9 d long hydraulic retention time (HRT) in a continuously stirred tank reactor was necessary for caproate production (~0.3 g/L, equal to 0.6 g COD/L) from xylose (10 g/L). The caproate concentration in the batch mode was further increased to 1.6 g/L. However, changing the substrate to ethanol did not promote caproate production, resulting in ~1.0 g/L after 45 d of operation. Four genera, Bifidobacterium, Caproiciproducens, Actinomyces, and Clostridium_sensu_stricto_12, were identified as the enriched caproate-producing bacteria. The enzymes in the fatty acid biosynthesis (FAB) pathway for caproate production were identified via metagenomic analysis. The enzymes for the conversion of (C_n+2)-2,3-Dehydroxyacyl-CoA to (C_n+2)-Acyl-CoA (i.e., EC 1.3.1.8 and EC 1.3.1.38) in the reverse β-oxidation (RBO) pathway were not identified. These results could extend the understanding of low-temperature caproate production.     

Penicillin fermentation residue biochar as a high-performance electrode for membrane capacitive deionization

● We have provided an activated method to remove the toxicity of antibiotic residue. ● PFRB can greatly improve the salt adsorption capacity of MCDI. ● The hierarchical porous and abundant O/N-doped played the key role for the high-capacity desalination. ● A new field of reuse of penicillin fermentation residue has been developed. Membrane capacitive deionization (MCDI) is an efficient desalination technology for brine. Penicillin fermentation residue biochar (PFRB) possesses a hierarchical porous and O/N-doped structure which could serve as a high-capacity desalination electrode in the MCDI system. Under optimal conditions (electrode weight, voltage, and concentration) and a carbonization temperature of 700 °C, the maximum salt adsorption capacity of the electrode can reach 26.4 mg/g, which is higher than that of most carbon electrodes. Furthermore, the electrochemical properties of the PFRB electrode were characterized through cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) with a maximum specific capacitance of 212.18 F/g. Finally, biotoxicity tests have showed that PFRB was non-biotoxin against luminescent bacteria and the MCDI system with the PFRB electrode remained stable even after 27 adsorption–desorption cycles. This study provides a novel way to recycle penicillin residue and an electrode that can achieve excellent desalination.     

A pyrazine based metal-organic framework for selective removal of copper from strongly acidic solutions

● pz-UiO-66 was synthesized facilely by a solvothermal method. ● Efficient capture of copper from highly acidic solution was achieved by pz-UiO-66. ● pz-UiO-66 exhibited excellent selectivity and capacity for copper capture. ● Pyrazine-N in pz-UiO-66 was shown to be the dominant adsorption site. The selective capture of copper from strongly acidic solutions is of vital importance from the perspective of sustainable development and environmental protection. Metal organic frameworks (MOFs) have attracted the interest of many scholars for adsorption due to their fascinating physicochemical characteristics, including adjustable structure, strong stability and porosity. Herein, pz-UiO-66 containing a pyrazine structure is successfully synthesized for the efficient separation of copper from strongly acidic conditions. Selective copper removal at low pH values is accomplished by using this material that is not available in previously reported metal–organic frameworks. Furthermore, the material exhibits excellent adsorption capacity, with a theoretical maximum copper uptake of 247 mg/g. As proven by XPS and FT-IR analysis, the coordination of pyrazine nitrogen atoms with copper ions is the dominant adsorption mechanism of copper by pz-UiO-66. This work provides an opportunity for efficient and selective copper removal under strongly acidic conditions, and promises extensive application prospects for the removal of copper in the treatment for acid metallurgical wastewater.     

