Study of nitrogen oxide absorption in the calcium sulfite slurry

Experiments were conducted using a bubbling reactor to investigate nitrogen oxide absorption in the calcium sulfite slurry. The effects of CaSO₃ concentration, NO₂/NO mole ratio and O₂ concentrations on NO₂ and SO₂ absorption efficiencies were investigated. Five types of additives, including MgSO₄, Na₂SO₄, FeSO₄, MgSO₄/Na₂SO₄ and FeSO₄/Na₂SO₄, had been evaluated for enhancing NO₂ absorption in CaSO₃ slurry. Results showed that CaSO₃ concentration had significant impact on NO₂ and SO₂ absorption efficiencies, and the highest absorption efficiencies of SO₂ and NO₂ could reach about 99.5 and 75.0 %, respectively. Furthermore, the NO₂ absorption was closely related to the NO₂/NO mole ratio, and the existence of NO₂ in flue gas may promote NO absorption. The presence of O₂ in simulated flue gas was disadvantage for NO _x removal because it can oxidize sulfite to sulfate. It was worth pointing out that FeSO₄/Na₂SO₄ was the best additive among those investigated additives, as the NO₂ removal efficiency was significantly increased from 74.8 to 95.0 %. IC and in situ FTIR results suggest that the main products were NO₃ ^? and NO₂ ^? in liquid phase and N₂O, N₂O₅ and HNO₃ in gas phase during the CaSO₃ absorption process.     

Effects of Nitrogen Deposition on Bryophyte Species Composition of Calcareous Grasslands

Regular additions of NH₄NO₃ (35–140 kg N ha⁻¹ yr⁻¹) and (NH₄)₂SO₄ (140 kg N ha⁻¹ yr⁻¹) to a calcareous grassland in northern England over a period of 12 years have resulted in a decline in the frequency of the indigenous bryophyte species and the establishment of non-indigenous calcifuge species, with implications for the structure and composition of this calcareous bryophyte community. The lowest NH₄NO₃ additions of 35 kg N ha⁻¹ yr⁻¹ produced significant declines in frequency of Hypnum cupressiforme, Campylium chrysophyllum, and Calliergon cuspidatum. Significant reductions in frequency at higher NH₄NO₃ application rates were recorded for Pseudoscleropodium purum, Ctenidum molluscum, and Dicranum scoparium. The highest NH₄NO₃ and (NH₄)₂SO₄ additions provided conditions conducive for the establishment of two typical calcifuges – Polytrichum spp. and Campylopus introflexus, respectively. Substrate-surface pH measurements showed a dose-related reduction in pH with increasing NH₄NO₃ deposition rates of 1.6 pH units between the control and highest deposition rate, and a further significant fall in pH, of >1 pH unit, between the NH₄NO₃ and (NH₄)₂SO₄ treatments. These results suggest that indigenous bryophyte composition may be at risk from nitrogen deposition rates of 35 kg N ha⁻¹ yr⁻¹ or less. These effects are of particular concern for rare or endangered species of low frequency.     

Chemical Recycling of Polyamide Waste at Various Temperatures and Pressures Using High Pressure Autoclave Technique

Chemical recycling of polyamide waste in water was studied using 0.5 L high pressure autoclave at temperatures of 150, 200, 210, 220,230 and 240 °C and at various pressures of 100, 200, 300, 400, 500, 600 and 700 psi (pound per square inch). Viscosity average molecular weight of the polyamide waste sample was determined by Ostwald method and recorded as 1.928 × 10³. The reaction was found to be first order with velocity constant in order of 10⁻² min⁻¹. The velocity constant and percent conversion of depolymerization reaction at 240 °C and 700 psi pressure were recorded as 2.936 × 10⁻² min⁻¹ and 99.99% respectively. The velocity constant was obtained on the basis of measurement of amine value. Kinetic and thermodynamic parameters such as energy of activation, frequency factor, enthalpy of activation were found to be 10.6 kJ mole⁻¹, 0.3719 min⁻¹ and 6.3 kJ mole⁻¹ respectively, at the optimum conditions for maximum depolymerization of polyamide waste.     

