在Pt/Al2O3催化剂上异丁醇完全氧化动力学

在Pt/Al_2O_3催化剂上用外循环无梯度反应器研究了异丁醇完全氧化动力学,异丁醇完全氧化动力学方程用异丁醇及氧吸附,CO_2吸附阻碍的L-H模型描述,用正交设计法求出动力学方程中的参数,用脉冲法测定了异丁醇、氧及CO_2的吸附热。     

Steady-state kinetics and osillation phenomena for complete oxidation of benzene over Pt/Al_2O_3 catalyst

The steady-state kinetics for complete oxidation of benzene over has been investigated by the external recycling reactor. The kinetics equation was described by the L-H model of adsorption of benzene and oxygen with the inhibition of carbon dioxide. The parameters of the kinetics model were estimated by the method of orthogonal design. The heats of adsorption of benzene, oxygen and carbon dioxide were determined by the method of gas-adsorption chromatography. The details of oscillations of complete oxidation of benzene were investigated.     

La-EDTA coated Fe3O4 nanomaterial: Preparation and application in removal of phosphate from water

La-EDTA-Fe3O4 was prepared by a chemical co-precipitation method. The magnetic composite was characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). Furthermore, the adsorption properties of La-EDTA-Fe3O4 toward phosphate in water were investigated. The uptake rate of phosphate in water by La-EDTA-Fe3O4 was 3-1000 times than that of EDTA-Fe3O4 , and reached 97.8% at 7 hr. The adsorption process agreed well with the Freundlich model and kinetics studies showed that the adsorption of phosphate proceeds according to pseudo second-order adsorption kinetics. The maximum removal rate was achieved at pH 6.0-7.0. The La-EDTA-Fe3O4 had good adsorption properties and could be separated well from aqueous solution by a permanent magnet. Therefore, this nanomaterial has potential application for the removal of phosphate from large water bodies.     

Ti/Ti4O7阳极电化学氧化降解水中的美托洛尔

等离子喷涂法制备了钛基亚氧化钛电极(Ti/Ti_4O_7),以该电极为阳极,研究了电化学氧化法对水中美托洛尔的去除效果.考察了电流密度(5~25 mA·cm~(-2))、极板间距(5~25 mm)和初始浓度(3~50 mg·L~(-1))对美托洛尔电化学降解效率的影响;分析美托洛尔电化学降解过程中溶液总有机碳(TOC)和毒性的变化,鉴别反应中间产物并计算其毒性.研究表明:Ti/Ti_4O_7阳极电化学降解美托洛尔反应符合一级反应动力学规律(R20.95),降解效率随电流密度的增大而增大,随极板间距和初始浓度的增大而减小;TOC去除率在反应40 min后可达56.5%;反应过程中产生了质合比为266、250、223和207的中间产物,造成美托洛尔溶液的生物毒性在电化学反应过程中先升高后下降.     

Effect of TiO2 calcination temperature on the photocatalytic oxidation of gaseous NH3

Carbon-modified titanium dioxide(TiO2) was prepared by a sol-gel method using tetrabutyl titanate as precursor, with calcination at various temperatures, and tested for the photocatalytic oxidation(PCO) of gaseous NH3 under visible and UV light. The test results showed that no samples had visible light activity, while the TiO2 calcined at 400℃ had the best UV light activity among the series of catalysts, and was even much better than the commercial catalyst P25. The catalysts were then characterized by X-ray diffractometry, Brunauer-Emmett-Teller adsorption analysis, Raman spectroscopy, thermogravimetry/differential scanning calorimetry coupled with mass spectrometry, ultraviolet-visible diffuse reflectance spectra, photoluminescence spectroscopy and in situ diffuse reflectance infrared Fourier transform spectroscopy. It was shown that the carbon species residuals on the catalyst surfaces induced the visible light adsorption of the samples calcined in the low temperature range( 300℃). However, the surface acid sites played a determining role in the PCO of NH3 under visible and UV light over the series of catalysts. Although the samples calcined at low temperatures had very high SSA, good crystallinity, strong visible light absorption and also low PL emission intensity, they showed very low PCO activity due to their very low number of acid sites for NH3 adsorption and activation. The TiO2 sample calcined at 400℃ contained the highest number of acid sites among the series of catalysts, therefore showing the highest performance for the PCO of NH3 under UV light.     

