An ecotoxicological approach for hazard identification of energy ash

Within the EU, ash should be classified by its inherent hazardous effects under criterion H-14 (ecotoxic) in the Directive on waste (2008/98/EC). Today, however, there are no harmonized quantitative criterions for such a classification, but it is stated that biological test systems can be used. In this study seven ash materials were leached and characterized, both biologically and chemically. The objectives were to evaluate if (a) clear concentration-response relationships could be achieved for the selected toxicity tests (bacteria, algae, crustacean and fish), (b) some test(s) are generally more sensitive and (c) the toxic responses were consistent with the chemical analyzes. Interestingly, our results indicate that high concentrations of non-hazardous components (Ca, K) influenced the toxicity of almost all ash eluates, whereas hazardous components (e.g. Zn, Pb) only influenced the toxicity of the eluates ranked as most hazardous. If considering both hazardous and non-hazardous substances, the observed toxic responses were relatively consistent with the chemical analyzes. Our results further showed that the (sub)chronic tests were much more sensitive than the acute tests. However, the use of extrapolation factors to compensate for using the less sensitive acute tests will likely lead to either over- or underestimations of toxicity. Our recommendation is therefore that classification of waste according to H-14 should be based on (sub)chronic test data. Finally, given that treatment of the eluates prior to toxicity testing has a major significance on the concentration and speciation of released substances, further studies are needed in order to propose a relevant testing scheme.     

Ecotoxicological characterisation of 12 incineration ashes using 6 laboratory tests

In the European Waste List (2000/532/EC as amended) the ash of municipal waste incineration is defined as a so called mirror entry. This waste can be classified as hazardous or non-hazardous depending on the content of hazardous substances and other risk properties. For the assignment of waste in mirror entries, 14 criteria are defined. One of the criteria is H14 “ecotoxic”. In the presented study, the ecotoxicological potential of 12 ashes from different incineration plants has been assessed using biological test systems. The test battery included aquatic tests with eluates (algae, daphnids, and luminescent bacteria) and terrestrial tests with solid waste (plants, earthworms and bacteria). The test results revealed a clear ecotoxicological hazard potential for some of the MWI ashes. Despite the fact that fresh ashes were several times more toxic than aged ashes both groups did not differ consistently in terms of toxicity. The results show also that there is no correlation between the biological effects and the analyzed chemical compounds of the ash samples.     

Improved understanding of key elements governing the toxicity of energy ash eluates

Ash from incinerated waste consists mainly of a complex mixture of metals and other inorganic elements and should be classified based on its inherent hazardous effects according to EUs Waste Framework Directive. In a previous study, we classified eight eluates from ash materials from Swedish incineration plants, both chemically and ecotoxicologically (using bacteria, algae, crustacean and fish). Based on measured concentrations in the eluates together with literature acute toxicity data on the crustacean Nitocra spinipes we identified six elements (i.e. Zn, Cu, Pb, Al, K and Ca) potentially responsible for the observed ecotoxicity. However, comparing the used test methods with N. spinipes, the acute test was relatively insensitive to the eluates, whereas the (sub)chronic test (i.e. a partial life cycle test, investigating larval development ratio) was very sensitive. The overall aim of this follow-up study was to verify if the pinpointed elements could be responsible for the observed (sub)chronic toxicity of the eluates. Individual effect levels (i.e. NOEC values) for these six elements were therefore generated using the (sub)chronic test. Our results show that for six of the eight eluates, the observed ecotoxicity can be explained by individual elements not classified as ecotoxic (Al, K and Ca) according to chemical legislation. These elements will not be considered using summation models on elements classified as ecotoxic in solid material for the classification of H-14, but will have significant implications using ecotoxicological test methods for this purpose.     

