Preparation of Porous Nanofibers from Electrospun Polyacrylonitrile/Polyvinylidene Fluoride Composite Nanofibers by Inexpensive Salt Using for Dye Adsorption

The high surface area of porous nanofibers enhances their performance for many applications. The present study investigated electrospinning and dye adsorption properties of polymeric nanofibers which were porous by various types of salts. The salt/polyacrylonitrile/polyvinylidene fluoride composite nanofibers were electrospun, and the inexpensive salts such as sodium chloride (NaCl), sodium bicarbonate (NaHCO₃), or calcium chloride (CaCl₂) was used to manufacture the porous fibers. Subsequently, the salt was removed by a selective dissolution, and salt extraction of nanofibers was performed with the solution of hydrochloric acid (10 wt%). Salt/PVDF/PAN and porous PVDF/PAN composite nanofibers have been applied to dye adsorption of solution. The characteristics of nanofibers were studied by Fourier transform infrared microscopy (FTIR) and scanning electron microscopy (SEM) analysis. FTIR showed that the salt was extracted from PVDF/PAN nanofibers successfully, and SEM indicated that many pores were aligned with the nanofibers. The adsorption capacity of salt nanofibers webs and porous nanofibers webs for Basic Blue 41 were compared with each other, and porous fibers were obtained from NaHCO₃ having the highest dye adsorption value. Adsorption of dyes follows the Langmuir isotherm and pseudo-second order kinetics.     

赖氨酸废水的处理和氨回收

对赖氨酸浓废水调 p H沉淀处理后的澄清水进行预处理 :先加入石灰乳 ,搅拌、沉淀 ,SO42 -从 2 0 0 0 0 m g/ L 左右降至 130 0 mg/ L 左右 ,去除率为 94%左右 ,然后进行空气吹脱 ,NH3- N从 5 0 0 0 mg/ L左右降至 80 m g/ L左右 ,去除率 >98%。吹脱出水经厌氧生化处理后 ,再进行空气吹脱 ,NH3- N从 70 0 mg/ L 左右降至 85 mg/ L 左右 ,去除率 >86 %。再吹脱出水与稀废水混合后进行好氧生化和 A/ O、O系统处理 ,出水的 COD<10 0 m g/ L,BOD5<2 0 mg/ L,SS<70 mg/ L,NH3- N<2 5 m g/ L。对浓废水与石灰乳混合后搅拌过程中及两次空气吹脱过程中挥发的 NH3进行回收 ,将其与 H2 SO4反应 ,生成的 (NH4) 2 SO4回用于生产     

g-C_3N_4/C@Bi_2MoO_6复合光催化剂的制备及其光催化活性

通过水热合成法和液相沉积法制备g-C_3N_4/C@Bi_2MoO_6复合光催化剂,并采用X射线衍射、扫描电子显微镜、氮气吸脱附、紫外-可见漫反射等技术对其进行表征。研究了可见光下g-C_3N_4/C@Bi_2MoO_6催化降解罗丹明B(Rh B)的影响因素,并对其光催化反应机理进行初步探讨。实验结果表明:g-C_3N_4掺杂量为60%(w)时g-C_3N_4/C@Bi_2MoO_6的光催化活性最高;在60%g-C_3N_4/C@Bi_2MoO_6的投加量为1.00 g/L、初始Rh B质量浓度为2.50 mg/L、可见光照射150 min的条件下,Rh B的降解率达到97.90%;在g-C_3N_4/C@Bi_2MoO_6光催化降解体系中,h~+和·O_2~-是主要活性物种。     

