纳米Al_2O_3固定化红平红球菌菌球的制备及其对苯酚的降解

以海藻酸铝为主要包埋材料、纳米Al_2O_3为添加剂,包埋固定红平红球菌,制得纳米Al_2O_3固定化红平红球菌菌球,并将其用于苯酚的降解。表征结果显示:菌球内部包含丰富的菌丝体;内部孔径以中孔居多。实验结果表明:菌球的最优制备方案为0.05 g纳米Al_2O_3加入3 m L海藻酸钠溶液中、海藻酸钠质量分数6%、微生物包埋量0.5 m L/m L(以海藻酸钠溶液计)、Al_2(SO_4)_3质量分数3%;在初始苯酚质量浓度为400 mg/L、反应时间为24h、菌球加入量为8 g/L、反应p H为8.0、反应温度为30℃的条件下,菌球首次使用时可使苯酚完全降解,使用5次后的苯酚降解率仍达93%以上,具有良好的循环使用性。     

专利文摘

固定化白腐菌和恶臭假单胞菌用于染料废水连续处理方法及装置该发明公开了一种固定化白腐菌和恶臭假单胞菌用于染料废水连续处理的方法及装置,染料废水连续处理装置包括两个白腐菌反应器和一个恶臭假单胞菌反应器,三者串联在一起。在下述条件下处理染料废水取得了显著的效果:控制处理装置水浴温度在28～32℃,对应每个反应器中染料废水与所述的固定化菌的体积比为1∶(0.08～0.12),控制废水进水流量为3～7 mL/min,溶解氧质量浓度为4～8 mg/L,每隔24 h测定染料废水的色度和COD     

镰刀菌HJ01对苯酚的降解性能

为了研究真菌对苯酚的降解能力,采用本实验室分离的一株镰刀菌HJ01,考察了外加碳源、降解体系初始pH、温度对HJ01菌体生长量和苯酚降解效果的影响,初步探讨了镰刀菌降解苯酚的动力学与机理。实验结果表明,该菌能以苯酚为惟一碳源生长,添加适量的蔗糖可促进HJ01菌体的生长及苯酚的降解。在蔗糖加入量为3g／L、降解体系初始pH为6．0、温度为30℃的最佳条件下,经HJ01菌处理4d后的质量浓度为420mg／L苯酚废水中的苯酚完全降解。镰刀菌的生长和苯酚降解动力学符合Andrews模型。     

固定化白腐真菌反应器与接触氧化反应器联用处理癸二酸生产废水

采用固定化白腐真菌(WRF)反应器与接触氧化反应器联用处理癸二酸废水。在WRF反应器中,以汽曝玉米秸秆为载体,并添加铜、铁促进白腐真菌生长和产酶作用,载体的使用寿命约为45 d。在进水苯酚平均质量浓度为69.36 mg/L、平均进水COD为1 648.81 mg/L的条件下,经WRF反应器处理后,苯酚平均质量浓度降至7.59 mg/L,平均出水COD降至478.03 mg/L;再经接触氧化反应器处理后,苯酚平均质量浓度降至1.65 mg/L,平均出水COD降至297.31 mg/L。     

对亚硝基苯酚废水处理的研究

本文研究了对亚硝基苯酚废水生化处理的可行性以及热缩聚和溶剂萃取的工艺过程。结果表明,对亚硝基苯酚废水的生化降解性差;热缩聚法可使废水色度、苯酚和 COD 浓度明显降低;经热缩聚处理过的废水再用 TBP(磷酸三丁酯)溶剂萃取,可进一步降低色度和苯酚、COD 的浓度。     

高压脉冲放电等离子体处理活性红X-3B染料废水

采用高压脉冲放电等离子体技术对活性红X-3B染料废水进行处理,考察了废水电导率、脉冲电压、脉冲频率、针板间距以及曝气量对处理效果的影响。实验结果表明,当废水电导率为200μS/cm、脉冲电压为34kV、脉冲频率为60Hz、针板间距为15mm、曝气量为12L/h、处理时间为60m in时,活性红X-3B染料废水脱色率能达到98.6%。     

湿法腈纶废水的生化处理

采用水解酸化—固定化微生物流化床—氧化混凝联合工艺处理湿法腈纶废水.该工艺采用的高效菌微生物固定化技术及新型氧化混凝技术均对湿法腈纶废水有较好的处理效果.实验结果表明:在水解酸化温度为42℃、水解酸化运行周期为20 h的条件下,接种活性污泥和高效菌的SBR的COD去除率为26.0％;在新型氯铁型氧化混凝剂加入量为15 mL/L的条件下,混凝出水COD可降至66 mg/L.水解酸化—固定化微生物流化床—氧化混凝联合工艺的总COD去除率可达89.4％.     

