麦饭石对重金属离子的吸附作用研究

研究了麦饭石对重金属离子，如Ｐｂ＾２＋、Ｃｕ＾２＋，Ｚｎ＾２＋，Ｃｄ＾２＋的吸附作用，实验结果表明，麦饭石对重金属离子具有较强的吸附性能，ｐＨ是影响吸附的主要因素，探讨了麦饭石吸附作用机理，认为离子交换和表面络合反应是主要的吸附形式。并结合对实际重金属废水的吸附净化作用讨论麦饭石在废水处理方面应用的可行性。     

共存离子对硫酸盐还原菌（SRB）处理含铬废水的影响研究

报道了用硫酸盐还原菌（ＳＲＢ）处理含铬（ＶＩ）废水时，共存离子Ｓｒ＾２＋，Ｃｄ＾２＋，Ｚｎ＾２＋，ＵＯ＾２＋２，Ａｇ＾＋和Ｃｌ＾－，ＳＯ２－４，ＣＯ＾２－３，ＳｉＦ＾２－６，ＥＤＴＡ柠檬酸根等存在的时的影响，在铬（ＶＩ）为５０μｇ／ｍＬ，菌量一定的条件下，铬的去除率可达８５％以上，共存离子与铬（ＶＩ）的摩尔比为４时影响较为显著，Ｃｄ＾２＋和Ａｇ＾＋使铬的去除量降低，ＵＯ＾２＋２，Ｓｒ＾２＋，Ｚｎ＾     

甲壳素,壳聚糖及其衍生物在水处理中的应用

对甲壳素、壳聚糖及其衍生物在水处理中的应用研究进行了综述。甲壳素、壳聚糖及其午睡了子的吸附剂（螯合剂）,能有效地去除水体中的Ｈｇ＾２＋、Ｃｄ＾２＋、Ｃｕ＾２＋、Ｎｉ＾２＋等有毒重金属离子;作为絮凝剂能除去废水中的悬浮物、染料、ＤＤＴ及石油等污染物;作为新型分离膜材料在水处理中的应用有广阔的前景。     

谷子谷壳黄原酸酯对重金属离子的捕集作用

制备并研究了谷子谷壳黄原酸酯对Ｈｇ＾２＋、Ｐｂ＾２＋、Ｃｄ＾２＋、Ｃｕ＾２＋、Ｃｏ＾２＋、Ｃｒ＾３＋、Ｂｉ＾３＋等七种重金属离子的捕集效果，结果表明，中性或碱性介质中，谷子谷壳黄原酸酯对重金属离子有良好的捕集效果。     

交联壳聚糖对重金属离子的吸附性能研究

以海蟹壳为原料制备的壳聚糖在碱性条件下,经环氧氯丙烷交联制得水不溶性的交联壳聚糖,采用静态法研究交联壳聚糖对Ｃｕ＾２＋,Ｃｒ＾３＋,Ｎｉ＾２＋,Ｐｂ＾２＋,Ｚｎ＾２＋,Ｈｇ＾２＋等几种重金属离子的吸附性能及ｐＨ值对吸附性能的影响,探讨了它们的作用机理。     

接枝羧基淀粉去除水体中有毒重金属离子的研究

以可溶性淀粉为基体，经环氧氯丙烷交联，制备了交联淀粉。以Ｆｅ＾２＋－Ｈ２Ｏ为引发剂将丙烯腈单体接枝到交联淀粉上，再经过皂化制得水不溶性接枝羧基淀粉聚合物（ＩＳＣ）。通过红外光谱表征结构。用静态法和动态法研究ＩＳＣ去除水体中Ｃｄ＾２＋、Ｐｂ＾２＋、Ｃｕ＾２＋、Ｈｇ＾２＋、Ｃｒ２＋等离子的效果及ＰＨ值对去除效果的影响，并对其作用机理进行探讨。     

活性硅酸混凝剂PFASSC处理造纸废水

利用硅酸钠、硫酸铝、三氯化铁和硫酸为主要原料制备了复合型活性硅酸混凝剂ＰＦＡＳＳＣ并对造纸废水进行了处理，得到活性硅酸混凝剂ＰＦＡＳＳＣ最佳配方为：ＰＨ＝２．０（Ｆｅ＾３＋＋Ａｌ＾２）／ＳｉＯ２（摩尔比）＝１．５，Ｆｅ＾３＋／Ａｌ＾３＋（摩尔比）＝１．０，与常用混凝剂相比，ＰＦＡＳＳＣ混凝剂处理造纸废水对除浊、脱色和去除ＣＤＤＣｒ有更加优良的性能。     

