甲胺磷生产废水处理试验研究

提出三条处理甲胺磷生产废水的工艺路线：（１）胺化废水脱氨处理,甲基氯化物废水水解处理,然后混合生化处理;（２）胺化废水脱氨处理后与甲基氯化物原水混合一段生化处理;（３）胺化废水脱氨处理后与甲基氯化物原水混合二段生化处理。对影响废水脱氨、有机磷水解率和生化处理效果的各种因素进行了试验研究,分析了甲胺磷废水水解生成物,筛选出生化处理甲胺磷废水的优势菌种。     

Numerical study of heat transfer characteristics of char from waste tire pyrolysis

To investigate heat transfer of char from waste tire pyrolysis, the cooling of char was simulated by the computational fluid dynamics. To scrutinize the heat transfer characteristics, bed height, temperature of cooling wall, and mixing time were selected as calculation parameters. From the results, increasing the char bed height from 0.005 to 0.02 m, the total heat transfer is decreased as from 45.5 to 26.5 J. As the char bed height is further increased from 0.02 to 0.06 m, the total heat transfer is decreased from 26.5 to 9.1 J. The char bed height affects the total heat transfer significantly. The total heat transfer decreases from 15.9 to 14.0 J as the temperature of cooling wall increases from 273.15 to 323.15 K. The total heat transfer mildly depends on the temperature of cooling wall. The particle mixing time increases from 10 to 120 s and the total heat transfer decreases from 28.6 to 22.6 J. It is noted that the particle contact is enhanced between char particles as well as the particles and cooling wall as the particle mixing time decreases. Consequently, heat transfer is augmented.     

Processing and Physical Properties of Plastics Made from Soy Protein Polyester Blends

Blending soy protein with polyesters using a polyvinyllactam as a compatibilizer successfully made soy protein-based plastics. The polyesters used to produce blends included polycaprolactone (PCL) and Biomax (a commercial biodegradable polyester). The blends were processed by compounding extrusion and injection molding. Blends containing soy protein/Biomax-poly(vinyl alcohol) had tensile strengths ranging from 16–22 MPa, with samples containing larger percentages of the synthetic polymer exhibiting greater strengths. Blends made from soy protein, Biomax, and PCL had tensile strengths ranging from 27–33 MPa. All the blends had high Young's moduli but demonstrated brittle characteristics as evident from their low elongations at break, ranging from 1.8–3.1%. Plastics made from soy protein/polyester blends exhibited low water absorption and had good stability under ambient conditions relative to the plastics made from soy protein alone. Blends made from soy protein flour produced plastics with the lowest water absorption.     

浅论吴泾化工总厂的废水治理

叙述了吴泾化工总厂废水排放与治理概况,着重介绍了尿素生产废水、造气含氰废水和变换废水的处理工艺。     

Effect of OH/NCO Molar Ratio on Properties of Soy-Based Polyurethane Networks

Polyurethane networks from soybean oil have a number of valuable properties, which are determined by their chemical composition and cross-linking density. Changing the molar ratio of reacting groups can vary the latter. In this work we have varied the NCO/OH molar ratio (isocyanate index) from 1.05 to 0.40 in a soy polyol/MDI system, and tested physical and mechanical properties. The degree of swelling in toluene increased from 52–206% by decreasing isocyanate index from 1.05–0.4. The sol fractions and network densities determined from swelling in toluene were compared with ones obtained using the network formation theory based on branching processes. The comparison of experimental sol fractions and network densities with those predicted by theory of network formation suggest that 5–10% of bonds are lost in cycles and that high entanglement contributions increase the network densities. Polymers prepared with NCO/OH ratios from 1.05–0.8 were glassy while the others were rubbery, and that was reflected in their properties. Glass transition temperature (DSC) of the networks decreased from 64–7°C, tensile strength from 47–0.3 MPa, and elongation at break increased from 7–232%. The activation energy of the glass transition, determined from dielectric spectra, varied from 222–156 kJ/mol as the molar ratio of NCO to OH groups decreased from 1.05–0.4.     

