等离子体场内CeO2催化降解甲醇的表面活性氧物种来源与作用研究

利用水热法制备了3种不同形貌(纳米棒、纳米颗粒、纳米立方体)的CeO_2催化剂,并通过比表面积测试(BET)、扫描电子显微镜(SEM)、拉曼光谱分析(Raman)、O_2程序升温脱附(O_2-TPD)手段表征其物理化学性质,结果发现,CeO_2纳米棒的表面氧空位和氧物种最多.等离子体与催化协同降解甲醇性能评价实验结果显示,CeO_2纳米棒展现出最好的催化性能.进一步设计实验(甲醇-TPD、不同气氛常温催化、催化剂内后置比较、O_3催化氧化)推测在等离子体场内CeO_2表面活性氧物种来源及其作用.结果表明:①在等离子体场内参与CeO_2表面催化反应的活性氧物种有两个来源,一是催化剂本身存在的表面氧物种,二是等离子体区域产生的短寿命物种及长寿命物种(主要是O_3),其中,O_3分解产生的活性氧物种是提高催化性能的主要因素.②不同形貌CeO_2由于表面氧空位含量不同,导致O_3在催化剂上分解产生的活性氧物种的量不同,最终影响等离子体催化性能.     

Pt颗粒负载对CeO2臭氧催化氧化甲苯的增强作用

通过铂颗粒吸附法制备得到Pt/CeO₂催化剂应用于臭氧催化氧化甲苯反应,研究了Pt颗粒负载对CeO₂臭氧催化氧化甲苯的增强作用.采用氢气程序升温还原(H₂-TPR)、氧气程序升温脱附(O₂-TPD)、X射线光电子能谱(XPS)和拉曼光谱(Raman)等手段对催化剂进行表征,结果显示,CeO₂负载Pt颗粒后,Pt与CeO₂存在相互作用,提高了CeO₂上氧空位的含量.臭氧分解实验证实了Pt/CeO₂催化剂具有更好的臭氧分解性能.臭氧催化氧化甲苯评价结果表明,Pt/CeO₂具有比CeO₂更优异的催化性能,在80℃时甲苯降解率、CO₂产率和臭氧分解率分别达到92.3%、92.1%和99.9%.原位拉曼进一步研究了臭氧分解生成的氧物种种类及含量,以及甲苯存在时氧物种的变化,结果表明,臭氧在氧空位上分解产生的过氧物种较为稳定,是氧化甲苯的重要活性物质.因此,P...     

Pt/CeO2催化氧化甲苯反应机制研究

采用浸渍法制备了Pt/CeO_2和Pt/Al2O_3催化剂,并通过XRD、BET、ICP-OES、H2-TPR、XPS等手段表征其物理化学性质.结果发现,Pt/CeO_2和Pt/Al2O_3催化剂上Pt负载量约为0.6%,Al2O_3载体上Pt颗粒尺寸更小,Pt/CeO_2的可还原性更强.甲苯催化氧化活性评价结果表明,Pt/CeO_2催化剂表现出更好的催化活性,T50=170℃,T90=190℃.通过UV-Raman、甲苯TPD、GC/MS、In-situ FTIR等手段进一步研究发现,Pt/CeO_2活化甲苯及反应供氧的机制与Pt/Al2O_3存在区别,其活性更好是因为:(1)负载在CeO_2表面存在高电子密度的Pt原子,具有更强的活化甲苯能力,可以直接使苯基和甲基间的C—C链发生断裂;(2)Pt的负载促进了CeO_2氧空位形成,进一步提高了CeO_2的储氧性能,加速氧循环.除了Pt解离气相氧之外,CeO_2还可以提供活性氧物种参与催化氧化甲苯的反应,进一步提高甲苯催化氧化效率.     

