A numerical study of the auto-ignition temperatures of CH4–Air,C3H8–Air,CH4–C3H8–Air and CH4–CO2–Air mixtures

The auto-ignition temperature (AIT) is an important parameter in the process industries. In order to ensure a safe working environment in process industries, it is important to predict the AIT of combustible gases or vapors. In this study, the AITs of natural gas mixtures (CH₄–Air, C₃H₈–Air, CH₄–C₃H₈–Air and CH₄–CO₂–Air) are calculated based on a detailed kinetic model. To create a more practical model, different ignition criteria and convective heat transfer coefficients are investigated and compared against one another, resulting in the temperature criterion and a convective heat transfer coefficient of h = 50 W/(m² K). The results showed that the AITs of CH₄–Air and C₃H₈–Air decrease with an increase of equivalence ratios. While the propane ratio increasing, the AIT of CH₄–C₃H₈–Air decreasing. Reaction path analysis of natural gas mixtures (CH₄–C₃H₈) was also carried out to explain this phenomenon, yielding results showing that C₃H₈ is the main reaction during the ignition induction period. In addition the AIT of CH₄ increases slowly in positive correlation with CO_2, which plays a role of an inert gas. Comparing the results with literature work revealed a deviation of about 10%. Thus, it can be reasonably concluded that the AIT of a low hydrocarbons mixtures such as natural gas can be reliably predicted with detailed kinetic model.     

Venting of deflagrations: hydrocarbon–air and hydrogen–air systems

A set of 34 experiments on vented hydrocarbon–air and hydrogen–air deflagrations in unobstructed enclosures of volume up to 4000 m³ was processed with use of the advanced lumped parameter approach. Reasonable compliance between calculated pressure–time curves and experimental pressure traces is demonstrated for different explosion conditions, including high, moderate, low and extremely low reduced overpressures in enclosures of different shape (L_max:L_min up to 6:1) with different type and position of the ignition source relative to the vent, for near-stoichiometric air mixtures of acetone, methane, natural gas and propane, as well as for lean and stoichiometric hydrogen–air mixtures. New data were obtained on flame stretch for vented deflagrations.The fundamental Le Chatelier–Brown principle analog for vented deflagrations has been considered in detail and its universality has been confirmed. The importance of this principle for explosion safety engineering has been emphasized and proved by examples.A correlation for prediction of the deflagration–outflow interaction number, χ/μ, on enclosure scale, Bradley number and vent release pressure is suggested for unobstructed enclosures and a wide range of explosion conditions. Fractal theory has been employed to verify the universality of the dependence revealed of the deflagration–outflow interaction number on enclosure scale.In spite of differences between the thermodynamic and kinetic parameters of hydrocarbon–air and hydrogen–air systems, they both obey the same general regularities for vented deflagrations, including the Le Chatelier–Brown principle analog and the correlation for deflagration–outflow interaction number.     

Injury surveillance trends in career–technical education: New Jersey 1999–2018

Introduction: Adolescents engaging in school-sponsored work experiences may be at risk of injury due to factors such as inexperience. This article examines trends in 20 years of reported injuries among New Jersey (NJ) adolescents engaging in school-sponsored work experiences, and compares a transition from paper to online reporting format. Methods: New Jersey requires reporting of injuries occurring during school-sponsored work experiences to the NJ Department of Education. Injuries reported by NJ schools from 1999 to 2018 (n = 2,119) were examined; incidence rates for 2008 to 2018 (n = 743) were calculated using publicly available NJ Department of Education enrollment data for the denominator, including for specific groups of students: career and technical education; special healthcare needs. Results: A downward trend in reported injuries in NJ schools was observed. However, the year online reporting became required by code (2013), an increase of nearly 50% was seen from 2012 (59–89), followed by a decline in reported incidents 2014 to 2018 (mean = 65, range 76 down to 47). Injury rate trends over time paralleled those of reported incidents. Conclusions: This study suggested worker safety and public health benefits of improvements from State of NJ code required training programs and online injury surveillance report form. Practical Applications: One potential method to address the safety and health of adolescents engaging in work experiences is the use of online reporting forms, to aid in surveillance efforts, coupled with occupational safety and health training specifically geared toward teachers and administrators who both supervise young, relatively inexperienced and vulnerable workers and who make relatively frequent worksite visits. Incorporation of specific details of the instructions on the use of a reporting form into required trainings, in addition to providing a clear, accessible guidance manual online, could further help improve youth worker safety surveillance efforts.     

