PCE dissolution and simultaneous dechlorination by nanoscale zero-valent iron particles in a DNAPL source zone

While the capability of nanoscale zero-valent iron (NZVI) to dechlorinate organic compounds in aqueous solutions has been demonstrated, the ability of NZVI to remove dense non-aqueous phase liquid (DNAPL) from source zones under flow-through conditions similar to a field scale application has not yet been thoroughly investigated. To gain insight on simultaneous DNAPL dissolution and NZVI-mediated dechlorination reactions after direct placement of NZVI into a DNAPL source zone, a combined experimental and modeling study was performed. First, a DNAPL tetrachloroethene (PCE) source zone with emplaced NZVI was built inside a small custom-made flow cell and the effluent PCE and dechlorination byproducts were monitored over time. Second, a model for rate-limited DNAPL dissolution and NZVI-mediated dechlorination of PCE to its three main reaction byproducts with a possibility for partitioning of these byproducts back into the DNAPL was formulated. The coupled processes occurring in the flow cell were simulated and analyzed using a detailed three-dimensional numerical model. It was found that subsurface emplacement of NZVI did not markedly accelerate DNAPL dissolution or the DNAPL mass-depletion rate, when NZVI at a particle concentration of 10g/L was directly emplaced in the DNAPL source zone. To react with NZVI the DNAPL PCE must first dissolve into the groundwater and the rate of dissolution controls the longevity of the DNAPL source. The modeling study further indicated that faster reacting particles would decrease aqueous contaminant concentrations but there is a limit to how much the mass removal rate can be increased by increasing the dechlorination reaction rate. To ensure reduction of aqueous contaminant concentrations, remediation of DNAPL contaminants with NZVI should include emplacement in a capture zone down-gradient of the DNAPL source.     

Application of an empirical transport model to simulate retention of nanocrystalline titanium dioxide in sand columns

Nanocrystalline titanium dioxide was injected into sand columns to simulate subsurface injection for creation of a permeable treatment barrier. Past usage of this material as an ex situ pilot scale treatment filter has shown that it has a high adsorption capacity for a number of heavy metals and therefore would be a good candidate for injection technology. Three suspension concentrations (50, 75 and 100 mg l(-1)) were pumped through packed sand columns at different flow velocities (3.0, 6.8 and 14.1 cm min(-1)). Little to no particles was detected in the effluent. Most of the nanoparticles remained in the sand columns, with an increasing then decreasing retained solids pattern. Application of a one-dimensional advection-dispersion flow model, that included two empirical kinetic terms to account for particle retention in the porous media, produced data fits that followed the general trend of the data, but did not truly capture the concentration maxima in the data sets. Discussion of these results highlights the limited ability of existing models to aid in predicting particle retention of non-ideal materials for engineering purposes.     

Determining straining of Escherichia coli from breakthrough curves

Though coliform bacteria are used world wide as an indication of faecal pollution, the parameters determining the transport of Escherichia coli in aquifers are relatively unknown, especially for the period after the clean bed collision phase brought about by prolonged infiltration of waste water. In this research, the breakthrough curves of E. coli after total flushing of 50-200 pore volumes were studied for various influent concentrations in various sediments at different pore water flow velocities. The results indicated that straining in Dead End Pores (DEPs) was an important process that dominated bacteria breakthrough in fine-grained sediment (0.06-0.2 mm). The filling of the DEP space with bacteria took 5-65 pore volumes and was dependent on concentration. Column breakthrough curves were modelled and from this the DEP volumes were determined. These volumes (0.21-0.35% of total column volume) corresponded well with values calculated with a formula based on purely geometrical considerations and also with values calculated with a pore size density function. For this function the so-called Van Genuchten parameters of the sediments used in the experiments were determined. The results indicate that straining might be a dominant process affecting colloid transport in the natural environment and therefore it is concluded that proper knowledge of the pore size distribution is crucial to an understanding of the retention of bacteria.     