氯酸盐生产中三废的综合利用

阐述了从氯酸盐生产电解尾气中回收氢、从含铬废水中回收重铬酸钠和用盐泥制内墙涂料等综合利用技术。     

Thermal pyrolysis of fresh and waste fishing nets

Kinetic tests on the pyrolysis of nylon-6 taken from fresh (new) fishing nets and waste fishing nets were conducted using thermogravimetric analysis at heating rates of 0.5, 1.0 and 2.0 degrees C/min. The main region of decomposition of both materials was between 340 and 440 degrees C at each heating rate. The region of decomposition for the nylon-6 from the waste fishing nets was slightly lower than that of the fresh fishing nets. The result shows that the value of activation energies increased from 128 to 433 kJ mol(-1) as the conversion of the pyrolysis reaction increased from 5% to 95%. Nylon-6 from the fresh fishing nets was pyrolyzed in a micro-scale tubing bomb reactor for 60, 80 and 100 min at 440 degrees C. The yield of pyrolyzed gases increased from 3.94 to 5.50 wt% with reaction time. The selectivity to specific hydrocarbons was not detected from the pyrolyzed oil and the carbon number distribution of the pyrolyzed oil was random.     

Probable Effects of Langmuir Circulation Observed on Oil Slicks in the Field

Although the presence of Langmuir circulation (LC) cells is evident from observations in lakes, ponds, and coastal waters, the effects of these cells on oil slicks have received less attention. This paper considers the effects as inferred from field data of LC cells on oil slicks. Examples from observed experimental oil slicks in the field are presented. The importance of these LC cells is discussed from the point of view of oil spill contingency.     

A research note on the recalcitrance of carbon dioxide gas scrubbing compounds to biodegradation processes

A laboratory study was conducted to determine the feasibility of biotreatment of liquid Sulfinol waste stored at a gas treatment facility. Sulfinol is used to scrub impurities from gas generated from both traditional gas extraction and that from hydraulic fracturing processes. Chemical characterization and microbiological assessment showed that cultures of Sulfinol‐degrading microorganisms could be enriched from Sulfinol‐contaminated soil containing saturated concentrations of Sulfinol: a mixture of di‐isopropanolamine (DiPA), sulfolane, and oxazolidone. Based on this initial finding from the enrichment culture study, batch reactors were incubated with inoculants from enrichment cultures containing known numbers of presumptive Sulfinol‐degrading microorganisms. The microbial analyses of liquors from batch reactors showed microbial inhibition and/or loss of viability due to Sulfinol toxicity, even at the lowest Sufinol waste concentration used (5 percent of the original waste). The changes in concentrations of the chemicals in the batch reactor trials were a result of chemical rather than biodegradation processes. Further research is recommended to develop repeatable strategies for biodegrading the constituents of Sulfinol under field conditions.     

Utilization of turkey manure as granular activated carbon: physical, chemical and adsorptive properties

The high availability of large quantities of turkey manure generated from turkey production makes it an attractive feedstock for carbon production. Pelletized samples of turkey litter and cake were converted to granular activated carbons (GACs) by steam activation. Water flow rate and activation time were changed to produce a range of activation conditions. The GACs were characterized for select physical (yield, surface area, bulk density, attrition), chemical (pH, surface charge) and adsorptive properties (copper ion uptake). Carbon physical and adsorptive properties were dependent on activation time and quantity of steam used as activant. Yields varied from 23% to 37%, surface area varied from 248 to 472 m(2)/g and copper ion adsorption varied from 0.72 to 1.86 mmol Cu(2+)/g carbon. Copper ion adsorption greatly exceeded the values for two commercial GACs. GACs from turkey litter and cake show considerable potential to remove metal ions from water.     

污泥灰中磷的湿化学法回收技术研究进展

从污泥灰中磷的提取、磷与重金属的分离和磷产品的制备3方面综述了国内外湿化学法回收污泥灰中磷的研究进展,重点分析了磷提取过程中的各种影响因素,并对今后污泥灰中磷的湿化学法回收技术的研究方向进行了展望。指出:利用萃取的方法将提取液中的无机强酸萃取出来并回收重复利用,可大幅降低酸的消耗量;在回收磷的同时可研究回收不同种类金属的方法,尤其是价值较大的重金属,以进一步提高污泥灰资源的回收价值。     

Anaerobic digestion of the liquid fraction of dairy manure in pilot plant for biogas production: residual methane yield of digestate

