The fate of recombinant plasmids during composting of organic wastes

Composting was investigated as a means for safe disposal of organic waste containing bacteria that carry transgenes in recombinant plasmids. To generate model recombinant plasmids, a mobile IncQ plasmid, RSF1010, and a non-mobile plasmid, pGFP, were genetically modified to carry a DNA segment encoding both green fluorescent protein and kanamycin resistance and were designated as RSF1010-GFPK and pGFPK. Escherichia coli (E. coli) C600 harboring these plasmids were inoculated into chicken manure specimens that were placed in compost at 20 and 60 cm from the bottom of a 1.0-m high compost bin. Control specimens were held at ambient temperature. By day 10, compost temperatures at the lower and upper levels of the bin had reached 45.3 and 61.5°C, respectively, and at both levels the target E. coli had been inactivated and the plasmids had lost their capacity to be transformed or mobilized. Furthermore, based on real time Polymerase chain reaction (PCR), the transgene fragments along with the host chromosomal DNA fragment from specimens at the upper level had been degraded beyond the detection limit. However, at the lower level where temperatures remained below 48°C these fragment persisted to day 21. At ambient temperatures (0–8°C), the E. coli, plasmids and the transgene fragments persisted in manure specimens throughout the 21 day test period. The study showed the potential for composting as a safe procedure for disposal of bacteria carrying transgenes in recombinant plasmids.     

Dissipation pathways of organic pollutants during the composting of organic wastes

The organic pollutants (OPs) present in compostable organic residues can be recovered in the final composts leading to environmental impacts related to their use in agriculture. However, the composting process may contribute to their partial dissipation that is classically evaluated through the concentration decrease in extractable OPs, without identification of the responsible mechanisms as mineralization or stabilization of OP as non-extractable residues (NER) or bound residues. The dissipation of four (14)C-labeled OPs (fluoranthene; 4-n-nonylphenol, NP; sodium linear dodecylbenzene sulfonate, LAS; glyphosate) was assessed during composting of sewage sludge and green waste. The dissipation of LAS largely resulted from its mineralization (51% of initial LAS), whereas mineralization was intermediate for NP (29%) and glyphosate (24%), and negligible for fluoranthene. The NER pathway mostly concerned NP and glyphosate, with 45% and 37% of the recovered (14)C being found as NER at the end of composting, respectively. In the final composts, the proportions of water soluble residues of OPs considered as readily available were <11% of recovered (14)C-OPs. However, most fluoranthene remained solvent extractable (72%) and potentially available, whereas only 18% of glyphosate and less than 7% of both NP and LAS remained solvent extractable in the final compost.     

Duckweed (Lemna gibba) growth inhibition bioassay for evaluating the toxicity of olive mill wastes before and during composting

Two-phase olive mill waste (TPOMW) is considered the main problem confronting the modern oil extraction and processing industry. Composting has been recently proposed as a suitable method to treat TPOMW so that it is suitable for use in agriculture. In the work reported here, the Lemna gibba bioassay was tested to assess the toxicity of TPOMW before and during the composting process. The method was compared with the Lepidium sativum bioassay and with other chemical maturity indices traditionally reported in the literature. The L. gibba test proved to be a simple, sensitive, and accurate method to evaluate toxicity before and during the composting of TPOMW. Plant growth response was measured by two methods: counting the number of fronds (leaves) and measuring total frond area (TFA) with image analysis software. Compared to the counting of fronds (L. gibba) or seeds (L. sativum), the use of area-measuring software permitted a very rapid, unbiased and easy way of analysing the toxicity of TPOMW before and during composting. Although the accuracy of the frond count method was similar to the traditional cress seed test, data analysis showed that the TFA measurement method was statistically more accurate (significantly lower variance) than the frond count approach. Highly significant correlations were found between TFA and some important maturation indices commonly reported in literature indicating that the L. gibba bioassay can be a useful tool to determine the degree of maturity of TPOMW composts.     

