A RATING-CURVE METHOD FOR HYDRODYNAMIC SIMULATIONS IN CONTAMINANT TRANSPORT MODELING1

ABSTRACT: Accurate prediction of hydrodynamics is of great importance to modeling contaminant transport and water quality in a river. Flow conditions are needed in estimating potential exposure contamination levels and the recovery time for a no-action alternative in contaminated sediments remediation. Considering highly meandering characteristics of the Buffalo River, New York, a three-dimensional hydrodynamic model was selected to route upstream flows through the 8-km river section with limited existing information based on the model's fully predictive capability and process-oriented feature. The model was employed to simulate changes in water depth and flow velocity with space and time in response to variation in flow rate and/or water surface elevation at boundaries for given bottom morphometry and initial conditions. Flow conditions of the river reach where historical flow data are not available were computed. A rating-curve approach was developed to meet continuous and event contaminant modeling needs. Rating curves (depth-discharge and velocity-discharge relationships) were constructed at selected stations from the 3-D hydrodynamic simulations of individual flow events. The curves were obtained as steady solutions to an unsteady problem. The rating-curve approach serves to link flow information provided by the hydrodynamic model to a contaminant transport model. With the approach, the linking problem resulting from incompatible model dimensions and grid sizes can be solved. The curves will be used to simulate sediment movement and to predict contaminant fate and transport in the river.     

A Power Law Model for River Flow Velocity in Iowa Basins

This study explores power law relationships to estimate water flow velocity as a function of discharge and drainage area across river networks. We test the model using empirical data from 214 United States (U.S.) Geological Survey gauging stations distributed over the state of Iowa in the U.S. The empirical data are the measurements of the mean cross‐sectional velocity and concurrent discharge. The data are used to estimate parameters for a state‐wide model and to test for spatial variability for 15 large river basins contained within the state. Spatial differences among the basins are small but some parameters significantly differ from the state‐wide model. Using individual station data, the authors also explore a simpler power law model that disregards dependence on the drainage area. Overall, the study shows that including drainage area improves the model. Our study provides parameter values that can be directly incorporated into a regional scale routing model, and provides a framework for developing flow velocity models for hydraulically similar rivers in the U.S. and the world.     

RECHARGE TO ALLUVIAL VALLEY AQUIFERS FROM OVERBANK FLOW AND EXCESS INFILTRATION1

ABSTRACT: Recharge is an important parameter for models that simulate water and contaminant transport in unconfined aquifers. Unfortunately, measurements of actual recharge are not usually available causing recharge to be estimated or possibly added to the calibration procedure. In this study, differences between observed water-table elevations and water-table elevations simulated with a model based on the one-dimensional Boussinesq equation were used to identify both the timing and quantity of recharge to an alluvial valley aquifer. Observed water table elevations and river stage data were recorded during a five-year period from 1991 to 1995 at the Ohio Management Systems Evaluation Area located in south-central Ohio. Direct recharge attributed to overbank flow during and shortly after flood conditions accounted for 65 percent of the total recharge computed during the five-year study period. Recharge of excess infiltration to the aquifer was intermittent and occurred soon after large rainfall events and high river stage. Specification of constant recharge with time values in ground-water simulation models seems inappropriate for stream-aquifer systems given the strong influence of the river on water table elevations in these systems.     

REGIONALIZATION OF STORM HYETOGRAPHS1

ABSTRACT: Regionalization of design storms can enhance their utility. Otherwise they have to be separately developed for different regions. Huff curves developed from point rainfall data collected at Coshocton, Ohio, and Chicago, Illinois, and from area-averaged Illinois and Texas precipitation data, are compared. The curves are similar in shape and position, with some visual differences depending on quartile. Kolmogorov-Smirnov tests showed no significant differences in moat of the comparisons. Where significant differences existed, they may not represent real differences due to the small number of storms sampled. Consequently, regionalization of Huff curves from Ohio to Illinois to Texas may be appropriate. The comparison of Huff curves is affected to an unknown degree both by the effects of area averaging of data and by basis. of-development differences. The effects of observed differences in Huff curves on watershed response variables (e.g., peak flow) requires further study.     