旋流场超细颗粒聚集实验研究

不同粒径分布和浓度的催化裂化(FCC)三旋回收超细催化剂颗粒在旋流场中经过50 h循环回流,颗粒中值粒径变化明显。物料中分散相越多、颗粒粒径越小时,颗粒碰撞越频繁,其聚集趋势越明显。颗粒聚集体在旋流场内不够稳定,通过对比不同进料速率下的旋流场聚集效果,得到最适合颗粒聚集的旋流场雷诺数为20 000。颗粒聚集体存在聚集极限粒径,其最佳聚集时间约为40 h,颗粒聚集后的旋流分离效率提高近5%。     

颗粒层中非水相液体污染物冲洗排出速度的数值模拟简

在进行污染土壤的冲洗修复时,模型模拟是极具优势的预测净化效果的方法。本研究分别采用5种粒径的球形玻璃微珠模拟实际土壤,实验考察了玻璃微珠颗粒层中水和非水相液体的排出速度,给出了颗粒层中液含率分布函数,以及最大和最小颗粒层孔隙直径的定义,建立了一个描述颗粒层中水和非水相液体排出速度的多孔介质孔隙毛细管束模型。使用构建的模型模拟水和异辛烷在颗粒层中的排出速度,模拟结果与实验数据有很好的一致性,模型预测结果的平均相对误差小于6.4%,特别是对粒径较小颗粒层,预测的准确性更高。模型可作为进一步研究在非水相液体饱和土壤水冲洗修复时,水和非水相液体排出速度和修复效果的基础。     

Optimization of circular plate separators with cross flow for removal of oil droplets and solid particles

A circular gravity-phase separator using coalescing medium with cross flow was developed to remove oil and suspended solids from wastewaters. Coalescence medium in the form of inclined plates promotes rising of oil droplets through coalescence and settling of solid particles through coagulation. It exhibits 22.67% higher removal of total suspended solids (TSS) compared to separators without coalescing medium. Moreover, it removed more than 70% of oil compared to conventional American Petroleum Institute separators, which exhibit an average of 33% oil removal. The flowrate required to attain an effluent oil concentration of 10 mg/L (Q(o10)) at different influent oil concentrations (C(io)) can be represented by Q(o10) x 10(-5) = -0.0012C(io) + 0.352. The flowrate required to attain an effluent TSS concentration of 50 mg/L (Q(ss50)) at different influent TSS concentrations (C(iss)) can be represented by Q(ss50) x 10(-5) = 1.0 x 10(6) C(iss)(-2.9576). The smallest removable solid particle size was 4.87 microm.     

Empirical correlations to estimate agglomerate size and deposition during injection of a polyelectrolyte-modified Fe0 nanoparticle at high particle concentration in saturated sand

Controlled emplacement of polyelectrolyte-modified nanoscale zerovalent iron (NZVI) particles at high particle concentration (1-10 g/L) is needed for effective in situ subsurface remediation using NZVI. Deep bed filtration theory cannot be used to estimate the transport and deposition of concentrated polyelectrolyte-modified NZVI dispersions (>0.03 g/L) because particles agglomerate during transport which violates a fundamental assumption of the theory. Here we develop two empirical correlations for estimating the deposition and transport of concentrated polyelectrolyte-modified NZVI dispersions in saturated porous media when NZVI agglomeration in porous media is assumed to reach steady state quickly. The first correlation determines the apparent stable agglomerate size formed during NZVI transport in porous media for a fixed hydrogeochemical condition. The second correlation estimates the attachment efficiency (sticking coefficient) of the stable agglomerates. Both correlations are described using dimensionless numbers derived from parameters affecting deposition and agglomeration in porous media. The exponents for the dimensionless numbers are determined from statistical analysis of breakthrough data for polyelectrolyte-modified NZVI dispersions collected in laboratory scale column experiments for a range of ionic strength (1, 10, and 50mM Na(+) and 0.25, 1, and 1.25 mM Ca(2+)), approach velocity (0.8 to 55 × 10(-4)m/s), average collector sizes (d(50)=99 μm, 300 μm, and 880 μm), and polyelectrolyte surface modifier properties. Attachment efficiency depended on approach velocity and was inversely related to collector size, which is contrary to that predicted from classic filtration models. High ionic strength, the presence of divalent cations, lower extended adsorbed polyelectrolyte layer thickness, decreased approach velocity, and a larger collector size promoted NZVI agglomeration and deposition and thus limited its mobility in porous media. These effects are captured quantitatively in the two correlations developed. The application and limitations of using the correlations for preliminary design of in situ NZVI emplacement strategies is discussed.     