Experimental study on DDT for hydrogen–methane–air mixtures in tube with obstacles

An experimental study of flame propagation, acceleration and transition to detonation in stoichiometric hydrogen–methane–air mixtures in 6 m long tube filled with obstacles located at different configurations was performed. The initial conditions of the hydrogen–methane–air mixtures were 1 atm and 293 K. Four different cases of obstacle blockage ratio (BR) 0.7, 0.6, 0.5 and 0.4 and three cases of obstacle spacing were used. The wave propagation was monitored by piezoelectric pressure transducers PCB. Pressure transducers were located at different positions along the channel to collect data concerning DDT and detonation development. Tested mixtures were ignited by a weak electric spark at one end of the tube. Detonation cell sizes were measured using smoked foil technique and analyzed with Matlab image processing toolbox. As a result of the experiments the deflagration and detonation regimes and velocities of flame propagation in the obstructed tube were determined.     

Airbag deployment–related eye injuries

Objective: We studied the correlation between airbag deployment and eye injuries using 2 different data sets.

Methods: The registry of the Finnish Road Accident (FRA) Investigation Teams was analyzed to study severe head- and eyewear-related injuries. All fatal passenger car or van accidents that occurred during the years 2009–2012 (4 years) were included (n = 734). Cases in which the driver's front airbag was deployed were subjected to analysis (n = 409). To determine the proportion of minor, potentially airbag-related eye injuries, the results were compared to the data for all new eye injury patients (n = 1,151) recorded at the Emergency Clinic of the Helsinki University Eye Hospital (HUEH) during one year, from May 1, 2011, to April 30, 2012.

Results: In the FRA data set, the unbelted drivers showed a significantly higher risk of death (odds ratio [OR] = 5.89, 95% confidence interval [CI], 3.33–10.9, P = 2.6E-12) or of sustaining head injuries (OR = 2.50, 95% CI, 1.59–3.97, P = 3.8E-5). Only 4 of the 1,151 HUEH patients were involved in a passenger car accident. In one of the crashes, the airbag operated, and the belted driver received 2 sutured eye lid wounds and showed conjunctival sugillation. No permanent eye injuries were recorded during the follow-up. The calculated annual airbag-related eye injury incidence was less than 1/1,000,000 people, 4/100,000 accidents, and 4/10,000 injured occupants.

Conclusions: Airbag-related eye injuries occurred very rarely in car accidents in cases where the occupant survived and the restraint system was appropriately used. Spectacle use did not appear to increase the risk of eye injury in restrained occupants.     

Surveillance of traffic incident management–related occupational fatalities in Kentucky, 2005–2016

Objective: Traffic incidents occurring on roadways require the coordinated effort of multiple responder and recovery entities, including communications, law enforcement, fire and rescue, emergency medical services, hazardous materials, transportation agencies, and towing and recovery. The objectives of this study were to (1) identify and characterize transportation incident management (TIM)-related occupational fatalities; (2) assess concordance of surveillance data sources in identifying TIM occupations, driver vs. pedestrian status, and occupational fatality incident location; and (3) determine and compare U.S. occupational fatality rates for TIM industries.

Methods: The Kentucky Fatality Assessment and Control Evaluation (FACE) program analyzed 2005–2016 TIM occupational fatality data using multiple data sources: death certificate data, Collision Report Analysis for Safer Highways (CRASH) data, and media reports, among others. Literal text analysis was performed on FACE data, and a multiple linear regression model and SAS proc sgpanel were used to estimate and visualize the U.S. TIM occupational mortality trend lines and confidence bounds.

Results: There were 29 TIM fatalities from 2005 to 2015 in Kentucky; 41% of decedents were in the police protection occupation, and 21% each were in the fire protection and motor vehicle towing industries. Over one half of the TIM decedents were performing work activities as pedestrians when they died. Media reports identified the majority of the occupational fatalities as TIM related (28 of 29 TIM-related deaths); the use of death certificates as the sole surveillance data source only identified 17 of the 29 deaths as TIM related, and the use of CRASH data only identified 4 of the 29 deaths as TIM related. Injury scenario text analysis showed that law enforcement vehicle pursuit, towing and recovery vehicle loading, and disabled vehicle response were particular high-risk activities that led to TIM deaths. Using U.S. data, the motor vehicle towing industry had a significantly higher risk for occupational mortality compared to the fire protection and police protection industries.