Generalized Nondimensional Depth‐Discharge Rating Curves Tested on Florida Streamflow1

Abstract: A discharge rating is a relationship between stage and discharge at a specific point in a river stream or lake outlet structure. Rating curves are useful for interpolating and perhaps extrapolating flow measurements and for use directly in storage routing models. However, rating data and stations are limited. A generalized nondimensional mathematical expression that describes the rating relation of depth and discharge has been developed and tested against observations from 46 stations in West‐Central Florida. Three approaches were tested in sequence to select the best fit. The proposed model is a log‐linear equation with zero intercept and a slope that fits more than 50% of the stations were analyzed. The model is normalized by the depth and discharge values at 10% exceedance from data published by the U.S. Geological Survey. For ungauged applications, Q₁₀ and d₁₀ were derived from a relationship shown to be reasonably well correlated to the watershed drainage area. The average relative error for this parameter set shows that for the flow range up to the Q₁₀ discharge, better than 30% agreement with the USGS rating data can be expected for about 50% of the stations. Further analysis is required to determine why so many stations exhibit such similar behavior and to identify the criteria or parameters governing the differences.     

River temperature sensitivity to hydraulic and meteorological parameters

A sensitivity analysis is performed to evaluate river temperature variations in response to changes in hydraulic and meteorological conditions. The effects of instream flow, river geometry, and weather factors on daily mean and daily maximum river temperatures are quantified by analytical solutions to a simplified model. The influence coefficient method is used to determine river temperature sensitivity. The sensitivity analysis presents quantitative evidence that river temperatures are more sensitive to instream flowrate, upstream inflow temperature, air temperature, humidity and solar radiation than to other parameters including wind speed and channel geometry and morphometry. It is found that the sensitivity of river temperatures to flow is as significant as that to weather. Daily maximum river temperature is more sensitive to flowrate than daily mean temperature. Adapting the concept of 'diminishing returns', a critical instream flowrate is identified, which divides high and low sensitivity of water temperatures to flowrate. The critical flowrate can be used to determine practically achievable and economically feasible flow requirements for summer river temperature control. The sensitivity results can assist in streamflow management and reservoir operation for protections of habitat and aquatic environment.     

WATER QUALITY MODELING IN THE UPPER REACHES OF THE CHOWAN RIVER1

ABSTRACT: The Chowan River system consists of three rivers in southeast Virginia that form two confluences before flowing into Albermarle Sound in North Carolina. A computer program was written to simulate flows through the river system to determine flow rates, velocities, and depths. The output of the flow program was input into a second program that calculated the concentrations of BOD₅, COD, DO, and four nitrogen parameters (organic, ammonia, nitrite-nitrate and algal-N). Measured field data were used to calibrate the model. The effect of reducing the concentration of nutrients from overland runoff on algal concentrations at the mouth of the river was studied. The program was also run to simulate the water quality of the watershed in a primitive condition, in which the watershed was assumed to consist only of forests. The results of the computer program indicate that the major changes in the water quality of the river are simulated satisfactorily. The program can be used to assess the impact of any management scheme to improve water quality.     

Modeling Monthly Fluctuations in Submersion Area of a Dammed River Reservoir: A Case Study1

Lu, Haorong, S. Samuel Li, and Jinsong Guo, 2012. Modeling Monthly Fluctuations in Submersion Area of a Dammed River Reservoir: A Case Study. Journal of the American Water Resources Association (JAWRA) 1‐13. DOI: 10.1111/jawr.12003 Abstract: Fluctuations in water submersion of the Three Gorges Reservoir in China have not been explored in spite of their important implications for shoreline erosion and other undesirable consequences. This article aims to quantify the monthly fluctuations in response to changing hydraulic parameters and regional climatic factors. Flow velocity and water levels distributed along the 609‐km long dammed river reservoir are calculated with a one‐dimensional hydrodynamics model. Evaporation of water from the surface of the reservoir is determined using mass transfer‐based methods. Calculated flow velocities and water levels compare well with field data. We show that the water surface slope decreases with rising water level at the dam, and decreases to almost zero during the winter months of water storage when the downstream water level reaches the normal pool level. The submersion area varies between 830 and 1,070 km² over the year or over 20% of the reservoir zone will experience the annual cycle of dry land and partial or complete submersion. These fluctuations are of relevance to shoreline management and to the prevention and restoration of shoreline erosion. Evaporation is estimated to fluctuate between 1,240 and 26,110 tons of water per month per kilometer length of reservoir channel; this can possibly affect the hydrological budget of the reservoir region. The simple methodologies discussed in this article can easily be applied to other dammed river reservoirs for submersion estimates.     

STREAMFLOW DEPLETION: MODELING OF REDUCED BASEFLOW ANI INDUCED STREAM INFILTRATION FROM SEASONALLY PUMPED WELLS1

ABSTRACT: Numerical modeling techniques are used to analyze streamflow depletion for stream‐aquifer systems with baseflow. The analyses calculated two flow components generated by a pumping well located at a given distance from a river that is hydraulically connected to an unconfined aquifer. The two components are induced stream infiltration and reduced baseflow; both contribute to total streamflow depletion. Simulation results suggest that the induced infiltration, the volume of water discharged from the stream to the aquifer, has a shorter term impact on streamflow, while the reduced baseflow curves show a longer term effect. The peak impacts of the two hydrologic processes on streamflow occur separately. The separate analysis helps in understanding the hydrologic interactions between stream and aquifer. Practically, it provides useful information about contaminant transport from stream to aquifer when water quality is a concern, and for areas where water quantity is an issue, the separate analysis offers additional information to the development of water resource management plan.     