水环境中腐殖酸的荷电特性与聚集特性

通过腐殖酸的Zeta电位和粒径的变化规律研究,探讨化学条件对腐殖酸的荷电状态和聚集状态的影响。结果表明,腐殖酸具有自我凝聚的特性;在pH较低和溶液离子强度较高时,腐殖酸胶粒的Zeta电位绝对值减小而聚合度增大,从而使腐殖酸胶粒聚集而凝聚;随腐殖酸浓度增大,腐殖酸胶粒的Zeta电位绝对值增大,腐殖酸胶粒的缩聚程度降低而使粒径减小。     

活性焦和活性炭负载纳米铁处理TNT红水中的二硝基甲苯磺酸钠

以活性焦和活性炭为载体,采用液相还原法制备了负载纳米铁,比较了两种负载纳米铁对TNT红水中难降解物质二硝基甲苯磺酸钠(包括2,4-DNT-3-SO3Na和2,4-DNT-5-SO3Na)的去除能力。实验结果表明,作为负载材料活性焦的相对有效比表面积与孔体积要优于活性炭,而且有利于更好地发挥出负载纳米铁的优势。单位面积活性焦负载纳米铁去除2,4-DNT-5-SO3Na的能力明显高于活性炭负载纳米铁,单位面积活性焦负载纳米铁去除2,4-DNT-3-SO3Na的能力在较小投加量条件下高于活性炭负载纳米铁,但均随投加量的增加而下降;而对于活性炭负载纳米铁,其单位面积去除能力基本不受投加量的影响,而且对二硝基甲苯磺酸钠的去除率高于活性焦负载纳米铁。耦合混凝沉淀的总去除效果表明,单位面活性焦负载纳米铁对2,4-DNT-5-SO3Na的去除能力高于活性炭负载纳米铁,而对2,4-DNT-3-SO3Na的去除能力则低于活性炭负载纳米铁。     

Cosolvent flushing for the remediation of PAHs from former manufactured gas plants

Cosolvent flushing is a technique that has been proposed for the removal of hydrophobic organic contaminants in the subsurface. Cosolvents have been shown to dramatically increase the solubility of such compounds compared to the aqueous solubility; however, limited data are available on the effectiveness of cosolvents for field-contaminated media. In this work, we examine cosolvent flushing for the removal of polycyclic aromatic hydrocarbons (PAHs) in soil from a former manufactured gas plant (FMGP). Batch studies confirmed that the relationship between the soil-cosolvent partitioning coefficient (K(i)) and the volume fraction of cosolvent (f(c)) followed a standard log-linear equation. Using methanol at an fc of 0.95, column studies were conducted at varying length scales, ranging from 11.9 to 110 cm. Removal of PAH compounds was determined as a function of pore volumes (PVs) of cosolvent flushed. Despite using a high f(c), rate and chromatographic effects were observed in all the columns. PAH effluent concentrations were modeled using a common two-site sorption model. Model fits were improved by using MeOH breakthrough curves to determine fitted dispersion coefficients. Fitted mass-transfer rates were two to three orders of magnitude lower than predicted values based on published data using artificially contaminated sands.     

Influence of source characteristics, chemicals, and flocculation on chemically enhanced primary treatment.

The overall objective of this research was to investigate various methods and parameters to increase the efficiency of chemically enhanced primary treatment (CEPT). The performance of CEPT was evaluated based on its efficiency of removal of nonsettleable solids (NSS). Some of the source characteristics that influenced NSS concentration included influent total suspended solids, influent turbidity, and influent total chemical oxygen demand. A higher concentration of the influent constituents led to a higher NSS concentration, suggesting that NSS represented a somewhat fixed fraction or percent of these influent constituents. The specific particle surface area (SPSA) was found to correlate with percent NSS in the effluent. A higher SPSA is a result of smaller-sized nonsettleable colloidal particles, thus leading to an increase in percent NSS. In summary, there are several parameters that affect NSS, which could be used to control NSS to improve CEPT, as demonstrated by this study.     

Simulation of the evolution of particle size distributions in a vehicle exhaust plume with unconfined dilution by ambient air

Over the past several years, numerous studies have linked ambient concentrations of particulate matter (PM) to adverse health effects, and more recent studies have identified PM size and surface area as important factors in determining the health effects of PM. This study contributes to a better understanding of the evolution of particle size distributions in exhaust plumes with unconfined dilution by ambient air. It combines computational fluid dynamics (CFD) with an aerosol dynamics model to examine the effects of different streamlines in an exhaust plume, ambient particle size distributions, and vehicle and wind speed on the particle size distribution in an exhaust plume. CFD was used to calculate the flow field and gas mixing for unconfined dilution of a vehicle exhaust plume, and the calculated dilution ratios were then used as input to the aerosol dynamics simulation. The results of the study show that vehicle speed affected the particle size distribution of an exhaust plume because increasing vehicle speed caused more rapid dilution and inhibited coagulation. Ambient particle size distributions had an effect on the smaller sized particles (approximately 10 nm range under some conditions) and larger sized particles (>2 microm) of the particle size distribution. The ambient air particle size distribution affects the larger sizes of the exhaust plume because vehicle exhaust typically contains few particles larger than 2 microm. Finally, the location of a streamline in the exhaust plume had little effect on the particle size distribution; the particle size distribution along any streamline at a distance x differed by less than 5% from the particle size distributions along any other streamline at distance x.     