有机固体废物堆肥化处理的微生物学机理研究

由于符合持续发展的理念 ,利用微生物技术处理有机固体废物越来越受到人们的重视 ,其核心问题则是木质纤维素的生物降解。随着园林废物等高木质纤维素含量的城市生活垃圾的不断增加 ,以及对农业固体废物和食品工业废物再利用的需要 ,这一领域的研究取得了很大的进展。在研究中 ,针对好氧堆肥和厌氧发酵 2项主要的微生物处理技术 ,对其优势微生物菌群、不同降解底物和微生物降解动力学方面的最新研究进展进行了回顾和总结 ,并对环境微生物制剂的应用以及有机固体废物的微生物处理技术的发展做了合理的展望。     

Natural organic compounds as alternative to methyl bromide for nematodes control

Thirty-three organic acids and furfural metabolites were examined for their nematicidal activity against plant-parasitic, free-living and predacious nematodes. Propionic acid, 2-methylhexanoic acid, lactic acid, maleic acid, and furic acid were the most effective nematicides among normal chain organic acids, branched organic acids, hydroxy/keto-acids, dicarboxylic acids and furfural metabolites, respectively. Seven of the tested compounds were found to have more than 90% mortality thus designating them as highly active nematicides. Of the highly active tested compounds, an average octanol/water log P of 0.97 was observed with a range from 0.28 to 2.64, and a Henry's Law constant averaging 2.6 × 10^{? 7} atm.m³/mole. Tested chemicals with minor or low nematicidal activity showed an average log P of 1.76 with a range from 0.15 to 3.42 and a Henry's Law constant averaging 16.6 × 10^{? 7} atm.m³/mole.     

Natural organic compounds as alternative to methyl bromide for nematodes control

Thirty-three organic acids and furfural metabolites were examined for their nematicidal activity against plant-parasitic, free-living and predacious nematodes. Propionic acid, 2-methylhexanoic acid, lactic acid, maleic acid, and furic acid were the most effective nematicides among normal chain organic acids, branched organic acids, hydroxy/keto-acids, dicarboxylic acids and furfural metabolites, respectively. Seven of the tested compounds were found to have more than 90% mortality thus designating them as highly active nematicides. Of the highly active tested compounds, an average octanol/water log P of 0.97 was observed with a range from 0.28 to 2.64, and a Henry's Law constant averaging 2.6 x 10(- 7) atm.m3/mole. Tested chemicals with minor or low nematicidal activity showed an average log P of 1.76 with a range from 0.15 to 3.42 and a Henry's Law constant averaging 16.6 x 10(- 7) atm.m3/mole.     

Oxidative biodegradation of dissolved organic matter during composting

Dissolved organic matter (DOM) plays an important role in the microbial degradation of compost since it represents the most active organic fraction, both biologically and chemically. The detailed evaluation of the changes in the chemical and biochemical characteristics of DOM induced by oxidative biodegradation, presented in this work highlights the mechanisms involved in the degradation of soluble organic matter during composting. In fact, the results show that during the initial stages of composting, DOM is highly degradable under aerobic conditions, particularly due to the predominance of labile, hydrophilic compounds such as carbohydrates, amino acids and proteins. As such compounds are degraded more resistant aromatic moieties accumulate in solution resulting in a reduction in the degradability of DOM with composting time. This decrease in degradability was found to be highly correlated with microbial oxygen demand, and could have important implications in the evaluation of the composting process.     

Ammonia emissions from the composting of different organic wastes. Dependency on process temperature

Ammonia emissions were quantified for the laboratory-scale composting of three typical organic wastes with medium nitrogen content: organic fraction of municipal solid wastes, raw sludge and anaerobically digested sludge; and the composting of two wastes with high nitrogen content: animal by-products from slaughterhouses and partially hydrolysed hair from the leather industry. All the wastes were mixed with the proper amount of bulking agent. Ammonia emitted in the composting of the five wastes investigated revealed a strong dependence on temperature, with a distinct pattern found in ammonia emissions for each waste in the thermophilic first stage of composting (exponential increase of ammonia emitted when increasing temperature) than that of the mesophilic final stage (linear increase of ammonia emissions when increasing temperature). As composting needs high temperatures to ensure the sanitisation of compost and ammonia emissions are one of the main environmental impacts associated to composting and responsible for obtaining compost with a low agronomical quality, it is proposed that sanitisation is conducted after the first stage in large-scale composting facilities by a proper temperature control. CAPSULE: Ammonia emission pattern and correlation with process temperature are presented for the composting process of different organic wastes.     