预氧化聚丙烯腈/g-C3N4光催化降解罗丹明B

以聚丙烯腈(PAN)和g-C_3N_4为原料,采用超声波辅助分散的溶液浸渍法及煅烧法制备了具有共轭结构的预氧化聚丙烯腈/g-C_3N_4复合光催化剂(CPAN/g-C_3N_4),采用XRD、SEM、FTIR、UV-Vis DRS、EIS等技术对光催化剂进行了表征,考察了CPAN/g-C_3N_4对罗丹明B(Rh B)的可见光催化降解性能。结果表明:CPAN与g-C_3N_4具有良好的协同作用,使g-C_3N_4片状结构堆叠体颗粒显著减小,明显增强了光催化剂在全部光谱范围内的光吸收,有效提高了光生电子-空穴分离效率;在PAN与g-C_3N_4质量比为1∶200、煅烧温度250 ℃、煅烧时间1 h条件下所制备的CPAN/g-C_3N_4光催化活性最高,且具有良好的光催化活性稳定性。超氧自由基和光生空穴为CPAN/g-C_3N_4复合光催化剂光降解罗丹明B的主要活性物种。     

冷冻固定化硝化菌去除废水中氨氮的研究

采用聚乙烯醇(PVA)循环冷冻法制备固定化硝化菌颗粒,经活化后在颗粒填充率为9％的三相流化床中进行氨氮废水处理试验。处理低浓度氨氮有机废水(NH3-N质量浓度为75mg／L．COD约为400mg／L,水力停留时间为4h)时,NH3-N去除率约为90％,COD、TIN的去除率可达82％和60％左右;处理高浓度氨氮废水(NH3-N质量浓度450～500mg／L,水力停留时间为20h)时,NH3-N去除率在98％以上,氨氧化产物中NO2^--N质量分数在95％以上,为亚硝酸盐反硝化提供了有利条件。用该法制成的硝化菌颗粒寿命在3个月以上。     

Cu2O-g-C3N4异质结催化剂光催化降解甲基橙

采用水热还原法和高温煅烧法将Cu₂O生长到石墨型氮化碳（g-C₃N₄）表面,制得Cu₂O-g-C₃N₄异质结复合光催化剂。通过XRD、XPS、SEM、TEM、DRS、PL、BET等技术对催化剂进行了表征,研究了Cu₂O-g-C₃N₄降解甲基橙的光催化性能及主要活性物种。实验和表征结果表明： Cu₂O与g-C₃N₄面面接触,两相间化学作用强烈;Cu₂O-g-C₃N₄催化剂能有效利用太阳光,电子-空穴得到有效分离;当n（Cu₂O）∶n（g-C₃N₄）=5∶1时,Cu₂O-g-C₃N₄催化剂的活性最佳,在可见光下反应30 min时,甲基橙降解率达84.1%;Cu₂O-g-C₃N₄具有较好的活性稳定性,重复使用6次,甲基橙降解率降至64.7%;电子-空穴是Cu₂O-g-C₃N₄光催化降解甲基橙的主要活性物种。     

Fe_3O_4-xTiO_2复合光催化剂的制备及其对染料废水的处理效果

采用共沉淀法制备了复合光催化剂Fe_3O_4-xTiO_2。运用XRD、SEM、TEM和UV-Vis DRS等技术对光催化剂进行了表征,并考察了其在太阳光下对茜素红模拟染料废水的光催化降解活性。实验结果表明,当TiO_2与Fe_3O_4的质量比为0.75、初始溶液p H为3.0时,茜素红去除率最高,光催化反应120 min后,茜素红去除率为100%。表征结果显示,Fe_3O_4-0.75TiO_2复合光催化剂不是核壳结构,而是Fe_3O_4和TiO_2的聚集体。Fe_3O_4-0.75TiO_2复合光催化剂重复使用5次后茜素红去除率几乎没有下降,活性稳定性极佳。     

Nitrogen Saturation of Terrestrial Ecosystems: Some Recent Findings and Their Implications for Our Conceptual Framework

