Solid waste management techniques for the waste generated and brought down from campsites in the hill spots, trails and expedition tops.

The increasing self-generated solid waste from the visitors in the hill towns, trails and expedition tops is one of the most adverse forms of human impacts in mountain environments. The direct managing authorities, such as municipalities in the hill spots, have no proper places to dispose of municipal waste nor the other infrastructure required nor adequate funds. The trekking and expedition areas are entirely dependent on the moral responsibilities of the local people, as well as visitors, because these locations are in remote areas, outside municipal boundaries. Based on five major case studies representing the Himalayas, the status of solid waste generation, its physical composition and management options in tourist [Kullu: 1,219 metres above average sea level (m), Rewalsar: 1,300 m, Manali: 2,050 m], trekking (in and around the Valley of Flowers: 1,830-4,330 m) and expedition areas (Pindari valley: 2,300-5,500 m) were studied. The inflow of visitors ranged from 150,000 to 1,140,251 in the hill spots, and from 25,000 to 116,392 in the expedition and trekking areas, respectively. The capita = t day 1 waste generation varied from 200-300 g in hill spots and from 200-288 g in expedition and trekking areas, respectively. Biodegradable waste varied from 65.2 to 83.1% of the total waste generated and was of greater quantity than non-biodegradable waste in expedition areas. Non-biodegradable waste was the predominant form in the expedition (66.4%) and trekking areas (84.5%). The ultimate aim of the study is to make the concerned local people, visitors and government aware of the need to harness energy from waste. This can be done in various ways including biocomposting, and the reuse and recycling of waste otherwise considered valueless and useless.     

The impact of tourism on municipal solid waste generation: The case of Menorca Island (Spain)

Tourism can sustain high levels of employment and income, but the sector is a source of environmental and health impacts. One of the most important is the generation of municipal solid waste (MSW). However, there is a lack of studies which quantify how much the tourist population engages in total MSW and separately collected recyclables. The aim of this paper is to estimate the impact of the tourist population on MSW, both total and separately collected, for the period 1998–2010, for the Mediterranean island of Menorca (Spain). We use dynamic regressions models, including data for monthly stocks of tourists. The results show that, on average, a 1% increase in the tourist population in Menorca causes an overall MSW increase of 0.282% and one more tourist in Menorca generates 1.31 kg day^?1 (while one more resident generates 1.48 kg day^?1). This result could be useful to better estimate the seasonal population of different regions, since intrannual fluctuation of MSW is used as a proxy measure of actual population (the sum of residents and tourists). Moreover, an increase of 1% in the tourist population causes an increase of 0.232% in separately collected recyclables and an additional tourist generates 0.160 kg day^?1. One resident selectively collects on average 47.3% more than one tourist. These results can help in the planning of waste infrastructure and waste collection services in tourist areas.     

Sampling household waste at source: lessons learnt in Gaborone.

Municipal solid waste (MSW) quantity and composition analysis is fundamental for the planning of municipal waste management services. The purpose of this paper is to report the results and experiences of sampling household waste at the source of generation in Gaborone, Botswana. The average generation rate, in kg capita(-1) day(-1), and percentages of various components of waste in Gaborone were determined using a statistically designed household sampling survey. The survey covered 47 households with different socio-economic characteristics over 21 days with 893 samples obtained. The results showed that the average waste generation rate for Gaborone was 0.33 kg capita(-1) day(-1). Contrary to common belief, the waste generation rate measured as in weight units was found not be directly related to household income. However, the packaging fractions of plastic and paper measured as volume had a direct relationship with household income. Across all income groups, the putrescible waste fraction constituted the highest proportion of the waste stream at approximately 68%. The main general conclusion is on the importance of practical considerations. As much as statistically designed sampling procedures provide a useful means of estimating the quantity and composition of household waste at source of generation, there are some practical issues that should be carefully considered during sampling to improve the accuracy and relevance of the results.     

Estimating the quantity of solid waste generation in Oyo, Nigeria.