Pt颗粒尺寸对Pt/CeO2催化氧化甲苯性能影响

使用乙二醇还原法制备了一系列不同尺寸的Pt-x纳米颗粒(x=1.41、1.57、1.79、1.95、2.12、2.32 nm),将其负载于棒状(rod)CeO_2载体上.考察了不同尺寸的Pt颗粒催化剂Pt-x/CeO_2-rod在甲苯催化氧化反应中的催化性能.结果显示,随着Pt颗粒尺寸的增加,催化剂活性先升高后降低.其中,Pt颗粒尺寸为1.79 nm时催化剂催化活性最好,T90=133℃.一般认为,Pt颗粒尺寸增加其分散度减小,导致催化活性降低.然而本实验结果表明,随Pt尺寸增加催化活性先升高后降低,并且基于催化剂表面Pt原子计算的TOFs(turnover frequencies)随Pt尺寸增加逐渐变大.紫外拉曼光谱(UV Raman)、XRD、XPS显示,随着Pt颗粒尺寸增加,催化剂Pt-x/Ce-rod表面氧空位的浓度逐渐增加.氧空位有效提高了催化剂晶格氧的流动,促进了氧气的吸附活化及传递过程.Pt/Ce催化剂催化氧化甲苯反应活性是Pt分散度以及CeO_2表面氧空位浓度双重作用的结果.     

活性半焦表面负载CeO2纳米管的制备及其低温脱硝机理

基于Zn O纳米棒的自腐蚀机制,分别在活性半焦表面修饰负载了CeO_2纳米管、CeO_2纳米颗粒,并发现活性半焦表面CeO_2纳米管的低温脱硝性能明显优于CeO_2纳米颗粒。通过N2吸附、XRD、XPD、NH3-TPD、H2-TPR等一系列表征发现:与纳米颗粒相比,CeO_2纳米管由于其独特的结构形式,表面暴露较多Ce、O原子,具有较高Ce3+与化学吸附氧Oα比例,拥有更多的酸性位点和较强的酸性,有利于NH3、NO的表面吸附和氧化,从而表现出较好的低温脱硝性能。     

微波催化燃烧印刷包装VOCs废气的矿化途径与降解机理

结合贵金属和过渡金属催化剂的优点,采用等体积浸渍法制备了Pt-CuMnCeO_x/蜂窝纳米陶瓷整体式催化剂,考察其在微波辐照下对印刷包装VOCs（甲苯和丙酮）废气的矿化效果及催化机理.研究表明,微波功率600W,进气量5m³/h,甲苯和丙酮浓度各1000mg/m³条件下,催化剂床层温度达到300℃,双组分VOCs矿化率为82%.结合XRD和XPS表征可知,高分散的Pt颗粒与铜锰铈尖晶石活性组分在"微波热点"作用下提高了对甲苯、丙酮的低温催化效率;微波催化燃烧反应同时遵循L-H和MvK机理,不同价态金属间发生电子转移,催化剂表面产生更多的表面吸附氧和晶格氧,从而增强了VOCs分子的吸附与氧化.中间产物测试基础上,推测甲苯的氧化降解途径为甲苯→苯甲醛→苯甲酸→小分子酸→二氧化碳和水,丙酮的氧化降解途径为：丙酮→小分子醛类、酸类→二氧化碳和水.     

MCM-41孔径对负载MnOx催化氧化甲苯性能的影响

以3种不同孔径的介孔分子筛MCM-41（2.66、4.24和4.64 nm）为载体,采用等体积浸渍法制备MnO_x/MCM-41,考察了其催化氧化甲苯的活性,并用XRD、TEM、H₂-TPR、O₂-TPD和XPS等手段对催化剂进行表征.结果表明,增大载体孔径改变了锰元素的价态分布,提高了Mn³⁺和表面吸附氧的含量,使得催化剂的氧化还原性和晶格氧流动性也有所提升.因此,载体孔径从2.66 nm增大至4.64 nm后,MnO_x/MCM-41催化氧化甲苯的T90(体积空速=21200 h^-1)从369℃降至335℃.此外,还利用FTIR分析了甲苯的降解途径：甲苯先被活化脱氢,形成苯甲基,被吸附于催化剂表面;然后苯甲基被氧化为苯甲醇、苯甲醛和苯甲酸,随后苯环被破坏,苯甲酸裂解为马来酸、羧酸和甲酸等物质;最后被完全氧化为水和二氧化碳.     