Persulfate oxidation of trichloroethylene with and without iron activation in porous media

In situ chemical oxidation with persulfate anion (S2O82*) is a viable technique for remediation of groundwater contaminants such as trichloroethylene (TCE). An accelerated reaction using S2O82* to destroy TCE can be achieved via chemical activation with ferrous ion to generate sulfate radicals (SO4*)(E degrees =2.6 V). The column study presented here simulates persulfate oxidation of TCE in porous media (glass beads and a sandy soil). Initial experiments were conducted to investigate persulfate transport in the absence of TCE in the column. The persulfate flushing exhibited a longer residence time and revealed a moderate persulfate interaction with soils. In TCE treatment experiments, the results indicate that the water or persulfate solution would push dissolved TCE from the column. Therefore, the effluent TCE concentration gradually increased to a maximum when about one pore volume was replaced with the flushing solution in the column. The presence of Fe2+ concentration within the column caused a quick drop in effluent TCE concentration and more TCE degradation was observed. When a TCE solution was flushing through the soil column, breakthrough of TCE concentration in the effluent was relatively slow. In contrast, when the soil column was flushed with a mixed solution of persulfate and TCE, persulfate appeared to preferentially oxidize soil oxidizable matter rather than TCE during transport. Hence, persulfate oxidation of soil organics may possibly reduce the interaction between TCE and soil (e.g., adsorption) and facilitate the transport of TCE through soil columns resulting in faster breakthrough.     

Influence of permeability on nanoscale zero-valent iron particle transport in saturated homogeneous and heterogeneous porous media

Environmental Science and Pollution Research - Nanoscale zero-valent iron (NZVI) particles can be used for in situ groundwater remediation. The spatial particle distribution plays a very important...     

PBTCA稳定零价纳米铁的制备及其去除水中Cr(Ⅵ)

以2-膦酸丁烷-1,2,4三羧酸(PBTCA)为稳定剂,通过FeCl3.6H2O与NaBH4反应,利用液相还原法制备稳定纳米级零价铁颗粒(P-NZVI),并用透射电子显微镜(TEM)、扫描电子显微镜(SEM)及X射线衍射(XRD)进行表征,颗粒平均粒径为73 nm。考察了Cr(Ⅵ)溶液初始浓度、pH、NZVI投加量、温度等条件对Cr(Ⅵ)去除效果的影响,并与同等条件下不加稳定剂制备的纳米铁(N-NZVI)进行对比。结果表明:Cr(Ⅵ)的去除率随温度和纳米铁投加量增加而升高,随pH和Cr(Ⅵ)溶液初始浓度升高而降低。在相同实验条件下,P-NZVI对Cr(Ⅵ)的去除效果明显优于N-NZVI,表明改性后纳米铁在地表水原位修复领域具有较好的应用前景。     

Factors diminishing the effectiveness of phosphorus loading from municipal effluent: critical information for TMDL analyses

Factors that diminish the effectiveness of phosphorus inputs from a municipal wastewater treatment facility (Metro) in contributing to phosphorus levels and its availability to support algae growth in a culturally eutrophic urban lake (Onondaga Lake, NY) were characterized and quantified. These factors included the bioavailability and settling characteristics of particulate phosphorus from this effluent, the dominant form (70%) of phosphorus in this input, and the plunging of the discharge to stratified layers in the lake. Supporting studies included: (1) chemical and morphometric characterization of the phosphorus-enriched particles of this effluent, compared to particle populations of the tributaries and lake, with an individual particle analysis technique; (2) conduct of algal bioavailability assays of the particulate phosphorus of the effluent; (3) conduct of multiple size class settling velocity measurements on effluent particles; and (4) determinations of the propensity of the discharge to plunge, and documentation of plunging through three-dimensional monitoring of a tracer adjoining the outfall. All of these diminishing effects were found to be operative for the Metro effluent in Onondaga Lake and will be integrated into a forthcoming phosphorus "total maximum daily load" analysis for the lake, through appropriate representation in a supporting mechanistic water quality model. The particulate phosphorus in the effluent was associated entirely with Fe-rich particles formed in the phosphorus treatment process. These particles did not contribute to concentrations in pelagic portions of the lake, due to local deposition associated with their large size. Moreover, this particulate phosphorus was found to be nearly entirely unavailable to support algae growth. While substantial differences are to be expected for various inputs, the effective loading concept and the approaches adopted here to assess the diminishing factors are broadly applicable.     