Validation of Microtox as a first screening tool for waste classification

The Waste Framework Directive (WFD; 2008/98/EG) describes how waste materials are to be classified as hazardous or not. For complex waste materials chemical analyses are often not conclusive and the WFD provides the possibility to assess the hazardous properties by testing on the waste materials directly. As a methodology WFD refers to the protocols described in the CLP regulation (regulation on Classification, Labeling and Packaging of chemicals) but the toxicity tests on mammals are not acceptable for waste materials. The DISCRISET project was initiated to investigate the suitability of alternative toxicity tests that are already in use in pharmaceutical applications, for the toxicological hazard assessment of complex waste materials. Results indicated that Microtox was a good candidate as a first screening test in a tiered approached hazard assessment. This is now further validated in the present study. The toxic responses measured in Microtox were compared to biological responses in other bioassays for both organic and inorganic fractions of the wastes. Both fractions contribute to the toxic load of waste samples. Results show that the Microtox test is indeed a good and practical screening tool for the organic fraction. A screening threshold (ST) of 5 geq/l as the EC₅₀ value in Microtox is proposed as this ST allows to recognize highly toxic samples in the screening test. The data presented here show that the Microtox toxicity response at this ST is not only predictive for acute toxicity in other organisms but also for sub lethal toxic effects of the organic fraction. This limit value has to be further validated. For the inorganic fraction no specific biotest can be recommended as a screening test, but the use of direct toxicity assessment is also preferable for this fraction as metal speciation is an important issue to define the toxic load of elutriate fractions. A battery of 3 tests (Microtox, Daphnia and Algae) for direct toxicity assessment of this fraction is recommended in literature, but including tests for mechanistic toxicity might be useful.     

Groundwater treatment and aquatic toxicity reduction at a chemical production site

Contaminated groundwater at a chemical antioxidant and phenolic resin chemical production site was subjected to treatability studies to develop design criteria for surface water discharge. Raw groundwater required pretreatment for total suspended solids (TSS) and color removal prior to treatment by ultraviolet light/hydrogen peroxide (UV/H₂O₂). Because of high capital and operating costs for UV/H₂O₂, biological treatment was evaluated as an alternate. Respirometric analyses showed that completely mixed activated sludge could be applied as a treatment technology to the groundwater. Biotreatment resulted in an approximately 70 percent reduction in soluble chemical oxygen demand (SCOD). Residual SCOD was recalcitrant to further biodegradation. The treated effluent was tested for aquatic toxicity using fathead minnows (Pimephales promelas) and Ceriodaphnia dubia and was found to be toxic. Toxicity reduction of biotreatment effluent was evaluated in bench-scale experiments using activated carbon adsorption, filtration, and UV/H₂O₂. Subsequent toxicity testing showed that filtration alone could reduce the bioeffluent toxicity and that residual SCOD was not the primary source of toxicity.     

Ecotoxicological assessment and evaluation of a pine bark biosorbent treatment of five landfill leachates

When selecting a landfill leachate treatment method the contaminant composition of the leachate should be considered in order to obtain the most cost-effective treatment option. In this study the filter material pine bark was evaluated as a treatment for five landfill leachates originating from different cells of the same landfill in Sweden. The objective of the study was to determine the uptake, or release, of metals and dissolved organic carbon (DOC) during a leaching test using the pine bark filter material with the five different landfill leachates. Furthermore the change of toxicity after treatment was studied using a battery of aquatic bioassays assessing luminescent bacteria (Vibrio fischeri) acute toxicity (30-min Microtox®), immobility of the crustacean Daphnia magna, growth inhibition of the algae Pseudokirchneriella subcapitata and the aquatic plant Lemna minor; and genotoxicity with the bacterial Umu-C assay. The results from the toxicity tests and the chemical analysis were analyzed in a Principal Component Analysis and the toxicity of the samples before and after treatment was evaluated in a toxicity classification. The pine bark filter material reduced the concentrations of metal contaminants from the landfill leachates in the study, with some exceptions for Cu and Cd. The Zn uptake of the filter was high for heavily contaminated leachates (≥73%), although some desorption of zinc occurred in less contaminated waters. Some of the leachates may require further treatment due to discharge into a natural recipient in order to reduce the risk of possible biological effects. The difference in pH changes between the different leachates was probably due to variations in buffering capacity, affected by physicochemical properties of the leachate. The greatest desorption of phenol during filtration occurred in leachates with high conductivity or elevated levels of metals or salts. Generally, the toxicity classification of the leachates implies that although filter treatment with pine bark removes metal contaminants from the leachates effectively, it does not alter leachate toxicity noticeably. The leachates with the highest conductivity, pH and metal concentrations are most strongly correlated with an increased toxic response in the score plots of both untreated and treated leachates. This is in line with the toxicity classification of the leachate samples. The results from this study highlight the importance of evaluating treatment efficiency from the perspective of potential recipient effects, rather than in terms of residual concentrations of individual contaminants when treating waters with a complex contamination matrix, such as landfill leachates.     