Formation of chloromethoxybenzaldehyde during composting of organic household waste

Standardized household waste was mixed with different litter amendments, straw, leaves, hardwood shavings, softwood shavings, paper, and sphagnum peat, resulting in six compost mixtures. In addition non-amended household waste was composted. Composting was done in small rotatable bins and compost samples were taken on a regular basis until day 590. Extraction and analysis of wet compost samples showed no evidence for the presence of chloroorganic compounds. Drying and re-wetting of compost samples, however, revealed that chloromethoxybenzaldehyde (CMBA) was formed in all composts at concentrations varying between 5.6 and 73.4 microg kg(-1) dry matter. CMBA was not present in the original materials. During composting, there was a clear positive relation between formation of CMBA and microbial activity, as indicated by C losses and temperature. Formation took place during the most intensive phase of composting when C losses were highest. Under anaerobic conditions, however, which prevailed initially in the non-amended compost, no CMBA was formed. Calculation of total amounts of CMBA in composts revealed that there was a small decrease during storage in the hardwood, peat, and softwood composts. However, all composts contained CMBA after 590 days. The mean concentration was 33.4 microg kg(-1) dry matter (s.d. = 21.9). Possible biocidal effects of composts when used in cultivation may be explainable by the presence of natural toxic compounds formed during composting.     

Remediation of polycyclic aromatic hydrocarbon (PAH) contaminated soil through composting with fresh organic wastes

Introduction  

Composting may enhance bioremediation of PAH-contaminated soils by providing organic substrates that stimulate the growth of potential microbial degraders. However, the influence of added organic matter (OM) together with the microbial activities on the dissipation of PAHs has not yet been fully assessed.     

污泥用量对生活垃圾堆肥氮素转化与损失的影响

为了探讨生活垃圾堆肥的氮素损失问题,对生活垃圾（A组）、污泥和生活垃圾混合B组（w/w=1∶6）、C组（w/w=1∶4）组等3组物料进行高温好氧堆肥,研究污泥用量对生活垃圾堆肥化过程中温度、pH值、各氮素转化与损失的影响。结果表明：投加污泥会影响生活垃圾的通风性能,减慢物料的升温速率,延长堆肥周期。污泥用量对生活垃圾堆...     

鸡粪堆肥水溶性有机物转化特性研究

采用离子色谱和三维荧光光谱,分别对鸡粪堆肥不同阶段水溶性有机物(DOM)中典型小分子有机酸、磷酸和荧光有机物进行了研究。分析显示,所研究的7种酸(乙酸、琥珀酸、苹果酸、草酸、柠檬酸、酒石酸及磷酸)中,苹果酸的含量最高(1 000 mg/L),草酸的浓度最低(3 mg/L),琥珀酸和柠檬酸未检测到。随着堆肥的进行,各种酸的含量先上升而后下降,堆肥结束降至最低;堆肥过程样品所有荧光峰强度之和与COD达到显著相关(R=0.917,P0.05),类蛋白荧光峰强度与总荧光峰强度的比值不断降低,而类富里酸荧光峰强度与总荧光峰强度的比值不断上升。结果表明,堆肥过程小分子有机酸主要出现在堆肥中期;类蛋白荧光强度或类富里酸荧光强度与总荧光强度之比可以有效表征堆肥腐熟过程。     

Spectroscopic characterization of water extractable organic matter during composting of municipal solid waste

This paper aims to characterize the evolution of water extractable organic matter (WEOM) during the composting of municipal solid waste (MSW), and investigate the correlation between maturity and WEOM characteristics. WEOM was extracted at different stages of MSW composting (0, 7, 14, 21, and 51 d) and characterized by FTIR, UV-Vis, and fluorescence spectroscopy. The results obtained show that the composting process decreased aliphatics, alcohols, polysaccharides, as well as protein-like materials, and increased aromatic polycondensation, humification, oxygen-containing functional groups, molecular weight, and humic-like materials. The maturity of MSW during composting was characterized by the presence of the peak with an excitation/emission wavelength pair of 289/421 nm in excitation-emission matrix spectra.     

Impact of phosphate additive on organic carbon component degradation during pig manure composting

Phosphate, as an additive to composting, could significantly reduce ammonia emission and nitrogen loss but may also cause adverse effects on the degradation of organic matter. However, there is little information about the influence of pH change, salt content, and phosphate on different organic fraction degradation during composting with the addition of phosphate at a higher level. In this study, the equimolar phosphoric acid (H₃PO₄), sulfuric acid (H₂SO₄), and dipotassium phosphate (K₂HPO₄) were added into pig manure composting with 0.25 mol mass per kilogram of dry matter basis addition amount to evaluate the effect of H⁺, PO₄^3?, and salinity on carbon component transformation and organic matter degradation. The results showed that both H₃PO₄ and K₂HPO₄ additives could lead to shorter duration in the thermophilic phase, lower degradation of lignocellulose, and lesser carbon loss compared to CK, even though had different pH, i.e., acidic and alkaline conditions, respectively. Besides, the addition of H₃PO₄, H₂SO₄, and K₂HPO₄ could increase the degradation of soluble protein and lipid during composting. Redundancy analysis demonstrated that the variation in different organic carbon fractions was significantly correlated with the changes of pH and the presence of PO₄^3?, but not with SO₄^2? and electrical conductivity, suggesting that pH and phosphate were the more predominant factors than salinity for the inhibition of organic matter degradation. Taken together, as acidic phosphate addition produces a true advantage of controlling nitrogen loss and lower inhibition of organics transformation during composting, the expected effects may result in more efficient composting products.

