Application of TLC for confirmation and screening of pesticide residues in fruits, vegetables, and cereal grains: Part 2. Repeatability and reproducibility of Rf and MDQ values

This paper illustrates the effect of major factors influencing the reproducibility of thin layer chromatography (TLC) separation and detection under largely differing environmental and laboratory conditions. The optimum conditions for reproducibility and detection sensitivity was obtained on 20 x 20 cm layer in the retention factor (Rf) range of 0.2-0.7 by applying the sample in spots of 3-4 mm diameter at 2 cm from the edge of the plate. The reproducibility rapidly decreased below Rf = 0.2. Above Rf = 0.2 the within-laboratory reproducibility of 219 pesticides obtained in ethyl acetate silica gel elution system by several laboratories was typically below 10%. The among-laboratories reproducibility of the average retention factors was generally below 12%. The minimum detectable quantities (MDQ) of 219 pesticide residues were determined with nine detection methods. The MDQ values largely varied depending on the mode of detection. Bioassay methods enabled the detection down to 0.1-10 ng, while 20-100 ng could be achieved with the chemical reagents. Higher MDQ values are also reported in order to assist the identification of compounds potentially present. The between-laboratories reproducibility of MDQ values was typically 1-5 MDQmin.     

Multiresidue screening methods for the determination of pesticides in tomatoes

The possibility of applying thin layer chromatography (TLC) detection for the analysis of pesticide residues in tomatoes was investigated. Samples of tomatoes that have never been treated with pesticide were fortified with atrazine, carbaryl, carbofuran, chloroxuron, diuron, dimethoate, imazalil, oxamyl and methamidophos. The samples were extracted, cleaned-up by gel permeation chromatography and then applied on silica gel plates. The pesticides were eluted with ethyl acetate and dichloromethane. Two eluting solvent systems were tested, one using the reagents o-toluidine + potassium iodite (o-TKI) and the other p- nitrobenzene fluoroborate (NBFB). After the development of the plates, the diameter of the spots was measured. The lowest minimum detection quantity (MDQ) for o-TKI system for atrazine was 12 ng. The highest was 125 ng for carbofuran. Using NBFB system, the lowest MDQ was 60 ng for carbaryl and the highest was 70 ng obtained for carbofuran. Considering the concentration of these pesticides in the spiked tomato samples, the minimum concentration was 1.1 ng/microL and 32.3 ng/microL for atrazine and carbofuran, respectively, by using o-TKI system. For NBFB system the minimum concentration reached was 3.5 ng/microL and 4.3 ng/microL for carbaryl and carbofuran, respectively. This study showed that TLC can be used for semi-quantitative analysis.     

Validation of an efficient method for the determination of pesticide residues in fruits and vegetables using ethyl acetate for extraction

In this study, a version of the "quick, easy, cheap, effective, rugged, and safe" (QuEChERS) method was modified to use ethyl acetate (EtOAc) rather than acetonitrile (MeCN) for extraction in the determination of multiple pesticide residues in fruits and vegetables. EtOAc is better suited than MeCN for gas chromatographic (GC) analysis with electron capture detection (ECD) and nitrogen-phosphorus detection (NPD). The method entailed extraction of 30 g chopped sample plus 5 g NaHCO(3) and 30 g anhydrous Na(2)SO(4) with 60 mL EtOAc using a probe blender. After a centrifugation step, removal of residual water and cleanup were performed using dispersive solid-phase extraction (dispersive-SPE) with MgSO(4) and primary secondary amine (PSA) sorbent. (14)C-labeled chlorpyrifos with liquid scintillation counting was used to assist in optimizing and characterizing the method, and GC-ECD and GC-NPD were used for analysis of 24 selected pesticides. The method was validated using tomato, apple and frozen green bean matrices spiked at 0.05, 0.5, and 5 mg/kg. For 22 of the analytes, recoveries averaged 93% for all three commodities over the validation range with a relative standard deviation of 10% (n = 1182). Lower recoveries of dichlorvos were obtained with the method and iprodione determination was compromised in the green beans by an interfering peak. Typical limits of detection were 0.005-0.01 mg/kg with the method.     