Stabilization/solidification of fly ashes and concrete production from bottom and circulating ashes produced in a power plant working under mono and co-combustion conditions

Two combustion tests were performed in a fluidized bed combustor of a thermo-electric power plant: (1) combustion of coal; (2) co-combustion of coal (68.7% w/w), sewage sludge (9.2% w/w) and meat and bone meal (MBM) (22.1% w/w). Three samples of ashes (bottom, circulating and fly ashes) were collected in each combustion test. The ashes were submitted to the following assays: (a) evaluation of the leaching behaviour; (b) stabilization/solidification of fly ashes and evaluation of the leaching behaviour of the stabilized/solidified (s/s) materials; (c) production of concrete from bottom and circulating ashes. The eluates of all materials were submitted to chemical and ecotoxicological characterizations. The crude ashes have shown similar chemical and ecotoxicological properties. The s/s materials have presented compressive strengths between 25 and 40 MPa, low emission levels of metals through leaching and were classified as non-hazardous materials. The formulations of concrete have presented compressive strengths between 12 and 24 MPa. According to the Dutch Building Materials Decree, some concrete formulations can be used in both scenarios of limited moistening and without insulation, and with permanent moistening and with insulation.     

Toxicity of char residues produced in the co-pyrolysis of different wastes

Char residues produced in the co-pyrolysis of different wastes (plastics, pine biomass and used tyres) were characterized using chemical and toxicity assays. One part of the solid chars was submitted to extraction with dichloromethane (DCM) in order to reduce the toxicity of the char residues by removing organic contaminants. The different volatility fractions present in the extracted char (Char A) and in the raw char (Char B) were determined by progressive weight loss combustion. A selected group of heavy metals (Cd, Pb, Zn, Cu, Hg and As) was determined in both chars.The chars were subjected to the leaching test ISO/TS 21268 – 2, 2007 and the resulting eluates were further characterized by determining a group of inorganic parameters (pH, conductivity, Cd, Pb, Zn, Cu, Hg and As contents) and the concentrations of several organic contaminants (volatile aromatic hydrocarbons and alkyl phenols). An ecotoxicological characterization was also performed by using the bio-indicator Vibrio fischeri.The chemical and ecotoxicological results were analyzed according to the Council Decision 2003/33/CE and the criteria on the evaluation methods of waste ecotoxicity (CEMWE).The results obtained in this work indicated that the extraction with DCM is an effective method for the removal of organic contaminants of high to medium volatility from pyrolysis solid residues, thus decreasing their toxicity potential. Zn can be leached from the chars even after the DCM extraction treatment and can contribute to the ecotoxicity of the eluates obtained from chars.Both chars (treated and non treated with DCM) were classified as hazardous and ecotoxic wastes.     

Removal of Cinnamic Acid Derivatives from Aqueous Effluents by Fenton and Fenton-like Processes as an Alternative to Direct Biological Treatment

The removal of various phenolic acids (p-coumaric, caffeic and ferulic acids), typically found in wastewaters of agricultural origin, from model effluents by chemical and biological means has been investigated. Chemical oxidation processes comprising hydrogen peroxide and a homogeneous or heterogeneous copper or iron catalyst were employed over a wide range of experimental conditions. Chemical oxidation is capable of removing most of the total organic carbon initially present in the effluent at relatively mild treatment conditions (i.e. reaction times up to 120 min and temperatures up to 80°C), while removal rates generally increase with increasing temperature, H₂O₂ and catalyst concentrations. The anaerobic degradability and toxicity of p-coumaric acid has been assessed using the biochemical methane potential and anaerobic toxicity assay respectively. p-Coumaric acid, at concentrations below about 1 g/L, is not toxic against methanogens and slowly degrades over a period of about 35 days at 35°C. In light of this, chemical oxidation may provide a promising alternative to direct biological treatment for either the partial or complete removal of phenolic acids at reasonable treatment times; the implications for wastewater treatment are discussed.     

Chemical stabilization of medical waste fly ash using chelating agent and phosphates: Heavy metals and ecotoxicity evaluation

Chemical stabilization of heavy metals in medical waste fly ash has been carried out using the following compounds: a chelating agent (Ashnite S803), a commercial acidic phosphoric acid solution (Ashnite R303) as well as basic one (Ashnite R201). In order to predict the leachability of heavy metals, Japanese Leaching Test (JLT-13) procedure was applied to the stabilized fly ash products. An ecotoxicity assessment of the stabilized fly ash products leachate and the unstabilized fly ash leachate was conducted using a battery of bioassays based on lettuce root elongation inhibition, Daphnia magna mortality and Vibrio fischeri photoinhibition. The results showed that the three stabilizing agents were able to significantly decrease (ANOVA, P < 0.05) the concentration of heavy metals in the leachates. Although the leachate from both stabilized and unstabilized fly ash were very toxic to lettuce and daphnids, the incorporation of these stabilizing agents diminished significantly (ANOVA, P < 0.05) the toxicity of the leachates towards the three tested organisms. Pearson correlation analysis was used to analyze the strength of the relationship between chemical elements concentration in the leachate and bioassays results. Most of the heavy metals in the leachate were significantly correlated (ANOVA, P < 0.05) with the toxicity values of the bioassays. However, the correlation was not found between the concentration of dissolved organic carbon (DOC) and the toxicity effect of the leachate to the tested organisms.     