Effect of loading rate on shear strength parameters of mechanically and biologically treated waste

● Mechanical behavior of MBT waste affected by loading rate was investigated. ● Shear strength ratio of MBT waste increases with an increase in loading rate. ● Cohesion is inversely related to loading rate. ● Internal friction angles are positively related to loading rate. ● MBT waste from China shows smaller range of φ. Mechanical biological treatment (MBT) technology has attracted increasing attention because it can reduce the volume of waste produced. To deal with the current trend of increasing waste, MBT practices are being adopted to address waste generated in developing urban societies. In this study, a total of 20 specimens of consolidated undrained triaxial tests were conducted on waste obtained from the Hangzhou Tianziling landfill, China, to evaluate the effect of loading rate on the shear strength parameters of MBT waste. The MBT waste samples exhibited an evident strain-hardening behavior, and no peak was observed even when the axial strain exceeded 25%. Further, the shear strength increased with an increase in the loading rate; the effect of loading rate on shear strength under a low confining pressure was greater than that under a high confining pressure. Furthermore, the shear strength parameters of MBT waste were related to the loading rate. The relationship between the cohesion, internal friction angle, and logarithm of the loading rate could be fitted to a linear relationship, which was established in this study. Finally, the ranges of shear strength parameters cohesion c and effective cohesion c ´ were determined as 1.0–8.2 kPa and 2.1–14.9 kPa, respectively; the ranges of the internal friction angle φ and effective internal friction angle φ ´ were determined as 16.2°–29° and 19.8°–43.9°, respectively. These results could be used as a valuable reference for conducting stability analyses of MBT landfills.     

Relationship between groundwater cadmium and vicinity resident urine cadmium levels in the non-ferrous metal smelting area,China

● This study systematically examined the relationship between groundwater Cd and UCL. ● The study covered 211 UCL and sociological characteristic from nine groundwater samples. ● We found a significant positive correlation between groundwater Cd and UCL. ● Smoking status and education level also significantly affected UCL. Cadmium (Cd) has received widespread attention owing to its persistent toxicity and non-degradability. Cd in the human body is mainly absorbed from the external environment and is usually assessed using urinary Cd. Hunan Province is the heartland of the Chinese non-ferrous mining area, where several serious Cd pollution events have occurred, including high levels of Cd in the urine of residents. However, the environmental factors influencing high urinary Cd levels (UCLs) in nearby residents remain unclear. Therefore, 211 nearby residents’ UCLs and the corresponding sociological characteristics from nine groundwater samples in this area were analyzed using statistical analysis models. Groundwater Cd concentration ranged from 0.02 to 1.15 μg/L, aligning with class III of the national standard; the range of UCL of nearby residents was 0.37–36.60 μg/L, exceeding the national guideline of 0–2.5 μg/L. Groundwater Cd levels were positively correlated with the UCL (P < 0.001, correlation coefficient 95 % CI = 9.68, R² = 0.06). In addition, sociological characteristics, such as smoking status and education level, also affect UCL. All results indicate that local governments should strengthen the prevention and abatement of groundwater Cd pollution. This study is the first to systematically evaluate the relationship between groundwater Cd and UCL using internal and external environmental exposure data. These findings provide essential bases for relevant departments to reduce Cd exposure in regions where the heavy metal industry is globally prevalent.     

The role of lipids in fermentative propionate production from the co-fermentation of lipid and food waste

● Lipid can promote PA production on a target from food waste. ● PA productivity reached 6.23 g/(L∙d) from co-fermentation of lipid and food waste. ● Lipid promoted the hydrolysis and utilization of protein in food waste. ● Prevotella , Veillonella and norank _f _Propioni bacteriaceae were enriched. ● Main pathway of PA production was the succinate pathway. Food waste (FW) is a promising renewable low-cost biomass substrate for enhancing the economic feasibility of fermentative propionate production. Although lipids, a common component of food waste, can be used as a carbon source to enhance the production of volatile fatty acids (VFAs) during co-fermentation, few studies have evaluated the potential for directional propionate production from the co-fermentation of lipids and FW. In this study, co-fermentation experiments were conducted using different combinations of lipids and FW for VFA production. The contributions of lipids and FW to propionate production, hydrolysis of substrates, and microbial composition during co-fermentation were evaluated. The results revealed that lipids shifted the fermentation type of FW from butyric to propionic acid fermentation. Based on the estimated propionate production kinetic parameters, the maximum propionate productivity increased significantly with an increase in lipid content, reaching 6.23 g propionate/(L∙d) at a lipid content of 50%. Propionate-producing bacteria Prevotella, Veillonella, and norank_f_Propionibacteriaceae were enriched in the presence of lipids, and the succinate pathway was identified as a prominent fermentation route for propionate production. Moreover, the Kyoto Encyclopedia of Genes and Genomes functional annotation revealed that the expression of functional genes associated with amino acid metabolism was enhanced by the presence of lipids. Collectively, these findings will contribute to gaining a better understanding of targeted propionate production from FW.     