The study established waste multipliers that could be used in conjunction with the population figure of a city to estimate the quantity of solid waste generation in the developing world. Oyo, a traditional city in Nigeria was the focus of the study. Two sets of data were collected. The first was the information on the socio-economic attributes of residents obtained from 648 households through questionnaires administered using a systematic random sampling technique. The second was the measurement of waste generated in 25% of the households for a week in each of the 12 months of the year. The study established that 23.3% of the residents surveyed have educational qualifications beyond secondary school, with 51.2% engaged in occupations requiring very little or no formal education and 50.9% were in the low-income group. The daily per capita solid waste generation was 0.129 kg. The highest (9.8%) and lowest (6.5%) of the annual quantities of waste were produced in October and February, respectively. Similarly, 20.2% of the weekly generation was produced on Saturday and the 10.2% produced on Thursday was the lowest. Animal dung, which accounted for 18.0%, constituted the highest component of the total solid waste generated. The study further established that the organic component of the waste generation was 75.4%. The results of the regression analysis R2 significant at 0.001 showed that income, household size, social status, occupation, education and season of the year explained 88.8% of waste generation in Oyo. It was established that 50.90 tonnes of solid waste was generated per day in the city in 2005, and the daily generation in the year 2008 is estimated to be 55.20 tonnes. The study concluded that with an average annual population growth of 13 000 people for the town, an additional 1.3 acres of land will need to be legally acquired annually, implying that 10.92-19.68 hectares ill be required as dump site(s) over the next 20-30 years.     

Report: Treatment of medical waste in Nisava and Toplica districts, Serbia

If there are no clearly defined management procedures, medical waste may represent a source of serious health hazards. Medical waste management was evaluated at the three hospitals in the Nisava and Toplica district, in Serbia. All the stages of existing waste management (segregation, collection, storage, transportation and disposal of waste) were examined by interviewing the personnel involved in the management of waste. The generated waste was a mixture of hazardous and non-hazardous waste. The study found that waste management performance in this district was poor and that there were problems in every stage of management. The results indicate that the waste generation rate was 1.92 kg bed(-1) day(-1) and consisted of 98.7% general waste and 1.3% sharps. Inappropriate segregation practices were the biggest problem and led to increased quantities of general waste. There were no specific regulations for the segregation of the medical waste. None of the surveyed hospitals have a system to refine wastewater and there were no training courses about hospital waste management.     

Wet landfill decomposition rate determination using methane yield results for excavated waste samples

An increasing number of landfills are operated to accelerate waste decomposition through liquids addition (e.g., leachate recirculation) as a wet landfill. Landfill design and regulation often depend on utilizing landfill gas production models that require an estimate of a first-order gas generation rate constant, k. Consequently, several studies have estimated k using collected gas volumes from operating wet landfills. Research was conducted to examine an alternative approach in which k is estimated not from collected landfill gas but from solid waste samples collected over time and analyzed for remaining gas yield. To achieve this goal, waste samples were collected from 1990 through 2007 at two full-scale landfills in Florida that practiced liquids addition. Methane yields were measured from waste samples collected over time, including periods before and after leachate recirculation, and the results were applied to a first-order decay model to estimate rate constants for each of the sites. An initial, intensive processing step was conducted to exclude non-biodegradable components from the methane yield testing procedure. The resulting rate constants for the two landfills examined were 0.47 yr(-1) and 0.21 yr(-1). These results expectedly exceeded the United States Environmental Protection Agency's rate constants for dry and conventional landfills (0.02-0.05 yr(-1)), but they are comparable to wet landfill rate constants derived using landfill gas data (0.1-0.3 yr(-1)).     