Acute toxicity test of leachates from traditional and sustainable landfills using luminescent bacteria

Landfilling is a fundamental step in any waste management strategy, but it can constitute a hazard for the environment for a long time. The need to protect the environment from potential landfill emissions makes risk assessment a decision tool of extreme necessity. The heterogeneity of wastes and the complexity of physical, chemical and biological processes that occur in the body of a landfill need specific procedures in order to evaluate the groundwater risk for the environment. Given the complexity of the composition of landfill leachates, the exact contribution of each potential toxic substance cannot be known precisely. Some reference contaminants that constitute the hazard (toxicity) of leachate have to be found to perform the risk assessment. A preliminary ecotoxicological investigation with luminescent bacteria has been carried out on different leachates from traditional and sustainable landfills in order to rank the chemicals that better characterize the leachate (heavy metals, ammonia and dissolved organic content). The attention has been focused on ammonia because it is present in high concentration and can last for centuries and can seriously contaminate the groundwater. The results showed that the toxicity of the leachate might reliably depend on the ammonia concentration and that the leachate toxicity is considerably lower in sustainable landfills where the ammonia had been degraded. This has an important consequence because if the containment system fails (as usually occur within 30-50yr), the risk of groundwater contamination will be calculated easier only in terms of the probability that the ammonia concentration is higher than a reference concentration.     

Investigating the Use of Iron Reducing Bacteria for the Removal of Arsenic from Contaminated Soils

Clean-up techniques, which were developed for removing cationic heavy metals from contaminated soils, are inappropriate for the metalloid As, which is a common and highly toxic pollutant. Because arsenic is mainly found associated with the hydrous ferric oxides of the soil, a possible mechanism for the mobilisation of this element is the reductive dissolution of Fe(III) oxyhydroxides. In this paper we investigate the possibility to mobilise arsenic, using the Fe(III)-reducing bacterium Desulfuromonas Palmitatis. The initial experiments were carried out using a crystalline ferric arsenate as model compound, i.e. scorodite (FeAsO₄.2H₂O). D. palmitatis was found able to reduce the trivalent iron of scorodite at a percentage of 80% within 16 days, but arsenic remained in the pentavalent state, and reprecipitated with Fe(II) in the form of low solubility ferrous arsenates. To avoid the precipitation of ferrous arsenates the subsequent experiments with soil were conducted by combining the reducing ability of D. palmitatis with the chelating strength of EDTA (ethylenediamine tetracetic acid), which can form strong aqueous complexes with Fe(II). Approximately 60% of Fe and 75% of As were recovered in the aqueous solution in the presence of EDTA, while in the simple biological treatment no Fe was dissolved and only a 3% of As was mobilised.     

An ecotoxic risk assessment of residue materials produced by the plasma pyrolysis/vitrification (PP/V) process

Plasma is the fourth state of matter, following the three states of solid, liquid and gas. Experience has amply demonstrated that solids exposed to the oxygen-deficient plasma flame are converted to liquid, and liquid exposed to the same flame is converted to gas. A low amount of vitrified solid residue material usually remains at the end of this process. Plasma pyrolysis/vitrification (PP/V) has been demonstrated as a safe, efficient, cost-effective technology for the treatment of wastes, including hazardous wastes. Besides the low amounts of gaseous byproducts that PP/V produces, the solid vitrified residue presents a low leachability of pollutants. Studies have been performed in many countries in order to assess the leachability of chemical substances. But from the results of identified studies, none has reported results on the ecotoxicological properties of the leachates. The aim of this study was to contribute to the assessment of ecotoxic risk of four different vitrified materials. Vitrified samples of contaminated soils, municipal solid wastes, and incinerator bottom ashes were submitted to the European leaching pre-standard test number prEN 12457-2. The leachates were analyzed for 22 chemical parameters. The biological characterization comprised the assessment of bioluminescence inhibition of Photobacterium phosphoreum bacterium, growth inhibition of Pseudokirchneriella subcapitata algae and the germination inhibition of Lactuca sativa vegetable. The chemical and ecotoxicological results were analyzed according to the French proposal of Criteria on the Evaluation Methods of Waste Toxicity (CEMWT) and a Toxicity Classification System (TCS). The chemical and ecotoxicological results indicated a low leachability of pollutants and a low toxicity level of leachates. All samples studied were as below the TCS class 1 level (no significant toxicity observed) and as non-ecotoxic for CEMWT. Therefore, the environmental ecotoxic risk of the analyzed vitrified samples was determined to be very low.     