活性污泥的固定化及其性能研究

用改进聚乙烯醇-硼酸法将活性污泥制成固定化颗粒,考察了改进聚乙烯醇-硼酸法的最佳条件及固定化颗粒的性能。实验结果表明：改进聚乙烯醇-硼酸法的最佳条件为聚乙烯醇质量分数6．5％、包泥比（包埋剂与活性污泥质量比）1．2：1、二氧化硅质量分数1．5％、活性炭质量分数0．3％、海藻酸钠质量分数0．6％;用最佳条件下制得的固定化颗粒处理模拟化工废水,连续运行15d后的COD去除率达90％以上,且固定化颗粒耐冲击负荷和pH变化能力强;固定化颗粒对模拟化工废水的COD去除速率随进水COD的变化曲线类似于米氏方程所描述的反应初速度随底物浓度的变化规律。     

臭氧氧化—曝气生物滤池联合工艺处理低温高浓度苯酚废水

采用臭氧氧化—曝气生物滤池( BAF)联合工艺处理低温高浓度苯酚模拟废水.应用Design - Expert 7.1设计系统对臭氧氧化高浓度苯酚模拟废水进行了参数优化.实验结果表明:在低温(5 ～ 10℃)、臭氧加入量为0.67 g/L、进水pH为9.85的条件下,臭氧氧化出水苯酚质量浓度为1 237.6 mg/L,苯酚去除率为38.12％;臭氧氧化后的废水经调节pH至7.00 ～8.00后进入BAF,经BAF处理后的出水苯酚质量浓度小于0.5 mg/L.该工艺操作简单,处理效果稳定,出水水质达到GB8978-1996《污水综合排放标准》.     

干法腈纶生产废水脱氨氮研究

采用本实验室富集驯化的高效硝化细菌对生化处理后的干法腈纶生产废水进行了脱NH3-N研究,在连续运行装置中考察了DO和MLSS的变化特征,并研究了废水NH3-N负荷和COD负荷对脱NH3-N效果的影响.实验结果表明:该菌能适应干法腈纶生产废水中的难生物降解物质并有效去除废水中的NH3-N,启动期DO呈现"高-低-高"的变化,运行期污泥增长速率呈现"S"型变化;进水NH3-N负荷达到0.405 kg/(m3·d)时仍能维持出水P(NH3-N)在5 mg/L以下,进水COD负荷由0.126 kg/(m3·d)提高到0.975 kg/(m3·d)的过程中,NH3-N去除率始终高于96%.     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Historical Weathering Based on Chemical Analyses of Two Spodosols in Southern Sweden

Chemical weathering losses were calculated for two conifer stands in relation to ongoing studies on liming effects and ash amendments on chemical status, soil solution chemistry and soil genesis. Weathering losses were based on elemental depletion trends in soil profiles since deglaciation and exposure to the weathering environment. Gradients in total geochemical composition were assumed to reflect alteration over time. Study sites were Horröd and Hasslöv in southern Sweden. Both Horröd and Hasslöv sites are located on sandy loamy Weichselian till at an altitude of 85 and 190 m a.s.l., respectively. Aliquots from volume determined samples from a number of soil levels were fused with lithium metaborate, dissolved in HNO₃, and analysed by ICP – AES. Results indicated highest cumulative weathering losses at Hasslöv. The weathering losses for the elements are in the following order:Si > Al > K > Na > Ca > MgTotal annual losses for Ca+Mg+K+Na, expressed in mmol_c m^-2 yr^-1, amounted to c. 28 and 58 at Horröd and Hasslöv, respectively. Variations between study sites could not be explained by differences in bulk density, geochemistry or mineralogy. The accumulated weathering losses since deglaciation were larger in the uppermost 15 cm than in deeper B horizons for most elements studied.     

Transformations of nitrogen at the interface between the topsoil and an impervious clay subsoil

Much work has been done on gaseous emissions and leaching of nitrogenous compounds from whole soil profiles and also from soil surface measurements which are assumed to be mainly due to topsoil activity. In soils with an impervious clay subsoil, the boundary between the topsoil and subsoil may provide an interface for microbial activity, including N transformations. In this study, we investigated movement and transformations of two reactive N species (nitrate and urea) at the subsoil interface using a series of replicate, intact soil blocks, under two contrasting watering regimes. We measured fluxes in both liquid and gaseous phases and demonstrated that nitrate reaching the subsoil interface does not necessarily leach into water systems, but may denitrify immediately and could, therefore, add to atmospheric pollution through N₂O production. On the other hand, ammonium reaching the subsoil interface either directly, or after mineralization, appears to be more mobile than expected and has the potential to pollute watercourses.     