     

Decolourization and removal of some organic compounds from olive mill wastewater by advanced oxidation processes and lime treatment

Background Olive mill wastewater (OMW) generated by the olive oil extracting industry is a major pollutant, because of its high organic load and phytotoxic and antibacterial phenolic compounds which resist biological degradation. Mediterranean countries are mostly affected by this serious environmental problem since they are responsible for 95% of the worldwide oliveoil production. There are many methods used for OMW treatment, such as adsorption, electro coagulation, electro-oxidation, biological degradation, advanced oxidation processes (AOPs), chemical coagulation, flocculation, filtration, lagoons of evaporation and burning systems, etc. Currently, there is no such economical and easy solution. The aim of this study was to evaluate the feasibility of decolourization and removal of phenol, lignin, TOC and TIC in OMW by UV/H₂O₂ (AOPs). The operating parameters, such as hydrogen peroxide dosage, times, pH, effect of UV and natural sunlight were determined to find the suitable operating conditions for the best removal. Moreover, there is no study reported in the literature related to the use of UV/H₂O₂ and lime together in OMW treatment. Methods OMW was obtained from an olive-oil producing plant (Muğla area of Turkey) which uses a modern production process. No chemical additives are used during olive oil production. This study was realised by using two different UV sources, while taking the time and energy consumption into consideration. These two sources were mercury lamps and natural sunlight. Before starting AOPs experiments, one litre of OMW was treated by adding lime until a pH of 7.00. Then, 100 ml was taken from each sample, and 1 to 10 ml of a 30% H₂O₂ (Riedel-deHaen) solution was added. These solutions in closed vessels were laid in the natural sunlight for a week and their compositions and colour changes were analysed daily by UV-Vis spectrophotometer. At the end of the one-week period, they were treated with lime. In this study, the effect of changes in the initial pH, times and H₂O₂ concentrations on removal was investigated. At the end of all experiments, changes in colour, phenol, lignin, TOC and TIC concentrations were analysed according to standard methods. Results and Discussion In the samples exposed to natural sunlight and having an H₂O₂/OMW ratio of 3 ml/100 ml, a significant colour removal was achieved approximately 90% of the time at the end of 7 days. When the same samples were treated with lime (pH: up to 7), 99% efficiency was achieved. When phenol and lignin removals were examined in the same concentration, phenol and lignin removal were found 99.5%, 35%, respectively. However, for maximum lignin removal, more use of H₂O₂ (10 ml H₂O₂/100 ml OMW) was found to be necessary. Under these conditions, it was found that lignin can be removed by 70%, but to 90% with lime, at the end of a seven-day period. Rate constants obtained in the experiments performed with direct UV were found to be much higher than those of the samples exposed to natural sunlight (k^a _lignin = 0.3883 ≫ k^b _lignin = 0.0078; k^a _phenol = 0.5187 ≫ k^b _phenol = 0.0146). Moreover, it should be remembered in this process that energy consumption may induce extra financial burden for organisations. Conclusions It was found, in general, that colour, lignin, total organic carbon and phenol were removed more efficiently from OMW by using H₂O₂ UV and lime OMW. Moreover, in the study, lime was found to contribute, both initially and after radical reactions, to the efficiency to a great extent. Recommendations and Perspectives Another result obtained from the study is that pre-purification carried out with hydrogen peroxide and lime may constitute an important step for further purification processes such as adsorption, membrane processes, etc.     