The consequences of nitrogen (N) enrichment for terrestrial and freshwater ecosystems are of increasing concern in many areas due to continued or increasing high emission rates of reactive N. Within terrestrial ecosystems various conceptual frameworks and modelling approaches have been developed which have enhanced our understanding of the sequence of changes associated with increased N availability and help us predict their future impacts. Here, some recent findings are described and their implications for these conceptual frameworks and modelling approaches discussed. They are: (a) an early loss of plant species that are characteristic of low N conditions as N availability increases and a loss of species with high N retention efficiencies (so called N ‘filters’), (b) suppression of microbial immobilisation of deposited due to increased availability in the early stages of N saturation, (c) the early onset of leaching due to these changes (a and b above) in both plant and microbial functioning, (d) reduced sensitivity of vegetation to N additions in areas with high historical N deposition, (e) delayed changes in soil C:N changes due to increased net primary productivity and reduced decomposition of soil organic matter. Some suggestions of early indicators of N saturation are suggested (occurrence of mosses; ratio in surface soils) which indicate either a shift in ecosystem function and/or structure.     

Effect of C/N on composting of pig manure with sawdust

The aim of this composting trial was to evaluate the effect of C/N on the composting process of pig manure with the purpose of reducing the amount of sawdust normally used as co-composting materials. Two aerobic static piles were prepared consisting of pig manure mixed with sawdust at an initial C/N of 30 (pile A) and 15 (pile B), respectively. Pile B containing larger amount of pig manure showed a slower rise in temperature, lower maximum temperature, and shorter thermophilic phase than pile A. It also resulted in higher pH and electrical conductivity (EC) values, and even higher contents of soluble NH4-N and volatile solids throughout the composting period. Chemical and biological parameters including dissolved organic carbon (DOC) (4932 mg kg(-1)), soluble NH4-N (371 mg kg(-1)), C/Nsolid (18.3), C/Naquoeus (5.8) and seed germination index (GI) (66.5%) indicated that pile A achieved maturity after 49 days of composting. After 63 days of composting, pile B contained 5352 and 912 mg kg(-1) of DOC and soluble NH4-N content, respectively, which was much higher than the criterion of 5% and 400 mg kg(-1), indicating its immature nature. Pile B showed a relatively low GI value of 46%, which may be due to its high indigenous EC value as a result of larger amount of pig manure. Therefore, co-composting of pig manure with sawdust at a low initial C/N would require a composting longer than 63 days, and, the high salinity due to the large amount of pig manure would pose a potential inhibition on plant growth.     

不同原料生物炭对NH4+-N、PO43--P吸附性能的差异性及其成因分析

以芦苇、小麦秸秆和竹子为原料,利用回流式炭化工艺制备3种生物炭。比较三者对NH_4~+-N、PO_4~(3-)-P的吸附性能,并对三者吸附性能差异的成因进行分析。实验结果表明:3种生物炭对PO_4~(3-)-P的吸附效果整体上优于NH_4~+-N,因为3种生物炭的阳离子交换容量CEC值和Zeta电位绝对值的水平均较低,不利于阳离子的吸附;竹炭Z-C对NH_4~+-N的吸附效果最佳,6 h去除率为3.59%,低的N含量、pH及Zeta电位绝对值对NH_4~+-N的吸附有利;芦苇炭LW-C中的O更多地与K、Mg等结合,形成能够与PO_4~(3-)反应生成磷酸盐沉淀或者晶体物质的金属氧化物,从而具有最好的PO_4~(3-)-P的吸附效果,6 h时去除率达16.91%。     

清洗液和阻垢剂对疏水膜接触角的影响

研究了采用不同pH的酸、碱清洗液及阻垢剂溶液静态浸泡对聚偏氟乙烯(PVDF)和聚四氟乙烯(PTFE)疏水平板膜接触角的影响.实验结果表明:随pH 2.5盐酸和pH2.0草酸浸泡PVDF膜和PTFE膜时间的延长,两种疏水膜的接触角均小幅度减小,说明酸性清洗液对两种疏水膜性能的影响较小;随pH11.5NaOH溶液浸泡膜时间...     

