Diffusion of PAH and PCB from contaminated sediments with and without mineral capping; measurement and modelling

A novel laboratory microcosm test was developed to measure the diffusion of native PAHs and PCBs from sediments in the presence and absence of a capping layer. Diffusive flux of 15 PAHs and 7 PCBs from uncapped sediment from Oslo harbour was 3.8+/-0.9 microg m(-2)d(-1) and 0.010+/-0.003 microg m(-2)d(-1), respectively. The flux from sediments capped with 1cm mineral cap (crushed limestone or crushed gneiss (0-2mm)), observed during the first 410 d, was 3.5-7.3% of the flux from uncapped sediments. By measuring freely dissolved pore water concentrations of 10 PAHs the flux in the microcosm was modelled with steady state and transient diffusion models. The measured flux from uncapped sediment was 27-290% of modelled steady state flux. Good agreement was also found between the measured flux of pyrene from capped sediment and the flux modelled with the transient model when fitting only with the distribution coefficients for pyrene between the cap material and water (Kd_pyr). Fitted Kd_pyr, (210 and 23 l kg(-1) for limestone and gneiss, respectively) was in the same order of magnitude as K(d) calculated from organic carbon content in the cap materials (68 and 14 l kg(-1) respectively). Calculation of the efficiency of a hypothetical cap with 10 cm diffusion path shows that the increased diffusion path length alone can yield a flux reduction >99% through a strong increase in the stagnant diffusive boundary layer from <1 to 100mm.     

Measuring the flux at the interface of coal-tar impacted sediment and river water near a former MGP site

Determining water movement through contaminated sediment is critical for characterizing transport of chemicals from the sediment to the overlying water. Field studies to characterize the water flow across the sediment-water interface within a river adjacent to a former manufactured gas plant site were conducted. For this purpose, a new design of an interfacial flow meter was developed and tested. The in situ components of the system consisted of: a cylinder with an interfacial area of 2342 cm2; a dome attached to the cylinder; and a flow tube that allows water to flow from inside the dome to the river at the rate equal to the specific discharge across the sediment-water boundary. A 'heat-pulse' method was used to measure flow by heating the center of the flow tube for a brief time period and measuring the temperature profile within the tube over time. The system was calibrated to measure volumetric flux in the range 1.5-4.0 cm d(-1), however using a flow-addition method, the measurement of lower velocities also was accomplished, and calibration at higher fluxes is possible. From the groundwater flow at the interface of the coal-tar impacted sediment and information on the sediment pore water concentrations of several PAHs (poly-cyclic aromatic hydrocarbons), the mass flux of these PAHs to the river were estimated. Information on PAH mass flux at the sediment-water interface is useful for site assessment, including the evaluation of remediation alternatives and longer term site characterization.     

Contamination by polycyclic aromatic hydrocarbons in the Jiulong River Estuary and Western Xiamen Sea, China

The distribution of 16 polycyclic aromatic hydrocarbons (PAHs) was determined in water, sediment and pore water of the Jiulong River Estuary and Western Xiamen Sea, China. Total PAH concentrations varied from 6.96 to 26.9 microg/l in water, 59-1177 ng/ g dry weight in surficial sediments, and 158-949 microg/l in pore water. The PAHs were present in higher levels in pore water than in surface water, due possibly to higher concentrations of dissolved organic carbon or colloids with which the hydrophobic pollutants were strongly associated. Such a concentration gradient implies a potential flux of pollutants from sediment pore water to overlying water. The levels of PAHs in water and pore water were significantly higher than those found in 1998, suggesting recent inputs of these compounds into the area and re-working of sediment phase. The composition pattern of PAHs in the three phases was dominated by high molecular weight PAHs, in particular 5-ring PAHs. The salinity profile of dissolved PAHs suggested that they all behaved non-conservatively due to deviation from the theoretical dilution line. No correlation was found between PAH concentrations in sediment and those in pore water, and the correlation between the partition coefficients of PAHs and sediment organic carbon content was not significant, suggesting the complexity of the partition behaviour of PAHs. As a result of high PAH concentrations in water and pore water, it is likely that they may have caused mortality to certain exposed organisms.     