二氧化钛复合型催化剂制备及其微波辅助催化氧化甲苯性能

实验采用溶胶凝胶法和传统浸渍法制备了TiO2-分子筛复合载体及复合载体负载过渡金属与稀土元素催化剂,通过微波辅助催化氧化甲苯的性能实验考察其催化活性.结果表明,复合TiO2明显提高了载体结构的稳定性与耐温性,并使过渡金属铜(Cu)、锰(Mn)和稀土元素铈(Ce)等活性组分在催化剂表面的分散更均匀;在复合载体吸附、吸波性能与多相活性组分催化的共同作用下,Cu-Mn-Ce/TiO2-分子筛催化剂微波辅助催化氧化甲苯的完全燃烧温度仅为175℃,此时甲苯去除率可达99％;15 h的连续性实验表明,TiO2复合型催化剂具有良好的催化活性与稳定性.由催化剂表征分析结果可知,活性组分颗粒的均匀分布与铜、锰氧化物及铜锰尖晶石固溶物等活性相的存在促进了甲苯的催化氧化,锐钛矿型TiO2较高的电子迁移速率与催化剂孔径的增大均有助于甲苯的氧化降解.     

Pd／Ce02-A1203对烟气中多环芳烃的催化氧化性能研究

采用浸渍法制备了不同负载量及不同钯铈比（Pd：Ce）的Pd/CeO2-Al2O3催化剂,并结合XRD、BET、SEM、O2-TPD和H2-TPR等方法对催化剂的性质进行了表征,研究了所制备的催化剂对燃煤烟气中多环芳烃（PAHs）的催化转化效率.XRD和SEM结果表明,Ce和Pd在Al2O3表面呈高度分散状态,有利于PAHs的催化氧化.BET测试表明,Ce的引入改变了催化剂表面孔径结构,提高其比表面积.O2-TPD和H2-TPR测试表明,适当钯铈比条件下制备的催化剂有较强的储氧能力和活性.催化氧化实验结果表明,所制备的Pd/CeO2-Al2O3催化剂对PAHs具有较高的转化效率,其平均转化率均在80%以上,且PAHs的毒性当量显著降低,钯铈比对PAHs的催化氧化性能影响较大,当催化剂的钯铈比为1：1时,PAHs的转化率最高,可达90%以上.     

Pd/CeO2-Al2O3对烟气中多环芳烃的催化氧化性能研究

采用浸渍法制备了不同负载量及不同钯铈比(Pd:Ce)的Pd/CeO2-Al2O3催化剂,并结合XRD、BET、SEM、O2-TPD和H2-TPR等方法对催化剂的性质进行了表征,研究了所制备的催化剂对燃煤烟气中多环芳烃(PAHs)的催化转化效率.XRD和SEM结果表明,Ce和Pd在Al2O3表面呈高度分散状态,有利于PAHs的催化氧化.BET测试表明,Ce的引入改变了催化剂表面孔径结构,提高其比表面积.O2-TPD和H2-TPR测试表明,适当钯铈比条件下制备的催化剂有较强的储氧能力和活性.催化氧化实验结果表明,所制备的Pd/CeO2-Al2O3催化剂对PAHs具有较高的转化效率,其平均转化率均在80%以上,且PAHs的毒性当量显著降低,钯铈比对PAHs的催化氧化性能影响较大,当催化剂的钯铈比为1:1时,PAHs的转化率最高,可达90%以上.     