A method for the analysis of organophosphorus pesticide residues in Mexican axolotl

A method based on matrix solid-phase dispersion (MSPD) was developed for quantitative extraction of three organophosphorus pesticides (OPPs) from the Mexican axolotl, Ambystoma mexicanum. The determination was carried out using high- performance liquid chromatography (HPLC) with diode array spectrophotometric UV detection (DAD). The MSPD extraction with octadecylsilyl (C18) sorbent combined with a silica gel clean-up and acetonitrile elution was optimised for chlorpyrifos, fenthion and methyl parathion. The method was validated, yielding recovery values higher than 90%. The precision, expressed as the relative standard deviation (RSD), was less than or equal to 6% in muscle samples at spiking levels of 10 and 5 ppm. Linearity was studied from 15 to 60 ppm for chlorpyrifos and fenthion, and from 7.5 to 30 ppm for methyl parathion. The limits of detection (LODs) were found to be less than or equal to 0.5 ppm_.This method was applied to the analysis of samples from a chlorpyrifos-exposed axolotl, demonstrating its use as an analytical tool for toxicological studies.     

Determination of organochlorine and organophosphorus pesticide residues in low moisture, nonfatty products using a solid phase extraction cleanup and gas chromatography

A multiresidue solid-phase extraction (SPE) method for the isolation and subsequent gas chromatographic determination of organochlorine and organophosphorus pesticide residues in low-moisture, nonfatty products is described. Residues are extracted from samples with an acetonitrile/water mixture. Cleanup of the extract is performed using graphitized carbon black and anion exchange SPE columns, and analysis is performed by gas chromatography with Hall electrolytic conductivity and flame photometric detection. Recovery data was obtained by fortifying corn, oats and wheat with pesticides. The average recoveries were 79-123% for eight organochlorine and 51-122% for 28 organophosphorus pesticide residues. The limit of quantitation for chlorpyriphos was 0.05 ppm using the Hall electrolytic conductivity detector and < 0.005 ppm using the flame photometric detector.     

Testing the efficiency of extraction of incurred residues from soil with optimized multi-residue method

The reproducibility of extraction of residues from spiked soil samples and from soils containing incurred residues was tested with ¹⁴C-labeled test compounds of different physical-chemical properties. Nearly 100% of the compounds added to the sample before extraction could be recovered with an average reproducibility relative standard deviation (CV) of 5.4%. The additional steps of the determination process (cleanup, evaporation, etc.) contributed to the major part of the variability of the results (CV = 10–20%). The incurred residues were most efficiently extracted with acetone for 30 min followed by the mixture of acetone/ethyl acetate 1:1 for additional 30 min. However, they could only be recovered at various extent (64–90% of total residues), underlying the importance of testing the efficiency of extraction. The residues were identified and quantified by gas chromatography applying thermionic detector. The performance parameters of the method complied with the international method validation guidelines, and they proved to be robust and suitable for determination of pesticide residues in soils of widely different physical–chemical properties.     

Minimization of blank values of the miniature silica gel column

Several methods involving silica gel separations of polychlorinated biphenyls from chlorinated insecticides are already described in literature. Our intention was to find a system of solvent and silica gel of the lowest blank values. The first step was to find a solvent mixture which will keep the homogenity of a silica gel column. PCBs elution was performed with pentane, while the chlorinated insecticides eluated with diethylether, acetone, methanol, and benzene. The elution of pesticides gave the best results for the following solvent systems: diethylether + hexane (1:1), acetone + hexane (1:4), methanole + pentane (1:8) and benzene.Separation of pesticides from polychlorinated biphenyls found in a synthetic mixture was also examined. It was found that all solvent systems used gave similar results of separation. However, only if benzene is used as eluant, the silica gel column can be used for four successive separations after the “on column” regeneration. In order to obtain the lowest blank values silica gel was cleaned with several solvents. The eluates after the silica gel separation were also cleaned up by means of deactivation alumina and concentrated sulphuric acid.     