The Spatial and Temporal Variation of Measured Urban PM10 and PM2.5 in the Helsinki Metropolitan Area

We have studied particulate matter (PM) concentrations,PM₁₀ and PM_2.5, measured in an urban air qualitymonitoring network in the Helsinki Metropolitan Area during1997–1999. The data includes PM₁₀ concentrationsmeasured at five locations (two urban traffic, one suburbantraffic, one urban background and one regional backgroundsite) and PM_2.5 concentrations measured at twolocations (urban traffic and urban background sites). Theconcentrations of PM₁₀ show a clear diurnal variation,as well as a spatial variation within the area. Bycontrast, both the spatial and temporal variation of thePM_2.5 concentrations was moderate. We have analysedthe evolution of urban PM concentrations in terms of therelevant meteorological parameters in the course of oneselected peak pollution episode during 21–31 March, 1998.The meteorological variables considered included wind speedand direction, ambient temperature, precipitation, relativehumidity, atmospheric pressure at the ground level,atmospheric stability and mixing height. The elevated PMconcentrations during the 1998 March episode were clearlyrelated to conditions of high atmospheric pressure,relatively low ambient temperatures and low wind speeds inpredominantly stable atmospheric conditions. The resultsprovide indirect evidence indicating that the PM₁₀concentrations originate mainly from local vehiculartraffic (direct emissions and resuspension), while thePM_2.5 concentrations are mostly of regionally andlong-range transported origin.     

Methane generation from corncobs treated with xylanolytic consortia

Consortia were developed for the treatment of corncobs for use as a feedstock in a biogas fermentor. The treatment of corncobs with xylanolytic consortia enhanced the production of methane and biogas. All five consortia developed produced the maximum biogas and methane at a 6% loading rate and 20 days hydraulic retention time (HRT). The maximum biogas yield of 0.59m³/kg volatile solids (VS) with a methane content of 62% was produced with the KK-10 consortium. This was apparently due to a maximum hemicellulose degradation of 88%.     

Recovery of Acidified Lakes: Lessons From Sudbury, Ontario, Canada

Over 7,000 lakes around Sudbury, Ontario, Canada were acidified by S deposition associated with emissions from the Sudbury metal smelters and more distant S sources. Air pollution controls have led to widespread changes in damaged Sudbury lakes, including increased pH and decreased concentrations of SO₄, metals and base cations. While chemical improvements have often been substantial, many lakes are still acidified, although water quality recovery is continuing. Biological recovery has been observed in some lakes among various groups of organisms including fish, zooplankton, phytoplankton and zoobenthos. Generally, however, biological recovery is still at an early stage. Lakes around Sudbury are also showing that the recovery of acid-damaged lakes is closely linked to the effects of other major environmental stressors such as climate change, base cation depletion and UV-B irradiance. Future studies of the recovery of acid-damaged lakes around Sudbury, and in other regions, will need to consider the interactions of these and other stressors.     

Preparation and Biodegradation of Starch/Polycaprolactone Films

Starch granules were modified with trisodium trimetaphosphate (TSTP) and characterized by P³¹-NMR, FTIR and DSC. Seventy-micron films were prepared from modified starch and polycaprolactone blends by solvent casting technique. Three different types of films—PCL (100% polycaprolactone), MOD-ST/PCL (50% modified starch and 50% polycaprolactone blend) and NONMOD-ST/PCL (50% nonmodified starch and 50% polycaprolactone blends)—were prepared, and their thermal, mechanical, and morphologic properties were investigated to show the increased performance of PCL with the addition of starch and also the effect of modification. It was observed that with the addition of starch the Young's modulus of polycaprolactone was increased and became less ductile, whereas tensile strength and elongation at break values decreased. Biodegradation of these films was inspected under different aerobic environments with the presence of Pseudomonas putida, activated sludge, and compost. It was observed that whereas P. putida had almost no effect on degradation during 90 days, with the presence of activated sludge, considerable deformation of films was observed even in the first 7 days of degradation. In a compost environment, degradation was even faster, and all polymer films were broken into pieces within first 7 days of degradation and no film remained after 15 days.