Highly efficient and selective removal of phosphate from wastewater of sea cucumber aquaculture for microalgae culture using a new adsorption-membrane separation-coordinated strategy

● A new adsorption-membrane separation strategy is used for phosphate removal. ● PVC/Zr-BT shows a selective adsorption ability to low-concentration phosphate. ● Low concentration of P below 0.05 mg/L was achieved in actual wastewater treatment. ● Algal biomass production served as a demonstration of phosphorus recycling. Enhanced phosphorus treatment and recovery has been continuously pursued due to the stringent wastewater discharge regulations and a phosphate supply shortage. Here, a new adsorption-membrane separation strategy was developed for rational reutilization of phosphate from sea cucumber aquaculture wastewater using a Zr-modified-bentonite filled polyvinyl chloride membrane. The as-obtained polyvinyl chloride/Zr-modified-bentonite membrane was highly permeability (940 L/(m²·h)), 1–2 times higher than those reported in other studies, and its adsorption capacity was high (20.6 mg/g) when the phosphate concentration in water was low (5 mg/L). It remained stable under various conditions, such as different pH, initial phosphate concentrations, and the presence of different ions after 24 h of adsorption in a cross-flow filtration system. The total phosphorus and phosphate removal rate reached 91.5% and 95.9%, respectively, after the membrane was used to treat sea cucumber aquaculture wastewater for 24 h and no other water quality parameters had been changed. After the purification process, the utilization of the membrane as a new source of phosphorus in the phosphorus-free f/2 medium experiments indicated the high cultivability of economic microalgae Phaeodactylum tricornutum FACHB-863 and 1.2 times more chlorophyll a was present than in f/2 medium. The biomass and lipid content of the microalgae in the two different media were similar. The innovative polyvinyl chloride/Zr-modified-bentonite membrane used for phosphorus removal and recovery is an important instrument to establish the groundwork for both the treatment of low concentration phosphate from wastewater as well as the reuse of enriched phosphorus in required fields.     

Collaborative control of fine particles and ozone required in China for health benefit

● Increased DAAO offsets 3/4 of the decrease of DAAP in 2013–2020. ● DAAO increases are mainly due to O₃ concentration increase and population aging. ● Health benefit from PM_2.5 reduction after 2017 is larger than that before 2017. ● Reducing PM_2.5 concentration by 1% results in 0.6% reduction of DAAP. ● Reducing O₃ concentration by 1% results in 2% reduction of DAAO. PM_2.5 concentration declined significantly nationwide, while O₃ concentration increased in most regions in China in 2013–2020. Recent evidences proved that peak season O₃ is related to increased death risk from non-accidental and respiratory diseases. Based on these new evidences, we estimate excess deaths associated with long-term exposure to ambient PM_2.5 and O₃ in China following the counterfactual analytic framework from Global Burden Disease. Excess deaths from non-accidental diseases associated with long-term exposure to ambient O₃ in China reaches to 579 (95% confidential interval (CI): 93, 990) thousand in 2020, which has been significantly underestimated in previous studies. In addition, the increased excess deaths associated with long-term O₃ exposure (234 (95% CI: 177, 282) thousand) in 2013–2020 offset three quarters of the avoided excess deaths (302 (95% CI: 244, 366) thousand) mainly due to PM_2.5 exposure reduction. In key regions (the North China Plain, the Yangtze River Delta and the Fen-Wei Plain), the former is even larger than the latter, particularly in 2017–2020. Health benefit of PM_2.5 concentration reduction offsets the adverse effects of population growth and aging on excess deaths attributed to PM_2.5 exposure. Increase of excess deaths associated with O₃ exposure is mainly due to the strong increase of O₃ concentration, followed by population aging. Considering the faster population aging process in the future, collaborative control, and faster reduction of PM_2.5 and O₃ are needed to reduce the associated excess deaths.     