LC-MS/MS determination of pesticide residues in fruits and vegetables

The aim of the research is to evaluate pesticide residue contamination of fresh and frozen fruits and vegetables, agricultural raw material, purchased from Polish farmers for production of frozen fruits and vegetables, and the estimation of the multiresidue method effectiveness expressed as the proportion of pesticides detected in food samples to the total number of pesticides analyzed by multiresidue methods. A total of 144 samples (of black currants, red currants, raspberries, cherries, strawberries, blackberries, cauliflowers and broccoli) were analyzed using LC-MS/MS method for the determination of 60 pesticides. QuEChERS extraction, matrix-matched calibration and dynamic multiple reaction monitoring method were used. Residues of 15 compounds, mainly fungicides and insecticides, were detected in 46 samples. The percentage of samples with residues above the maximum residue levels (MRL) was 15%, whereas samples with residues below MRL were 17%. A total of 13 samples contained more than one pesticide residue. Pesticide residues were detected most often in samples of black currants (50%), broccoli (36.4%), raspberries (29%) and red currants (21.8%). The most frequently detected pesticides were carbendazim and acetamiprid. The proportion of pesticides detected during our study to the total number of analyzed pesticides amounted to 25%. It was compared to literature findings. For three fourth of multiresidue methods, the proportion was below 50% for methods developed for the analysis of less than 100 pesticides, and below 30% for methods developed for the analysis of more than 100 pesticides. It appears that a lot of efforts and means is lost on pesticides never or rarely detected in examined samples. The workload and cost effectiveness of the development and application of multiresidue methods along with the range of pesticides covered by the method should be carefully and thoroughly considered anytime when a new method or workflow is developed. Including non-targeted screenings in pesticide residue control seems to be an alternative worth considering.     

Simultaneous determination of organochlorine and pyrethriod pesticide residues in the Chinese patent medicines by gas chromatography-tandem mass spectrometry

A simple, sensitive, reliable method was developed for the simultaneous determination of organochlorine and pyrethriod pesticide residues in Chinese patent medicines Six ingredient rehmannia pills and Xiaoyao pills. These pesticides were extracted by ethyl acetate. The extraction time and volume of ethyl acetate were optimized. Cleanup of extracts was performed with dispersive-solid phase extraction using graphitized carbon black as the sorbent. The determination of pesticides in the final extracts was carried out by gas chromatography–tandem mass spectrometry in multiple reaction monitoring mode (GC-MS/MS, MRM). The linearity of the calibration curves is good in matrix-matched standard and yields the coefficients of determination (R²) ≥0.99 for all of the target analytes. Under optimized conditions, the average recoveries (five replicates) for most pesticides range from 75.5% to 114.6%, and RSDs are less than 10.0%. The LODs of 18 pesticides in Six ingredient rehmannia pill and Xiaoyao pills are in the range of 0.01–8.82 μg kg^?1. The developed method meets the requirements of pesticide residue analysis and could be effectively used for routine analysis of the organochlorine and pyrethriod pesticide residues in Six ingredient rehmannia pills and Xiaoyao pills.     

Headspace solid phase microextraction method for determination of triazine and organophosphorus pesticides in soil

A headspace solid phase microextraction method (HS-SPME) for simultaneous determination of five pesticides belonging to triazine and organophosphorus pesticide groups in soil samples was developed. Microextraction conditions, such as temperature, extraction time and sodium chloride (NaCl) content were investigated and optimized using 100 μ m polydimethyl-siloxane (PDMS) fiber. Detection and quantification were done by gas chromatography-mass spectrometry (GC-MS). Relative standard deviation (RSD) and recovery values for multiple analysis of soil samples fortified at 30 μ g kg^{? 1} of each pesticide were below 13 % and higher than 70 %, respectively. Limits of detection (LOD) for all the compounds studied were less than 3.2 μ g kg^{? 1}. The proposed method was applied in the analysis of some agricultural soil samples.     