Ggum-poly(Itaconic Acid) Based Superabsorbents Via Two-Step Free-Radical Aqueous Polymerization for Environmental and Antibacterial Applications

Ggum-based conducting hydrogels possessing dye removal and antibacterial property were developed by two-step free-radical aqueous polymerization method. Conductivity was introduced with polyaniline (PANI) chains incorporated within the crosslinked network of Ggum-poly(itaconic acid) superabsorbent. The material properties of the synthesized samples were characterized using FTIR spectroscopy, thermal analysis and scanning electron microscopy techniques. Results showed that synthesized samples exhibited the best antibacterial activity against Gram-positive bacteria. Synthesized samples were found to be effective in removal of toxic methylene blue (MB) dye from the waste water. The adsorption kinetics of superabsorbents has been described by using pseudo first and pseudo second order kinetics models. Furthermore, application of hydrogels to improve the water retention properties of different soils was also studied for agricultural purpose.     

Why Critical Loads of Acidity and N for Soils Should be Based on Pollutant Effective Concentrations Rather Than Deposition Fluxes

Numerous assumptions have been made over the past 17 years when calculating critical loads for soils, both for acidity (based upon base cation steady state mass balances (SMB)) and for N (eutrophication, based upon N mass balances), often without all the assumptions being explicitly stated. The tacit assumptions that the author believes to be implicit in the SMB approach are critically reviewed, with particular reference to upland regions where slope processes are highly significant. It is concluded that many of them cannot be justified, especially those that involve ignoring many key processes known to be important to biogeochemical cycling and soil evolution in upland catchments. The evidence presented suggests that critical loads of acidity and of N for soils should be based upon effective pollutant and, for acidity, also effective base cation deposition concentrations, rather than upon pollutant deposition fluxes. This is because of the dominant role of cation exchange equilibria, rather than weathering rate, in regulation of the pH and base status of the more acidification-sensitive soils, and because of the importance of transport down slope of base cations, alkalinity and N species.     

The effects of in situ chemical oxidation on microbiological processes: A review

The effects of in situ chemical oxidation (ISCO) on biological processes, as reported in the literature, were researched to determine if coupling ISCO with in situ bioremediation could be achieved in field and laboratory experiments. Literature was compiled concerning the effect of ISCO on microbial communities following addition of a chemical oxidant at a range of concentrations designed to treat a variety of subsurface contaminants. The results indicate that although microbial communities may potentially be adversely affected by chemical oxidation in the short term, a rebound of microbial biomass and/or bioremediation activity can be expected. Successfully coupling ISCO with bioremediation in field applications may be a cost‐effective method of achieving risk‐based site remediation goals. © 2006 Wiley Periodicals, Inc.     

Concentrations and Pools of Heavy Metals in Urban Soils in Stockholm,Sweden

The concentrations of heavy metals (Cd, Cr, Cu, Hg, Ni, Pb andZn) and arsenic (As) were surveyed and the metal pools estimatedin soils in Stockholm Municipality. The sampling sites were distributed all over the entire municipality with a higher sampling density in the city centre. Soils were sampled to a maximum depth of 25 to 60 cm. Soil texture, total-C content, electrical conductivity and pH were analysed. Heavy metal concentrations were determined after wet digestion with boiling7 M HNO₃.The results showed a wide range in heavy metal concentrations, as well as in other soil properties. The city centre soils constituted a rather homogeneous group whereas outside this areano geographical zones could be distinguished. These soils were grouped based on present land use, i.e. undisturbed soils, public parks, wasteland (mainly former industrial areas), and roadside soils. The city centre and wasteland soils generally hadenhanced heavy metal concentrations to at least 30 cm depth compared to park soils outside the city centre and rural (arable)soils in the region, which were used to estimate background levels. For example, the mean Hg concentration was 0.9 (max 3.3)mg kg^-1 soil at 0–5 cm and 1.0 (max 2.9) at 30 cm depth in the city centre soils, while the background level was 0,04 mg kg^-1. Corresponding values for Pb were 104 (max 444) and135 (max 339) mg kg^-1, at 0–5 and 30 cm, respectively, while the background level was 17 mg kg^-1.The average soil pools (0–30 cm depth) of Cu, Pb and Zn were 21,38 and 58 g m^-2 respectively, which for Pb was 3–4 timeshigher and for Cu and Zn 1.5–2 times higher than the backgroundlevel. The total amount of accumulated metals (down to 30 cm)in the city centre soils (4.5^*10 ⁶ m² public gardens and green areas) was estimated at 80, 1.1, 120 and 40 t for Cu, Hg, Pb and Zn, respectively. The study showed (1) thatfrom a metal contamination point of view, more homogeneous soilgroups were obtained based on present land use than on geographicdistance to the city centre, (2) the importance of establishing a background level in order to quantify the degree of contamination, and (3) soil samples has to be taken below the surface layer (and deeper than 30 cm) in order to quantify theaccumulated metal pools in urban soils.     