Nitrogen Budget of a Spruce Forest Ecosystem After Six-year Addition of Ammonium Sulphate in Southwest Sweden

A nitrogen (N) budget was constructed for a period of 6 years (1988–1993) in a Norway spruce stand with current deposition of 19 kg N and 22 kg S ha⁻¹ year⁻¹. The stand was fertilized annually by addition of 100 kg N and 114 kg S ha⁻¹ (NS). Above and below ground biomass, litterfall, fine- root litter production, soil solution and net mineralization were measured to estimate pools, fluxes and accumulation of nitrogen. The average needle litterfall in control (C) and NS plots in 1993 was 2.2 and 2.5 ton ha⁻¹ year⁻¹, respectively. The fine root litter production prior to treatment (1987) was 4.4 ton ha⁻¹ year⁻¹ and after treatment (1993) it was 4.5 and 3.9 ton ha⁻¹ year⁻¹ in C and NS plots, respectively. Net N mineralization in the soil profile down to 50 cm was estimated to be 86 and 115 kg ha⁻¹ year⁻¹ in C and NS plots, respectively in 1992. During the treatment period the uptake of N in the needle biomass in C and NS plots was 29 and 77 kg ha⁻¹ year⁻¹, respectively. No N was accumulated in needles of C plot where the NS plots accumulated 34 kg ha⁻¹ year⁻¹. Of the annually added inorganic N to NS plots 47% was accumulated in the above and below ground biomass and 37% in the soil. N fluxes via fine-root litter production in the C plots were much higher (54 kg ha⁻¹ year⁻¹) than that via litterfall (29 kg ha⁻¹ year⁻¹). The corresponding values in the NS plots were 65 and 43 kg ha⁻¹ year⁻¹, respectively. Most of the net N mineralization occurred in the FH layer and upper mineral soil. It is concluded that fine root litter and litterfall play an important role in the cycling of N. Despite a high N uptake the losses of N in litterfall and fine root litter resulted in an incorporation of N in soil organic matter.     

The Transit of 35SO4 2- and 3H2O Added In Situ to Soil in a Boreal Coniferous Forest

A solution containing ³⁵SO₄ ^2- and ³H₂O was applied to four plots (5 × 5 m) in a boreal coniferous forest in the Laflamme Lake watershed, Québec, under two contrasting conditions: in summer (plots 1 and 2), and on the snowpack before snowmelt (plots 3 and 4). The transit of both these tracers in the soil solution was then followed through a network of soil lysimeters located at different depths. Four months after the summer application, ³H₂O had infiltrated the whole soil profile at plot 1, while ³⁵SO₄ ^2- was only observed in the LFH and Bhf horizons. A ³⁵SO₄ ^2- budget calculated from mid-August to November indicated that 89 and 10.6% of the added ³⁵SO₄ ^2- was retained within the LFH and the Bhf layers, respectively. Fifteen months later, the added ³⁵SO₄ ^2- was distributed in the following proportions within the soil horizons: LFH (73.7%), Bhf (11.8%) and Bf (12.8%), for a total retention rate of 98.3%. The superficial penetration of ³H₂O at plot 2 was indicative of a major lateral water movement that prevented the calculation of a ³⁵SO₄ ^2- budget. This situation also was observed at plot 4 during snowmelt. At plot 3, ³H₂O moved freely through the soil profile and a significant fraction of the added ³⁵SO₄ ^2- reached the B horizons, where it was presumably adsorbed on aluminum (Al) and ferric (Fe) oxides. The ³⁵SO₄ ^2- budget for plot 3 from March to November indicated that 87% of the added ³⁵SO₄ ^2- was retained within the soil profile, with most being retained in the B horizons (LFH = 33.1%, Bhf = 33.1%, Bf = 20.8%). The contrasting retention patterns of ³⁵SO₄ ^2- within the soil profile following the summer addition and snowmelt likely was caused by the contrastingsoil temperatures and soil solution residence times within the differentsoil layers. The persistence of ³⁵SO₄ ^2- in the soil solution of the entire profile long after the initial tracer infiltration, and the relative temporal stability of specific activity of SO₄ ^2-, point to the establishment of an isotopic equilibrium between the added ³⁵SO₄ and the active S-containing reservoirs within a given soil horizon. Overall, the results clearly illustrate the very strong potential for ³⁵SO₄ ^2- retention and recycling in forest soils.     