Multiresidue method for high-performance liquid chromatography determination of carbamate pesticides residues in tea samples

A multiresidue method was developed to determine 19 carbamate pesticides in tea samples. Optimizations of different parameters, such as the type of extraction solvents, clean-up cartridges, and elution solvents were carried out. The developed method used acetonitrile as extraction solvent, amino cartridge for adsorbents and acetone-n-hexane as the eluting solution. Nineteen carbamate residues were then analyzed by high-pressure liquid chromatography (HPLC) with fluorescence detector. The present results showed good linearity by correlation coefficients of more than 0.9999 for all analyses. Limits of detection and quantification varied from 0.0005–0.023 mg L^{? 1}, 0.008–0.077 mg L^{? 1}, respectively. Recoveries of sixteen carbamate pesticides ranged from 65% to 135% at the spiked level of 0.5, 1.0 and 2.0 mg L^{? 1}. The relative standard deviations were lower than 20% and coefficient of variations were lower than 15%. The results indicate that the proposed method provides an effective multi and trace level screening determination of carbamate pesticides residues for tea samples.     

Pesticide residues in Portuguese strawberries grown in 2009–2010 using integrated pest management and organic farming

Pesticides are among the most widely used chemicals in the world. Because of the widespread use of agricultural chemicals in food production, people are exposed to low levels of pesticide residues through their diets. Scientists do not yet have a total understanding of the health effects of these pesticide residues. This work aims to determine differences in terms of pesticide residue content in Portuguese strawberries grown using different agriculture practices. The Quick, Easy, Cheap, Effective, Rugged, and Safe sample preparation method was conducted and shown to have good performance for multiclass pesticides extraction in strawberries. The screening of 25 pesticides residue was performed by gas chromatography?Ctandem mass spectrometry. In quantitative validation, acceptable performances were achieved with recoveries of 70?C120 and <12?% residual standard deviation for 25 pesticides. Good linearity was obtained for all the target compounds, with highly satisfactory repeatability. The limits of detection were in the range of 0.1?C28???g/kg. The method was applied to analyze strawberry samples from organic and integrated pest management (IPM) practices harvested in 2009?C2010. The results showed the presence of fludioxonil, bifenthrin, mepanipyrim, tolylfluanid, cyprodinil, tetraconazole, and malathion when using IPM below the maximum residue levels.     

Analysis of Organophosphorus Pesticides in Whole Milk by Solid Phase Microextraction Gas Chromatography Method

Solid phase microextraction (SPME) was used for the extraction of residual coumaphos and dichlorvos in whole milk. The residues were analyzed by capillary gas chromatography equipped with nitrogen phosphorus detector (GC-NPD). A manual SPME holder with a 100-μm polyacrylate fiber was used. The optimized conditions for extraction by SPME method were: sample agitation, absorption temperature of 30°C, absorption time of 40 min, desorption time of 10 min, and sample volume was 16.0 mL in the vial. Under these conditions, the calibration graphs were linear in the range of 0.17 μgL^?1 to 1.75 μgL^?1 for coumaphos and 0.69 μgL^?1 to 6.90 μgL^?1 for dichlorvos. Precision was good with RSD values of 13% for coumaphos and 14% for dichlorvos. The detection limits (LOD) were 0.060 μgL^?1 for dichlorvos and 0.052 for coumaphos. The quantification limits (LOQ) were 0.086 μgL^?1 for dichlorvos and 0.066 μgL^?1 for coumaphos. The results obtained in this study suggest that SPME is a suitable technique for residual pesticide analysis of milk. The data demonstrate that particular OP pesticides used in dairy farming in the region of Minas Gerais were found to contaminate cow whole milk, and the residues are not removed by treating the milk by boiling.     