Catalytic oxidation of benzene over nanostructured porous Co3O4-CeO2 composite catalysts

The three-dimensional structured Co₃O₄-CeO₂ oxides with Co/Ce molar ratio 16:1 gave the highest catalytic activity, which provided more surface hydroxyl groups and more surface oxygenated species.     

在Pt/Al2O3催化剂上甲醇深度氧化的稳态及非稳态动力学

用玻璃外循环无梯度反应器研究了在Pt/Al_2O_3催化剂上甲醇深度氧化稳态动力学,甲醇深度氧化稳态动力学服从L-H机理模型。用正交设计法估计了动力学方程中的参数。用脉冲法测定了甲醇、氧及CO_2的吸附热。用脉冲法研究了甲醇在催化剂上吸附量与停留时间的关系,实验中观察到在Pt/Al_2O_3催化剂上甲醇深度氧化的振荡现象。     

草甘膦在高指{201}二氧化钛表面的吸附去除

有机磷农药草甘膦(PMG)的广泛使用和环境残留严重威胁人体健康,其去除治理是环境领域面临的一大挑战.本文研究了草甘膦在高指{201}晶面二氧化钛(TiO_2)上的吸附行为,探讨了吸附时间、溶液pH和草甘膦浓度对吸附效率的影响,并通过Zeta电位表征和电荷分布多位点络合(CD-MUSIC)模型考察了草甘膦在二氧化钛上的络合结构.结果表明,{201}TiO_2对草甘膦的吸附在40 min内即可达到吸附平衡,吸附动力学符合准二级动力学方程.吸附等温线符合Langmuir方程,说明其吸附过程主要是近似单分子层的化学吸附.pH对吸附效率影响较大,酸性条件有利于草甘膦的吸附去除.Zeta电位的表征结果表明,草甘膦吸附后TiO_2表面等电点从5.6向左偏移至4.2,说明形成带负电的内层配合物,进一步的红外光谱结果表明草甘膦以P—O—Ti的络合形式与TiO_2表面结合.CD-MUSIC模型拟合结果表明草甘膦与TiO_2表面可能形成单齿单核或双齿双核的内层络合结构.本研究结果对深入理解草甘膦的微观界面行为及去除具有重要意义.     

磁性核壳CoFe2O4@SiO2@PIL-AO复合材料的制备及其吸附U (VI)性能研究

通过化学合成法制备了磁性核壳CoFe₂O₄@SiO₂@PIL-AO复合材料,采用傅立叶变换红外光谱（FTIR）、扫描电镜（SEM）和X射线光电子能谱（XPS）对其进行了表征,研究了溶液pH、吸附时间、U （VI）初始浓度和温度等参数对U （VI）吸附性能的影响.实验结果表明：在c₀=0.2 mg·L^-1、pH=6.00±0.05、T=298.15 K、m=0.02 g和t=8 h的条件下,CoFe₂O₄@SiO₂@PIL-AO对U （VI）的吸附作用最强,吸附率达到了97.54%;CoFe₂O₄@SiO₂@PIL-AO吸附U （VI）是一个自发进行的吸热反应,U （VI）吸附动力学符合准二级动力学模型,吸附等温线符合Freundlich模型;CoFe₂O₄@SiO₂@PIL-AO复合材料具有良好的可循环使用性,循环使用5次后它对U （VI）的吸附容量没有明显下降,可重复使用.     

磷酸水热预处理制备高比表面积高介孔率活性炭

以锯末为原材料,采用磷酸水热预处理后活化的工艺制备高介孔率活性炭,以比表面积和孔容为评价标准,通过单因素实验探究了酸料比、活化温度、活化时间对活性炭比表面积及总孔容的影响规律,验证了该工艺的可行性.最优条件下所制备的活性炭比表面积为2579 m~2·g~(-1),介孔率达到96.6%,充分说明磷酸水热预处理工艺能够显著提高活性炭介孔孔容占比.亚甲基蓝(MB)吸附实验数据与Redlich-Peterson模型拟合度较好,样本活性炭对MB的吸附为单分子层吸附,最大单层吸附量为618.35 mg·g~(-1),接近于实验测试值632.79 mg·g~(-1),表明该方法制备的活性炭具有良好的MB吸附性能.     