Seasonal characterization of municipal solid waste (MSW) in the city of Chihuahua,Mexico

Management of municipal solid waste (MSW) has become a significant environmental problem, especially in fast-growing cities. The amount of waste generated increases each year and this makes it difficult to create solutions which due to the increase in waste generation year after year and having to identify a solution that will have minimum impact on the environment. To determine the most sustainable waste management strategy for Chihuahua, it is first necessary to identify the nature and composition of the city’s urban waste. The MSW composition varied considerably depending on many factors, the time of year is one of them. Therefore, as part of our attempt to implement an integral waste management system in the city of Chihuahua, we conducted a study of the characteristics of MSW composition for the different seasons. This paper analyzes and compares the findings of the study of the characterization and the generation of solid waste from households at three different socio-economic levels in the city over three periods (April and August, 2006 and January, 2007).The average weight of waste generated in Chihuahua, taking into account all three seasons, was 0.592 kg capita^?1 day^?1. Our results show that the lowest income groups generated the least amount of waste. We also found that less waste was generated during the winter season. The breakdown for the composition of the waste shows that organic waste accounts for the largest proportion (45%), followed by paper (17%) and others (16%).     

Non-hazardous waste generation characteristics and recycling practices in Saskatchewan and Manitoba,Canada

The paper presents the results on the analysis of non-hazardous waste generation characteristics and recycling practices in Saskatchewan (SK) and Manitoba (MB) using the biennial waste reports published by Statistic Canada. The objectives are to examine the waste generation rates from both residential and non-residential sources from 1998 to 2010, and to evaluate the effectiveness of their recycling programs and regulations. In spite of the many similarities between the provinces, MB on average generated 17.5 % more residential waste than SK, and about 15 % less non-residential waste than SK during the study period. It appears that MB waste generation characteristics were very different from SK and the rest of Canada. The amount of MSW generation in MB was, to a certain degree, independent from the economic factors. Assuming status quos conditions, the linear models predicted that the per capita MSW generations in MB would be about 33 % lower than SK in 2020. Data from this study suggest that (1) curbside recycling programs and (2) pay-as-you-throw collection systems may be important factors for increasing diversion rate in SK. It is also found that the non-residential waste generation in Canada was substantially larger than the residential waste generation during the 13-year period.     

Hazardous medical waste generation rates of different categories of health-care facilities

Goal of this work was to calculate the hazardous medical waste unit generation rates (HMWUGR), in kg bed(-1)d(-1), using data from 132 health-care facilities in Greece. The calculations were based on the weights of the hazardous medical wastes that were regularly transferred to the sole medical waste incinerator in Athens over a 22-month period during years 2009 and 2010. The 132 health-care facilities were grouped into public and private ones, and, also, into seven sub-categories, namely: birth, cancer treatment, general, military, pediatric, psychiatric and university hospitals. Results showed that there is a large variability in the HMWUGR, even among hospitals of the same category. Average total HMWUGR varied from 0.012 kg bed(-1)d(-1), for the public psychiatric hospitals, to up to 0.72 kg bed(-1)d(-1), for the public university hospitals. Within the private hospitals, average HMWUGR ranged from 0.0012 kg bed(-1)d(-1), for the psychiatric clinics, to up to 0.49 kg bed(-1)d(-1), for the birth clinics. Based on non-parametric statistics, HMWUGR were statistically similar for the birth and general hospitals, in both the public and private sector. The private birth and general hospitals generated statistically more wastes compared to the corresponding public hospitals. The infectious/toxic and toxic medical wastes appear to be 10% and 50% of the total hazardous medical wastes generated by the public cancer treatment and university hospitals, respectively.     

A baseline study characterizing the municipal solid waste in the State of Kuwait

This paper provides a new reference line for municipal solid waste characterization in Kuwait. The baseline data were collected in accordance with the Standard Test Method for the Determination of the Composition of Unprocessed Municipal Solid Waste (ASTM). The results indicated that the average daily municipal waste generation level is 1.01 kg/person. Detailed waste stream surveys were conducted for more than 600 samples of municipal solid waste (MSW). The waste categories included paper, corrugated fibers, PET bottles, film, organic matter, wood, metal, glass, and others. The results indicated that organic waste dominated the characterization (44.4%), followed by film (11.2%) and then corrugated fibers (8.6%). Analysis of variance (ANOVA) was used to investigate the influence of season and governorate on waste composition. A significant seasonal variation was observed in almost all waste categories. In addition, significant differences in proportions between the current level and 1995 baseline were observed in most waste categories at the 95% confidence level.     