Complete catalytic oxidation of o-xylene over Ce02 nanocubes

The activities of CeO2 nanocubes calcined at different temperatures were tested for catalytic oxidation of o-xylene. Using CeO2 nanocubes as catalysts, complete catalytic oxidation of o-xylene was achieved below 210℃. The CeO2 nanomaterials were characterized by means of BET, X-ray diffraction (XRD), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). From the TEM images, all Ce02 nanocubes displayed cubic morphology irrespective of calcination temperature. The HRTEM images revealed that these nanocubes were enclosed by reactive {001}planes, which may contribute to the intrinsically catalytic property of o-xylene oxidation. The higher activity of Ce02 nanocubes calcined at 550℃ than those calcined at above 550℃ was attributed to their smaller crystallite size and larger surface area. The influences of reaction conditions were also studied, which found that a higher reaction temperature was necessary for complete catalytic oxidation of o-xylene at higher weight hourly space velocity (WHSV) and o-xylene concentration.     

Complete catalytic oxidation of o-xylene over CeO2 nanocubes

The activities of CeO2 nanocubes calcined at di erent temperatures were tested for catalytic oxidation of o-xylene. Using CeO2 nanocubes as catalysts, complete catalytic oxidation of o-xylene was achieved below 210°C. The CeO2 nanomaterials were characterized by means of BET, X-ray di raction (XRD), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). From the TEM images, all CeO2 nanocubes displayed cubic morphology irrespective of calcination temperature. The HRTEM images revealed that these nanocubes were enclosed by reactive f001g planes, which may contribute to the intrinsically catalytic property of o-xylene oxidation. The higher activity of CeO2 nanocubes calcined at 550°C than those calcined at above 550°C was attributed to their smaller crystallite size and larger surface area. The influences of reaction conditions were also studied, which found that a higher reaction temperature was necessary for complete catalytic oxidation of o-xylene at higher weight hourly space velocity (WHSV) and o-xylene concentration.     

Size effect of Pt nanoparticles in acid-assisted soot oxidation in the presence of NO

Pt/Al₂O₃ catalysts with mean Pt particle size ranged from 2.7 to 7.1 nm were synthesized by chemical reduction method, and the sulfated counterparts were prepared by impregnation of sulfuric acid. The turnover frequency of platinum for soot oxidation under loose contact conditions in a feed flow containing NO and O₂ are positively correlated with the size of platinum. The sulfated Pt/Al₂O₃ exhibits higher catalytic activity for soot oxidation in the presence of NO despite their reduced ability for NO₂ production. Such a contradiction is more significant for those catalysts with smaller platinum particles. Herein, the catalysts were characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), transmission electron microscopy (TEM), inductive coupled plasma (ICP) emission spectrometry, CO chemisorption, thermogravimetric analysis (TGA), NH₃ temperature-programmed desorption (NH₃-TPD), NO temperature-programmed oxidation (TPO) and NO_x temperature-programmed desorption (TPD). Possible effect of Pt particle size for the catalytic oxidation of soot in the presence of NO was presented based primarily on the promoted NO₂ transfer efficiency onto the soot pushed by the acidic catalysts.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

Preparation of birnessite-supported Pt nanoparticles and their application in catalytic oxidation of formaldehyde

Flaky and nanospherical birnessite and birnessite-supported Pt catalysts were successfully prepared and characterized by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS) and N₂ adsorption-desorption. Effects of the birnessite morphology and Pt reduction method on the catalytic activity for the complete oxidation of formaldehyde (HCHO) were investigated. It was found that flaky birnessite exhibited higher catalytic activity than nanospherical birnessite. The promoting effect of Pt on the birnessite catalyst indicated that the reduction method of the Pt precursor greatly influenced the catalytic performance. Flaky birnessite-supported Pt nanoparticles reduced by KBH₄ showed the highest catalytic activity and could completely oxidize HCHO into CO₂ and H₂O at 50℃, whereas the sample reduced using H₂-plasma showed lower activity for HCHO oxidation. The differences in catalytic activity of these materials were jointly attributed to the effects of pore structure, surface active sites exposed to HCHO and the dispersion of Pt nanoparticles.     