Influences of adding easily degradable organic waste on the minimization and humification of organic matter during straw composting

To find a better composting process with low greenhouse gas emission and high humus production, the effect of adding kitchen waste on reduction and humification of organic matter during straw composting was studied. Three processes were compared, consisting of different ratios of straw and kitchen waste (1:2, 1:1, and 2:1). At four time points over a 62-d incubation, the reduction and humification of compost was evaluated by measuring the total mass, carbon content, and humic material content of the compost. Treatment 1 (straw/kitchen waste ratio of 1:2) reduced the total mass of compost the most. Treatment 2 (straw/kitchen waste ratio of 1:1) reduced the total carbon content the most, reflecting the highest emission of greenhouse gas. Treatment 3 produced the most humic acid material and released the lowest amount of carbon. Hence, from the point of view of reducing greenhouse gas emissions and increasing stable organic matter such as humus and humic acid during composting, treatment #3 was optimal. The three treatments resulted in significant differences in microbial biomass and enzyme activity during composting. The highest amount of active microbial biomass was associated with the largest reduction in compost mass (treatment 1). Higher proportions of straw (treatments 2 and 3), which contains more lignin, were associated with greater β-glycosidase activity, which may generate more humus that can improve soil quality. Dehydrogenase activity seemed to be the most important microbial factor in organic carbon catabolism or humification.     

The effects of sulphur gas and elemental sulphur dust deposition on Pinus contorta x Pinus banksiana: cell walls and water relations

The bulk modulus of elasticity (E) for Pinus contorta (lodgepole pine) x Pinus banksiana (jack pine) hybrids was compared between a site (AI) close to a sour gas processing plant and a control site (AV). The mean bulk modulus of elasticity for branches from AI was 47.5 MPa vs 18.5 MPa for the control site (AV). Site AI had been exposed to S-gas emissions and large amounts of elemental S deposition and had an acidic soil (pH 4.0 at 10 cm depth). During 1981 the needles at AI had more aluminum and iron compared to those at AV (900 ppm vs 390 ppm AI in the 3-year-old needles). Mean leader growth was measured over a 3-year period and was observed to be greater at AI than AV (46+/-7 cm vs 29+/-9 cm for 1988). Histochemically, the needles at AI had higher phenol and lignin content than AV. These results suggest that the S-gas fumigation, S-dust deposition, plus increased concentrations of soluble aluminum and iron had altered the cell wall elastic properties resulting in altered water relations. The implications of this on leaf diffusive resistance and photosynthesis are discussed.     

A mild photochemical approach to the degradation of phenols from olive oil mill wastewater

Photooxidation of cathecol (1) is carried out in aqueous solution at lambda > 300 nm using different sensitizers: rose bengal (RB), 9,10-dicyanoanthracene (DCA), 2,4,6-triphenylpyrylium tetrafluoroborate (Pyryl). The highest degradation is observed in the UV/RB-sensitized reaction (66% after 15 h of irradiation), mineralization and formation of dimers are the final events. This procedure has been extended to tyrosol (2), caffeic acid (3), vanillic acid (4), 4-hydroxycinnamic acid (5) and 4-hydroxybenzoic acid (6) as well as to a mixture of all phenols. A reduced toxicity of the UV/RB-irradiated solutions of cathecol and tyrosol towards alga Ankistrodesmus braunii is also verified.     

Effect of vermicomposting on calcium,sulphur and some heavy metal content of different biodegradable organic wastes under liming and microbial inoculation

A study was conducted to evaluate the changes in total calcium and sulphur and some heavy metal (Zn, Cu, and Pb) concentration of different organic wastes affected by liming and microorganism inoculation. Vermicomposting was an effective technology for disposal of organic substrates like municipal solid wastes (MSW), possessing comparatively higher concentration of heavy metals. The addition of lime in initial organic substrates significantly (P ≤ 0.05) increased total calcium and total sulphur content of vermicomposts. Inoculation of microorganisms significantly (P ≤ 0.05) reduced the heavy metal content of final products as compared to control. Fungal strains were comparatively more effective in detoxification of heavy metals than B. polymyxa.     

广州典型灰霾期有机碳和元素碳的污染特征

使用小流量Partisol model 2000采样器每2 h采集广州典型灰霾期(2006年1月7～20日)PMlo样品,并用美国Sunset Laboratory Inc.的碳分析仪分析了有机碳和元素碳.结果显示,灰霾期PM10、有机碳和元素碳污染严重,最高浓度日均值(1月13日)分别为最低浓度日均值(1月20日)的10.1、7.6、3.0倍;大气污染存在一个明显的逐日上升和下降过程,上升期间PM10、有机碳和元素碳的日均增长率分别为(127±24)%、(125±16)%和(116±17)%.下降期间日均增长率分别为(-143±25)%、(-135±13)%和(-118±11)%.计算表明,二次有机碳污染严重,并随着灰霾污染的持续,占总有机碳比例增加.气团轨迹分析说明,珠江三角洲其他地区的污染对广州地区灰霾污染过程存在影响.