CO2 adsorption using TiO2 composite polymeric membranes: A kinetic study

CO₂ is the main greenhouse gas which causes global climatic changes on larger scale. Many techniques have been utilised to capture CO₂. Membrane gas separation is a fast growing CO₂ capture technique, particularly gas separation by composite membranes. The separation of CO₂ by a membrane is not just a process to physically sieve out of CO₂ through the controlled membrane pore size. It mainly depends upon diffusion and solubility of gases, particularly for composite dense membranes. The blended components in composite membranes have a high capability to adsorb CO₂. The adsorption kinetics of the gases may directly affect diffusion and solubility. In this study, we have investigated the adsorption behaviour of CO₂ in pure and composite membranes to explore the complete understanding of diffusion and solubility of CO₂ through membranes. Pure cellulose acetate (CA) and cellulose acetate-titania nanoparticle (CA-TiO₂) composite membranes were fabricated and characterised using SEM and FTIR analysis. The results indicated that the blended CA-TiO₂ membrane adsorbed more quantity of CO₂ gas as compared to pure CA membrane. The high CO₂ adsorption capacity may enhance the diffusion and solubility of CO₂ in the CA-TiO₂ composite membrane, which results in a better CO₂ separation. The experimental data was modelled by Pseudo first-order, pseudo second order and intra particle diffusion models. According to correlation factor R², the Pseudo second order model was fitted well with experimental data. The intra particle diffusion model revealed that adsorption in dense membranes was not solely consisting of intra particle diffusion.     

Co-adsorption of gaseous benzene, toluene, ethylbenzene, m-xylene (BTEX) and SO2 on recyclable Fe3O4 nanoparticles at 0-101% relative humidities

We herein used Fe3O4 nanoparticles(NPs) as an adsorption interface for the concurrent removal of gaseous benzene, toluene, ethylbenzene and m-xylene(BTEX) and sulfur dioxide(SO2), at different relative humidities(RH). X-ray diffraction, Brunauer–Emmett–Teller, and transmission electron microscopy were deployed for nanoparticle surface characterization.Mono-dispersed Fe3O4(Fe2O3·Fe O) NPs synthesized with oleic acid(OA) as surfactant, and uncoated poly-dispersed Fe3O4 NPs demonstrated comparable removal efficiencies.Adsorption experiments of BTEX on NPs were measured using gas chromatography equipped with flame ionization detection, which indicated high removal efficiencies(up to(95 ± 2)%) under dry conditions. The humidity effect and competitive adsorption were investigated using toluene as a model compound. It was observed that the removal efficiencies decreased as a function of the increase in RH, yet, under our experimental conditions, we observed(40 ± 4)% toluene removal at supersaturation for Fe3O4 NPs, and toluene removal of(83 ± 4)% to(59 ± 6)%, for OA-Fe3O4 NPs. In the presence of SO2, the toluene uptake was reduced under dry conditions to(89 ± 2)% and(75 ± 1)% for the uncoated and coated NPs, respectively, depicting competitive adsorption. At RH 100%,competitive adsorption reduced the removal efficiency to(27 ± 1)% for uncoated NPs whereas OA-Fe3O4 NPs exhibited moderate efficiency loss of(55 ± 2)% at supersaturation.Results point to heterogeneous water coverage on the NP surface. The magnetic property of magnetite facilitated the recovery of both types of NPs, without the loss in efficiency when recycled and reused.     

