还原剂对Ag/Al2O3催化剂上NO还原的影响

在富氧条件下,研究了CH4、C3H8、C 3H6、C8H18、CH 3OH、C2H5OH,以及C3H6与CH3OH、C3H6与C2H5OH组合作还原剂时,在Ag/Al2O3催化剂上NO的还原活性.结果表明,不同碳氢化合物还原NO的活性温度存在较大的差异.SO2的存在会导致CH3OH还原NO的活性提高,而其他碳氢化合物还原NO的活性降低.随着还原剂浓度提高,NOx转化率增大,不过,过高的还原剂浓度对NO还原不利.组合使用CH3OH与C3H6或C2H5OH与C3H6作为还原剂,能显著拓宽活性温度范围.     

Catalytic destruction of 1,2-dichlorobenzene on V2O5-WO3/Al2O3-TiO2 catalyst

Studies on the catalytic destruction of 1,2-dichlorobenzene were carried out on a specially constructed semi-technical equipment whose most important element was a catalytic reactor with a monolithic catalyst in the form of 150 x 150 x 100 mm cubes. A catalyst made from cordierite with an active layer composed of Al2O3 - 64 wt%, TiO2 - 26 wt%, V2O5 - 6.6 wt% and WO3 - 3.4 wt% was used. The reactor made it possible to carry out the process in the temperature range 150-350 degrees C, at variable catalyst loading and different velocities of gas flow through the reactor. The content of 1,2-dichlorobenzene in the air was analysed by a chromatographic method. A significant effect of catalyst loading and temperature on 1,2-dichlorobenzene destruction efficiency was observed and no effect of the linear flow velocity through the catalyst on o-dichlorobenzene destruction efficiency was reported. The applied vanadium-tungsten catalyst on a monolithic carrier made from TiO2/gamma-Al2O3 revealed very good activity that resulted in an over 80% efficiency of 1,2-dichlorobenzene destruction at the temperature around 250 degrees C at a very high catalyst loading reaching ca. 8200 h(-1). Additionally, in this study the kinetics of 1,2-dichlorobenzene decomposition was determined, specifying the order of reaction and dependence of the decomposition rate constant on temperature, using a simple power-rate law model.     

铈改性Al2O3担载Pd催化剂的CO氧化性能研究

浸渍法制备了Al2O3＋CeO2为载体的Pd催化剂,对制备中各因素对催化剂效果的影响作了初步研究。考察了活性组分含量与催化剂性能的关系以及焙烧温度、水蒸气对催化剂活性的影响。结果表明,稀土Ce元素的存在使催化剂的性能得到明显改善。制备过程中焙烧步骤对催化剂的活性影响很大,催化剂制备必须高于600℃焙烧。     

中试规模下蜂窝式Mn-Ce/Al2O3脱硝催化剂的低温性能

采用自行设计的反应装置,研究中试规模条件下关键参数对蜂窝堇青石Mn-Ce/Al2O3催化剂脱硝效率的影响以及抗硫抗水性能,并通过扫描电子显微镜（SEM）、能谱仪（EDS）、X射线衍射（XRD）和比表面积测试仪（BET）研究催化剂的理化性质。结果表明,反应温度、空速、氨氮比对催化活性均有明显影响,同时,催化剂对氮氧化物浓度有较强适应性,NO浓度在134~469 mg·m-3区间内脱硝效率均可保持在75%以上。催化剂在100 oC,空速3 336 h-1,[NH3]/[NO]为0.9,烟气量20 m3·h-1条件下连续反应168 h,其催化效率可以稳定保持在75%~80%,说明蜂窝式Mn-Ce/Al2O3具有良好的稳定性。催化剂在含5%H2O气氛中催化效率由80%减少至60%,在去除H2O后抑制作用消失。反应气中通入143 mg·m-3 SO2后催化效率由80%降低至62%,停止通入SO2后活性不能恢复。同时通入143 mg·m-3 SO2和5%H2O,催化效率下降并维持在53%左右,停止通入后活性恢复至67%。通过对SO2中毒前后的催化剂表征分析可得,SO2存在条件下生成的硫酸铵盐堵塞了20 nm孔径以下的部分孔道,覆盖了催化剂表面活性位点,是引起效率下降的主要原因。     