电化学法去除SO2／NOx的研究进展

本文对采用电化学方法去除ＳＯ２／ＮＯｘ废气这一新的研究方法进行了综述,在用酞花青钴（ＣｏＰｃ）修饰的碳气体扩散电极上,ＳＯ２在空气中的体积百分数在２０％以下时可以完全被氧化为硫酸,以连二硫酸盐（Ｓ２Ｏ４＾２－４）作还原剂,Ｆｅ＾２＋－ＥＤＴＡ作络合剂时,ＮＯ可以９０％以上的程度还原为ＮＨ＾＋４与ＮＨ２（ＳＯ３Ｈ）等低价含氮化合物,产物中未见Ｎ２、Ｎ２Ｏ与ＮＯ２等气体,氧化产物ＳＯ＾２－３（或ＨＳＯ     

H2O2—Fe^2＋／TiO2—H2SO4处理废有机溶剂的研究

放射性废有机溶剂是核设施产生的中低放废液，研究了废有机溶剂（ＴＢＰ／ＯＫ）在Ｈ２Ｏ２－Ｆｅ＾２＋／ＴｉＯ２体系中的氧化分解行为，分析了Ｈ２Ｏ２、催化剂（Ｆｅ＾２＋／ＴｉＯ２）、温度、ｐＨ值等因素对反应进程和效果的影响，还对主控因素进行四因素三水平的正交实验，最终确定了废有机溶剂氧化分解的适宜工艺条件。在此基础上进行的“热实验”表明，废有机溶剂氧化分解后其所携放射性核素主要富集在分解残液中，基本没有     

杀灭菊酯对鲤鱼血液影响初探

报道了杀灭菊酯杀虫剂对鲤鱼的血液系统的影响，结果表明，（１）杀灭菊酯引起鲤鱼血浆中离子浓度发生明显改变，Ｎａ＾＋下降１０％～２０％，Ｋ＾＋下降１０％～３５％，其它离子如Ｃｌ＾－，Ｃａ＾２＋，磷等则升高；同时还观察到Ｈｂ保持不变，（２）杀灭菊酯使ＲＢＣ渗透脆性增加，在体和体外处理均能引起ＲＢＣ破损，产生溶血，这很可能是杀灭菊酯对鱼类高毒的非神经作用的重要致毒原因之一。     

Comparison of the characteristics of flow-through and flow-around leaching tests of Solidified heavy metal wastes

This paper introduces a research work on studying the possibility of using a flow-through leaching test method to simulate the leaching behaviour of the cement-based stabilized/solidified (S/S) hazardous wastes. Both the flow-through leaching and the more common flow-around (dynamic leaching) test methods were carried out in the study to compare the leaching behaviour of the solidified waste under different leaching environments. The solidified waste samples were prepared from five kinds of heavy metals with two kinds of binders. The metals were Pb2+, Zn2+, Cu2+, Ni2+ (positive ions as nitrate), and Cr6+ (as a negative ion in potassium dichromate), and the binders were type I Ordinary Portland Cement (OPC) and Pulverised Fuel Ash (PFA). The results of two series of flow-through and flow-around leaching experiments are reported and compared in this paper. Mathematical models for simulating the leaching behaviour of the flow-through and flow-around leaching conditions were used to determine the diffusivities of the contaminants. The results show that, since the matrix of the solid waste in a flow-through leaching test is always being degraded, the diffusivities continuously increased during the leaching period. The range of the diffusivities was 10E-8 to 10E-3 cm2/s, which corresponds to the case of liquid phase diffusion. But in the case of the flow-around (dynamic leaching) test, the range of the diffusivities was 10E-18 to 10E-9 cm2/s which was similar to solid phase diffusion, and the variation of the diffusivity with time was not regular.     

2种浸出方法对水泥熟料的适用性比较

采用2种不同类型的代表性浸出方法:TCLP和NEN7371对不同重金属含量及不同烧制条件下所得水泥熟料进行浸出实验.结果表明,NEN7371方法下各样品中所有受试重金属几乎均有检出,大部分重金属的浸出率均高于10%;重金属的浸出浓度与其在熟料样品中含量的趋势对应性较好;TCLP方法下各样品中的受试重金属均只有部分检出,且浸出率一般在0.5%左右,浸出浓度很低,仪器检测误差较大.说明在考察水泥熟料中重金属的浸出特性时,NEN7371方法的适用性相对更好.     