TiO2/Ag modified penta-bismuth hepta-oxide nitrate and its adsorption performance for azo dye removal

A modified hydrophilic penta-bismuth hepta-oxide nitrate (Bi₅O₇NO₃) surface was synthesized via a precipitation method using TiO₂ and Ag as modified agents. The synthesized product was characterized by different analytical techniques. The removal efficiency was evaluated using mono-and di-sulphonated azo dyes as model pollutants. Different kinetic, isotherm and diffusion models were chosen to describe the adsorption process. X-ray photoelectron spectroscopy (XPS) results revealed no noticeable differences in the chemical states of modified adsorbent when compared to pure Bi₅O₇NO₃;however, the presence of hydrophilic centres such as TiO₂ and Ag developed positively charged surface groups and improved its adsorption performance to a wide range of azo dyes. Dyes removal was found to be a function of adsorbent dosage, initial dye concentration, solution pH and temperature. The reduction of Langmuir 1,2-mixed order kinetics to the second or first-order kinetics could be successfully used to describe the adsorption of dyes onto the modified adsorbent. Mass transfer can be described by intra-particle diffusion at a certain stage, but it was not the rate limiting step that controlled the adsorption process. Homogenous behavior of adsorbent surface can be explored by applying Langmuir isotherm to fit the adsorption data.     

四氧化三铁/聚乙烯亚胺纳米颗粒的制备及除磷性能的研究

采用化学共沉淀法,以聚乙烯亚胺(PEI)为改性剂,制备了聚乙烯亚胺改性的纳米四氧化三铁复合材料(Fe3O4/PEI).Zeta电位、透射电镜和FTIR表征结果显示,PEI修饰提高了纳米Fe3O4在水中的分散性和稳定性,同时也增强了其表面正电荷,从而提高了Fe3O4对水中磷酸根的去除能力.在磷酸根初始浓度为50 mg·L~(-1),Fe3O4/PEI投加量为200 mg,p H=3,温度为25℃的条件下,Fe3O4/PEI对100 m L磷酸根的吸附去除率达到91%.吸附过程在3 h内达到平衡.吸附等温数据表明,该吸附过程符合Langmuir吸附等温方程,可决系数R2达到0.99,最大吸附量为29.88 mg·L~(-1).Fe3O4/PEI复合材料重复利用性好,在第5次吸附-解析后还能保持对磷酸根75%以上的吸附去除率.磷的解析效率随着p H增加而增加,在p H=13时,解析效率达到65%.     

纳米Fe3O4/CeO2-H2O2非均相类Fenton体系对3,4-二氯三氟甲苯的降解

以浸渍法制备的新型纳米Fe3O4/Ce O2为催化剂,3,4-二氯三氟甲苯(3,4-DCBTE)为目标污染物,在Fe3O4/Ce O2-H2O2非均相类Fenton体系中对目标污染物的降解进行研究,考察催化剂的催化效果和温度、p H、H2O2投加量等因素对催化剂催化效果的影响.结果表明,以纳米Fe3O4/Ce O2作为催化剂的非均相类Fenton体系对3,4-二氯三氟甲苯的处理效果极佳;随着温度的升高,纳米Fe3O4/Ce O2的催化效果不断提高;在偏酸性环境中,p H越低催化效果越好,p H=2时反应去除效率可达96.67%;随着H2O2投加量的增加,3,4-二氯三氟甲苯的降解效率先提高后降低,投加量为15 mg·L-1时去除效果最好可达99.47%;随着催化剂投加量的增加,同样出现了处理效果先升高后降低的现象,投加量为0.5 g·L-1时催化效果最好可达99.64%.在以纳米Fe3O4/Ce O2为催化剂的非均相类Fenton体系中,3,4-二氯三氟甲苯的降解符合一级反应动力学,反应所需活化能较低只需30.26 k J·mol-1.     

支化聚乙烯亚胺功能化磁性纳米吸附剂的制备及对Cu2+的吸附研究

为解决水体中重金属Cu²⁺污染,本研究首先采用水热法制备得到超顺磁四氧化三铁纳米粒子,然后使用对Cu²⁺具有强络合作用的含有丰富氨基官能团的支化聚乙烯亚胺接枝到纳米粒子表面,得到Fe₃O₄@BPEI磁性纳米吸附剂。采用红外光谱（FTIR）、X射线粉末衍射（XRD）、透射电子显微镜（TEM）等对其结构、尺寸及形貌进行表征。研究了不同吸附因素对吸附剂吸附Cu²⁺的影响,确定了最佳吸附条件,并通过吸附动力学模型和吸附等温线模型进一步探讨吸附机理。结果表明：支化聚乙烯亚胺成功接枝到四氧化三铁纳米粒子表面。最佳吸附条件为pH=6.0、吸附平衡时间为40 min、吸附剂用量为10 mg。通过实验数据拟合,Fe₃O₄@PEI吸附Cu²⁺的过程符合Langmuir等温吸附方程和拟二级动力学模型,表明吸附过程为化学吸附控制的单分子层覆盖,在303 K时,模型理论饱和吸附量为141.24 mg/g。表明支化聚乙烯亚胺修饰的磁性纳米吸附剂对Cu²⁺具有较强的吸附能力,对水体中Cu²⁺的去除具有一定的应用前景。     