Rapid determination of residues of pesticides in honey by µGC-ECD and GC-MS/MS: Method validation and estimation of measurement uncertainty according to document No. SANCO/12571/2013

A simple and straightforward method for simultaneous determination of residues of 13 pesticides in honey samples (acrinathrin, bifenthrin, bromopropylate, cyhalothrin-lambda, cypermethrin, chlorfenvinphos, chlorpyrifos, coumaphos, deltamethrin, fluvalinate-tau, malathion, permethrin and tetradifon) from different pesticide classes has been developed and validated. The analytical method provides dissolution of honey in water and an extraction of pesticide residues by n-Hexane followed by clean-up on a Florisil SPE column. The extract was evaporated and taken up by a solution of an injection internal standard (I-IS), ethion, and finally analyzed by capillary gas chromatography with electron capture detection (GC-µECD). Identification for qualitative purpose was conducted by gas chromatography with triple quadrupole mass spectrometer (GC-MS/MS). A matrix-matched calibration curve was performed for quantitative purposes by plotting the area ratio (analyte/I-IS) against concentration using a GC-µECD instrument. According to document No. SANCO/12571/2013, the method was validated by testing the following parameters: linearity, matrix effect, specificity, precision, trueness (bias) and measurement uncertainty. The analytical process was validated analyzing blank honey samples spiked at levels equal to and greater than 0.010 mg/kg (limit of quantification). All parameters were satisfactorily compared with the values established by document No. SANCO/12571/2013. The analytical performance was verified by participating in eight multi-residue proficiency tests organized by BIPEA, obtaining satisfactory z-scores in all 70 determinations. Measurement uncertainty was estimated according to the top-down approaches described in Appendix C of the SANCO document using the within-laboratory reproducibility relative standard deviation combined with laboratory bias using the proficiency test data.     

Surface and ground waters characterization in Tuscany (Italy) by using algal bioassay and pesticide determinations: comparative evaluation of the results and hazard assessment of the pesticides impact on primary productivity

Algal bioassays and pesticide analysis were joined in Tuscany regional monitoring of surface and ground waters. Results were compared. Waters affected algal growth in any of the following ways: stimulation, inhibition, stimulation at low concentrations and inhibition at higher concentrations. Most of ground waters inhibited algal growth whereas only a little percentage were contaminated with pesticide. Most of surface waters stimulated algal growth and a higher percentage were contaminated with pesticides. In waters with inhibitory effect toxicological parameters (EC50, EC25, EC10 and NOEC) were measured and compared; EC25 values were very close to NOEC values. Hazard to aquatic primary productivity for each pesticide found during chemical monitoring was evaluated; for this aim the margin of safety (MOS) was calculated by using algal toxicity and the pesticide concentration measured.     

百菌清农药残留的SPE-GC检测

对环境水样中百菌清农药残留进行了SPE-GC分析方法研究。环境水样通过Florisil柱富集、净化,3 mL乙酸乙酯洗脱,GC-ECD进行分析检测。实验表明,百菌清农药残留在0.01~10 mg/L范围内线性关系良好,相关系数为0.9993。外标法定量,检出限为0.0035 mg/L,对实际水样进行加标回收,回收率范围在93.47%~100.14%之间,6次重复测定相对标准偏差在3.97%~4.96%之间,并将方法应用于周边环境地表水的检测。该方法具有简便,快速,准确,灵敏度高等特点,能满足环境水样中农药残留分析要求。     

Part I: Temporal and spatial distribution of multiclass pesticide residues in lake waters of Northern Greece: application of an optimized SPE-UPLC-MS/MS pretreatment and analytical method

The present work describes the application of an analytical procedure, utilizing ultra performance liquid chromatography (UPLC) coupled with mass spectrometry instrumentation, for the determination of 253 multiclass pesticides, classified in six different groups. Solid phase extraction was applied for the isolation and pre-concentration of target compounds in water samples. Surface waters of the lakes located in Northern Greece (Volvi, Doirani, and Kerkini), were collected in two time periods (fall/winter 2010 and spring/summer 2011) and analyzed, applying the developed analytical methods. Spatial distribution of detected pesticides was visualized using interpolation methods and geographical information systems (GIS). Pesticides with maximum concentrations were amitrole, propoxur, simazine, chlorpyrifos, carbendazim, triazophos, disulfoton-sulfone, pyridaben, sebuthylazine, terbuthylazine, atrazine, atrazine-desethyl, bensulfuron-methyl, metobromuron, metribuzin, rotenone, pyriproxyfen, and rimsulfuron. In Lake Kerkini, mainly carbamates and triazines were determined at elevated concentrations, near the coastal point of the NW side of the lake. Seasonal variations were strong among the applied pesticide classes and determined concentrations, indicating the contribution of pesticide application patterns and rainfall. Lake Doirani exhibited organophosphate pesticides at higher concentrations mainly at coastal points, while triazines emerged as the main pollutant during spring sampling. Lake Volvi exhibited the highest pesticide concentrations, mostly triazines and ureas at the central part of the lake. The occurrence of extreme values and nonconstant seasonal variations indicated that the concentrations were increased disproportionately during the second sampling, as a result of the varying contribution of pollution sources right after the application period. In all cases, the total concentration of pesticides increased during the second sampling period.     