前驱体对Cu/Al2O3的HCN催化水解性能的影响

为了研究前驱体因素对Cu/Al2O3的HCN催化水解性能的影响,考察了铜盐前驱体种类和前驱体溶液浓度对催化剂脱除HCN的规律变化,并探究了焙烧温度和反应温度对催化水解HCN的影响。采用浸渍法制备了Cu/Al2O3催化剂,并采用BET、SEM、XRD和XPS等对催化剂进行了表征。实验结果表明,以乙酸铜为前驱体制备的催化剂因具有较好的孔结构和较多的CuO负载量,使其相较其他3种铜盐表现出了最好的催化活性。当乙酸铜前驱体溶液浓度为0.050 mol·L-1,焙烧温度为400℃时,催化剂的催化活性最高。反应温度越高,越有利于提升催化活性。反应温度为250℃时,催化剂对HCN的脱除效率即达到96%以上。可见,以乙酸铜为前驱体制备的催化剂用于低温催化水解HCN效果理想,具有较好的应用前景。     

The kinetic of the catalytic decomposition of methyl isobutyl ketone over a Pt/gamma-Al2O3 catalyst

Environmental catalysis also can refer to catalytic technologies for reducing emission of environmentally unacceptable compounds. Catalytic decomposition also is one of the cost-effective technologies to solve the troublesome volatile organic compounds. This study treated methyl isobutyl ketone (MIBK) by a commercial catalyst, Pt/gamma-Al(2)O(3), in an isothermal fixed bed differential reactor. The effects of O(2) and MIBK content in carrier gas on the catalysis's reaction rate are also observed. Three kinetic models, i.e. the Mars and van Krevelen model, Langmuir-Hinshelwood model and power-rate law were applied to best fit the experimental results. The results indicate that the kinetic behavior of MIBK oxidation with catalysis can be accounted for by using the rate expression of the Mars and van Krevelen model and Langmuir-Hinshelwood model. Kinetic parameters are also determined on the basis of the differential reactor data. The experimental results are compared with those of the model predicted.     

H2O和SO2对V2O5-WO3/TiO2催化剂催化氧化NO的影响

研究了在120℃的反应温度下,H2O和SO2对V2O5-WO3/TiO2催化剂选择性催化氧化（SCO）NO的影响。结果表明,在H2O和SO2存在的情况下催化剂失活很快,停止通入H2O和SO2后活性不能恢复,但在加热到250℃后催化活性基本恢复。FT-IR分析表明,催化剂表面形成了金属硝酸盐和Ti的硫酸盐,对催化活性有一定影响,但不影响催化剂在250℃下催化活性的恢复。SO2、H2O和NO的竞争吸附与SO2和NO2的铅室反应是影响催化剂活性的主要原因。     

Mo掺入CeO2/Al2O3选择性催化还原NO动力学研究

采用共混法制备不同系列Mo掺入催化剂（CeMoxOy/Al2O3）,研究了Mo掺入对CeO2/Al2O3选择性催化还原NO活性的优化,考察了内外扩散对脱硝性能的影响,并计算得出反应活化能,从动力学角度考察了Mo掺入对脱硝活性反应速率的影响。结果表明,Al/Ce/Mo元素摩尔比为5：1：0.15,空速为7 200 h-1,煅烧温度为550 ℃时,催化剂在250~425 ℃内脱出NOx效率均大于90%;催化剂平均粒径小于40目时,空速大于105 h-1时,内外扩散的影响可以忽略不计, CeMoxOy/Al2O3催化反应为一级反应,其中NH3和O2反应级数近似为0级。 CeMo0.15Oy/Al2O3活化能为36.57 kJ·mol-1,Mo的添加有效的减小了催化剂的表观反应活化能,增加了反应速率,提高了催化活性。     