Phytoremediation prospects of willow stands on contaminated sediment: a field trial

Establishing fast growing willow stands on land disposed contaminated dredged sediment can result in the revaluation of this material and opens possibilities for phytoremediation. A field trial was designed to assess the impact of planting a willow stand (Salix viminalis L. 'Orm') on the dissipation of organic contaminants (mineral oil and PAHs) in dredged sediment. In addition, the accumulation of heavy metals (Cd, Cu, Pb and Zn) in the biomass was determined. After 1.5 years, a significant decrease of 57% in the mineral oil concentration in the sediment planted with willow was observed. Degradation of mineral oil in sediment which was left fallow, was only 15%. The mineral oil degradation under willow was most pronounced (79%) in the root zone of the stand. In the sediment which was left fallow there was a significant reduction of the total PAH content by 32% compared with a 23% reduction in the planted sediment. The moderate and selective metal uptake, measured in this study, limits the prospects for phytoextraction of metals from dredged sediment.     

Application of a combined measurement and modeling method to quantify windblown dust emissions from the exposed playa at Mono Lake, California

Particulate matter < or =10 microm (PM10) emissions due to wind erosion can vary dramatically with changing surface conditions. Crust formation, mechanical disturbance, soil texture, moisture, and chemical content of the soil can affect the amount of dust emitted during a wind event. A refined method of quantifying windblown dust emissions was applied at Mono Lake, CA, to account for changing surface conditions. This method used a combination of real-time sand flux monitoring, ambient PM10 monitoring, and dispersion modeling to estimate dust emissions and their downwind impact. The method identified periods with high emissions and periods when the surface was stable (no sand flux), even though winds may have been high. A network of 25 Cox sand catchers (CSCs) was used to measure the mass of saltating particles to estimate sand flux rates across a 2-km2 area. Two electronic sensors (Sensits) were used to time-resolve the CSC sand mass to estimate hourly sand flux rates, and a perimeter tapered element oscillating microbalance (TEOM) monitor measured hourly PM10 concentrations. Hourly sand flux rates were related by dispersion modeling to hourly PM10 concentrations to back-calculate the ratio of vertical PM10 flux to horizontal sand flux (K-factors). Geometric mean K-factor values (K(f)) were found to change seasonally, ranging from 1.3 x 10(-5) to 5.1 x 10(-5) for sand flux measured at 15 cm above the surface (q15). Hourly PM10 emissions, F, were calculated by applying seasonal K-factors to sand flux measurements (F = K(f) x q15). The maximum hourly PM10 emission rate from the study area was 76 g/m2 x hr (10-m wind speed = 23.5 m/sec). Maximum daily PM10 emissions were estimated at 450 g/m2 x day, and annual emissions at 1095 g/m2 x yr. Hourly PM10 emissions were used by the U.S. Environmental Protection Agency (EPA) guideline AERMOD dispersion model to estimate downwind ambient impacts. Model predictions compared well with monitor concentrations, with hourly PM10 ranging from 16 to over 60,000 microg/m3 (slope = 0.89, R2 = 0.77).     

Spatial and seasonal variations of polycyclic aromatic hydrocarbons in Haihe Plain, China

A dynamic fugacity model was developed to simulate the spatial and seasonal variations of PAHs in Haihe Plain, China. The calculated and measured concentrations exhibited good consistency in magnitude with deviations within a factor of 4 in air and 2 in soil. The spatial distributions of PAHs in air were mainly controlled by emission while the seasonal variations were dominated by emission and gas-particle partition. In soil, the spatial distributions of PAHs were controlled by the soil organic carbon content while the seasonal variations were insignificant. The severest soil contamination was observed in Shanxi and followed by the southwest of Hebei province. Transfer fluxes of total PAHs between air and soil were calculated. The spatial distribution of air-to-soil flux was closely related to the landcover while the soil-to-air flux changed with soil organic matter content. Monte Carlo simulation was done to evaluate the uncertainty of the estimated results in air.     