Evaluating the impact of sulfamethoxazole on hydrogen production during dark anaerobic sludge fermentation

● SMX promotes hydrogen production from dark anaerobic sludge fermentation. ● SMX significantly enhances the hydrolysis and acidification processes. ● SMX suppresses the methanogenesis process in order to reduce hydrogen consumption. ● SMX enhances the relative abundance of hydrogen-VFAs producers. ● SMX brings possible environmental risks due to the enrichment of ARGs. The impact of antibiotics on the environmental protection and sludge treatment fields has been widely studied. The recovery of hydrogen from waste activated sludge (WAS) has become an issue of great interest. Nevertheless, few studies have focused on the impact of antibiotics present in WAS on hydrogen production during dark anaerobic fermentation. To explore the mechanisms, sulfamethoxazole (SMX) was chosen as a representative antibiotic to evaluate how SMX influenced hydrogen production during dark anaerobic fermentation of WAS. The results demonstrated SMX promoted hydrogen production. With increasing additions of SMX from 0 to 500 mg/kg TSS, the cumulative hydrogen production elevated from 8.07 ± 0.37 to 11.89 ± 0.19 mL/g VSS. A modified Gompertz model further verified that both the maximum potential of hydrogen production (P_m) and the maximum rate of hydrogen production (R_m) were promoted. SMX did not affected sludge solubilization, but promoted hydrolysis and acidification processes to produce more hydrogen. Moreover, the methanogenesis process was inhibited so that hydrogen consumption was reduced. Microbial community analysis further demonstrated that the introduction of SMX improved the abundance of hydrolysis bacteria and hydrogen-volatile fatty acids (VFAs) producers. SMX synergistically influenced hydrolysis, acidification and acetogenesis to facilitate the hydrogen production.     

Differences in distributions,assembly mechanisms,and putative interactions of AOB and NOB at a large spatial scale

● Nitrifiers in WWTP were investigated at large spatial scale. ● AOB populations varied greatly but NOB populations were similar among cities. ● Drift dominated both AOB and NOB assembling processes. ● DO did not show a significant effect on NOB. ● NOB tended to cooperate with AOB and non-nitrifying microorganisms. Ammonia-oxidizing bacteria (AOB) and nitrite-oxidizing bacteria (NOB) play crucial roles in removing nitrogen from sewage in wastewater treatment plants (WWTPs) to protect water resources. However, the differences in ecological properties and putative interactions of AOB and NOB in WWTPs at a large spatial scale remain unclear. Hence, 132 activated sludge (AS) samples collected from 11 cities across China were studied by utilizing 16S rRNA gene sequencing technology. Results indicated that Nitrosomonas and Nitrosospira accounted for similar ratios of the AOB community and might play nearly equal roles in ammonia oxidation in AS. However, Nitrospira greatly outnumbered other NOB genera, with proportions varying from 94.7% to 99.9% of the NOB community in all WWTPs. Similar compositions and, hence, a low distance–decay turnover rate of NOB (0.035) across China were observed. This scenario might have partly resulted from the high proportions of homogenizing dispersal (~13%). Additionally, drift presented dominant roles in AOB and NOB assembling mechanisms (85.2% and 81.6% for AOB and NOB, respectively). The partial Mantel test illustrated that sludge retention time and temperature were the primary environmental factors affecting AOB and NOB communities. Network results showed that NOB played a leading role in maintaining module structures and node connections in AS. Moreover, most links between NOB and other microorganisms were positive, indicating that NOB were involved in complex symbioses with bacteria in AS.     