Quantification of multiple methane emission sources at landfills using a double tracer technique

A double tracer technique was used successfully to quantify whole-site methane (CH₄) emissions from Fakse Landfill. Emissions from different sections of the landfill were quantified by using two different tracers. A scaled-down version of the tracer technique measuring close-by to localized sources having limited areal extent was also used to quantify emissions from on-site sources at the landfill facility, including a composting area and a sewage sludge storage pit. Three field campaigns were performed. At all three field campaigns an overall leak search showed that the CH₄ emissions from the old landfill section were localized to the leachate collection wells and slope areas. The average CH₄ emissions from the old landfill section were quantified to be 32.6 ± 7.4 kg CH₄ h⁻¹, whereas the source at the new section was quantified to be 10.3 ± 5.3 kg CH₄ h⁻¹. The CH₄ emission from the compost area was 0.5 ± 0.25 kg CH₄ h⁻¹, whereas the carbon dioxide (CO₂) and nitrous oxide (N₂O) flux was quantified to be in the order of 332 ± 166 kg CO₂ h⁻¹ and 0.06 ± 0.03 kg N₂O h⁻¹, respectively. The sludge pit located west of the compost material was quantified to have an emission of 2.4 ± 0.63 kg h⁻¹ CH₄, and 0.03 ± 0.01 kg h⁻¹ N₂O.     

Simulation of substrate degradation in composting of sewage sludge

To simulate the substrate degradation kinetics of the composting process, this paper develops a mathematical model with a first-order reaction assumption and heat/mass balance equations. A pilot-scale composting test with a mixture of sewage sludge and wheat straw was conducted in an insulated reactor. The BVS (biodegradable volatile solids) degradation process, matrix mass, MC (moisture content), DM (dry matter) and VS (volatile solid) were simulated numerically by the model and experimental data. The numerical simulation offered a method for simulating k (the first-order rate constant) and estimating k₂₀ (the first-order rate constant at 20 °C). After comparison with experimental values, the relative error of the simulation value of the mass of the compost at maturity was 0.22%, MC 2.9%, DM 4.9% and VS 5.2%, which mean that the simulation is a good fit. The k of sewage sludge was simulated, and k₂₀, k_20s (first-order rate coefficient of slow fraction of BVS at 20 °C) of the sewage sludge were estimated as 0.082 and 0.015 d^?1, respectively.     

Nutrient release from bisulfate-amended phytase-diet poultry litter under simulated weathering conditions

Poultry litter generated on the Delmarva Peninsula is from phytase-modified bird diet and bisulfate amendment. To establish agronomic application rates in conservation tillage systems, bisulfate-amended phytase-diet poultry litter was investigated for its nutrient release kinetics and supply capacity under simulated weathering conditions. Delmarva poultry litter was packed in PVC columns (15 cm i.d. × 25 cm height) to a depth of 5 cm and leached intermittently with 600 mm of water for 190 days. Concentrations of various nutrients in leachate were analyzed and nutrient release kinetics were modelled. Poultry litter leachate contained high contents of dissolved organic carbon (DOC, 35–11,800 mg L^?1), nitrogen (N 6–2690 mg L^?1), phosphorus (P 45–225 mg L^?1), potassium (K 20–6060 mg L^?1), and other nutrients. Release of the nutrients occurred primarily in the starting 5 weeks and mostly followed a first order Exponential-Rise-to-Maximum model. Under the specified conditions, the poultry litter demonstrated a nutrient supply capacity of 11.7 kg N Mg^?1, 5.4 kg P Mg^?1, and 36.8 kg K Mg^?1. Release of the potentially plant-available N and K was nearly finalized within 190 days of leaching/weathering, but it would require two years for full release of the leachable P. The results indicate that with consideration of field conditions, surface application of bisulfate-amended phytase-diet Delmarva poultry litter at recommended 6.6 Mg ha^?1 to conservation tillage systems would largely provide P 25.0 kg ha^?1, N 106.6 kg ha^?1, and K 245.5 kg ha^?1 to seasonal crops.     

Nitrogen removal from landfill leachate via ex situ nitrification and sequential in situ denitrification

Ex situ nitrification and sequential in situ denitrification represents a novel approach to nitrogen management at landfills. Simultaneous ammonia and organics removal was achieved in a continuous stirred tank reactor (CSTR). The results showed that the maximum nitrogen loading rate (NLR) and the maximum organic loading rate (OLR) was 0.65 g N l^?1 d^?1 and 3.84 g COD l^?1 d^?1, respectively. The ammonia and chemical oxygen demand (COD) removal was over 99% and 57%, respectively. In the run of the CSTR, free ammonia (FA) inhibition and low dissolved oxygen (DO) were found to be key factors affecting nitrite accumulation. In situ denitrification was studied in a municipal solid waste (MSW) column by recalculating nitrified leachate from CSTR. The decomposition of MSW was accelerated by the recirculation of nitrified leachate. Complete reduction of total oxidized nitrogen (TON) was obtained with maximum TON loading of 28.6 g N t^?1 TS d^?1 and denitrification was the main reaction responsible. Additionally, methanogenesis inhibition was observed while TON loading was over 11.4 g N t^?1 TS d^?1 and the inhibition was enhanced with the increase of TON loading.     