低温等离子体结合锰基催化剂去除乙酸乙酯的研究

利用固态法和溶胶-凝胶法分别制备了钙钛矿（LaMnO₃）和八面体分子筛（OMS）两种锰基催化剂,在不同工况（输入电压、初始浓度、停留时间和催化剂放置量）条件下考察了等离子体催化对乙酸乙酯的降解特性.结果发现,锰基催化剂的加入显著提高了乙酸乙酯的去除率,减少了副产物的生成,并且OMS的催化活性高于LaMnO₃;此外,乙酸乙酯去除率随着电压的升高而增加,随着污染物初始浓度的增大而减少,并随停留时间的增长而变大;催化剂放置量为0.2 g时催化效果最佳.OMS催化剂在等离子体催化长期运行过程中表现出较好的稳定性.基于X射线衍射（XRD）、X射线光电子能谱（XPS）、H₂程序升温还原（H₂-TPR）、比表面积测试（BET）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）等手段对锰基催化剂物理化学性质的分析表明,OMS具有较高的催化活性主要归功于其拥有更高比例的Mn⁴⁺/（Mn³⁺+Mn⁴⁺）和吸附氧（O_ads）/晶格氧（O_latt）.     

Promoting effect of vanadium on catalytic activity of Pt/Ce–Zr–O diesel oxidation catalysts

A series of Pt–V/Ce–Zr–O diesel oxidation catalysts was prepared using the impregnation method. The catalytic activity and sulfur resistance of Pt–V/Ce–Zr–O were investigated in the presence of simulated diesel exhaust. The effect of vanadium on the structure and redox properties of the catalysts was also investigated using the Brunauer–Emmett–Teller method,X-ray diffraction, H2temperature-programmed reduction, CO temperature-programmed desorption, X-ray photoelectron spectroscopy, and Energy Dispersive Spectroscopy. Results showed that the Pt particles were well dispersed on the Ce–Zr–O carrier through the vanadium isolation effect, which significantly improved the oxidation activity toward CO and hydrocarbons. An electron-withdrawing phenomenon occurred from V to Pt, resulting in an increase in the metallic nature of platinum, which was beneficial to hydrocarbon molecular activation.     

Nano-sized alumina supported palladium catalysts for methane combustion with excellent thermal stability

Pd/Al₂O₃ catalysts supported on Al₂O₃ of different particle sizes were synthesized and applied in methane combustion. These catalysts were systematically characterized by Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), high resolution-transmission electron microscopy (HR-TEM), high-angle annular dark field-scanning transmission electron microscopy (HAADF-STEM), H₂-temperature-programmed reduction (H₂-TPR), O₂-temperature-programmed oxidation (O₂-TPO), X-ray photoelectron spectroscopy (XPS), and X-ray absorption fine structure (XAFS). The characterization results indicated that nano-sized Al₂O₃ enabled the uniform dispersion of palladium nanoparticles, thus contributing to the excellent catalytic performance of these nano-sized Pd/Al₂O₃ catalysts. Among them, Pd/Al₂O₃-nano-10 (Pd/Al₂O₃ supported by alumina with an average particle size of 10 nm) showed superior catalytic activity and stability for methane oxidation under harsh practical conditions. It maintained excellent catalytic performance for methane oxidation for 50 hr and remained stable even after harsh hydrothermal aging in 10 vol.% steam at 800°C for 16 hr. Characterization results revealed that the strong metal-support interactions and physical barriers provided by Al₂O₃-nano-10 suppressed the coalescence ripening of palladium species, and thus contributed to the superior sintering resistance of the Pd/Al₂O₃-nano-10 catalyst.