Role of surface functionality in the adsorption of anionic dyes on modified polymeric sorbents

While synthetic polymeric sorbents effectively treat dye wastewaters by adsorption, the underlying mechanisms remain to be understood. This work determined the adsorption of an anionic dye by three polymers differing significantly in surface functionality. Surface functional groups of polymers were indicated in FTIR spectra and quantified by the Boehm titration. In reference to the commercial sorbent XAD-4 with a low degree of functionality, the laboratory synthesized NG-8 had primarily acidic functional groups, whereas its aminated product MN-8 had mainly basic amino groups. Electrophoresis determined the points of zero charge of 4.18, 3.23, and 4.51 for XAD-4, NG-8, and MN-8, respectively. The adsorption of Reactive Black 5 dye (RB5) by all the sorbents on a unit surface area basis increased with decreasing pH. At the same low pH (4.40), the adsorption by NG-8 was similar to that by XAD-4, indicating little influence of protonated (neutral) surface functional groups. In contrast, the adsorption by NG-8 at pH 6.05 was 75% lower than that by XAD-4, resulting apparently from the strong electrostatic repulsion between RB5 and deprotonated (negative) groups. Amination substantially enhanced RB5 adsorption by eliminating acidic groups and creating a positive charge on the surface of MN-8. The adsorptive enhancement was also achieved in the presence of CaCl2, due presumably to the neutralization of negative surface charge by Ca2+ and the RB5-Ca2+ pairing. These results manifest the important role of surface functionality in the adsorption of dyes by synthetic polymers.     

Immobilized humic substances as sorbents

A new method was developed for the immobilization of humic substances. Humic acids (HA) immobilized onto different carriers were studied as sorbents for organic and inorganic substances. The sorption isotherms of 4-aminoazobenzene, Crystal Violet, Methylene Green, and flavine mononucleotide on immobilized HA show that pH and salt concentration have a significant effect on the sorption process, largely depending on the properties of polymeric matrix. Humic acids from different sources showed differing sorption capacity for the studied groups of substances.     

Valorization of spent coffee grounds recycling as a potential alternative fuel resource in Turkey: An experimental study

In this study, recycling of spent coffee grounds (SCG) as a potential feedstock for alternative fuel production and compounds of added value in Turkey was assessed. The average oil content was found (≈ 13% w/w). All samples (before and after extraction) were tested for scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), X-ray diffraction (XRD), calorific value, surface analysis and porosity, Fourier transform infrared (FT-IR), and elemental analysis to assess their potential towards fuel properties. Elemental analysis indicated that carbon represents the highest percentages (49.59% and 46.42%, respectively), followed by nitrogen (16.7% and 15.5%), hydrogen (6.74% and 6.04%), and sulfur (0.851% and 0.561%). These results indicate that SCG can be utilized as compost, as it is rich in nitrogen. Properties of the extracted oil were examined, followed by biodiesel production. The quality of biodiesel was compared with American Society for Testing and Materials (ASTM) D6751 standards, and all the properties complied with standard specifications. The fatty acid compositions were analyzed by gas chromatography. It was observed that coffee waste methyl ester (CWME) is mainly composed of palmitic (35.8%) and arachidic (44.6%) acids, which are saturated fatty acids. The low degree of unsaturation provides an excellent oxidation stability (10.4 hr). CWME has also excellent cetane number, higher heating value, and iodine value with poor cold flow properties. The studies also investigated blending of biodiesel with Euro diesel and butanol. Following this, a remarkable improvement in cloud and pour points of biodiesel was obtained. Spent coffee grounds after oil extraction is an ideal material for garden fertilizer, feedstock for ethanol, biogas production, and as fuel pellets. The outcome of such research work produces valuable insights on the recycling importance of SCG in Turkey.

Implications: Coffee is a huge industry, and coffee has been widely used due to its refreshing properties. This industry generates large quantities of waste. Therefore, recycling of spent coffee grounds for producing alternative fuels and compounds of added value is crucial. Elemental analysis indicated that coffee waste can be utilized as compost, as it is rich in nitrogen. Coffee waste after oil extraction is an ideal feedstock for ethanol and biogas production, garden fertilizer, and as fuel pellets. The low degree of unsaturation provides excellent oxidation stability. Its biodiesel has also excellent cetane number, higher heating value, and lower iodine value.     