淀粉稳定Fe3O4纳米粒子对水中As(V)的吸附特性研究

以可溶性淀粉作为稳定剂制备纳米Fe_3O_4粒子,探讨了反应时间、p H值、初始砷浓度和腐殖酸对Fe_3O_4纳米粒子吸附水体中As(V)的吸附效果影响.实验结果表明,淀粉稳定的Fe_3O_4纳米粒子对水体中As(V)的吸附动力学过程符合准二级动力学,吸附等温线符合Langmuir吸附模型;吸附容量随着溶液p H的增加逐渐降低,在p H为8.0的弱碱性水体中对As(V)的最大吸附容量可达202.56 mg·g~(-1);此外,腐殖酸(HA)能降低纳米粒子对As(V)的吸附能力.     

TiO2光催化氧化苯酚动力学研究

以中压汞灯为光源,研究了苯酚在ＴｉＯ２水悬浮液中降解动力学,考察了苯酚在起始浓度,气相氧浓度,催化剂投加量（ＴｉＯ２）光强度以及催化剂煅烧温度对苯酚光解速率的影响,揭示了苯酚多相光催化氧化反应的特点,反应过程符合表现一级动力学规律,气相氧的影响为一级,苯酚初始浓度的影响为负一级,在一定光强度下,催化剂的投加量存在一最值值,说明有效光强度,气相氧以及催化剂投加量是光催化氧化反应的关键因素,适当地热处     

氧掺杂g-C3N4光催化降解Cu-EDTA络合物的反应机理研究

本研究以Cu-EDTA为模拟污染物,探讨了非金属石墨相氮化碳(g-C_3N_4)在光催化降解重金属络合污染物中的应用潜力.首先采用在空气气氛下煅烧的方式对g-C_3N_4进行氧掺杂改性,并通过XRD、TEM和DRS等表征手段对掺杂前后的催化剂结构进行表征.光催化性能评价结果表明,氧掺杂改性更有利于催化剂表面光生空穴的分离,从而呈现出显著提升的破络合能力.通过自由基猝灭实验对g-C_3N_4光降解Cu-EDTA的催化机制进行了研究,结果表明,未掺杂g-C_3N_4通过O_2~(·-)、空穴和·OH的共同作用实现重金属络合物的去除,而氧掺杂样品以具有更强破络合能力的光生空穴为主要活性物种实现Cu-EDTA污染物的降解.     

Effect of Ce doping of TiO2 support on NH3-SCR activity over V2O5-WO3/CeO2-TiO2 catalyst

CeO2–TiO2composite supports with different Ce/Ti molar ratios were prepared by a homogeneous precipitation method, and V2O5–WO3/CeO2–TiO2catalysts for the selective catalytic reduction（SCR） of NOx with NH3 were prepared by an incipient-wetness impregnation method. These catalysts were characterized by means of BET, XRD, UV–Vis,Raman and XPS techniques. The results showed that the catalytic activity of V2O5–WO3/TiO2 was greatly enhanced by Ce doping（molar ratio of Ce/Ti = 1/10） in the TiO2 support.The catalysts that were predominantly anatase TiO2 showed better catalytic performance than the catalysts that were predominantly fluorite CeO2. The Ce additive could enhance the surface adsorbed oxygen and accelerate the SCR reaction. The effects of O2 concentration, ratio of NH3/NO, space velocity and SO2 on the catalytic activity were also investigated. The presence of oxygen played an important role in NO reduction. The optimal ratio of NH3/NO was 1/1 and the catalyst had good resistance to SO2 poisoning.