Characterization of urban solid waste in Chihuahua, Mexico

The characterization of urban solid waste generation is fundamental for adequate decision making in the management strategy of urban solid waste in a city. The objective of this study is to characterize the waste generated in the households of Chihuahua city, and to compare the results obtained in areas of the city with three different socioeconomic levels. In order to identify the different socioeconomic trends in waste generation and characterization, 560 samples of solid waste were collected during 1 week from 80 households in Chihuahua and were hand sorted and classified into 15 weighted fractions. The average waste generation in Chihuahua calculated in this study was 0.676 kg per capita per day in April 2006. The main fractions were: organic (48%), paper (16%) and plastic (12%). Results show an increased waste generation associated with the socioeconomic level. The characterization in amount and composition of urban waste is the first step needed for the successful implementation of an integral waste management system.     

Comparative analysis of hazardous household waste in two Mexican regions

Household hazardous waste (HHW) generation in two Mexican regions was examined, a northern region (bordering with the USA) and a central region. The aim of this work was to determine the dynamics of solid waste generation and to be able to compare the results of both regions, regarding consumption patterns and solid waste generation rates. In the northern region, household solid waste was analysed quantitatively. In order to perform this analysis, the population was categorized into three socioeconomic strata (lower, middle, upper). Waste characterization revealed the presence of products that give origin to household hazardous waste. In the northern region (Mexicali city), household hazardous waste comprised 3.7% of municipal solid waste, the largest categories in this fraction were home care products (29.2%), cleaning products (19.5%) and batteries and electronic equipment (15.7%). In the central region, HHW comprised 1.03% of municipal solid waste; the main categories in this fraction were represented by cleaning products (39%), self care products (27.3%), and insecticides (14.4%). In Mexicali, the socioeconomic study demonstrated that the production of HHW is independent of the income level. Furthermore, the composition of the solid waste stream in both regions suggested the influence of another set of variables such as local climate, migration patterns and marketing coverage. Further research is needed in order to establish the effect of low quantities of HHW upon the environment and public health.     

Waste management options in southern Europe using field and experimental data

The applicability of the Waste Management Hierarchy concept that appeared to be an essential element in current national environmental policies was investigated in the case of a region in Southern Europe. The waste generation profile that determines the appropriateness of different waste management options was created after a 1-year municipal waste sampling investigation conducted in the Municipality of Pilea in Northern Greece. The paper describes the results of (1) the sampling method, which was conducted four times during 1 year (once per season) in selected areas of the city, (2) the qualitative analysis of the collected samples and (3) the waste treatment, which consisted of drying, grinding, calorific value measurement, incineration and chemical analysis of the collected samples. Comparative analysis between the above mentioned data and on past data derived from investigations conducted in other Greek regions with similar characteristics to those of Pilea were used to identify and discuss future trends in the composition of generated waste over time. An analysis of the current waste management status in Greece as well as the feasibility of implementing a comprehensive management approach is assessed taking into account guidelines set worldwide to promote renewable energy sources use. It is concluded that recycling, perhaps the most positively received of all waste management practices, is going to be an essential part of contemporary waste management strategies, composting can play an important role, while incineration seems to be a conditionally feasible solution.     

Prediction of household and commercial BMW generation according to socio-economic and other factors for the Dublin region

Both planning and design of integrated municipal solid waste management systems require accurate prediction of waste generation. This research predicted the quantity and distribution of biodegradable municipal waste (BMW) generation within a diverse ‘landscape’ of residential areas, as well as from a variety of commercial establishments (restaurants, hotels, hospitals, etc.) in the Dublin (Ireland) region. Socio-economic variables, housing types, and the sizes and main activities of commercial establishments were hypothesized as the key determinants contributing to the spatial variability of BMW generation. A geographical information system (GIS) ‘model’ of BMW generation was created using ArcMap, a component of ArcGIS 9. Statistical data including socio-economic status and household size were mapped on an electoral district basis. Historical research and data from scientific literature were used to assign BMW generation rates to residential and commercial establishments. These predictions were combined to give overall BMW estimates for the region, which can aid waste planning and policy decisions. This technique will also aid the design of future waste management strategies, leading to policy and practice alterations as a function of demographic changes and development. The household prediction technique gave a more accurate overall estimate of household waste generation than did the social class technique. Both techniques produced estimates that differed from the reported local authority data; however, given that local authority reported figures for the region are below the national average, with some of the waste generated from apartment complexes being reported as commercial waste, predictions arising from this research are believed to be closer to actual waste generation than a comparison to reported data would suggest. By changing the input data, this estimation tool can be adapted for use in other locations. Although focusing on waste in the Dublin region, this method of waste prediction can have significant potential benefits if a universal method can be found to apply it effectively.     