The performance of the only dairy manure biogas plant in Cantabria (Northern coast of Spain) was evaluated in terms of liquid-solid separation and anaerobic digestion of the liquid fraction. Screened liquid fraction was satisfactorily treated in a CSTR digester at HRTs from 20 to 10 days with organic loading rates ranging from 2.0 to 4.5 kg VS/(m(3)d). Stable biogas productions from 0.66 to 1.47 m(3)/(m(3)d) were achieved. Four anaerobic effluents collected from the digester at different HRTs were analyzed to measure their residual methane potentials, which ranged from 12.7 to 102.4 L/gVS. These methane potentials were highly influenced by the feed quality and HRT of the previous CSTR anaerobic digestion process. Biomethanization of the screened liquid fraction of dairy manure from intensive farming has the potential to provide up to 2% of total electrical power in the region of Cantabria.     

Solid wastes integrated management in Rio de Janeiro: input-output analysis

This paper analyzes the socioeconomic aspects of solid waste management in Rio de Janeiro. An "input-output" methodology was used to examine how the secondary product resulting from recycling is re-introduced into the productive process. A comparative profile was developed from the state of recycling and the various other aspects of solid waste management, both from the perspective of its economic feasibility and from the social aspects involved. This was done analyzing the greenhouse gas emissions and the decreased energy consumption. The effects of re-introducing recycled raw materials into the matrix and the ensuing reduction of the demand for virgin raw materials was based on the input-output matrix for the State of Rio de Janeiro. This paper also analyzes the energy savings obtained from recycling and measures the avoided emissions of greenhouse gases.     

排烟冷却塔烟气抬升高度的计算分析

华北地区某电厂排烟冷却塔烟气抬升高度的光学照相法实测结果显示,选用S／P模式计算出排烟冷却塔烟气括升高度是合理的。在环境风速小、空气潮湿条件下,采用排烟冷却塔排放方式有利于污染物稀释扩散;在环境风速大、空气干燥、逆温等不利气象条件时,采用排烟冷却塔排放方式,烟气抬升高度较低。     

Thermal conversion of municipal solid waste via hydrothermal carbonization: comparison of carbonization products to products from current waste management techniques

Hydrothermal carbonization (HTC) is a novel thermal conversion process that may be a viable means for managing solid waste streams while minimizing greenhouse gas production and producing residual material with intrinsic value. HTC is a wet, relatively low temperature (180-350 °C) thermal conversion process that has been shown to convert biomass to a carbonaceous residue referred to as hydrochar. Results from batch experiments indicate HTC of representative waste materials is feasible, and results in the majority of carbon (45-75% of the initially present carbon) remaining within the hydrochar. Gas production during the batch experiments suggests that longer reaction periods may be desirable to maximize the production of energy-favorable products. If using the hydrochar for applications in which the carbon will remain stored, results suggest that the gaseous products from HTC result in fewer g CO(2)-equivalent emissions than the gases associated with landfilling, composting, and incineration. When considering the use of hydrochar as a solid fuel, more energy can be derived from the hydrochar than from the gases resulting from waste degradation during landfilling and anaerobic digestion, and from incineration of food waste. Carbon emissions resulting from the use of the hydrochar as a fuel source are smaller than those associated with incineration, suggesting HTC may serve as an environmentally beneficial alternative to incineration. The type and extent of environmental benefits derived from HTC will be dependent on hydrochar use/the purpose for HTC (e.g., energy generation or carbon storage).     