Decomposition of dichloromethane and in situ alkali absorption of resulting halogenated products by a packed-bed non-thermal plasma reactor

For an effective decomposition and removal of organic halogenated compounds, a packed-bed non-thermal plasma reactor with in situ absorption of the resulting halogenated products by alkaline sorbent incorporated was proposed. In the plasma reactor, α-Al₂O₃ particles of 1 and 3 mm (mean particle diameter) were packed as solid dielectric medium to enhance the plasma power density in the reactor. Further, alkaline sorbent of Ca(OH)₂ was doped onto the surface of α-Al₂O₃ particles, in order to remove halogenated products by in situ absorption with Ca(OH)₂. A high-voltage and high-frequency pulsed power of −15 to 15 kV and 1 kHz was applied to the wire electrode of the plasma reactor by means of a DC power source. In the present study, as the sample of an organic halogenated compound that is most popularly used, we selected dichloromethane (CH₂Cl₂), and 500 ppm of the initial concentration of CH₂Cl₂ was fed into the reactor accompanied by air at a fixed flow rate of 500 × 10⁻⁶ m³ min⁻¹ at room temperature. As a result, it was recognized that the amount of CH₂Cl₂ decomposed by non-thermal plasma in an α-Al₂O₃ particle bed increased with an increase in plasma input power. The ratio of decomposition of CH₂Cl₂ was almost 100% at 13 kV of electric power and 1 kHz frequency, and CO₂, CH₃Cl, COCl₂, HCl, and Cl₂ were observed as the major reaction products. On the other hand, when CH₂Cl₂ was introduced into the plasma reactor where α-Al₂O₃ particles doped with Ca(OH)₂ were packed, the ratio of decomposition of CH₂Cl₂ became higher, compared to the case that α-Al₂O₃ particles were not doped with Ca(OH)₂. Moreover, there were no halogenated by-product gases detected in the outlet gas from the reactor. As the solid reaction products, CaClOH and Ca(ClO)₂·4H₂O were detected on Ca(OH)₂ by X-ray diffraction. From these findings, it was recognized that CH₂Cl₂ was decomposed more effectively without producing unwanted harmful halogenated by-products in the proposed non-thermal plasma reactor where α-Al₂O₃ particles doped with Ca(OH)₂ sorbent were packed.     

The Influence of Atmospheric N Deposition on Nitrous Oxide and Nitric Oxide Fluxes and Soil Ammonium and Nitrate Concentrations

The deposition of atmospheric N to soils provides sources of available N to the nitrifying and denitrifying microbial community and subsequently influences the rate of NO and N₂O emissions from soil. We have investigated the influence of three different sources of enhanced N deposition on NO and N₂O emissions 1) elevated NH₃ deposition to woodlands downwind of poultry and pig farms, 2) increased wet cloud and occult N deposition to upland forest and moorland and 3) enhanced N deposition to trees as NO ₃ ^– and NH ₄ ⁺ aerosol. Flux measurements of NO and N₂O were made using static chambers in the field or intact and repacked soil cores in the laboratory and determination of N₂O by gas chromatography and of NO by chemiluminescence analysis. Rates of N deposition to our study sites were derived from modelled estimates of N deposition, NH₃ concentrations measured by passive diffusion and inference from measurements of the ²¹⁰Pb inventory of soils under tree canopies compared with open grassland. NO and N₂O emissions and KCl-extractable soil NH ₄ ⁺ and NO ₃ ^– concentrations all increased with increasing N deposition rate. The extent of increase did not appear to be influenced by the chemical form of the N deposited. Systems dominated by dry-deposited NH₃ downwind of intensive livestock farms or wet-deposited NH ₄ ⁺ and NO ₃ ^– in the upland regions of Britain resulted in approximately the same linear response. Emissions of NO and N₂O from these soils increased with both N deposition and KCl extractable NH ₄ ⁺ , but the relationship between NH ₄ ⁺ and N deposition (ln NH ₄ ⁺ = 0.62 ln N_deposition + 0.21, r ² = 0.33, n = 43) was more robust than the relationship between N deposition and soil NO and N₂O fluxes.     