Use of biomass sorbents for oil removal from gas station runoff

The use of biomass sorbents, which are less expensive and more biodegradable than synthetic sorbents, for oil removal from gas station runoff was investigated. A bench-scale flume experiment was conducted to evaluate the oil removal and retention capabilities of the biomass sorbents which included kapok fiber, cattail fiber, Salvinia sp., wood chip, rice husk, coconut husk, and bagasse. Polyester fiber, a commercial synthetic sorbent, was also experimented for comparison purpose. Oil sorption and desorption tests were performed at a water flow rate of 20 lmin-1. In the oil sorption tests, a 50 mgl(-1) of used engine oil-water mixture was synthesized to simulate the gas station runoff. The mass of oil sorbed for all sorbents, except coconut husk and bagasse, was greater than 70%. Cattail fiber and polyester fiber were the sorbents that provided the least average effluent oil concentrations. Oil selectivity (hydrophobic properties) and physical characteristics of the sorbents are the two main factors that influence the oil sorption capability. The used sorbents from the sorption tests were employed in the desorption tests. Results indicated that oil leached out of all the sorbents tested. Polyester fiber released the highest amount of oil, approximately 4% (mass basis) of the oil sorbed.     

Using FTIR to corroborate the identity of functional groups involved in the binding of Cd and Cr to saltbush (Atriplex canescens) biomass

Fourier transform infrared (FTIR) studies were performed to confirm the chemical modification of saltbush (Atriplex canescens) biomass and to provide information about the identity and binding characteristics of the chemical groups responsible for the binding of Cd(II), Cr(III), and Cr(VI). In addition, studies were performed to determine the optimum time for the binding of the three ions by saltbush biomass, and to study the efficiency of HCl and sodium citrate as stripping agents. The metal quantification was performed using inductively coupled plasma optical emission spectroscopy (ICP-OES). The results showed that 10 min or less is enough to achieve the maximum metal binding, and that aqueous solutions of 0.1 mM HCl or sodium citrate were enough to strip more than 80% of the bound Cd. It was determined that more than 70% of the bound Cr(III) was stripped using 0.1 mM HCl. Chemical modification of carboxyl and ester groups on the biomass was performed. The FTIR results confirmed that the esterification of carboxyl groups and hydrolysis of ester groups in the native biomass had occurred. The direct effect of these modifications on the binding properties of the biomass provided strong evidence that the carboxyl functionality is the main group responsible for binding Cd and Cr(III). However, the IR data showed that for Cr(VI), a different type of functional group is involved.     

Simultaneous control of Hg0, SO2, and NOx by novel oxidized calcium-based sorbents

Efforts to develop multipollutant control strategies have demonstrated that adding certain oxidants to different classes of Ca-based sorbents leads to a significant improvement in elemental Hg vapor (Hg0), SO2, and NOx removal from simulated flue gases. In the study presented here, two classes of Ca-based sorbents (hydrated limes and silicate compounds) were investigated. A number of oxidizing additives at different concentrations were used in the Ca-based sorbent production process. The Hg0, SO2, and NOx capture capacities of these oxidant-enriched sorbents were evaluated and compared to those of a commercially available activated carbon in bench-scale, fixed-bed, and fluid-bed systems. Calcium-based sorbents prepared with two oxidants, designated C and M, exhibited Hg0 sorption capacities (approximately 100 microg/g) comparable to that of the activated carbon; they showed far superior SO2 and NOx sorption capacities. Preliminary cost estimates for the process utilizing these novel sorbents indicate potential for substantial lowering of control costs, as compared with other processes currently used or considered for control of Hg0, SO2, and NOx emissions from coal-fired boilers. The implications of these findings toward development of multipollutant control technologies and planned pilot and field evaluations of more promising multipollutant sorbents are summarily discussed.     

