改良兼氧-好氧-混凝处理碱减量印染废水

采用水解酸化-活性污泥-物化工艺联合处理含碱减量印染生活综合污水,采取预曝气、污泥回流和分级沉淀等措施,COD.去除率约为89.1%,脱色效果达86%,最终出水水质达到<纺织染整工业污染物排放标准>(GB4287-92)规定的二级排放标准.运行结果表明该工艺具有耐冲击负荷能力强,剩余污泥量少,难降解有机物去除率高等优点,在含碱减量印染废水处理中具有实用性.     

电镀六价铬废水的实用处理工艺研究及应用

研究了一种简单可行的实用型六价铬废水处理工艺.试验结果表明,采用该处理工艺,对六价铬浓度很高的电镀废水,在较短的处理时间内都能达到很好的去除效果.该工艺应用在实际工程中,六价铬去除率达99.9%以上,出水达到<污水综合排放标准>(GB 8978-1996)中的一级标准.该工艺与传统的化学处理法相比,具有操作简单、无刺激性气体排放等优点.     

厌氧水解酸化-生物接触氧化工艺处理印染废水

印染废水的色度大,有机物含量高,可生化性差。针对这些特点,采用了厌氧水解酸化-生物接触氧化、气浮等工艺处理印染废水,结果表明,该工艺对印染废水有很好的处理效果,最终出水基本无色,达到纺织染整工业水污染物排放的一级标准（GB4287--1992）,处理成本较低。     

水解酸化-好氧氧化-化学氧化-吸附工艺处理印染废水

对印染废水采用水解酸化-好氧氧化-化学氧化-吸附等进行连续处理。结果表明,该处理工艺具有废水处理效果好、出水水质稳定(出水水质达GB4287-92中的一级标准)、操作管理方便等优点,是处理印染废水的有效方法之一。     

印染废水絮凝吸附处理试验报告

印染废水处理可采用活性炭吸附、生化处理等方法。但采用这些方法处理费用昂贵,且难达到排放标准。我们采用无机——有机絮凝吸附法来处理印染废水,获得较满意的效果。现报告如下: 一、絮凝吸附理论初步探讨印染废水含有溶解染料、助剂和悬浮固体,根据悬浮固体粒子直径大小又可分为悬浮液和胶体。悬浮粒子比重越大,沉淀速度越快,并且沉淀速度与粒子     

水解酸化—铁炭微电解—好氧生化工艺处理印染废水

采用水解酸化-铁炭微电解-好氧生化工艺对印染废水进行了处理.COD为3 000～4 000 mg/L、BOD5为750～1 000 mg/L、色度为500～600倍、NH3-N为30～40 mg/L、SS为200～300 mg/L、pH为6～10的印染废水,经该工艺处理,后出水达到了<纺织染整工业水污染物排放标准>(GB 4287-92)的一级标准.运行结果表明,该工艺具有运行稳定、管理简单等优点.     

Experimental research of dyeing and printing wastewater treatment by flocculation-MBR combined technology

采用絮凝—膜生物反应器(MBR)组合工艺进行印染废水处理的试验研究.结果表明,调节pH至8.5、搅拌时间为30min时,COD和色度去除效果最佳;而单纯絮凝工艺对印染废水处理效果不理想,最佳运行条件为64 mg/L NaOH+75 mg/L饱和石灰水+0.2 mg/L聚丙烯酰胺(PAM)+3 mg/L硅酸钠+8 mg/L聚合氯化铝(PAC),COD和NH3-N平均去除率分别达到23.91％、31.17％.在上述最佳运行条件下,采用絮凝—MBR组合工艺处理印染废水,效果较显著;出水COD均值可达42.2mg/L,其平均去除率为91.62％;出水NH3-N均值可达6.26 mg/L,其平均去除率为92.43％,出水水质可达到《城镇污水处理厂污染物排放标准》(GB 18918-2002)一级B标准.     