氮肥工业中氨氮废水治理技术进展

介绍了氮肥厂对合成氨低温变换工艺冷凝液和尿素解吸废水的回收处理方法。认为选用热力水解法处理尿素吸废水是可行的。     

Summary of Development and Field Testing of the Transrec Oil Recovery System

This paper summarizes the development, field testing and performance evaluation of the Transrec oil recovery system including the Framo NOFO Transrec 350 skimmer and multi-functional oil spill prevention and response equipment and presents performance data, not published before, from full-scale experimental oil spills in the North Sea from 1981 to 1990. The rare data provides useful information for evaluation of mechanical clean-up capabilities and efficiency, in particular, for responders who are using this equipment in many countries around the world.The development of the Transrec oil recovery system represents one of the most comprehensive efforts funded to date by the oil industry in Norway to improve marine and open ocean oil spill response capabilities. The need for improvements was based upon early practical user experience with different oil recovery systems, and test results from experimental oil spills in the North Sea.The result of the development efforts increased: (1) skimmer efficiency from approximately 15–75% (it reached 100% under favorable environmental conditions); (2) oil emulsion recovery rate from approximately 20–300 m³/h; (3) recovery system efficiency from approximately 15–85% in 1.5 m significant wave height; (4) oil emulsion thickness from approximately 15–35 cm; (5) weather-window for mechanical recovery operations from 1.5 to 3.0 m significant wave height; (6) capability for transfer of recovered oil residue to shuttle tankers in up to 4 m significant wave height and 45 knot winds; (7) capability for operations at night.The new Transrec oil recovery system with the special J-configuration virtually eliminated skimming operation downtime, and damage to booms and equipment failures that had been caused by oil spill response vessel (OSRV) problems with maintaining skimming position in the previous three-vessel oil recovery system with the boom towed in U-configuration. The time required to outfit OSRVs dropped from approximately 30–<1 h, reducing time from notification to operation on site by more than 24 h.Improvement in oil recovery resulted in the acceptance of a new oil spill preparedness and response plan. The new plan reduced the need for oil recovery systems from 21 to 14, towing vessels in preparedness from 42 to 18, and personnel on stand-by from 135 to 70, which subsequently reduced the total contingency and operational costs by almost 50%. These cost reductions resulted from lower contingency fees for personnel, fewer towing vessels on stand-by, less expensive open ocean training and exercises, less equipment and reduced storage space to lease, and simplified equipment maintenance.     

Molecular composition of recycled organic wastes,as determined by solid-state 13C NMR and elemental analyses

Using solid state ¹³C NMR data and elemental composition in a molecular mixing model, we estimated the molecular components of the organic matter in 16 recycled organic (RO) wastes representative of the major materials generated in the Sydney basin area. Close correspondence was found between the measured NMR signal intensities and those predicted by the model for all RO wastes except for poultry manure char. Molecular nature of the organic matter differed widely between the RO wastes. As a proportion of organic C, carbohydrate C ranged from 0.07 to 0.63, protein C from <0.01 to 0.66, lignin C from <0.01 to 0.31, aliphatic C from 0.09 to 0.73, carbonyl C from 0.02 to 0.23, and char C from 0 to 0.45. This method is considered preferable to techniques involving imprecise extraction methods for RO wastes. Molecular composition data has great potential as a predictor of RO waste soil carbon and nutrient outcomes.     

The ART In‐Well Technology test at a chlorinated solvent site in central Iowa

An Accelerated Remediation Technologies (ART) In‐Well Technology pilot test was performed to evaluate the removal of chlorinated volatile organic compounds (VOCs) from groundwater. The ART In‐Well Technology was installed in one well located in the source area where dense nonaqueous‐phase liquid has been identified and VOC concentrations exceed 140,000 μg/L. Monitoring wells at the site were positioned between 10 and 170 feet from the ART test well. Overall, VOC concentrations from samples collected from the groundwater monitoring wells and in the vapors extracted for discharge from the ART treatment well were analyzed over the testing period. Monitoring results showed that concentrations of perchloroethylene were reduced in the closest monitoring well to nondetectable concentrations within 90 days. The cumulative removal of chlorinated VOCs from the ART test well over the six‐month pilot test period exceeded 9,500 pounds based on air monitoring data. The ART technology proved effective and cost‐efficient in reducing contaminant concentrations and removing a large mass of contamination from the subsurface in a short period of time. The radius of influence of the ART technology at the site was estimated to range between 65 and 170 feet. © 2007 Wiley Periodicals, Inc.     

Yttrium recovery from primary and secondary sources: A review of main hydrometallurgical processes

Yttrium is important rare earths (REs) used in numerous fields, mainly in the phosphor powders for low-energy lighting. The uses of these elements, especially for high-tech products are increased in recent years and combined with the scarcity of the resources and the environmental impact of the technologies to extract them from ores make the recycling waste, that contain Y and other RE, a priority.The present review summarized the main hydrometallurgical technologies to extract Y from ores, contaminated solutions, WEEE and generic wastes. Before to discuss the works about the treatment of wastes, the processes to retrieval Y from ores are discussed, since the processes are similar and derived from those already developed for the extraction from primary sources.Particular attention was given to the recovery of Y from WEEE because the recycle of them is important not only for economical point of view, considering its value, but also for environmental impact that this could be generated if not properly disposal.