Environmental impact of highway construction and repair materials on surface and ground waters. Case study: crumb rubber asphalt concrete

The practice of incorporating certain waste products into highway construction and repair materials (CRMs) has become more popular. These practices have prompted the National Academy of Science, National Cooperative Highway Research Program (NCHRP) to research the possible impacts of these CRMs on the quality of surface and ground waters. State department of transportations (DOTs) are currently experimenting with use of ground tire rubber ( crumb rubber) in bituminous construction and as a crack sealer. Crumb rubber asphalt concrete (CR-AC) leachates contain a mixture of organic and metallic contaminants. Benzothiazole and 2(3H)-benzothiazolone (organic compounds used in tire rubber manufacturing) and the metals mercury and aluminum were leached in potentially harmful concentrations (exceeding toxic concentrations for aquatic toxicity tests). CR-AC leachate exhibited moderate to high toxicity for algae ( Selenastrum capriconutum) and moderate toxicity for water fleas ( Daphnia magna). Benzothiazole was readily removed from CR-AC leachate by the environmental processes of soil sorption, volatilization, and biodegradation. Metals, which do not volatilize or photochemically or biologically degrade, were removed from the leachate by soil sorption. Contaminants from CR-AC leachates are thus degraded or retarded in their transport through nearby soils and ground waters.     

Effects of oyster shell on soil chemical and biological properties and cabbage productivity as a liming materials

Oyster shell, a byproduct of shellfish-farming in Korea and containing a high amount of CaCO(3), has a high potential to be used as a liming material in agriculture. However, the agricultural utilization of oyster shell is limited due to its high concentration NaCl. The oyster-shell meal collected had a low concentration of water soluble NaCl (mean 2.7 g kg(-1)), which might be a result of stacking the material for 6 months in the open field. It has a very similar liming potential with calcium carbonate, with 3.4 and 3.8 Mg ha(-1) for silt loam (SiL, pH 6.2) and sandy loam (SL, pH 5.8) to bring the soil pH to 6.5, respectively. To determine the effect of crushed oyster-shell meal on improving soil chemical and biological properties and crop plant productivity, oyster-shell meal was applied at rates of 0, 4, 8, 12, and 16 Mg ha(-1) before transplanting Chinese cabbage (Brassica campestris L.) in the two soils mentioned above. Soil pH was significantly increased to 6.9 and 7.4 by 16 Mg ha(-1) shell meal application (4 times higher level than the recommendation) in SiL and SL, respectively, at harvesting stage. The effect of liming was found higher in SL compared to SiL soil, probably due to the different buffering capacity of the two soils. The concentration of NaCl and EC value of soils were found slightly increased with shell meal applications, but no salt damage was observed. Oyster-shell meal application increased soil organic matter, available P, and exchangeable cations concentrations. The improved soil pH and nutrient status significantly increased the microbial biomass C and N concentrations and stimulated soil enzyme activities. With the exception of acid phosphomonoesterase (PMEase) activity, which decreased with increasing soil pH in SL but slightly increased in SiL, the activities of urease and alkali PMEase increased markedly with increasing soil pH by shell meal application. The improved soil chemical and biological properties resulted in increased crop productivity. The highest yield in Chinese cabbage was achieved following the application of 8 Mg ha(-1) oyster-shell meal. Conclusively, crushed oyster shell could be used as an alternative liming material to restore the soil chemical and microbial properties in upland soil and to increase crop productivity.