Seasonal generation and composition of garden waste in Aarhus (Denmark)

Garden waste generation and composition were studied in Aarhus, Denmark. The amount of garden waste generated varied seasonally, from 2.5 kg person^?1 month^?1 in winter to 19.4 kg person^?1 month^?1 in summer. Seasonal fractional composition and chemical characterization of garden waste were determined by sorting and sampling garden waste eight times during 1 year. On a yearly basis, the major fraction of garden waste was “small stuff” (flowers, grass clippings, hedge cuttings and soil) making up more than 90% (wet waste distribution) during the summer. The woody fractions (branches, wood) are more significant during the winter. Seasonal trends in waste chemical composition were recorded and an average annual composition of garden waste was calculated, considering the varying monthly generation and material fraction composition: the wet garden waste contained 40% water, 30% organic matter (VS) and 30% ash. The ash content suggests that the garden waste contains a significant amount of soil. This is in particular the case during summer. Of nutrients, the garden waste contained in average on a dry matter basis 0.6% N, 0.1% P, and 1.0% K. However, the contents varied significantly among the fractions and during the year. The content of trace elements (Cd, Cr, Cu, Hg, Ni, Pb, and Zn) was low.     

Effects of pre-treatment technologies on quantity and quality of source-sorted municipal organic waste for biogas recovery

Source-sorted municipal organic waste collected from different dwelling types in five Danish cities and pre-treated at three different plants was sampled and characterized several times during one year to investigate the origin of any differences in composition of the pre-treated waste introduced by city, pre-treatment technology, dwelling type or annual season. The investigated pre-treatment technologies were screw press, disc screen and shredder+magnet. The average quantity of pre-treated organic waste (biomass) produced from the incoming waste varied between the investigated pre-treatment technologies: 59%, 66% and 98% wet weight, respectively (41%, 34% and 2% reject, respectively). The pre-treatment technologies showed differences with respect to distribution of the chemical components in the waste between the biomass and the rejected material (reject), especially for dry matter, ash, collection bag material (plastic or paper) and easily degradable organic matter. Furthermore, the particle size of the biomass was related to the pre-treatment technology. The content of plastic in the biomass depended both on the actual collection bag material used in the system and the pre-treatment technology. The sampled reject consisted mostly of organic matter. For cities using plastic bags for the source-separated organic waste, the expected content of plastic in the reject was up to 10% wet weight (in some cases up to 20%). Batch tests for methane potential of the biomass samples showed only minor variations caused by the factors city, pre-treatment technology, dwelling type and season when based on the VS content of the waste (overall average 459STPm(3)/tVS). The amount of methane generated from 1t of collected waste was therefore mainly determined by the efficiency of the chosen pre-treatment technology described by the mass distribution of the incoming waste between biomass and reject.     

ANALYSIS OF RESIDENTIAL SOLID WASTE AT GENERATION SITES

An essential preliminary step in municipal solid waste (MSW) management is the accurate determination of the quantities and composition of the wastes. The purpose of this study was to test a procedure for the determination of these parameters at the source of generation (houses), rather than getting such data at transfer stations or disposal sites, as usually done in most previous studies. The average generation rate in kg per capita day⁻¹and percentages of various components of residential solid waste in Abu Dhabi City were determined by carrying out a statistically designed sampling survey. This survey covered 40 houses with different socio-economic levels and totalled 840 samples. The study showed an average generation rate of 1.76 kg per capita day⁻¹. Linear regression analysis revealed that this rate was dependent on the income level with an increase of about 35% for the high income residents over the average rate. The waste contained approximately 50% food waste. Frequency distribution analysis of waste composition data indicated that the food waste component is normally distributed, whereas the other components do not show a normal distribution pattern.     