Dissipation of PAHs in saturated, dredged sediments: a field trial

Sediments dredged from navigable rivers often contain elevated concentrations of recalcitrant, potentially toxic organic compounds such as polychlorinated biphenyls (PCBs) and polyaromatic hydrocarbons (PAHs). The presence of these compounds often requires that the sediments be stored in fully contained disposal facilities. A 3-year field study was conducted at the Jones Island disposal facility in Milwaukee, Wisconsin, to compare bioremediation of PAHs in contaminated dredged sediments in the absence of plants to phytoremediation with Salix nigra (black willow) (SX61), Spartina pectinata (prairie cord grass), Carex aquatalis (lake sedge), Lolium multiflorum (annual rye), and Scirpus fluviatilis (bulrush). Nine PAHs were detected initially in the sediments. Over the 3-year experiment, acenaphthene dissipation ranged from 94% to 100%, whereas anthracene, benzo[a]pyrene and indo[1,2,3-cd]pyrene generally had modest decreases in concentration (0-30% decrease). The remaining five PAHs ranged in degree of disappearance from 23% to 82%. Planted treatments did not enhance PAH dissipation relative to those without plants, but treatments with high biomass yield and high transpiration plant species had significantly less removal of PAHs than unplanted controls. Significant, negative correlations between nitrogen removal and decreases in PAH concentration suggest that competition for nutrients between plants and microorganisms may have impeded the microbial degradation of PAHs in the rhizosphere of the more rapidly growing plant species.     

Laboratory studies to characterize the efficacy of sand capping a coal tar-contaminated sediment

Placement of a microbial active sand cap on a coal tar-contaminated river sediment has been suggested as a cost effective remediation strategy. This approach assumes that the flux of contaminants from the sediment is sufficiently balanced by oxygen and nutrient fluxes into the sand layer such that microbial activity will reduce contaminant concentrations within the new benthic zone and reduce the contaminant flux to the water column. The dynamics of such a system were evaluated using batch and column studies with microbial communities from tar-contaminated sediment under different aeration and nutrient inputs. In a 30-d batch degradation study on aqueous extracts of coal tar sediment, oxygen and nutrient concentrations were found to be key parameters controlling the degradation rates of polycyclic aromatic hydrocarbons (PAHs). For the five PAHs monitored (naphthalene, fluorene, phenanthrene, anthracene, and pyrene), degradation rates were inversely proportional to molecular size. For the column studies, where three columns were packed with a 20-cm sand layer on the top of a 5 cm of sediment layer, flow was established to sand layers with (1) aerated water, (2) N(2) sparged water, or (3) HgCl(2)-sterilized N(2) sparged water. After steady-state conditions, PAH concentrations in effluents were the lowest in the aerated column, except for pyrene, whose concentration was invariant with all effluents. These laboratory scale studies support that if sufficient aeration can be achieved in the field through either active and passive means, the resulting microbially active sand layer can improve the water quality of the benthic zone and reduce the flux of many, but not all, PAHs to the water column.     

Sedimentary record of PAHs in the Liangtan River and its relation to socioeconomic development of Chongqing, Southwest China

Concentrations of polycyclic aromatic hydrocarbons (PAHs) were detected in sediment cores and surface sediment samples from the Liangtan River of Chongqing, Southwest China. The total concentration of 16 PAHs ranged from 69 to 6251 ng g⁻¹. The spatial distribution of the PAHs reflects the intensity and scope of human activity in the catchment. A historical record of PAH contamination was reconstructed using a sediment core from a background segment of the river. The characteristic changes of concentrations, fluxes and patterns of 16 PAHs over the past ∼90 years were captured in detail. An obvious peak of PAH concentration and flux was found in the 1940s, i.e., during war time, and then a sharp increase was observed from the early 1980s to the present. The maximum concentration and flux reached 1260 ng g⁻¹ and 470 ng cm⁻² year⁻¹, respectively. The sharp increase was attributed to the contribution of pyrogenic sources of PAHs. The population, length of highways and energy consumption of Chongqing, as indexes of socioeconomic development, were positively correlated with PAH input in the sediment core from the 1950s to the present. The results clearly show that the local socioeconomic development in the last decades remarkably aggravated the environmental load of sedimentary PAHs.     

Mercury transport between sediments and the overlying water of the St. Lawrence River area of concern near Cornwall, Ontario

Contaminated sediments in the St. Lawrence River remain a difficult problem despite decreases in emissions. Here, sediment and pore water phases were analyzed for total mercury (THg) and methyl mercury (MeHg) and diffusion from the sediment to the overlying water was 17.5 ± 10.6 SE ng cm⁻² yr⁻¹ for THg and 3.8 ± 1.7 SE ng cm⁻² yr⁻¹ for MeHg. These fluxes were very small when compared to the particle-bound mercury flux accumulating in the sediment (183 ± 30 SE ng cm⁻² yr⁻¹). Studies have reported that fish from the westernmost site have higher Hg concentrations than fish collected from the other two sites of the Cornwall Area of Concern, which could not be explained by differences in the Hg flux or THg concentrations in sediments, but the highest concentrations of sediment MeHg, and the greatest proportions of MeHg to THg in both sediment and pore water were observed where fish had highest MeHg concentrations.     