Furniture wood wastes: Experimental property characterisation and burning tests

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected “raw” and primarily “engineered” (“composite”) wood wastes.The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in “engineered” wood wastes as compared with “raw” wood wastes; and relatively high energy content values of “engineered” wood wastes (ranging on the whole from 3675 to 5105 kcal kg⁻¹ for HHV, and from 3304 to 4634 kcal kg⁻¹ for LHV).The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in “engineered” wood burning tests of pyrroles and amines, as well as the additional presence (as compared with “raw” wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon.Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in “engineered” wood burning tests as compared with “raw” wood burning test; and considerable generation of the respirable PM₁ fraction during incomplete industrial wood burning.     

Trends in Water Chemistry in a Maple Forest on a Steep Slope

Year-to-year variation in SO₄ ^2-,NO₃ ^-, Ca²⁺, K⁺, and Mg²⁺concentrations in forest floor and mineral soil percolatefrom a forested, podzolic soil at the Turkey Lakes Watershedon the Precambrian Shield was assessed for monotonic trendsbetween 1986 and 1995. Our objective was to examine howrapidly ion concentrations in soil percolate equilibratedafter stabilization of SO₄ ^2- concentrations inprecipitation. Significant negative trends were detected inmonthly Ca²⁺, and Mg²⁺ concentrations in forestfloor and SO₄ ^2-, Ca²⁺, and Mg²⁺ inmineral soil percolate during the 10-year-period. Thedecline in Ca²⁺ and Mg²⁺ was greater than annualdecreases in SO₄ ^2- and NO₃ ^- in forestfloor percolate and proportional to the reduction inSO₄ ^2- in mineral soil percolate. Response ofmineral soil percolate to a 15 mol_c L^-1SO₄ ^2- decrease in wet-only precipitation between1985 and 1986 was a gradual decline in SO₄ ^2-concentration through 1995. The five-year meanSO₄ ^2- concentration in bulk precipitation, forestfloor percolate, and mineral soil percolate decreased 8, 9and 18 mol_c L^-1 from 1986–90 to 1991–95.Microbial (mineralization of organic S) and sorption(release from and/or retention in the pool of insolubleSO₄ ^2-) processes in the soil were logicalexplanations for the observed changes in SO₄ ^2- inmineral soil percolate.     

Fluxes of NO3-, NH4+, NO,NO2, and N2O in an Old Danish Beech Forest

The fluxes of the major nitrogen compounds havebeen investigated in many ecosystem studies over the world.However, only in few studies has attention been drawn to theimportance of the fluxes of minor gaseous nitrogen compoundsto complete the nitrogen cycle. In Denmark a detailed study onthe nitrogen cycle in an old beech forest has been implementedin 1997 at Gyrstinge near Sorø, Zealand. The study includesthe fluxes of the gases NO, N₂O and water mediatedtransport of NO₃ ^- and NH₄ ⁺. Measurementsof the fluxes of the gaseous compounds are performed withmicro-meteorological methods (eddy-correlation and gradient)and with chambers. Water mediated fluxes encompass rain,throughfall, stem-flow and leaching from the root zone. Thehydrological model is verified by TDR measurements. The findings show that the total water mediated N input tothe forest floor with throughfall and stemflow was 25.6 kg Nha^-1 yr ^-1, and open field wet deposition withprecipitation was 19.0 kg N ha^-1 yr ^-1. The internalcycling of N in the ecosystem measured as turnover oflitterfall and plant uptake was 100 kg N ha^-1 yr ^-1and 14 kg N ha^-1 yr ^-1, respectively. The fluxes ofthe gaseous N compounds NO and N₂O were of minorimportance for the total N turnover in the forest, NO_xemission being <1 kg N ha^-1 yr ^-1 and N₂Oemission from the soil being 0.5 kg N ha^-1 yr ^-1 withno significant difference between wet and dry soils.Concentrations of NO₃ ^- and NH₄ ⁺ in thesoil solution beneath the rooting zone are very small andconsequently the N leaching is almost negligible. It isconcluded that the nitrogen mass balance of this old beechforest ecosystem mainly is controlled by the input by dry andwet deposition and a large internal N cycle with a fast litterturnover. The nitrogen input tothe forest ecosystem which currently exceeds the critical loadby 5 kg N ha^-1 yr ^-1is mainly accumulated in the soil and no significant nitrateleaching is occurring.     