Sustainable recycling of municipal solid waste in developing countries

This research focuses on recycling in developing countries as one form of sustainable municipal solid waste management (MSWM). Twenty-three case studies provided municipal solid waste (MSW) generation and recovery rates and composition for compilation and assessment. The average MSW generation rate was 0.77 kg/person/day, with recovery rates from 5-40%. The waste streams of 19 of these case studies consisted of 0-70% recyclables and 17-80% organics. Qualitative analysis of all 23 case studies identified barriers or incentives to recycling, which resulted in the development of factors influencing recycling of MSW in developing countries. The factors are government policy, government finances, waste characterization, waste collection and segregation, household education, household economics, MSWM (municipal solid waste management) administration, MSWM personnel education, MSWM plan, local recycled-material market, technological and human resources, and land availability. Necessary and beneficial relationships drawn among these factors revealed the collaborative nature of sustainable MSWM. The functionality of the factor relationships greatly influenced the success of sustainable MSWM. A correlation existed between stakeholder involvement and the three dimensions of sustainability: environment, society, and economy. The only factors driven by all three dimensions (waste collection and segregation, MSWM plan, and local recycled-material market) were those requiring the greatest collaboration with other factors.     

Composition of source-sorted municipal organic waste collected in Danish cities

Source-sorted municipal organic waste from different dwelling types in five Danish cities was sampled during one year. The samples were from permanent, full-scale systems or temporary, experimental systems for collection of source-sorted municipal organic waste. Pre-treatment of the organic waste prior to biological treatment was used in all cities to remove foreign objects and provide size reduction. All sampling was performed after pre-treatment in order to obtain more homogeneous and representative samples. The sampling included both the pre-treated waste and the reject from the pre-treatment allowing for estimation of the composition of the original waste. A total of 40 waste samples were chemically characterised with respect to 15 parameters. The waste generally consisted of around 88% VS of which an average of 80% was easily degradable. The average content of N, P and K in the dry matter of the organic waste was 2.5%, 0.4% and 0.9%, respectively. A general analysis of variance was applied to show the influence of the collection system, dwelling type and annual season on the waste composition. The content of plastic and crude fibres in the waste differed the most among the samples, probably due to use of different bag types (plastic and paper) in the different collection systems. Variations in the ash content and the calorific value might be explained by differences in the sorting instructions (whether soil and cat litter are allowed in the organic fraction). Significant seasonal variations were seen for ash, S and Cl. Dwelling type showed no statistically significant influence on any waste components. A test for uniform distribution of the p-values from the analysis of variance (Kolmogorov-Smirnov test) showed that the overall composition of the collected waste was strongly affected by the collection system (city) and season, while dwelling type had no significant influence.     

Medical waste production at hospitals and associated factors

This study was conducted to evaluate the quantities of medical waste generated and the factors associated with the generation rate at medical establishments in Taiwan. Data on medical waste generation at 150 health care establishments were collected for analysis in 2003. General medical waste and infectious waste production at these establishments were examined statistically with the potential associated factors. These factors included the types of hospital and clinic, reimbursement payment by National Health Insurance, total number of beds, bed occupancy, number of infectious disease beds and outpatients per day. The average waste generation rates ranged from 2.41 to 3.26kg/bed/day for general medical wastes, and 0.19-0.88kg/bed/day for infectious wastes. The total average quantity of infectious wastes generated was the highest from medical centers, or 3.8 times higher than that from regional hospitals (267.8 vs. 70.3Tons/yr). The multivariate regression analysis was able to explain 92% of infectious wastes and 64% of general medical wastes, with the amount of insurance reimbursement and number of beds as significant prediction factors. This study suggests that large hospitals are the major source of medical waste in Taiwan. The fractions of medical waste treated as infectious at all levels of healthcare establishments are much greater than that recommended by the USCDC guidelines.