Hybrid energy harvesting systems for self-powered sustainable water purification by harnessing ambient energy

● Energy harvesters harness multiple energies for self-powered water purification. ● Hybrid energy harvesters enable continuous output under fluctuating conditions. ● Mechanical, thermal, and solar energies enable synergic harvesting. ● Perspectives of hybrid energy harvester-driven water treatment are proposed. The development of self-powered water purification technologies for decentralized applications is crucial for ensuring the provision of drinking water in resource-limited regions. The elimination of the dependence on external energy inputs and the attainment of self-powered status significantly expands the applicability of the treatment system in real-world scenarios. Hybrid energy harvesters, which convert multiple ambient energies simultaneously, show the potential to drive self-powered water purification facilities under fluctuating actual conditions. Here, we propose recent advancements in hybrid energy systems that simultaneously harvest various ambient energies (e.g., photo irradiation, flow kinetic, thermal, and vibration) to drive water purification processes. The mechanisms of various energy harvesters and point-of-use water purification treatments are first outlined. Then we summarize the hybrid energy harvesters that can drive water purification treatment. These hybrid energy harvesters are based on the mechanisms of mechanical and photovoltaic, mechanical and thermal, and thermal and photovoltaic effects. This review provides a comprehensive understanding of the potential for advancing beyond the current state-of-the-art of hybrid energy harvester-driven water treatment processes. Future endeavors should focus on improving catalyst efficiency and developing sustainable hybrid energy harvesters to drive self-powered treatments under unstable conditions (e.g., fluctuating temperatures and humidity).     

Development of machine learning multi-city model for municipal solid waste generation prediction

● A database of municipal solid waste (MSW) generation in China was established. ● An accurate MSW generation prediction model (WGMod) was constructed. ● Key factors affecting MSW generation were identified. ● MSW trends generation in Beijing and Shenzhen in the near future are projected. Integrated management of municipal solid waste (MSW) is a major environmental challenge encountered by many countries. To support waste treatment/management and national macroeconomic policy development, it is essential to develop a prediction model. With this motivation, a database of MSW generation and feature variables covering 130 cities across China is constructed. Based on the database, advanced machine learning (gradient boost regression tree) algorithm is adopted to build the waste generation prediction model, i.e., WGMod. In the model development process, the main influencing factors on MSW generation are identified by weight analysis. The selected key influencing factors are annual precipitation, population density and annual mean temperature with the weights of 13%, 11% and 10%, respectively. The WGMod shows good performance with R² = 0.939. Model prediction on MSW generation in Beijing and Shenzhen indicates that waste generation in Beijing would increase gradually in the next 3–5 years, while that in Shenzhen would grow rapidly in the next 3 years. The difference between the two is predominately driven by the different trends of population growth.     

Characterization and variation of dissolved organic matter in composting: a critical review

● Effect of composting approaches on dissolved organic matter (DOM). ● Effect of composting conditions on the properties of DOM. ● Character indexes of DOM varied in composting. ● The size, hydrophobicity, humification, and electron transfer capacity increased. ● The hydrophilicity, protein-like materials, and aliphatic components reduced. As the most motive organic fraction in composting, dissolved organic matter (DOM) can contribute to the transfer and dispersal of pollutants and facilitate the global carbon cycle in aquatic ecosystems. However, it is still unclear how composting approaches and conditions influence the properties of compost-derived DOM. Further details on the shift of DOM character indexes are required. In this study, the change in properties of compost-derived DOM at different composting approaches and the effect of composting conditions on the DOM characteristics are summarized. Thereafter, the change in DOM character indexes’ in composting was comprehensively reviewed. Along with composting, the elements and spectral properties (chromophoric DOM (CDOM) and fluorescent DOM (FDOM)) were altered, size and hydrophobicity increased, and aromatic-C and electron transfer capacity were promoted. Finally, some prospects to improve this study were put forward. This paper should facilitate the people who have an interest in tracing the fate of DOM in composting.     