Limits and dynamics of methane oxidation in landfill cover soils

In order to understand the limits and dynamics of methane (CH₄) oxidation in landfill cover soils, we investigated CH₄ oxidation in daily, intermediate, and final cover soils from two California landfills as a function of temperature, soil moisture and CO₂ concentration. The results indicate a significant difference between the observed soil CH₄ oxidation at field sampled conditions compared to optimum conditions achieved through pre-incubation (60 days) in the presence of CH₄ (50 ml l⁻¹) and soil moisture optimization. This pre-incubation period normalized CH₄ oxidation rates to within the same order of magnitude (112-644 μg CH₄ g⁻¹ day⁻¹) for all the cover soils samples examined, as opposed to the four orders of magnitude variation in the soil CH₄ oxidation rates without this pre-incubation (0.9-277 μg CH₄ g⁻¹ day⁻¹).Using pre-incubated soils, a minimum soil moisture potential threshold for CH₄ oxidation activity was estimated at 1500 kPa, which is the soil wilting point. From the laboratory incubations, 50% of the oxidation capacity was inhibited at soil moisture potential drier than 700 kPa and optimum oxidation activity was typical observed at 50 kPa, which is just slightly drier than field capacity (33 kPa). At the extreme temperatures for CH₄ oxidation activity, this minimum moisture potential threshold decreased (300 kPa for temperatures <5 °C and 50 kPa for temperatures >40 °C), indicating the requirement for more easily available soil water. However, oxidation rates at these extreme temperatures were less than 10% of the rate observed at more optimum temperatures (∼30 °C). For temperatures from 5 to 40 °C, the rate of CH₄ oxidation was not limited by moisture potentials between 0 (saturated) and 50 kPa. The use of soil moisture potential normalizes soil variability (e.g. soil texture and organic matter content) with respect to the effect of soil moisture on methanotroph activity. The results of this study indicate that the wilting point is the lower moisture threshold for CH₄ oxidation activity and optimum moisture potential is close to field capacity.No inhibitory effects of elevated CO₂ soil gas concentrations were observed on CH₄ oxidation rates. However, significant differences were observed for diurnal temperature fluctuations compared to thermally equivalent daily isothermal incubations.     

Production costs and operative margins in electric energy generation from biogas. Full-scale case studies in Italy

The purpose of this study was to observe the economic sustainability of three different biogas full scale plants, fed with different organic matrices: energy crops (EC), manure, agro-industrial (Plants B and C) and organic fraction of municipal solid waste (OFMSW) (Plant A). The plants were observed for one year and total annual biomass feeding, biomass composition and biomass cost (€ Mg^?1), initial investment cost and plant electric power production were registered. The unit costs of biogas and electric energy (€ Sm^?3_biogas, € kW h^?1_EE) were differently distributed, depending on the type of feed and plant. Plant A showed high management/maintenance cost for OFMSW treatment (0.155 € Sm^?3_biogas, 45% of total cost), Plant B suffered high cost for EC supply (0.130 € Sm^?3_biogas, 49% of total cost) and Plant C showed higher impact on the total costs because of the depreciation charge (0.146 € Sm^?3_biogas, 41% of total costs). The breakeven point for the tariff of electric energy, calculated for the different cases, resulted in the range 120–170 € MW h^?1_EE, depending on fed materials and plant scale. EC had great impact on biomass supply costs and should be reduced, in favor of organic waste and residues; plant scale still heavily influences the production costs. The EU States should drive incentives in dependence of these factors, to further develop this still promising sector.     

Degradation of Starch–Calcium Carbonate Disposable Packaging in a Solid Waste Composting Facility