Fe3O4-MnO2复合材料催化降解水中有机污染物的研究进展

综述了Fe₃O₄-MnO₂复合材料催化降解水中有机污染物的研究进展,介绍了Fe₃O₄-MnO₂复合材料的负载方式,总结了Fe₃O₄-MnO₂复合材料在催化降解水中有机污染物方面的应用。同时,阐述了Fe₃O₄-MnO₂复合材料催化降解水中有机污染物的机理。指出：Fe₃O₄-MnO₂复合材料未来的研发方向是实现负载方式的多样性和提高复合材料的热稳定性,制备出形貌多样、结晶性能好、稳定性高、经济性好、功能多样的Fe₃O₄-MnO₂复合材料。     

ZnFe_2O_4/AC脱硫剂再生方法的比较

采用水洗再生、N_2及N_2+NH_3气氛下的热再生以及微波辐射再生的方式对饱和ZnFe_2O_4/活性炭(AC)脱硫剂进行再生,并通过SEM,XRD,TG等技术进行表征。实验结果表明:水洗温度为90℃时,第一次水洗后ZnFe_2O_4/AC脱硫剂对SO_2的吸附容量(硫容)为122.0 mg/g;N_2氛围下热再生的最佳温度为500℃,ZnFe_2O_4/AC脱硫剂的硫容可达97.2 mg/g;N_2+NH_3氛围下热再生的最佳温度为400℃,ZnFe_2O_4/AC脱硫剂的硫容达到101.2 mg/g;当微波功率为100 W时,ZnFe_2O_4/AC脱硫剂的硫容为87.2 mg/g。对比三种再生方式,一次水洗再生具有更好的再生效果。     

Fe3O4-PTFE电极制备条件和双阴极电-Fenton反应条件的优化

制备了Fe₃O₄-聚四氟乙烯（PTFE）电极,优化了原料配比和焙烧温度。对比了Fe₃O₄-PTFE单阴极和Fe₃O₄-PTFE与乙炔碳黑-PTFE电极并联双阴极体系对模拟Rhb染料废水的处理效果。实验结果表明：在m（Fe₃O₄）∶m（PTFE）=3.0∶2.5、焙烧温度为300 ℃的条件下制备Fe₃O₄-PTFE电极,采用阴极电-Fenton法降解模拟Rhb废水的效果最佳,电解反应120 min时Rhb降解率达86.91%;Fe₃O₄-PTFE电极与乙炔碳黑-PTFE电极并联作为双阴极电解Rhb废水时,最佳电压为6 V,最佳初始废水pH为3,在此条件下电解反应120 min时Rhb降解率达91.65%。     

CePO4-TiO2固溶体的NH3-SCR活性

采用共沉淀法合成了不同Ce与Ti摩尔比的CePO₄-TiO₂复合材料,利用XRD、TEM、NH₃-TPD和H₂-TPR技术对其物理化学性质进行了表征,并对其NH₃-SCR活性进行了评价。实验结果表明：随着CePO₄含量的增加,催化剂的活性提高;当Ce与Ti的摩尔比为8:2时催化剂的活性最高,230 ℃的NO转化率达到100%,且具有更广的温度窗口,优于纯CePO₄。表征结果显示,CePO₄与TiO₂形成固溶体后,颗粒尺寸较为均匀,强酸位的数量增多,氧化还原性能提升,从而提高了催化剂的SCR反应活性,同时改善了其抗水抗硫性能。     