化学絮凝—微电解脱色处理印染废水

采用化学絮凝-微电解脱色组合工艺处理扬州彩虹针织集团总厂生产过程中的印染废水,COD去除率达到83％～90％．处理后的出水清澈透明,各项指标均达到GB8978-1996《污水综合排放标准》的二级排放标准。     

采用泥回流处理彩色显像管含氟废水

本文通过中和、混凝沉降法除氟过程,研究了彩色显像管工业废水除氟的适宜工艺条件。现场试验表明:应用泥回流处理技术,采用高效絮凝剂处理含氟废水,排放废水氟含量可稳定在4-6mg/L之间,低于排放标准（10mg/L）,同时废水处理的成本大大降低。     

方便面和饮料生产废水处理技术

采用高效气浮-活性污泥法组合工艺处理方便面和饮料生产废水。工程运行实践表明，该工艺处理效果好、运行稳定。各项指标均可达到GB8978-1996《污水综合排放标准》的二级排放标准。     

Sorption and desorption of Cu and Cd by macroalgae and microalgae

The sorption and desorption of Cu and Cd by two species of brown macroalgae and five species of microalgae were studied. The two brown macroalgae, Laminaria japonica and Sargassum kjellmanianum, were found to have high capacities at pHs between 4.0 and 5.0 while for microalgae, optimum pH lay at 6.7. The presence of other cations in solution was found to reduce the sorption of the target cation, suggesting a competition for sorption sites on organisms. Sorption isotherms obeyed the Freundlich equation, suggesting involvement of a multiplicity of mechanisms and sorption sites. For the microalgae tested, Spirulina platensis had the highest capacity for Cd, followed by Nannochloropsis oculata, Phaeodactylum tricornutum, Platymonas cordifolia and Chaetoceros minutissimus. The reversibility of metal sorption by macroalgae was examined and the results show that both HCl and EDTA solutions were very effective in desorbing sorbed metal ions from macroalgae, with up to 99.5% of metals being recovered. The regenerated biomass showed undiminished sorption performance for the two metals studied, suggesting the potential of such material for use in water and wastewater treatment.     

Kinetic and structural relationships of transition monomeric and oligomeric carboxyl- and choline-esterases

The kinetic and structural relationships of eight electrophoretically pure mammalian serum and liver serine carboxylesterases (CE) and cholinesterases (ChE) have been studied. Eight CE's and ChE's, which were fully resolved but only partially purified, provided additional information. Five of the electrophoretically pure esterases were monomeric, and of these, four belonged to a new and widely distributed class. These four monomeric esterases hydrolyzed choline esters, but at widely differing rates. Thus two were termed monomeric butyrylcholinesterases, mBuChE I and II, and two were monomeric CE's (mCE). The rabbit liver mCE was not a subunit of the oligomeric CE (oCE), although the oCE also hydrolyzed choline esters at a very low rate. The complex kinetics of the mCE's, mBuChE's, oCE's, and of the oligomeric BuChE's of horse and human serum could be interpreted according to a single reaction scheme involving an allosteric site and the equation derived from it. Thus activation and inhibition at high substrate concentrations, together with sigmoidal activity versus substrate concentration plots, all of which characterize the reactions of these esterases, could be interpreted by a single scheme and equation. Structural and kinetic comparisons showed a progressive transition of properties from the oCE's through the mCE's to the oBuChE's. One of the purified mCE's was from horse serum, and it exhibited physical and kinetic properties unlike those of the liver mCE's or oCE's.     