The compostability of starch–CaCO₃ disposable packaging was examined in a source-separated municipal solid waste (MSW) composting facility located in East Hampton, NY. Source-separated MSW:starch–CaCO₃ container mixtures of 0 (control), 5, and 20% (by volume) were prepared as feedstock for composting. Compost samples were collected weekly or biweekly during the composting process and examined for fragments of the starch–CaCO₃ containers. Changes in compost quality due to the presence of starch–CaCO₃ containers were assessed by measuring the nutrient and metal content of the three resultant MSW:starch–CaCO₃ composts. Finally, plant growth studies were conducted to examine the composts for possible plant growth inhibition due to the deterioration of the starch–CaCO₃ containers. Results showed that portions of the starch–CaCO₃ containers were not identified in any of the 5 and 20% sieved and characterized compost fractions > 1.3 cm following 1–3 weeks of composting. Mechanical agitation of the waste along with optimum composting conditions were sufficient to initiate the rapid degradation of the starch–CaCO₃ composites. Degradation of starch–CaCO₃ containers did not affect compost nutrient and trace element content. Grass biomass measurements were performed once weekly over 28 days for grass grown in control (0%), 5%, and 20% starch–CaCO₃-containing compost:soil mixtures. Significant differences in grass biomass for these compost:soil mixtures were measured only for the 0 and 20% starch–CaCO₃-containing compost:soil mixtures at 28 days (9.07 vs 11.05 g, respectively; P = 0.046).     

Sonophotocatalytic Degradation of Chitosan in the Presence of Fe(III)/H2O2 System

The degradation of chitosan by means of ultrasound irradiation and its combination with homogeneous photocatalysis (photo-Fenton) was investigated. Emphasis was given on the effect of additive on degradation rate constants. 24 kHz of ultrasound irradiation was provided by a sonicator, while an ultraviolet source of 16 W was used for UV irradiation. To increase the efficiency of degradation process, degradation system was combined with Fe(III) (2.5 × 10⁻⁴mol/L) and H₂O₂ (0.020–0.118 mol/L) in the presence of UV irradiation and the rate of degradation process change from 1.873 × 10⁻⁹−6.083 × 10⁻⁹ mol^1.7 L s⁻¹. Photo-Fenton process led to complete chitosan degradation in 60 min with the rate increasing with increasing catalyst loading. Sonophotocatalysis in the presence of Fe(III)/H₂O₂ was always faster than the respective individual processes. A synergistic effect between ultrasound and ultraviolet irradiation in the presence of Fenton reagent was calculated. The degraded chitosans were characterized by X-ray diffraction (XRD), gel permeation chromatography (GPC) and Fourier transform infrared (FT-IR) spectroscopy and average molecular weight of ultrasonicated chitosan was determined by measurements of intrinsic viscosity of samples. The results show that the total degree of deacetylation (DD) of chitosan change, partially after degradation and the decrease of molecular weight led to transformation of crystal structure. A negative order for the dependence of the reaction rate on total molar concentration of chitosan solution within the degradation process was suggested. Results of this study indicate that the presence of catalyst in the reaction medium can be utilized to reduce molecular weight of chitosan while maintaining the power of irradiated ultrasound and degree of deacetylation.     

The influence of atmospheric n deposition on nitrous oxide and nitric oxide fluxes and soil ammonium and nitrate concentrations

The deposition of atmospheric N to soils provides sources of available N to the nitrifying and denitrifying microbial community and subsequently influences the rate of NO and N₂O emissions from soil. We have investigated the influence of three different sources of enhanced N deposition on NO and N₂O emissions 1) elevated NH₃ deposition to woodlands downwind of poultry and pig farms, 2) increased wet cloud and occult N deposition to upland forest and moorland and 3) enhanced N deposition to trees as NO^? ₃ and NH⁺ ₄ aerosol. Flux measurements of NO and N₂O were made using static chambers in the field or intact and repacked soil cores in the laboratory and determination of N₂O by gas chromatography and of NO by chemiluminescence analysis. Rates of N deposition to our study sites were derived from modelled estimates of N deposition, NH₃ concentrations measured by passive diffusion and inference from measurements of the ²¹⁰Pb inventory of soils under tree canopies compared with open grassland. NO and N₂O emissions and KCl-extractable soil NH⁺ ₄ and NO^? ₃ concentrations all increased with increasing N deposition rate. The extent of increase did not appear to be influenced by the chemical form of the N deposited. Systems dominated by dry-deposited NH₃ downwind of intensive livestock farms or wet-deposited NH⁺ ₄and NO^? ₃ in the upland regions of Britain resulted in approximately the same linear response. Emissions of NO and N₂O from these soils increased with both N deposition and KCl extractable NH⁺ ₄, but the relationship between NH⁺ ₄ and N deposition (ln NH⁺ ₄ = 0.62 ln N_deposition+0.21, r ² = 0.33, n = 43) was more robust than the relationship between N deposition and soil NO and N₂O fluxes.