Effect of amendments on windrow composting of sugar industry pressmud

Bioconversion of sugar and distillery industrial wastes with other biodegradables into enriched compost is an important possibility in need of research. In this paper, changes in temperature and physico-chemical (pH, NH4+-N, C/N ratio, CEC) parameters during windrow composting, related to biological stabilization of the compost, were studied. The rise in temperature, which occurred as composting progressed, was accompanied by an increase in NH4+-N and the passage of the thermophilic phase to mesophilic took place between 90 and 105 days. This overall pattern was observed in all composting mixes, whereby the concentrations of NH4+-N increased rapidly and then declined gradually over the course of monitoring pari passu with increase in NO3- -N. The C/N ratios of the composting mixes decreased substantially by the 90th day in full thermophilic phase and became comparatively stable later on. Addition of additives showed potential in improving the C/N ratios. Increases in cation exchange capacity (CEC) and the germination index value of a sensitive crop (Raphanus sativus) had value in establishing the optimum degree of maturity. The rise and fall of temperature and changes in NH4+-N concentrations, C/N ratios and CEC over time proved to be reliable indicators of the progress of the composting process for establishing biological stability and compost maturity.     

石墨相氮化碳协同UV-H_2O_2光催化降解亚甲基蓝

以三聚氰胺为前驱体,经热解—回流法制备了石墨相氮化碳(g-C3N4),采用XRD、FTIR、SEM、EDS、PL等技术对g-C_3N_4进行了表征。研究了g-C_3N_4在UV-H_2O_2体系中对废水中亚甲基蓝(MB)的光降解效果。实验结果表明,UV+g-C_3N_4催化剂+H_2O_2体系能协同降解MB,在初始MB质量浓度为20 mg/L、初始废水p H为5、废水体积为250 mL、g-C_3N_4加入量为0.10 g、H_2O_2浓度为0.4 mmol/L、反应温度为25℃的优化工艺条件下,紫外光照射70 min时MB脱色率达98.32%。g-C_3N_4催化剂具有较好的重复使用性能,使用5次后MB脱色率仍保持在95.10%。     

低浓度氨氮废水的厌氧氨氧化研究

采用污泥混合接种的方法,利用UASB反应器进行厌氧氨氧化菌混培物的培养与驯化,反应器连续运行了210d。当含氮模拟废水进水NH3-N浓度和NO2^--N浓度分别为3～5mmol／L和4～6mmol／L时,其最大去除率分别达68．0％和95．1％。扫描电镜结果表明,厌氧氨氧化菌混培物以形状不规则的短杆菌为主。     

单宁为模板制备纳米二氧化钛 及其对钍的吸附性能

以杨梅单宁(BT)为模板,水热法合成纳米二氧化钛(BT-NTO)。采用XRD、FTIR、SEM和TEM技术对BT-NTO的结构及形貌进行了表征。将BT-NTO用于吸附溶液中的Th~(4+),在溶液pH为3.5、温度为25℃、Th~(4+)初始浓度为0.5 mmol/L的条件下,BT-NTO对Th~(4+)的吸附量为0.905 8 mmol/g;吸附过程符合准二级动力学方程和Langmuir等温吸附方程;溶液中共存的Zn~(2+)、Ni~(2+)、Co~(2+)、Sr~(2+)、Yb~(3+)、Nd~(3+)、Sm~(3+)、Gd~(3+)、La~(3+)、Cl-、ClO4-离子对Th~(4+)吸附量影响较小;BT-NTO的重复使用性能较好。     

磁性CuS/γ-Fe2O3复合材料光催化处理染料废水

以氯化铜、纳米γ-Fe₂O₃和硫脲为原材料,乙二醇为溶剂,采用溶剂热法制备了磁性CuS/γ-Fe₂O₃复合光催化剂。考察了该光催化剂对刚果红染料废水的处理效果。在m（CuS）:m（γ-Fe₂O₃）=2:1、刚果红初始质量浓度为10 mg/L、光催化剂投加量为0.6 g/L的最佳工艺条件下,刚果红去除率达96.51%。阴离子Cl^-、NO₃^- 及SO₄^2-对该光催化剂的催化活性具有促进作用,其中SO₄^2–的促进作用最显著。该光催化剂具有较好的活性稳定性,重复使用6次后刚果红去除率仍高达90.50 %。