催化剂Cu/HZSM-5的硅铝比对催化分解N2O的影响

为系统研究Cu/HZSM-5硅铝比对其各类性能的影响,采用等体积浸渍法与离子交换法,以硅铝比为27、50、117的HZSM-5为载体,制备负载型N_2O催化分解催化剂Cu/HZSM-5和Cu/ZSM-5,催化剂的活性组分为CuO。通过催化剂反应活性评价、X射线荧光光谱分析、X射线衍射分析结果,对2种方法制备催化剂活性的差异进行了分析。利用比表面积孔径分析仪(BET)、X射线衍射分析(XRD)、场发射扫描电镜(SEM)、X射线荧光光谱分析(XRF)、氢气程序升温还原分析(H_2-TPR)、氨气程序升温脱附分析(NH_3-TPD)等表征手段对催化剂物化性质等进行分析,得到载体HZSM-5的硅铝比差异对催化剂特征结构、比表面积、特征形貌、酸性位数量、可还原性能的影响规律。等体积浸渍法制备的催化剂活性评价结果表明,硅铝比为27的Cu_8/HZSM-5催化剂活性最好,完全催化分解N_2O的温度在400℃左右。水热稳定性实验结果以及寿命实验结果表明,硅铝比为27的Cu_8/HZSM-5具有良好的水热稳性,3种硅铝比的Cu_8/HZSM-5催化剂均具备良好的热稳定性。Cu/HZSM-5的活性评价以及各种表征结果显示,在一定范围内,硅铝比越低,催化剂活性越好。     

ZnO/Al_2O_3-SiO_2固体碱催化动物脂肪废油制备生物柴油

采用溶胶-凝胶法制备了Al_2O_3-Si O_2复合载体,采用等体积浸渍法在复合载体上负载Zn O制备固体碱催化剂,催化动物脂肪废油酯交换反应来制备生物柴油。研究了Zn O负载量以及复合载体中Al_2O_3/Si O_2质量比对催化剂活性的影响,并通过重复性实验对优化得到的催化剂稳定性进行考察。活性测试表明,当Zn O的负载量为20%,复合载体中Al_2O_3/Si O_2质量比为1∶9时催化剂的活性最佳,酯交换率达到95.2%。另外,对催化剂进行了BET、XRD、CO_2-TPD一系列表征。结果表明,Al_2O_3高度分散渗透于非晶相Si O_2中,形成催化剂的介孔结构。Zn O负载量为20%时催化剂碱性最强,这是导致催化剂高活性的重要原因。     

The catalytic incineration of styrene over an Mn2O3/Fe2O3 catalyst

In this study, styrene monomer (SM) was treated by a commercial catalyst, Mn2O3/Fe2O3, in a fixed-bed reactor. The study can be classified into two major parts. First, the effects of operating factors, such as temperature, SM concentration, space velocity, and O2 concentration, on the performance of the catalyst were investigated. Second, two catalyst life tests were carried out to characterize the deactivation effect of SM. The results show that the catalyst results in higher conversion of SM at a higher inlet temperature and higher O2 concentrations. The conversion of SM decreases with increasing SM concentration and space velocity. From the statistical analysis of the data, we find that temperature is the most important factor on the catalytic incineration. Oxygen concentration, SM concentration, and space velocity are significant parameters as well. This paper also provides information on the deactivation effect of SM. The catalysts were characterized by surface and pore-size analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), and electron spectroscopy for chemical analysis (ESCA) before and after the tests. The results show that the catalytic deactivation may be caused by carbon coating, and the pore size and surface area of the catalyst are smaller after deactivation.     

SiO2掺杂对V2O5-WO3/TiO2脱硝催化性能的影响

采用溶胶凝胶法制备TiO2-SiO2载体,浸渍法制备出V2O5-WO3/TiO2-SiO2催化剂,利用BET、FESEM、XRD、TGA和激光拉曼对催化剂进行表征,研究催化剂的理化性质。以NH3为还原剂,考察反应温度、SiO2掺杂量、焙烧温度、空速和使用时间对SCR催化还原NO的性能影响。结果表明,V2O5-WO3/TiO2-SiO2催化剂最佳反应温度在250~350℃。SiO2掺杂能提高活性组分V2O5和WO3在载体表面的分散性,制备出的催化剂具有更大的比表面积和更宽的温度区间,提高脱硝活性及稳定性。SiO2掺杂量对催化剂性能影响较大,制备的催化剂中,TiO2/SiO2=2显示了最大催化活性,脱硝率均在60%以上,TiO2/SiO2=0.5制备的催化剂稳定性最差。焙烧温度对催化剂性能也有影响,焙烧温度在500和600℃时,最低脱硝率为58%和23%,最佳焙烧温度为400℃,脱硝率均在80%以上,具有优越的脱硝性能。实验结果还表明,空速对V2O5-WO3/TiO2-SiO2催化剂的影响不大,在20 000 h-1空速下催化剂的使用时间对脱硝率的影响也不大,48 h内能保持在99%左右,非常稳定。     