Persistence and dissipation kinetics of trifloxystrobin and tebuconazole in onion and soil

The persistence and dissipation kinetics of trifloxystrobin and tebuconazole on onion were studied after application of their combination formulation at a standard and double dose of 75 + 150 and 150 + 300 g a.i. ha^?1. The fungicides were extracted with acetone, cleaned-up using activated charcoal (trifloxystrobin) and neutral alumina (tebuconazole). Analysis was carried out by gas chromatograph (GC) and confirmed by gas chromatograph mass spectrometry (GC-MS). The recovery was above 80% and limit of quantification (LOQ) 0.05 mg kg^?1 for both fungicides. Initial residue deposits of trifloxystrobin were 0.68 and 1.01 mg kg^?1 and tebuconazole 0.673 and 1.95 mg kg^?1 from standard and double dose treatments, respectively. Dissipation of the fungicides followed first-order kinetics and the half life of degradation was 6–6.6 days. Matured onion bulb (and field soil) harvested after 30 days was free from fungicide residues. These findings suggest recommended safe pre-harvest interval (PHI) of 14 and 25 days for spring onion consumption after treatment of Nativo 75 WG at the standard and double doses, respectively. Matured onion bulbs at harvest were free from fungicide residues.     

Bacterial and archaeal diversity in oil fields and reservoirs and their potential role in hydrocarbon recovery and bioprospecting

Environmental Science and Pollution Research - Hydrocarbon is a primary source of energy in the current urbanized society. Considering the increasing demand, worldwide oil productions are declining...     

Sorption and desorption behavior of chloroanilines and chlorophenols on montmorillonite and kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Sorption and Desorption Behavior of Chloroanilines and Chlorophenols on Montmorillonite and Kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Isocyanatocyclohexane and isothiocyanatocyclohexane levels in urban and industrial areas and possible emission-related activities

Isocyanatocyclohexane and isothiocyanatocyclohexane are becoming relevant compounds in urban and industrial air, as they are used in important amounts in automobile industry and building insulation, as well as in the manufacture of foams, rubber, paints and varnishes. Glass multi-sorbent tubes (Carbotrap, Carbopack, Carboxen) were connected to LCMA-UPC pump samplers for the retention of iso- and isothiocyanatocyclohexanes. The analysis was performed by automatic thermal desorption (ATD) coupled with capillary gas chromatography (GC)/mass spectrometry detector (MSD). TD-GC/MS was chosen as analytical method due to its versatility and the possibility of analysis of a wide range of volatility and polarity VOC in air samples. The method was satisfactory sensitive, selective and reproducible for the studied compounds. The concentrations of iso- and isothioisocyanatocyclohexanes were evaluated in different urban, residential and industrial locations from extensive VOC air quality and odour episode studies in several cities in the Northeastern edge of Spain. Around 200–300 VOC were determined qualitatively in each sample. Higher values of iso- and isothiocyanatocyclohexane were found in industrial areas than in urban or residential locations. The concentrations ranged between n.d.−246 and n.d.−29 μg m⁻³ for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively, for industrial areas. On the other hand, urban and residential locations showed concentrations ranging between n.d.−164 and n.d.−29 μg m⁻³ for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively. The site location (urban or industrial), the kind and nearness of possible iso- and isothiocyanatocyclohexane emission activities (industrial or building construction) and the changes of wind regimes throughout the year have been found the most important factors influencing the concentrations of these compounds in the different places.     

Sources and fate of PCDD and PCDF

PCDD and PCDF were found in urban air particulates from St. Louis and Washington, D.C., and in sediments from the Great Lakes and Siskiwit Lake, Isle Royale. The similarity between the PCDD and PCDF found in air particulates and sediment samples and the presence of PCDD and PCDF in sediment from Siskiwit Lake (a location which can receive only atmospheric inputs) suggest that these compounds are emitted to the atmosphere from combustion sources. The historical input of PCDD and PCDF to dated sediment cores shows a strong increase since 1940, and this suggests that the incineration of chlorinated organic compounds is an important source of PCDD and PCDF to the environment.     

Synthesis and characterization of m- and p-methylbenzyl-mercapturic acids derived from m- and p-xylenes

Chemical synthesis and physical properties of two mercapturic acids suggested as urinary metabolites of m- and p-xylenes ace described. These compounds may be used for the identification and quantivative determination by high-performance liquid chromatography of the corresponding mercapturic acids in urine.