Effect of calcite on Pb-doped solidified waste forms in leaching

The alkalinity of cementitious materials rectifies a low pH of leachant to be over 12 in leaching. The rapid change of leachant pH produces the remarked variation of solubility of heavy metals in the toxicity characteristic leaching procedure. The release of lead on cementitious solid waste forms in leaching was observed in the pH range of particularly 12. The release of lead is significant dependant on the changed values of leachant pH. The pH static leaching procedure (PSLP) was implemented for assessing a quantitative measurement of total potential leachability with the continuing addition of acidic leachant up to the point of no change of leachant pH. The release of lead on Pb-doped solidified waste forms (SWF), in the PSLP, was 27.0% of initial concentration at the maximum meq CH₃COOH (about 24.0) added to g dry solidified wastes. In this study, the immobilization effect of calcite on SWF was investigated in the acidic condition by the PSLP. Calcite additions to SWF make a good fixation efficiency of about 92%. Calcite addition abundantly provides the acid neutralization capacity to protect SWF from the attack of acid, with the marked development of hydrated minerals (mainly portlandite and C–S–H) in accordance with the accelerating effect of cement hydration.     

SGA对垃圾焚烧飞灰中重金属的固化性能研究

根据EPA1311、HJ／T299—2007、HJ／T300—2007和HJ557—2009等国内外不同标准,研究了深圳某垃圾焚烧发电厂垃圾焚烧飞灰的浸出毒性,探讨了六硫代胍基甲酸（sixthioguanidineacid,SGA）、二甲基二硫代氨基甲酸盐（sodiumdimethyldithiocarbamate,SDD）和Ca（OH）2浓度对垃圾焚烧飞灰中重金属的固定性能的影响。研究结果表明,随着浸提液pH的降低,该厂焚烧飞灰中大部分金属元素的浸出量增大,焚烧飞灰浸出液中的cd、Ni、Ph和zn浓度分别超过国家危险废物鉴别标准（GB5085．3—2007）规定值的4．75倍、1．47倍、6．72倍和2．20倍,属于危险废弃物,必须进行稳定化处理。当固化剂SGA加入量为0．1mol／kg时,稳定化后的重金属浸出浓度已经低于危险废物鉴别标准,且对Cd、Cr、Cu和Pb的固化性能优于SDD和Ca（OH）2;当固化剂SGA、SDD和Ca（OH）2加入量为0．5mol／kg时,稳定化后的焚烧飞灰重金属浸出浓度均低于国家危险废物鉴别标准（GB5085．3-2007）中的规定值。与SDD和Ca（OH）：相比,SGA对垃圾焚烧飞灰中重金属的固化处理更具有优势。     

SGA对垃圾焚烧飞灰中重金属的固化性能研究简

根据EPA 1311、HJ/T 299-2007、HJ/T 300-2007和HJ 557-2009等国内外不同标准,研究了深圳某垃圾焚烧发电厂垃圾焚烧飞灰的浸出毒性,探讨了六硫代胍基甲酸（sixthio guanidine acid,SGA）、二甲基二硫代氨基甲酸盐（sodium dimethyl dithio carbamate,SDD）和Ca（OH）₂浓度对垃圾焚烧飞灰中重金属的固定性能的影响。研究结果表明,随着浸提液pH的降低,该厂焚烧飞灰中大部分金属元素的浸出量增大,焚烧飞灰浸出液中的Cd、Ni、Pb和Zn浓度分别超过国家危险废物鉴别标准（GB5085.3-2007）规定值的4.75倍、1.47倍、6.72倍和2.20倍,属于危险废弃物,必须进行稳定化处理。当固化剂SGA加入量为0.1 mol/kg时,稳定化后的重金属浸出浓度已经低于危险废物鉴别标准,且对Cd、Cr、Cu和Pb的固化性能优于SDD和Ca（OH）₂;当固化剂SGA、SDD和Ca（OH）₂加入量为0.5 mol/kg时,稳定化后的焚烧飞灰重金属浸出浓度均低于国家危险废物鉴别标准（GB 5085.3-2007）中的规定值。与SDD和Ca（OH）₂相比,SGA对垃圾焚烧飞灰中重金属的固化处理更具有优势。     

硫酸锰废渣浸出毒性及淋溶特性研究

长沙市兴镇13家硫酸锰厂的生产废渣使当地的生态环境造受到了严重破坏。本文在废渣浸出毒性实验、渣柱淋滤实验以及废渣的全分析基础上,全面地研究了废渣的组成、浸出毒性大小以及在当地酸沉降条件下的淋滤特征,为其安全处置提供了理论基础。研究证明,废渣中重金属种类多、含量高,尤其是锰,高达138800mg/kg。渣的浸出毒性虽未达到国家规定的危险废物鉴别标准,但远超过了《污水综合排放标准》,其衰减可用负指数方程来描述。在酸雨淋溶下,渣中的锰离子会在短时期内大量释放后,维持在一相对较低水平长期释放,对环境威胁巨大。     