Mn的氧化价态对Mn／γ-Al2O3催化剂催化臭氧氧化气相低浓度甲苯的影响

采用共沉淀法,以Al2O3为载体制备Mn／γ-Al2O3和Mn—Ce／Mn／γ-Al2O3催化剂,并分别在N2气氛和O2气氛下焙烧。采用固定床连续流动反应器,研究所制备催化剂在室温条件下催化臭氧氧化甲苯的性能。通过XRD、XPS和FTIR等手段对催化剂的结构和组成进行表征。结果表明,Mn／Mn／γ-Al2O3催化剂具有良好的催化臭氧氧化甲苯和催化臭氧自身分解的性能,共沉淀法制备催化剂的最佳Mn负载量为20％。O2气氛焙烧和Ce的加入,可以有效提高催化剂的活性和寿命。原因是O2气氛焙烧和Ce的加入可以提高Mn的氧化价态。催化剂失活的主要原因是有机副产物在催化剂表面吸附堆积,失活催化剂在550℃、空气气氛下焙烧可恢复催化性能。     

Fe/Ga2O3-Al2O3催化甲烷还原NO的性能

以甲烷为还原剂的选择性催化脱硝技术(SCR-CH_4)是一种很有潜力的新的脱硝方法,但催化剂的催化活性比较低。为了提高催化剂的活性以及抗水能力,可使用Fe对Al_2O_3负载的Ga_2O_3催化剂进行改性。采用共沉淀法,制备了xFe/Ga_2O_3-Al_2O_3催化剂,在固定床反应器中测试其选择性催化CH_4还原NO的性能。使用XRD、N_2吸附脱附、XPS、H_2-TPR、Py-IR等方法进行表征。结果表明:经过Fe改性后的催化剂提高了中高温的催化活性,提高了催化剂的N_2选择性,并改善了催化剂的抗水特性;5Fe/Ga_2O_3-Al_2O_3催化剂在500℃、富氧条件下,达到76%的NO转化率和100%的N_2选择性;在5%水蒸气条件下,5Fe/Ga_2O_3-Al_2O_3在500℃仍保持60%以上的NO转化率。N_2吸附脱附结果显示,引入Fe后,催化剂保持了原有比表面积,并且大大增加了催化剂孔径,可提高催化剂抗水能力。XPS与UV-vis显示,5Fe/Ga_2O_3-Al_2O_3具有高含量的游离态Fe~(3+),可提高催化剂的中高温活性。H2-TPR结果显示,Fe的引入提高了催化剂氧化还原能力,增强了原有Ga_2O_3-Al_2O_3中高温的还原活性。Py-FT-IR结果显示,催化剂表面同时存在Lewis酸和Br?nsted酸,铁的引入增加了催化剂表面的Lewis酸量。因此,Fe修饰Ga_2O_3-Al_2O_3是提高Ga_2O_3-Al_2O_3催化剂的SCR-CH_4脱硝性能的有效方法。     

Catalytic performance of Ag/Al2O3-C2H5OH-Cu/Al2O3 system for the removal of NOx from diesel engine exhaust

The selective catalytic reduction (SCR) of NOx by C(2)H(5)OH was studied in excess oxygen over Ag/Al(2)O(3) catalysts with different Ag loadings at lab conditions. The 4% Ag/Al(2)O(3) has the highest activity for the C(2)H(5)OH-SCR of NOx with a drawback of simultaneously producing CO and unburned THC in effluent gases. An oxidation catalyst 10% Cu/Al(2)O(3) was directly placed after the Ag/Al(2)O(3) to remove CO and unburned THC. Washcoated honeycomb catalysts were prepared based on the 4% Ag/Al(2)O(3) and 10% Cu/Al(2)O(3) powders and tested for the C(2)H(5)OH-SCR of NOx on a diesel engine at the practical operating conditions. Compared with the Ag/Al(2)O(3) powder, the Ag/Al(2)O(3) washcoated honeycomb catalyst (SCR catalyst) has a similar activity for NOx reduction by C(2)H(5)OH and the drawback of increasing the CO and unburned THC emissions. Using the SCR+Oxi composite catalyst with the optimization of C(2)H(5)OH addition, the diesel engine completely meets EURO III emission standards.     