Evaluating contamination of dredges and disposal criteria in Greek coastal areas

Sediments were collected from areas that were going to be dredged located at six small Greek ports, as well as from possible disposal areas. In order to assess the contamination level of dredged material, the samples were analysed for pH, organic matter, the metals Cd, Pb, Hg, Cr, Ni, Cu, Zn and major organic compounds (PAHs, PCBs). The sediments' quality was evaluated by two approaches: (i) by classifying each area according to two sets of Sediment Quality Guidelines (SQGs) and (ii) by calculating the contamination factors and degree for each area. The results showed that organic compounds were detected in trace amounts in 14% of the port samples belonging to the PAHs group. The characterization of the sediment samples was based on the metals' concentration showing that the majority of the areas to be dredged (80%) are classified as of medium-low contamination according to the SQGs. However, according to the contamination degree, only 30% of the areas are classified as of low contamination, while 40% as of moderate contamination and 30% of the areas as of considerable contamination. From the point of view of "no disturbance" of the ecosystem, decisions about dumping should be taken only after evaluating the material to be dredged. If the SQGs are exceeded, dumping must be forbidden. Otherwise, further evaluation is needed based on the comparison with the receiving area, i.e. by estimating the contamination degree. Dumping could be allowed if the contamination degree is found to be below moderate.     

Impact of dredged urban river sediment on a Saronikos Gulf dumping site (Eastern Mediterranean): sediment toxicity,contaminant levels,and biomarkers in caged mussels

Impacts of chemical contaminants associated with dumping of dredged urban river sediments at a coastal disposal area in Saronikos Gulf (Eastern Mediterranean) were investigated through a combined approach of sediment toxicity testing and active biomonitoring with caged mussels. Chemical analyses of aliphatic hydrocarbons (AHs), polycyclic aromatic hydrocarbons (PAHs), Cu, and Zn in combination with the solid phase Microtox® test were performed on sediments. Concentrations of PAHs, AHs, Cu, and Zn as well as multiple biomarkers of contaminant exposure and/or effects were measured in caged mussels. Sediments in the disposal and neighboring area showed elevated PAHs and AHs concentrations and were characterized as toxic by the solid-phase Microtox® test during and after dumping operations. Biomarker results in the caged mussels indicated sublethal effects mainly during dumping operations, concomitantly with high concentrations of PAHs and AHs in the caged mussel tissues. Cu and Zn concentrations in sediments and caged mussels were generally not elevated except for sediments at the site in the disposal area that received the major amount of dredges. High PAHs and AHs levels as well as sublethal effects in the caged mussels were not persistent after termination of operations. The combined bioassay–biomarker approach proved useful for detecting toxicological impacts of dredged river sediment disposal in sediments and the water column. Nevertheless, further research is needed to evaluate whether sediment toxicity will have long-term effects on benthic communities of the disposal area.     

Apply appropriate models in the study of dry deposition fluxes of particulate matter and polycyclic aromatic hydrocarbons (PAHs) in Tsukuba, Japan

In this study, plates for downward flux and upward flux were used to measure atmospheric dry deposition fluxes for particulate mass and polycyclic aromatic hydrocarbons (PAHs) in TERC (Tsukuba), Japan. Ambient particles concentrations were also collected using a high-volume air sampler, and ambient particle size distributions between 0.01 μm and 13.1 μm were measured using a low-pressure cascade impactor to characterise the PAHs levels and dry deposition. The results indicated that the average cumulative fraction of dry deposition flux for particles and PAHs which attached with them was caused by the particle size of greater than 1.2-6.3 μm (97%).     

Metal solubility as a function of pH in a contaminated, dredged sediment affected by oxidation

The solubility as a function of pH for metals in a reduced dredged sediment, subjected to different redox conditions, was studied in a laboratory experiment. The redox conditions imposed simulated (i) the undisturbed sediment (flooded), (ii) a dredged material stored in a confined pond (aerated once and then flooded), (iii) an upland stored dredged material (drained and dried), and (iv) an upland stored sediment subjected to tillage (drained, dried and mixed). Minor differences in the solubility as a function of pH were observed between the treatments after two weeks. After three months, the solubility of Cd, Cu, Pb and Zn increased strongly in the oxidized sediments. Leachability of Fe decreased, while Mn, Ni and Co were mostly unaffected. Both short- and long-term mobility of metals (except Fe) is expected to be lowest when a reduced sediment remains in reduced conditions. Studying the solubility as a function of pH may provide additional information on the chemical association of metals in sediments.     