Relevant parameters for assessing the environmental impact of some pyridinium, ammonium and pyrrolidinium based ionic liquids

Several physico-chemical properties relevant to determine the environmental impact of ionic liquids - aqueous solubility, octanol/water partition coefficient, chromatographically derived lipophilicity and infinite dilution diffusion coefficients in water - were measured in ionic liquids based on pyridinium, ammonium and pyrrolidinium cations with bis(trifluoromethylsulfonyl)imide anions. The influence of the presence of hydroxyl or ester groups in the physico-chemical properties of these liquids was checked. It appeared that the presence of functional oxygenated moieties reduces the lipophilicity of ionic liquids and so decreases the risk of bioaccumulation in environment.     

Pore structure effects on Ca-based sorbent sulfation capacity at medium temperatures: activated carbon as sorbent/catalyst support

The reaction between three different Ca-based sorbents and SO2 were studied in a medium temperature range (473-773 K). The largest SO2 capture was found with Ca(OH)2 at 773 K, 126.31 mg SO2 x g Ca(OH)2(-1), and the influence of SO2 concentration on the sorbent utilization was observed. Investigations of the internal porous structure of Ca-based sorbents showed that the initial reaction rate was controlled by the surface area, and once the sulfated products were produced, pore structure dominated. To increase the surface area of Ca-based sorbents available to interact with and retain SO2, one kind of CaO/ activated carbon (AC) sorbent/catalyst was prepared to study the effect of AC on the dispersion of Ca-based materials. The results indicated that the Ca-based material dispersed on high-surface-area AC had more capacities for SO2 than unsupported Ca-based sorbents. The initial reaction rates of the reaction between SO2 and Ca-based sorbents and the prepared CaO/AC sorbents/catalysts were measured. Results showed that the reaction rate apparently increased with the presence of AC. It was concluded that CaO/AC was the active material in the desulfurization reaction. AC acting as the support can play a role to supply O2 to increase the affinity to SO2. Moreover, when AC is acting as a support, the surface oxygen functional group formed on the surface of AC can serve as a new site for SO2 adsorption.     

Charge characteristics of humic and fulvic acids: comparative analysis by colloid titration and potentiometric titration with continuous pK-distribution function model

Charge characteristics of humic and fulvic acids of a different origin (inshore soils, peat, marine sediments, and soil (lysimetric) waters) were evaluated by means of two alternative methods - colloid titration and potentiometric titration. In order to elucidate possible limitations of the colloid titration as an express method of analysis of low content of humic substances we monitored changes in acid-base properties and charge densities of humic substances with soil depth, fractionation, and origin. We have shown that both factors - strength of acidic groups and molecular weight distribution in humic and fulvic acids - can affect the reliability of colloid titration. Due to deviations from 1:1 stoichiometry in interactions of humic substances with polymeric cationic titrant, the colloid titration can underestimate total acidity (charge density) of humic substances with domination of weak acidic functional groups (pK>6) and high content of the fractions with molecular weight below 1kDa.     

Modifying sorbents in controlled release formulations to prevent herbicides pollution

The herbicides chloridazon and metribuzin, identified as groundwater pollutants, were incorporated in alginate-based granules to obtain controlled release properties. In this research the effect of incorporation of sorbents such as bentonite, anthracite and activated carbon in alginate basic formulation were not only studied on encapsulation efficiency but also on the release rate of herbicides which was studied using water release kinetic tests. In addition, sorption studies of herbicides with bentonite, anthracite and activated carbon were made. The kinetic experiments of chloridazon and metribuzin release in water have shown that the release rate is higher in metribuzin systems than in those prepared with chloridazon, which has lower water solubility. Besides, it can be deduced that the use of sorbents reduces the release rate of the chloridazon and metribuzin in comparison to the technical product and to the alginate formulation without sorbents. The highest decrease in release rate corresponds to the formulations prepared with activated carbon as a sorbent. The water uptake, permeability, and time taken for 50% of the active ingredient to be released into water, T(50), were calculated to compare the formulations. On the basis of a parameter of an empirical equation used to fit the herbicide release data, the release of chloridazon and metribuzin from the various formulations into water is controlled by a diffusion mechanism. Sorption capacity of the sorbents for chloridazon and metribuzin, ranging from 0.53mgkg(-1) for the metribuzin sorption on bentonite to 2.03x10(5)mgkg(-1) for the sorption of chloridazon on the activated carbon, was the most important factor modulating the herbicide release.     