Conclusions: Multiple data sources are needed to comprehensively identify TIM fatalities and to examine the circumstances surrounding TIM fatalities, because no one data source in itself was adequate and undercounted the total number of TIM fatalities. The motor vehicle towing industry, in particular, is at elevated risk for occupational mortality, and targeted mandatory TIM training for the motor vehicle towing industry should be considered. In addition, enhanced law enforcement roadside safety training during vehicle pursuit and apprehension of suspects is recommended.     

Effects of initial temperature and pressure on explosion characteristics of propane–diluent–air mixtures

The explosion characteristics of propane–diluent–air mixtures under various temperatures and pressures were investigated using a 20-L apparatus. The explosion limits of propane diluted with nitrogen or carbon dioxide were measured at high temperatures from 25 to 120 °C. The results showed that the upper explosion limit (UEL) increased, and the lower explosion limit (LEL) decreased with the rising temperature. The explosion limits of propane diluted with nitrogen or carbon dioxide were also measured at high pressures from 0.10 to 0.16 MPa. The results showed that the UEL increased, and the LEL almost remainedunchanged along with increased pressure. Under the same initial operating conditions, the concentration of nitrogen required to reach the minimum inerting concentration (MIC) point was higher than the concentration of carbon dioxide. Finally, the study investigated the limiting oxygen concentration (LOC) of propane under various initial temperatures, initial pressures, and inert gases. The LOC of propane decreased approximately linearly with increased temperature or pressure, and the LOC of propane dilution with carbon dioxide was greater than dilution with nitrogen from 25 to 120 °C or from 0.10 to 0.16 MPa, which indicated that the dilution effect of carbon dioxide was better than that of nitrogen.     

Spatial patterns of off-the-system traffic crashes in Miami–Dade County,Florida, during 2005–2010

Objective: The objective of this study is to analyze the spatial distribution of the vehicles involved in crashes in Miami–Dade County. In addition, we analyzed the role of time of day, day of the week, seasonality, drivers’ age in the distribution of traffic crashes.

Method: Off-the-system crash data acquired from the Florida Department of Transportation during 2005–2010 were divided into subcategories according to the risk factors age, time of day, day of the week, and travel season. Various spatial statistics methods, including nearest neighbor analysis, Getis-Ord hot spot analysis, and kernel density analysis revealed substantial spatial variations, depending on the subcategory in question.

Results: Downtown Miami and South Beach showed up consistently as hotspots of traffic crashes in all subcategories except fatal crashes. However, fatal crashes were concentrated in residential areas in inland areas.

Conclusion: This understanding of patterns can help the county target high-risk areas and help to reduce crash fatalities to create a safer environment for motorists and pedestrians.     

Impact of alkyl methacrylate–maleic anhydride–alkyl methacrylate terpolymers as cold flow improver on crystallization behavior of diesel fuel

Alkyl methacrylate–maleic anhydride–alkyl methacrylate terpolymers (MR₁–MA–MR₂) is one of the widely used cold flow improver. In order to develop more efficient MR₁–MA–MR₂, it is necessary to study the crystallization behavior of n-alkanes when adding MR₁–MA–MR₂ into diesel fuel. In this paper, MR₁–MA–MR₂ is prepared by the reaction of long-chain alkyl methacrylate (MR₁), maleic anhydride (MA), and short alkyl methacrylate (MR₂). The diesel fuel before and after adding MR₁–MA–MR₂ is in situ filtrated at its cold filter plugging point (CFPP) in a manual CFPP apparatus. Extensive measurements of composition variation of n-alkanes are done by gas chromatograph and the results are compared. The experimental results show that after adding MR₁–MA–MR₂, the concentration distribution of n-alkanes in the filtrate is wide and arranges from 8 to 26, and mainly centralizes from 10 to 19. For the precipitate, the concentration distribution of n-alkanes gets richer in the lighter n-alkanes and poorer in the heavier n-alkanes. The concentration distribution of n-alkanes in the crystal solid shows a decreasing trend, especially with high carbon number n-alkanes (heavier than C₂₀). About 60–70% of the residual crystal solid is composed of non-paraffins such as isoparaffin, naphthene and other components. Crystallinities of n-alkanes show a slow decrease trend from C₈ to C₂₀. When the carbon number n-alkanes are heavier than C₂₀, the crystallinities of n-alkanes begin to sharply reduce with an increase of carbon number. The largest decline of crystallinity is C₂₆ n-alkane from 38.39% to 7.90%.     