Multiresidue determination of pesticides in tea by gas chromatography-tandem mass spectrometry

An efficient and reliable GC-MS/MS method for the multiresidue determination of pesticides in tea was developed by modifying the Japanese official multiresidue method. Sample preparation was carefully optimized for the efficient removal of coextracted matrix components. The optimal sample preparation procedure involved swelling of the sample in water; extraction with acetonitrile; removal of water by salting-out; and sequential cleanup by ODS, graphitized carbon black/primary secondary amine (GCB/PSA) and silica gel cartridges prior to GC-MS/MS analysis. The recoveries of 162 pesticides from fortified (at 0.01 mg kg^?1) green tea, oolong tea, black tea and matcha (powdered green tea) were mostly (95–98% of the tested pesticides) within the range of 70–120%, with relative standard deviations of <20%. Poor recovery of triazole pesticides was considered to be due to low recovery from the silica gel cartridges. The test solutions obtained by the modified method contained relatively small amounts of pigments, caffeine and other matrix components and were cleaner than those obtained by the original Japanese official multiresidue method. No interfering peaks were observed in the blank chromatograms, indicating the high selectivity of the modified method. The overall results suggest that the developed method is suitable for the quantitative analysis of GC-amenable pesticide residues in tea.     

Application of automated mass spectrometry deconvolution and identification software for pesticide analysis in surface waters

A new approach to surface water analysis has been investigated in order to enhance the detection of different organic contaminants in Nathan Creek, British Columbia. Water samples from Nathan Creek were prepared by liquid/liquid extraction using dichloromethane (DCM) as an extraction solvent and analyzed by gas chromatography mass spectrometry method in scan mode (GC-MS scan). To increase sensitivity for pesticides detection, acquired scan data were further analyzed by Automated Mass Spectrometry Deconvolution and Identification Software (AMDIS) incorporated into the Agilent Deconvolution Reporting Software (DRS), which also includes mass spectral libraries for 567 pesticides. Extracts were reanalyzed by gas chromatography mass spectrometry single ion monitoring (GC-MS-SIM) to confirm and quantitate detected pesticides. Pesticides: atrazine, dimethoate, diazinone, metalaxyl, myclobutanil, napropamide, oxadiazon, propazine and simazine were detected at three sampling sites on the mainstream of the Nathan Creek. Results of the study are further discussed in terms of detectivity and identification level for each pesticide found. The proposed approach of monitoring pesticides in surface waters enables their detection and identification at trace levels.     

Transfer of pesticides to the brew during mate drinking process and their relationship with physicochemical properties

In order to evaluate the extraction of pesticide residues that are transferred to the brew during mate drinking process of P.U.1 yerba mate leaves (Ilex paraguariensis), a special device to simulate the way in which mate is drunk in Uruguay was developed. The transfer to the brew of 12 organophosphates, 5 synthethic pyrethroids and one organochlorine pesticide from spiked samples was studied. The relationship between the transfer data thus obtained and physicochemical properties like water solubility (Ws), octanol-water coefficient (Kow) and Henry's constant (H) was evaluated. The extractability of the pesticide residues from yerba mate can be correlated with log Ws and log Kow. These transfer values allowed the calculation of ARLs (acceptable residue level) for the pesticides following Food and Agriculture Organization (FAO), World Health Organizaion (WHO) guidelines. These results can help the future establishment of maximum residue levels (MRLs).