The utilization of catalyst sorbent in scrubbing acid gases from incineration flue gas

Catalyst sorbents based on alumina-supported CuO, CeO2, and CuO-CeO2 were applied to a dry scrubber to clean up the SO2/HCl/NO simultaneously from pilot-scale fluidized-bed incineration flue gas. In the presence of organic compounds, CO and the submicron particles SO2 and HCI removed by the fresh catalyst sorbents and NO reduced to N2 by NH3 under the catalysis of fresh and spent desulfurization/dechloridization (DeSO2/DeHCl) catalyst sorbents (copper compounds, Cu, CuO, and CuSO4) were evaluated in this paper. The fresh and spent catalyst sorbents were characterized by the Brunner-Emmett-Teller method (BET), X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), inductively coupled plasma-mass spectrometry (ICP-MS), and the elemental analyzer (EA). The study showed that the performances of CuO, CeO2, and CuO-CeO2/gamma-Al2O3 were better than that of Ca(OH)2. The removal efficiency of SO2 and HCl was 80-95% in the dry scrubber system. Under NH3/NO = 1, NO could not be reduced to N2 because it was difficult to control the ratio of air/fuel in the flue gas. For estimating the feasibility of regenerating the spent catalyst sorbents, BET and EA analyses were used. They indicated that the pore structures were nearly maintained and a small amount of carbon accumulated on their surface.     

Chromate reduction on humic acid derived from a peat soil--exploration of the activated sites on HAs for chromate removal

Humic substances are a major component of soil organic matter that influence the behavior and fate of heavy metals such as Cr(VI), a toxic and carcinogenic element. In the study, a repetitive extraction technique was used to fractionate humic acids (HAs) from a peat soil into three fractions (denoted as F1, F2, and F3), and the relative importance of O-containing aromatic and aliphatic domains in humic substances for scavenging Cr(VI) was addressed at pH 1. Spectroscopic analyses indicated that the concentrations of aromatic C and O-containing functional groups decreased with a progressive extraction as follows: F1>F2>F3. Cr(VI) removal by HA proceeded slowly, but it was enhanced when light was applied due to the production of efficient reductants, such as superoxide radical and H(2)O(2), for Cr(VI). Higher aromatic- and O-containing F1 fraction exhibited a greater efficiency for Cr(VI) reduction (with a removal rate of ca. 2.89 mmol g(-1) HA under illumination for 3 h). (13)C NMR and FTIR spectra further demonstrated that the carboxyl groups were primarily responsible for Cr(VI) reduction. This study implied the mobility and fate of Cr(VI) would be greatly inhibited in the environments containing such organic groups.     

Evaluation of polyurethane foam as a trapping medium for herbicide vapor in air monitoring and worker inhalation studies

Polyurethane foam was an efficient adsorbent for trapping vapors of butyl esters of 2,4-D (2,4-dichlorophenoxyacetic acid) and triallate (S-(2,3,3-trichloroallyl)diisopropylthiocarbamate) in high volume air monitoring studies and of butyl esters of 2,4-D, iso-octyl ester of 2,4-D, n-butyl ester of 2,4,5-T (2,4,5-trichlorophenoxyacetic acid), bromoxynil octanoate (2,5-dibromo-4-hydroxybenzonitrile), triallate, and trifluralin (alpha, alpha, alpha-trifluoro-2,6-dinitro-N-N-dipropyl-p-toluidine) in short-term, low volume, worker inhalation exposure studies. The collected herbicide vapor was readily desorbed under soxhlet extraction with n-hexane and subsequently analyzed with electron-capture GLC. The overall efficiencies, for both trapping and extraction, were over 90%, using a single plug, for all herbicides, except triallate. In the case of triallate, two plugs in series were required for efficient trapping under the high volume air monitoring situation.     