Digested sewage sludge solidification by converter slag for landfill cover

A new technology for solidification of digested sewage sludge referred to as converter slag solidification (CSS) has been developed using converter slag as the solidifying agent and quick lime as the solidifying aid. The CSS technology was investigated by analyzing the physicochemical properties of solidified sludge and determining its microstructural characteristics. The feasibility of using solidified sludge as a landfill cover material was considered in the context of the economical recycling of waste. Sludge solidified using the CSS technology exhibited geotechnical properties that are appropriate for replacing currently used cover soil. Microscopic analyses using XRD, SEM and EDS revealed that the main hydrated product of solidification was CSH (CaO . SiO2 . nH2O), which may play an important role in the effective setting process. Negligible leaching of heavy metals from the solidified sludge was observed. The solidification process of the hydrated sludge, slag and quicklime eliminated the coliform bacteria. Recycled sewage sludge solidified using CCS technology could be used as an effective landfill cover.     

Stabilization and Solidification of Metal-Laden Wastes by Compaction and Magnesium Phosphate-Based Binder

ABSTRACT

Bench-scale and full-scale investigations of waste stabilization and volume reduction were conducted using spiked soil and ash wastes containing heavy metals such as Cd, Cr, Pb, Ni, and Hg. The waste streams were stabilized and solidified using chemically bonded phosphate ceramic (CBPC) binder, and then compacted by either uniaxial or harmonic press for volume reduction. The physical properties of the final waste forms were determined by measuring volume reduction, density, porosity, and compressive strength. The leachability of heavy metals in the final waste forms was determined by a toxicity characteristic leaching procedure (TCLP) test and a 90-day immersion test (ANS 16.1). The structural composition and nature of waste forms were determined by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively.

CBPC binder and compaction can achieve 80-wt % waste loading and 39-47% reduction in waste volume. Compressive strength of final waste forms ranged from 1500 to 2000 psi. TCLP testing of waste forms showed that all heavy metals except Hg passed the TCLP limits using the phosphate-based binder. When Na₂S was added to the binder, the waste forms also passed TCLP limits for Hg. Long-term leachability resistance of the final waste forms was achieved for all metals in both soil and ash wastes, and the leachability index was ~14. XRD patterns of waste forms indicated vermiculite in the ash waste was chemically incorporated into the CBPC matrix. SEM showed that waste forms are layered when compacted by uniaxial press and are homogeneous when compacted by harmonic press.     

Stabilization and solidification of metal-laden wastes by compaction and magnesium phosphate-based binder

Bench-scale and full-scale investigations of waste stabilization and volume reduction were conducted using spiked soil and ash wastes containing heavy metals such as Cd, Cr, Pb, Ni, and Hg. The waste streams were stabilized and solidified using chemically bonded phosphate ceramic (CBPC) binder, and then compacted by either uniaxial or harmonic press for volume reduction. The physical properties of the final waste forms were determined by measuring volume reduction, density, porosity, and compressive strength. The leachability of heavy metals in the final waste forms was determined by a toxicity characteristic leaching procedure (TCLP) test and a 90-day immersion test (ANS 16.1). The structural composition and nature of waste forms were determined by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. CBPC binder and compaction can achieve 80-wt% waste loading and 39-47% reduction in waste volume. Compressive strength of final waste forms ranged from 1500 to 2000 psi. TCLP testing of waste forms showed that all heavy metals except Hg passed the TCLP limits using the phosphate-based binder. When Na2S was added to the binder, the waste forms also passed TCLP limits for Hg. Long-term leachability resistance of the final waste forms was achieved for all metals in both soil and ash wastes, and the leachability index was approximately 14. XRD patterns of waste forms indicated vermiculite in the ash waste was chemically incorporated into the CBPC matrix. SEM showed that waste forms are layered when compacted by uniaxial press and are homogeneous when compacted by harmonic press.     

不同湿地植物凋落物对汞铊矿废弃物浸出酸性废水中重金属的吸附研究

研究了不同湿地植物(稻草(Oryza sativa L.)、风车草(Cyperus involucratus Rottb.)、芦竹(Arundo donax L.)、美人蕉(Canna indica L.)、水葱(Scirpus validus Vahl.)、香蒲(Typha orientalis C.Presl)和鸢...