Volatilization of contaminants from suspended sediment in a water column during dredging

Remedial dredging of contaminated bed sediments in rivers and lakes results in the suspension of sediment solids in the water column, which can potentially be a source for evaporation of hydrophobic organic compounds (HOCs) associated with the sediment solids. Laboratory experiments were conducted in an oscillating grid chamber to simulate the suspension of contaminated sediments and flux to air from the surface of the water column. A contaminated field sediment from Indiana Harbor Canal (IHC) and a laboratory-inoculated University Lake (UL) sediment, Baton Rouge, LA, were used in the experiments, where water and solids concentration and particle size distribution were measured in addition to contaminant fluxes to air. A transient model that takes into account contaminant desorption from sediment to water and evaporation from the water column was used to simulate water and sediment concentrations and air fluxes from the solids suspension. In experiments with both sediments, the total suspended solids (TSS) concentration and the average particle diameter of the suspended solids decreased with time. As expected, the evaporative losses were higher for compounds with higher vapor pressure and lower hydrophobicity. For the laboratory-inoculated sediment (UL), the water concentrations and air fluxes were high initially and decreased steadily implying that contaminant release to the water column from the suspended solids was rapid, followed by evaporative decay. For the field sediments (IHC), the fluxes and water concentrations increased initially and subsequently decreased steadily. This implied that the initial desorption to water was slow and that perhaps the presence of oil and grease and aging influenced the contaminant release. Comparison of the model and experimental data suggested that a realistic determination of the TSS concentration that can be input into the model was the most critical parameter for predicting air emission rates.     

Dynamics of PAH deposition, cycling and storage in a mixed-deciduous (Quercus-Fraxinus) woodland ecosystem

Estimates of standing biomass and fluxes of biomass in a mixed-deciduous woodland were derived, and used with results for concentrations of seven polycyclic aromatic hydrocarbons (PAHs) in different compartments of the woodland system to quantitatively assess some of the key fluxes and burdens of PAHs in this complex system. We quantified PAH burdens in air, in leaves of three deciduous tree species, in leaf litter and in soil, and uptake of PAHs by the tree leaves; PAH fluxes in litterfall, and deposition to the litter layer on the woodland floor during winter were calculated from these data. Air burdens exhibited marked seasonal variations for all compounds, with lowest values in summer when combustion-related emissions were low. Leaves did not accumulate large burdens of PAHs while on the trees and consequently, litterfall-associated fluxes of PAHs were small, representing only a fraction of the burdens in the litter layer to which they were deposited. Higher PAH burdens in air in winter, combined with the organic-matter-rich nature of the litter layer, are thought to be responsible for fluxes of PAHs to the litter layer in winter being 20-170 times the peak litterfall fluxes. The soil compartment was calculated to contain 25 years' worth of deposition of benzo[ghi]perylene, the most recalcitrant PAH in this study. Storage quotients for fluoranthene, pyrene, benzo[k]fluoranthene and benzo[a]pyrene burdens in soil represented 7-10 years' worth of deposition, while fluorene and phenanthrene storage in soil approached unity with inputs (1 and 3 years' worth of deposition, respectively). The relative importance of storage and loss processes was therefore closely related to the physico-chemical properties of the PAH, and is discussed in relation to the cycling of carbon in the woodland.     

Flux measurements of volatile organic compounds by the relaxed eddy accumulation method combined with a GC-FID system in urban Houston,Texas

A tall tower flux measurement setup was established in metropolitan Houston, Texas, to measure trace gas fluxes from emission sources in the urban surface layer. We describe a new relaxed eddy accumulation (REA) system combined with a dual-channel GC-FID used for VOC flux measurements, focusing on benzene, toluene, ethylbenzene and xylenes (BTEX) results. Ambient air sampled from 60 m above the ground next to a sonic anemometer was subsampled by a membrane pump and pushed into an REA valve system with two Teflon bag reservoirs, then transferred to two preconcentration units for thermal desorption. We discuss the performance of our system and the selected BTEX measurement results using approximately 8 weeks of data (May 22–July 22, 2008), presenting diurnal variations of concentrations and fluxes of these traffic tracers. The measured values exhibited diurnal cycles with dominant morning and midday peaks during weekdays related to rush hour traffic and additional weekday daytime toluene and xylenes emissions. Local evaporative emissions, likely from solvent usage, significantly contributed to the measured fluxes. We upscaled measured emissions to the county level using a high resolution land cover data set and compared the results with EPA’s National Emission Inventory (NEI).     