聚环氧琥珀酸萃取锰泥残渣中铬的研究

聚环氧琥珀酸(PESA)是一种具有无磷及非氮结构、环境友好型水溶性聚合物,且具有螯合多价金属阳离子的性能和可生物降解性的特征,选取其作为锰泥残渣中铬的螯合萃取剂,研究了不同pH、螯合萃取剂剂量、搅拌时间下PESA对铬的萃取率。结果表明:(1)最佳萃取条件为pH=4、PESA剂量30mg/g、搅拌时间60min;在最佳萃取条件下,铬的萃取率可达95%。(2)从结构上看,PESA是由醚基和羧基基团组成的高分子聚合物,羧基基团是与金属离子作用的主要官能团,它对Ca2+、Mg2+、Zn2+、Cr(Ⅲ)、Cr(Ⅵ)和Pb2+等有较强的螯合能力;从溶液的配位角度看,PESA与金属有较强的结合能力。因此,PESA对锰泥残渣中的铬有萃取作用。     

Comparison of different modifications on QuEChERS sample preparation method for PAHs determination in black, green, red and white tea

The aim of this work was the evaluation of QuEChERS extraction method for polycyclic aromatic hydrocarbon (PAH) determination in various types of tea. In the experiment, different kinds of extraction solvents, sorbents and a final method of sample preparation were compared. The final extracts were analysed by gas chromatography-selected ion monitoring-mass spectrometry. The results suggest that acetonitrile extraction, clean up with SAX and final liquid–liquid extraction was the best combination giving the most purified extracts and acceptable compound recoveries for different types of teas. In the study of real samples, compounds belonging to light PAHs were mostly detected, and heavy polycyclic aromatic hydrocarbons, including benzo[a]pyrene, were not identified in any of samples.     

Preparation and characterization of activated carbons from tobacco stem by chemical activation

Activated carbons were prepared from tobacco stem by chemical activation using potassium hydroxide (KOH), potassium carbonate (K₂CO₃), and zinc chloride (ZnCl₂). The effects of the impregnation ratio (activating agent/precursor) and activating agents on the physical and chemical properties of activated carbons were investigated. The textual structure and surface properties of activated carbons were characterized by nitrogen (N₂) adsorption isotherm, scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FT-IR), x-ray photoelectron spectroscopy (XPS), and thermogravimetry (TG). ZnCl₂, acting as a superior activating agent compared to the others, produced much more porosity. The maximum specific surface area reached 1347 m²/g, obtained by ZnCl₂ activation with an impregnation ratio of 4.0. Moreover, ZnCl₂ activation yielded products with an excellent thermostability, attributed to different activation mechanisms. Various oxygen functions were detected on the activated carbon surface, and hydroxyl and ester groups were found to be in the majority.

Implications: Tobacco stem, the residue from cigarette manufacturing, is usually discarded as waste, leading to serious resource waste and environmental problems. This study provides an effective utilization available for this solid residue by using it as the starting material in the preparation of activated carbon with chemical activation. Activated carbons with high specific area and various surface functions have been prepared, and the effects of the amount and type of activating agents on the physical and chemical properties of activated carbon were investigated as well.     

Combined application of non-discriminated conventional pyrolysis and tetramethylammonium hydroxide-induced thermochemolysis for the characterization of the molecular structure of humic acid isolated from polluted sediments from the Ravenna Lagoon