Catalytic reduction of N2O over Ag-Pd/Al2O3 bimetallic catalysts

A study of the catalytic conversion of N2O to N2 over a bimetallic Ag-Pd catalyst is described in this article. Several Ag-Pd catalytic systems were prepared supported on Al2O3 with different ratios and their catalytic activity for the direct decomposition of N2O and their reduction with CO was measured. Based on the experimental results, it was observed that Ag-Pd bimetallic catalyst (5-0.5%) was the most active for both nitrous oxide reduction and direct decomposition. This high activity seems to be connected with a synergistic effect between Ag and Pd.     

Na-Ba/γ-Al2O3的NO和SO2吸附性能研究

研究了Na-Ba/γ-Al2O3吸附催化剂上NO和SO2的吸附-脱附性能.Na、Ba质量分数分别为6.2%、5.4%,焙烧温度和焙烧时间分别为600 ℃和10 h,吸附温度为100 ℃,其对NO、SO2的最大吸附量分别为0.052 4、0.344 mmol/g.同时考察了添加第三活性组份的影响,结果表明,Fe最为有效,Na-Ba/Fe/γ-Al2O3的NO、SO2最大吸附量分别为0.062 4、0.486 mmol/g.漫反射红外光谱研究结果表明,Fe降低了硫酸盐分解温度,促进吸附催化剂的再生.     

F掺杂改性及其制备方法优化对V2O5-WO3/TiO2催化剂低温SCR脱硝性能的影响

为提高SCR脱硝催化剂的低温脱硝性能,采用正交实验的方法制备了一系列氟（F）掺杂V2O5-WO3/TiO2催化剂,并对其进行活性分析,考察了不同氟元素来源（氟钛酸铵、氟化铵）、不同钒元素（V）前驱体（乙酰丙酮氧钒、偏钒酸铵）、钨元素（W）的不同添加方式（W做助剂、W既做载体又充当助剂）、不同载体制备方式（溶胶凝胶法、浸渍法）对催化剂脱硝性能的影响。结果表明,F掺杂改性显著增强了催化剂在200~350 ℃温度范围内的脱硝性能,其中以乙酰丙酮氧钒为V前驱体,以氟化铵为F源,W既充当载体又做助剂的方式制备出的F掺杂V2O5-WO3/TiO2催化剂具有最优的脱硝效果,其在空速为10 000 h-1的情况下,在200~350 ℃的温度反应区间,活性能稳定维持在98%以上。同时采用XPS、BET、TGA、SEM、XRD、Raman一系列表征手段对催化剂的理化性质进行了分析,表征结果表明F元素掺杂提高了活性组分在载体表面的分散度,同时促使了催化剂表面的电荷发生转移,增强了催化剂表面的氧化还原能力,促进了催化剂表面化学吸附氧的生成,增加了还原态V物种与还原态W物种的数量。     

钒基活化液增活V2O5-WO3-MoO3/TiO2催化剂的实验研究

基于催化剂在线增活工艺,以火电厂运行条件下的典型钒钛类失活催化剂为原料,采用单因素变量法展开了钒基活化液各成分对失活催化剂增活效果的研究,对活化液增活后的催化剂进行活性评价及SEM、BET、FT-IR和XRD等分析,考察增活前后NO转换率、催化剂表面形貌及结构的变化情况。研究结果表明,在实验条件下,随着4种活性成分含量的增加,催化剂增活后NO转换率均呈现先升高后降低的规律,NO转换率最高达99%,且增活后催化剂表面活性成分增加,Brnsted酸性位增多,比表面积增加,对烟气具有较强适应力。     

多孔TiO2为载体的V2O5-WO3脱硝催化剂制备和表征

以硫酸氧钛为钛源,氨水为沉淀剂,制备得到大比表面积(60m2/g)的锐钛矿TiO2载体.TiO2载体具有多孔结构,孔径集中在5～12nm,孔体积达到0.24cm3/g.以多孔TiO2为载体,采用浸渍法制备不同V2O5负载量的V2O5-WO3催化剂,利用拉曼(Raman)光谱、X射线衍射(XRD)对催化剂进行表征,并研究了不同V2O5负载量催化剂的脱硝活性,以及NO浓度和NH3/NO摩尔比对催化剂活性的影响.结果表明,V2O5在TiO2表面高度分散,当V2O5负载量在3%(质量分数)以下时,载体表面钒物种为单体钒,表现出最好的脱硝活性,在280～450℃内NO转化率均能达到90%以上.该催化剂对不同进口NO浓度有较强的适应能力.采用该催化剂的脱硝工艺,NH3/NO摩尔比宜保持在0.8～1.0.