Prediction and cause investigation of ozone based on a double-stage attention mechanism recurrent neural network

● Used a double-stage attention mechanism model to predict ozone. ● The model can autonomously select the appropriate time series for forecasting. ● The model outperforms other machine learning models and WRF-CMAQ. ● We used the model to analyze the driving factors of VOCs that cause ozone pollution. Ozone is becoming a significant air pollutant in some regions, and VOCs are essential for ozone prediction as necessary ozone precursors. In this study, we proposed a recurrent neural network based on a double-stage attention mechanism model to predict ozone, selected an appropriate time series for prediction through the input attention and temporal attention mechanisms, and analyzed the cause of ozone generation according to the contribution of feature parameters. The experimental data show that our model had an RMSE of 7.71 μg/m³ and a mean absolute error of 5.97 μg/m³ for 1-h predictions. The DA-RNN model predicted ozone closer to observations than the other models. Based on the importance of the characteristics, we found that the ozone pollution in the Jinshan Industrial Zone mainly comes from the emissions of petrochemical enterprises, and the good generalization performance of the model is proved through testing multiple stations. Our experimental results demonstrate the validity and promising application of the DA-RNN model in predicting atmospheric pollutants and investigating their causes.     

Effect of Cu-ZSM-5 catalysts with different CuO particle size on selective catalytic oxidation of N,N-Dimethylformamide

● A series of Cu-ZSM-5 catalysts were tested for DMF selective catalytic oxidation. ● Cu-6 nm samples showed the best catalytic activity and N₂ selectivity. ● Redox properties and chemisorbed oxygen impact on DMF catalytic oxidation. ● Isolated Cu²⁺ species and weak acidity have effects on the generation of N₂. N, N-Dimethylformamide (DMF), a nitrogen-containing volatile organic compound (NVOC) with high emissions from the spray industry, has attracted increasing attention. In this study, Cu-ZSM-5 catalysts with different CuO particle sizes of 3, 6, 9 and 12 nm were synthesized and tested for DMF selective catalytic oxidation. The crystal structure and physicochemical properties of the catalyst were studied by various characterization methods. The catalytic activity increases with increasing CuO particle size, and complete conversion can be achieved at 300–350 °C. The Cu-12 nm catalyst has the highest catalytic activity and can achieve complete conversion at 300 °C. The Cu-6 nm sample has the highest N₂ selectivity at lower temperatures, reaching 95% at 300 °C. The activity of the catalysts is determined by the surface CuO cluster species, the bulk CuO species and the chemisorbed surface oxygen species. The high N₂ selectivity of the catalyst is attributed to the ratio of isolated Cu²⁺ and bulk CuO species, and weak acidity is beneficial to the formation of N₂. The results in this work will provide a new design of NVOC catalytic oxidation catalysts.     

Effect of ambient polycyclic aromatic hydrocarbons and nicotine on the structure of Aβ42 protein

● B[a]P, nicotine and phenanthrene molecules altered the secondary structure of Aβ₄₂. ● β-content of the peptide was significantly enhanced in the presence of the PAHs. ● Nicotine made stable cluster with Aβ₄₂ peptide via hydrogen bonds. ● Phenanthrene due to its small size, interfered with the Aβ₄₂ monomer more strongly. Recent studies have correlated the chronic impact of ambient environmental pollutants like polycyclic aromatic hydrocarbons (PAHs) with the progression of neurodegenerative disorders, either by using statistical data from various cities, or via tracking biomarkers during in-vivo experiments. Among different neurodegenerative disorders, PAHs are known to cause increased risk for Alzheimer’s disease, related to the development of amyloid beta (Aβ) peptide oligomers. However, the complex molecular interactions between peptide monomers and organic pollutants remains obscured. In this work, we performed an atomistic molecular dynamics study via GROMACS to investigate the structure of Aβ₄₂ peptide monomer in the presence of benzo[a]pyrene, nicotine, and phenanthrene. Interestingly the results revealed strong hydrophobic, and hydrogen-bond based interactions between Aβ peptides and these environmental pollutants that resulted in the formation of stable intermolecular clusters. The strong interactions affected the secondary structure of the Aβ₄₂ peptide in the presence of the organic pollutants, with almost 50 % decrease in the α-helix and 2 %–10 % increase in the β-sheets of the peptide. Overall, the undergoing changes in the secondary structure of the peptide monomer in the presence of the pollutants under the study indicates an enhanced formation of Aβ peptide oligomers, and consequent progression of Alzheimer’s disease.