Experimental determination of efficiency of capping materials during consolidation of metal-contaminated dredged material

Capping has received considerable attention as a method to reduce contaminant transport from contaminated sediments and sub-aqueous disposed dredged materials. Consolidation of dredged material after capping can result in a substantial advection of pore water, into or through the capping layer. The effect of two different capping materials (crushed limestone and gneiss) on the transport of heavy metals and phosphorus during consolidation was studied with a novel experimental design. Capped dredged material was placed in a consolidation cell and pore water expelled during the consolidation was collected for chemical analysis. To support interpretation of the results from this test, interactions between the capping material and the dredged material were also studied in batch tests. The study revealed large differences in the capping efficiency (CE) between the two materials. Both materials were efficient caps for Fe and P (CE>99% with 2cm cap), while limestone also was efficient for Mn (CE>92% with 2cm cap). Contrary to what was expected, capping of dredged material with crushed gneiss increased the release of Ca, Mn, Co, Ni, Cd, and Cu, resulting in negative CE. The batch tests showed that leaching from the crushed gneiss was the source of the observed release of metals. The results also show that the high concentrations of heavy metals in the dredged material were immobilised, probably by sulphides. Protection against re-suspension and oxidation will therefore in many cases be the most important effect of the cap.     

Atmospheric deposition of polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans, and dioxin-like polychlorinated biphenyls in the Kanto Region, Japan

The atmospheric bulk (dry and wet) deposition of dioxins was investigated at four locations (Tokyo, Yokohama, Tsukuba, and Tanzawa) in the Kanto region (in Japan) over one year using a stainless-steel pot. Annual average polychlorinated dibenzo-p-dioxins/polychlorinated dibenzofurans (PCDD/PCDF) deposition fluxes were estimated to be from 450 to 1300 ng/m2/yr, and the annual average TEQ fluxes from 5.7 to 17 ng-TEQ/m2/yr at the four locations. The PCDD/PCDF deposition flux was higher in winter than in summer. The deposition flux could be related to ambient temperature, particularly for less chlorinated PCDDs/PCDFs, while the deposition flux is not necessarily related to the amount of precipitation. The PCDD/PCDF deposition flux increased as the particle deposition flux increased, for the winter samples. Based on the ratio of the PCDD/PCDF deposition fluxes to the particle deposition fluxes, the contribution of the reentrainment of soil particles to the TEQ of PCDD/PCDF deposition was considered to be negligible in this region. Based on the air concentrations monitored near our deposition sampling points by the municipalities, the ratio of the annual deposition flux to the annual average air concentration was roughly estimated to be 0.082 cm/s. The range of deposition flux in the Kanto region was estimated to be from 1.5 to 31 (median: 9.8) ng-TEQ/m2/yr based on the range of air concentration data measured by the municipalities. The total annual deposition flux in the entire Kanto region was estimated to range from 50 to 900 g-TEQ/yr (median 320 g-TEQ/yr). This estimated flux was of the same order as the sum of estimated emissions from municipal solid waste incinerators and industrial waste incinerators in the Kanto region. The contributions of dioxin-like PCBs in Yokohama, Tsukuba, and Tanzawa depositions were less than 10% of the total TEQ; however, in Tokyo it was almost equal to or more than 50%.     

Measurement of Hydrocarbon Emissions Fluxes from Refinery Wastewater Impoundments Using Atmospheric Tracer Techniques

Sulfur hexafluoride (SF6) tracer was used in a series of the experiments to simulate emissions of benzene, toluene, ethyl-benzene, and xylenes (BTEX) from a refinery wastewater basin. The ratio of the measured tracer release to the ambient tracer concentration established a dilution factor which was then used to calculate the mass flux of BTEX from the wastewater basin using the ambient BTEX concentration data. Measured fluxes of BTEX varied from 7 g/min to 70 g/min.

The CHEMDAT7 air emissions model was then used to predict emissions for comparison with the emissions measured using the tracer flux simulation. CHEMDAT7 typically overpredicted total measured BTEX emissions by factors of twelve to seventeen. The degree of overprediction varied both by the individual compound and the module of CHEMDAT7 used to predict emission fluxes.