杂多酸水溶液脱除烟气中SO2的性能研究

合成了H3PMo12O40、H4SiW12O40、H3PW12O40、H4PMo11VO40、H5PMo10V2O40和H6PMo9V3O406种杂多酸,分别采用红外光谱（FT-IR）和X射线衍射（XRD）表征杂多酸的结构,并采用气相色谱仪对6种杂多酸水溶液进行脱硫实验测试。实验结果表明：制备的6种杂多酸具有良好的Keggin型结构;H3PMo12O40、H3PW12O40和H4SiW12O40的3种水溶液中,磷钼杂多酸的脱硫性能最好,脱硫率在120 min时可达到16.38%;不同比例的多原子也会使杂多酸有不同的脱硫性能,脱硫性能顺序为：H6PMo9V3O40〉H5PMo10V2O40〉H4PMo11VO40;且6种杂多酸的脱硫稳定性的顺序为：H4PMo11VO40〉H6PMo9V3O40〉H3PMo12O40〉H5PMo10V2O40〉H4SiW12O40≈H3PW12O40。     

过氧化氢/磷钼酸体系的催化机制及对苯胺的降解效果

以苯胺为目标污染物,通过苯胺的降解实验从3类6种过氧化氢催化剂中筛选出催化效果较好的杂多酸催化剂磷钼酸(PMA).利用氧化还原电位测定法、电子顺磁共振波谱法、化学发光法以及拉曼光谱法分析了H2O2/PMA催化体系的催化机制,初步推测PMA催化H2O2生成高活性的[Mo(OO)2]*和[Mo(OOH)2]*中间体.同时,...     

电-Fenton法处理页岩气压裂返排液

页岩气开发压裂返排液处理是近年的研究热点,本文采用电-Fenton氧化技术对压裂返排液絮凝出水进行深度处理研究,主要考察了H2O2投加量、pH值、电压和反应时间对COD去除效果的影响。通过正交实验和单因素影响实验,确定电-Fenton氧化处理絮凝出水的适宜条件为:H2O2投加量为40 mL·L~(-1)、pH=3、电压6 V和反应时间60 min。在此条件下,出水COD为71.3 mg·L~(-1),COD去除率达到62.5%。实验结果表明化学絮凝—电-Fenton氧化是页岩气压裂返排液达标外排的一种适宜处理工艺。     

vis/H2O2/草酸铁处理活性艳红染料的实验研究

采用vis/H2O2/草酸铁法,对活性艳红染料废水进行处理.研究了H2O2、K2C2O4和Fe2(SO4)3·7H2O的投加量、pH值和光照时间等因素对染料废水处理效果的影响和最佳处理条件.结果表明,pH值2.5;30%H2O2的投加量0.1 mL;0.1 mol/L Fe2(SO4)3·7H2O的投加量1.0 mL;0.1 mol/L K2C2O4的投加量1.5 mL;光照时间40 min的最佳条件下,70 mg/L的活性艳红模拟染料废水脱色率可达99.82%.通过对vis/H2O2/草酸铁法和Fenton法、H2O2法、草酸铁法等方法进行对比实验,vis/H2O2/草酸铁法明显优于其他方法,是一项有研究价值和开发应用前景的污染治理新技术.     

酸碱改性对活性焦烧结烟气脱硫性能的影响

选取一定目数范围的活性焦,用3种酸(HCl、H2SO4和HNO3)、3种碱(KOH、NaOH和NH3·H2O)和酸碱两步(HNO3和KOH)对其进行改性处理,对比这几种方法改性的活性焦对烧结烟气的脱硫性能,实验结果表明,20~40目范围的活性焦脱硫性能最好;HCl改性活性焦的脱硫性能基本无变化,HNO3改性后有促进作用但作用不大,H2SO4改性反而降低了活性焦的脱硫活性;KOH和NaOH溶液改性活性焦对其脱硫性能有很大的提升作用,其中KOH改性效果更好,NH3·H2O改性基本无影响;先KOH后HNO3两步改性的活性焦效果最佳,并且能维持一定时间100%的脱硫效率。     

响应面法优化UV/H_2O_2光氧化法处理高浓度LAS废水

采用响应面法对UV/H2O2光氧化法处理高浓度LAS废水的工艺参数进行了系统研究。根据Box-Behnken Design(BBD)设计原理,以初始pH与H2O2投加量、反应时间和温度为主要影响因素,设计4因素3水平共29个实验点的实验方案,并建立了二次响应面拟合模型。方差分析表明,初始pH与H2O2投加量、反应时间和温度以及初始pH和H2O2投加量、H2O2投加量和温度之间的交互作用,对实验结果具有显著性影响。实验得到的光氧化高浓度LAS废水最佳工艺条件,pH为4.0,H2O2投加量为40 mmol/L,反应时间为90 min,温度为25℃,在此条件下,LAS的平均去除率为98.1%。     

H_4SiW_(12)O_(40)/TiO_2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶-凝胶法制备TiO2/beads光催化剂载体,然后浸渍法制备出H4SiW12O40/TiO2/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析.研究了H4SiW12O40/TiO2/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响.实验结果表明,在中性条件下,H4SiW12O40/TiO2/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%.     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶-凝胶法制备TiO2/beads光催化剂载体,然后浸渍法制备出H4SiW12O40/TiO2/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H4SiW12O40/TiO2/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明,在中性条件下,H4SiW12O40/TiO2/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

电-Fenton法降解TNT弹药销毁废水

2,4,6-三硝基甲苯(TNT)弹药销毁废水的色度高、毒性大、不易生化降解。采用电Fenton法降解TNT弹药销毁废水。研究了电压(U)、极板间距(D)、初始p H、H2O2投加量(M)、n(Fe2+)/n(H2O2)摩尔比及反应时间(T)对废水COD去除率的影响;优化了反应条件:在U=8 V,D=1 cm,初始p H=3,M(H2O2)=0.0916 mol/L,n(Fe2+)/n(H2O2)=1∶30,T=4 h的条件下,废水的COD去除率大于86%,出水的其余指标如色度、氨氮、p H、TNT含量等各指标经国标法测量均达标。通过对反应动力学方程的分析,得出该实验基本符合二级反应动力学。该法操作简单实用,是处理该废水行之有效的方法。     

Fenton试剂处理电厂离子交换树脂再生废水

采用 Fenton试剂对电厂离子交换树脂再生废水进行催化氧化处理 ,实验结果表明 ,当溶液 p H=2 .0、H2 O2 ( 30 % )投加量为 6 0 m L/L、F e SO4· 7H2 O投加量为 4.5 g/L、H2 O2 投加次数为 4、反应时间为 1.5 h时 ,废水的处理效果最佳     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.