Explosion of lycopodium-nicotinic acid–methane complex hybrid mixtures

With the terms “complex hybrid mixtures”, we mean mixtures made of two or more combustible dusts mixed with flammable gas or vapors in air (or another comburent).In this work, the flammability and explosion behavior of selected complex hybrid mixtures was studied. In particular, we investigated mixtures of nicotinic acid, lycopodium and methane. We performed explosion tests in the 20-L explosion vessel at different overall (nicotinic plus lycopodium) dust concentrations, nicotinic acid/lycopodium ratios, and methane concentrations.An exceptional behavior (in terms of unexpected values of rate of pressure rise and pressure) was found for the complex hybrid mixtures containing lycopodium and nicotinic acid in equal amounts. This mixture was found to be much more reactive than all the other dust mixtures, whatever the dust concentration and the methane content.     

Traumatic brain injury mortality among U.S. children and adolescents ages 0–19 years, 1999–2017

IntroductionTo examine recent traumatic brain injury (TBI) mortality changes among Americans aged 0–19 years by sex, age, urbanicity, state, and intent/causes of injury. Method: TBI mortality per 100,000 population and average annual percent changes (AAPCs), plus 95% confidence intervals (CIs) based on Joinpoint regression models. Results: Age-adjusted TBI mortality among Americans aged 0–19 years declined consistently, though at varying rates between 1999 and 2013 (AAPC = −4.8%, 95%CI: −6.3%, −3.2%), and then significantly increased from 4.42 per 100,000 population in 2013 to 5.17 per 100,000 population in 2017 (AAPC = 3.4%, 95% CI: 1.7%, 5.1%). During the study time period, boys, rural children, and youth aged 15–19 years had higher TBI mortality rates than girls, urban children, and younger children, respectively. TBI mortality from unintentional transport crashes decreased substantially in all age groups between 1999 and 2017, and especially from 1999 to 2010. TBI mortality from suicide increased significantly from 2008 to 2017 in the 10–14-year age group (AAPC = 14.6%, 95% CI: 12.6%, 16.6%) and from 2007 to 2017 in the 15–19-year age group (AAPC = 6.3%, 95% CI: 3.8%, 8.7%). Unintentional transport crashes were the leading cause of TBI-related mortality in 46 states in 1999, but by 2017, suicide became the first leading cause in 14 states. Conclusions: Pediatric TBI mortality declined consistently between 1999 and 2013 and increased significantly from 2013 to 2017, driven primarily by the mortality decrease from unintentional transport crashes and increase in suicide mortality. The spectrum of leading causes of pediatric TBI mortality changed across age groups and over time from 1999 to 2017. Practical Applications: TBI mortality increases in the United States since 2013 are driven primarily by increasing suicide rates, a trend that merits the attention of policy-makers and injury researchers. Action should be taken to curb growing TBI mortality rates among adolescents aged 10–19 years.     

Methane–air detonation experiments at NIOSH Lake Lynn Laboratory

The methane–air detonation experiments are performed to characterize high pressure explosion processes that may occur in sealed areas of underground coal mines. The detonation tube used for these studies is 73 m long, 105 cm internal diameter, and closed at one end. The test gas is 97.5% methane with about 1.5% ethane, and the methane–air test mixtures varied between 4% and 19% methane by volume. Detonations were successfully initiated for mixtures containing between 5.3% and 15.5% methane. The detonations propagated with an average velocity between 1512 and 1863 m/s. Average overpressures recorded behind the first shock pressure peak varied between 1.2 and 1.7 MPa. The measured detonation velocities and pressures are close to their corresponding theoretical Chapman-Jouguet (CJ) detonation velocity (D_CJ) and detonation pressure (P_CJ). Outside of these detonability limits, failed detonations produced decaying detached shocks and flames propagating with velocities of approximately 1/2 D_CJ. Cell patterns on smokefoils during detonations were very irregular and showed secondary cell structures inside primary cells. The measured width of primary cells varied between 20 cm near the stoichiometry and 105 cm (tube diameter) near the limits. The largest detonation cell (105 cm wide and 170 cm long) was recorded for the mixture containing 15.3% methane.     

Predicting vehicle belt fit for children ages 6–12

Objective: To predict shoulder belt fit and lap belt fit as a function of child age, vehicle seat characteristics, and belt geometry.