Overall dry deposition velocities of trace elements measured at harbor and traffic site in central Taiwan

For reasonable and convenient assessments of the characteristics of the dry deposition velocities between Taichung harbor site and Wuchi town site in central Taiwan, the overall dry deposition velocities of several metallic elements were calculated as the particulate diameter (D(p)) distributions of large particles (D(p) > 10 microm), coarse particles (10 microm < D(p) < 2.5 microm), and fine particles (D(p) < 2.5 microm) based on the ambient measurements during March-December of 2004. In this work, the dry deposition fluxes showed the higher correlation with coarse particle concentrations than large particle concentrations; however, the least well correlation was observed between the dry deposition fluxes and the fine particle concentrations. The calculated best-fit overall dry deposition velocities obtained using coarse particle concentrations varied from approximately 0.2 cm s(-1) for Cr to 1.5 cm s(-1) for Pb and 0.2 cm s(-1) for Fe to 2.6 cm s(-1) for Pb at Taichung harbor and Wuchi town site, respectively. In general, the crustal elements had higher deposition velocities than anthropogenic elements. In addition, overall dry deposition velocities for crustal elements were higher in Wuchi town site than in Taichung harbor site. The results identified the dry deposition flux was mainly contributed from large and coarse particles due to their high deposition velocities. The results also indicated that the best approach to estimate overall dry deposition was by depending on the characteristics of particles with diameters larger than 2.5 microm.     

Ammonia removal from compost leachate using zeolite. II. A study using continuous flow packed columns

Bench-scale packed zeolite columns were set up and operated to investigate the continuous removal of ammonium ions from compost leachate. The effects of hydraulic retention time (HRT), and particle size of the zeolite on the ammonia adsorption capacity were studied. For both the coarse particle and the powdered zeolite columns, higher ammonia removal efficiencies were achieved with longer HRT (i.e., lower influent flow rate) tests. At the same HRT, ammonia removal efficiencies from tests with powdered zeolite were generally 20% higher than tests with the coarse particle zeolite. A HRT of 6 hours was found appropriate for efficient ammonia removal, and an operating capacity of 1.31 mg N/g zeolite was obtained. Over 98% of the ammonia input from the influent was consistently removed for over 5 bed volumes (BV) of compost leachate flowing through the zeolite column. Zeolite proved to have a great potential as a medium for ammonia removal in treating composting leachate.     

AMMONIA REMOVAL FROM COMPOST LACHATE USING ZEOLITE. II. A STUDY USING CONTINUOUS FLOW PACKED COLUMNS

Bench-scale packed zeolite columns were set up and operated to investigate the continuous removal of ammonium ions from compost leachate. The effects of hydraulic retention time (HRT), and particle size of the zeolite on the ammonia adsorption capacity were studied. For both the coarse particle and the powdered zeolite columns, higher ammonia removal efficiencies were achieved with longer HRT (i.e., lower influent flow rate) tests. At the same HRT, ammonia removal efficiencies from tests with powdered zeolite were generally 20% higher than tests with the coarse particle zeolite. A HRT of 6 hours was found appropriate for efficient ammonia removal, and an operating capacity of 1.31 mg N/g zeolite was obtained. Over 98% of the ammonia input from the influent was consistently removed for over 5 bed volumes (BV) of compost leachate flowing through the zeolite column. Zeolite proved to have a great potential as a medium for ammonia removal in treating composting leachate.     

A2／O-MBR工艺处理低负荷污水并回用

将A2／O生物处理单元与MBR相结合构建了的处理能力为2000m3／d的A2／O—MBR工艺,并应用于缺水地区校园生活污水的处理与回用。该系统运行稳定,运行阶段的实验结果表明,在进水COD为100-200mg／L、NH4＋-N为19～33mg／L、TN为25-43mg／L、TP为35mg／L和低碳氮比的情况下,出水水质优于《城市污水再生利用城市杂用水水质》（GB／T18920-2002）的要求,且全部用于杂用及校园绿化等。经分析该工艺运行成本为0．96元／m3,每年可节省自来水73万t,获得较好的环境效益与经济效益。