Humic acid (HA) isolated from highly polluted sediment from the Ravenna Lagoon (Italy) was subjected to pyrolysis/tetramethylammonium hydroxide (TMAH)-induced thermochemolysis to reveal the impact of industrial activities on humification. Special effort was made to distinguish between analytes originating from the polymeric humic organic matter network along with sequestered compounds (which cannot be released by solvent extraction), and the solvent-extractable lipid fraction sorbed onto the organic matrix. Exhaustive solvent extraction of the isolated HA proved mandatory to avoid biased results when identifying the origin of the pyrolyzates of untreated samples. Conventional pyrolysis at 750 degrees C of the "degreased" HA revealed a characteristic polycyclic aromatic hydrocarbon (PAH) pattern, which was significantly different than patterns obtained from the pyrolysis of natural humic acids. TMAH-induced thermochemolysis at 500 degrees C provided information on carboxylic acids covalently bound inside the HA network via ester bonds. Thermochemolysis of the "degreased" matrix at 750 degrees C, resulting in the cleavage of C-O and C-C bonds, revealed a significant PAH pattern very similar to that obtained by conventional pyrolysis. The uncommon PAH pattern points to the formation of bound residues as the humification/detoxification pathway. Recalcitrant hopane hydrocarbons showed very similar patterns for both the untreated and exhaustively solvent-extracted samples, which points to hopanes being linked inside the humic network via C-C bonds. The technique of non-discriminating flash pyrolysis used in this study, based on extremely rapid capacitive discharge heating in a Silcosteel capillary, proved to be an excellent method to obtain high-boiling pyrolyzates (PAHs beyond 252Da molecular weight, C(29)-C(31)-hopanes).     

Experimental design methodology for the preparation of carbonaceous sorbents from sewage sludge by chemical activation--application to air and water treatments

The objective of this study is to optimize experimental conditions of sorbent preparation from sewage sludge using experimental design methodology. Series of carbonaceous sorbents have been prepared by chemical activation with sulfuric acid. The sorbents produced were characterized, and their properties (surface chemistry, porous and adsorptive properties) were analyzed as a function of the experimental conditions (impregnation ratio, activation temperature and time). Carbonaceous sorbents developed from sludge allow copper ion, phenol and dyes (Acid Red 18 and Basic Violet 4) to be removed from aqueous solution as well as VOC from gas phase. Indeed, according to experimental conditions, copper adsorption capacity varies from 77 to 83 mg g(-1), phenol adsorption capacity varies between 41 and 53 mg g(-1) and VOC adsorption capacities (acetone and toluene) range from 12 to 54 mg g(-1). Each response has been described by a second-order model that was found to be appropriate to predict most of the responses in every experimental region. The most influential factors on each experimental design response have been identified. Regions in which optimum values of each factor were achieved for preparation of activated carbons suitable for use in wastewater and gas treatments have been determined using response surfaces methodology. In order to have a high mass yield and to minimize the energetic cost of the process, the following optimal conditions, 1.5 g of H2SO4 g(-1) of sludge, 700 degrees C and 145 min are more appropriate for use of activated carbon from sludge in water and gas treatments.     

活性污泥胞外聚合物提取方法优化

试验对比了不同离子交换树脂(CER)含量和pH条件下胞外聚合物(EPS)的提取效果差异。结果表明,EPS各组分提取浓度均随离子交换树脂用量增加而增加,但各组分趋势不同。TOC的最佳树脂剂量为100 g CER/g VSS,而蛋白质、多糖和DNA的最佳树脂剂量约为70 g CER/g VSS。pH值对TOC、DNA和多糖的提取浓度影响较小,但对蛋白质影响比较大。各提取条件下,EPS各组分提取浓度随时间的变化过程可以分为平稳增长期、快速增长期及稳定期。     

Performance of Copper Chloride-Impregnated Sorbents on Mercury Vapor Control in an Entrained-Flow Reactor System

Abstract

An entrained-flow system has been designed and constructed to simulate in-flight mercury (Hg) capture by sorbent injection in ducts of coal-fired utility plants. The test conditions of 1.2-sec residence time, 140 °C gas temperature, 6.7 m/sec (22 ft/sec) gas velocity, and 0–0.24 g/m³ (0–15 lbs of sorbent per 1 million actual cubic feet of flue gas [lb/MMacf]) sorbent injection rates were chosen to simulate conditions in the ducts. Four kinds of sorbents were used in this study. Darco Hg-LH served as a benchmark sorbent with which Hg control capability of other sorbents could be compared. Also, Darco-FGD was used as a representative raw activated carbon sorbent. Two different copper chloride-impregnated sorbents were developed in our laboratory and tested in the entrained-flow system to examine the possibility of using these sorbents at coal-fired power plants. The test results showed that one of the copper chloride sorbents has remarkable elemental mercury (Hg⁰) oxidation capability, and the other sorbent demonstrated a better performance in Hg removal than Darco Hg-LH.