Methods: In a previous study, the lap belt and shoulder belt fit of 44 children aged 5–12 were measured in a simulated vehicle seat while varying cushion length, cushion angle, seatback angle, and belt anchorage geometry. A regression model was developed to predict lap belt fit and shoulder belt fit as a function of vehicle parameters and child stature. These regression models were applied to the stature distribution of 6- to 12-year-olds using a range of vehicle geometry data to predict the proportion of children expected to achieve good belt fit in the second-row, outboard seating positions of 46 vehicles when not using belt-positioning boosters.

Results: Across the ranges observed in vehicles, lap belt angle had the strongest effect on lap belt fit, although vehicle cushion length also contributed. Shoulder belt fit was most strongly affected by D-ring location. Vehicles with the geometric conditions most suitable for children are estimated to provide good lap belt fit for 25% of children aged 6 to 12. In 20% of vehicles, the shoulder belt is too far inboard for the target child population; 20% of vehicles are estimated to have shoulder belt fit too far outboard for children ages 6 to 12.

Conclusions: Based on this geometric analysis, the rear seats of most vehicles are unlikely to provide good lap belt fit for up to 75% of children ages 6–12. Shoulder belt fit is outside the target range for 40% of children. Consequently, children under 12 years of age are likely to experience markedly poorer belt fit when transitioning out of a booster seat.     

Occupational accidents model based on risk–injury affinity groups

This article sets outs a generalized utility model for the diagnosis and prediction of accidents among the Spanish workforce. Based on observational data classified into a risk–injury contingency table (19 × 19), we have summarized the accident rate of all Spanish companies over an 11-year period (75,19,732 accidents). By using correspondence analysis a structure composed of three axes can be obtained, the combination of which identifies three separate risk and injury groups, which we use as a general Spanish pattern. The relationships of greater affinity or likelihood amongst the risks and injuries identified in the pattern facilitate decision-making at the risk-assessment stage in Spanish companies. Each risk–injury group has its own characteristics, interpretable within the phenomenological framework of the accident.The main advantage of this model is its potential application to any other country and the feasibility of contrasting results from different countries. One limiting factor, however, is that the model currently lacks a common classification frame for risks and injuries which would enhance this contrast. The aim of this model is to automatically manage work-related accidents at a national level.     

Degradation of Rhodamine B by an electrochemical ozone generating system consist of a Ti anode coated with nanocomposite of Sn–Sb–Ni oxide

An ozonation process was performed using a recycled electrochemical ozone generator system. A titanium based electrode, coated with nanocomposite of Sn–Sb–Ni was applied as anode in a laboratory-made electrochemical reactor. A constant flow rate of 192 mg/h of generated ozone was entered to an ozonation reactor to contact with a typical target pollutant, i.e., Rhodamine B (Rh.B) molecules in aqueous solution. Four operational parameters such as: initial dye concentration, pH, temperature and the contact time were evaluated for the ozonation process. Experimental findings revealed that for a solution of 8 mg/L of the dye, the degradation efficiency could reach to 99.5% after 30 min at pH 3.7 and temperature of 45 °C as the optimum conditions. Kinetic studies showed that a second order equation can describe the ozonation adequately well under different temperatures. Also, considering to the importance of process simulation, a three-layered feed forward back propagation artificial neural network model was developed. Sensitivity analysis indicated order of the operational parameter's relative importance on the model output as: time ≫ pH > Rh . B initial concentration > temperature.     

Effects of cross-wise obstacle position on methane–air deflagration characteristics

A vented chamber, with internal dimensions of 150 mm × 150 mm × 500 mm, is constructed in which the premixed methane–air deflagration flame, propagating away from the ignition source, interacts with obstacles along its path. Three obstacle configurations with different cross-wise positions are investigated. The cross-wise obstacle positions are found to have significant effects on deflagration characteristics, such as flame structure, flame front location, flame speed, and overpressure transients. The rate of flame acceleration, as the flame passes over the last obstacle, is the highest at the configuration with three centrally located obstacles, whereas the lowest is observed at the configuration with three obstacles mounted on one side of the chamber. Compared with the side configuration, the magnitude of overpressure generated increases by approximately 80% and 165% for the central and staggered configurations, respectively. Furthermore, flame propagation speeds and generated overpressures for both the central and staggered configurations are greater, which should to be avoided to reduce the risk associated with turbulent premixed deflagrations in practical processes.