Smart meters for enhanced water supply network modelling and infrastructure planning

To design water distribution network infrastructure, water utilities formulate daily demand profiles and peaking factors. However, traditional methods of developing such profiles and peaking factors, necessary to carry out water distribution network modelling, are often founded on a number of assumptions on how top-down bulk water consumption is attributed to customer connections and outdated demand information that does not reflect present consumption trends; meaning infrastructure is often unnecessarily overdesigned. The recent advent of high resolution smart water meters allows for a new novel methodology for using the continuous ‘big data’ generated by these meter fleets to create evidence-based water demand curves suitable for use in network models. To demonstrate the application of the developed method, high resolution water consumption data from households fitted with smart water meters were collected from the South East Queensland and Hervey Bay regions in Australia. Average day (AD), peak day (PD) and mean day maximum month (MDMM) demand curves, often used in water supply network modelling, were developed from the herein created methodology using both individual end-use level and hourly demand patterns from the smart meters. The resulting modelled water demand patterns for AD, PD and MDMM had morning and evening peaks occurring earlier and lower main peaks (AD: 12%; PD: 20%; MDMM: 33%) than the currently used demand profiles of the regions’ water utility. The paper concludes with a discussion on the implications of widespread smart water metering systems for enhanced water distribution infrastructure planning and management as well as the benefits to customers.     

Assessment of surface water quality of selected estuaries of Malaysia: multivariate statistical techniques

Multivariate statistical techniques such as cluster analysis (CA), factor analysis (FA) were used for the evaluation of spatial variations and the interpretation of a large complex water quality data set of two selected estuaries of Malaysia. The two locations of interest with 10 sites in each location were Kuala Juru (Juru estuary) and Bukit Tambun (Jejawi estuary). Cluster analysis showed that some sites in both locations have similar sources of pollution from point or non-point sources whereas FA yielded four factors which are responsible for water quality variations explaining more than 80% of the total variance of the data set and allowed to group the selected water quality. Correlation analysis of the data showed that some parameters have strong association with other parameters and they share a common origin source. This study illustrates the usefulness of multivariate statistical analysis for evaluation and interpretation of complex data sets to get better information about the pollution sources/factors and understanding the behavior of the parameters in water quality for effective river water quality management.     

River Channel Geometry and Rating Curve Estimation Using Height above the Nearest Drainage

River channel geometry is an important input to hydraulic and hydrologic models. Traditional approaches to quantify river geometry have involved surveyed river cross sections, which cannot be extended to ungaged basins. In this paper, we describe a method for developing a synthetic rating curve to relate flow to water level in a stream reach based on reach‐averaged channel geometry properties developed using the Height above Nearest Drainage (HAND) method. HAND uses a digital elevation model (DEM) of the terrain and computes the elevation difference between each land surface cell and the stream bed cell to which it drains. Taking increments in water level in the stream, HAND defines the inundation zone and a water depth grid within this zone, and the channel characteristics are defined from this water depth grid. We apply our method to the Blanco River (Texas) and the Tar River (North Carolina) using 10‐m terrain data from the United States Geological Survey (USGS) 3D Elevation Program (3DEP) dataset. We evaluate the method's performance by comparing the reach‐average stage‐river geometry relationships and rating curves to those from calibrated Hydrologic Engineering Center's River Analysis System (HEC‐RAS) models and USGS gage observations. The results demonstrate that after some adjustment, the river geometry information and rating curves derived from HAND using national‐coverage datasets are comparable to those obtained from hydraulic models or gage measurements. We evaluate the inundation extent and show our approach is able to capture the majority of the Federal Emergency Management Agency (FEMA) 100‐year floodplain.     

Minimum Wet‐Season Flows and Levels in Southwest Florida Rivers1

Abstract: Regulation of river flows can result in decreased stage fluctuations and alteration of inundation patterns of floodplain wetlands. However, floodplain inundation has historically not been addressed in most minimum flow determinations. Florida law requires the water management districts of the state to establish minimum flows and levels to protect water bodies from significant harm associated with water withdrawals. The Southwest Florida Water Management District utilizes a 15% reduction in habitat criterion as a threshold for defining significant harm to freshwater segments of rivers. Utilizing a multi‐parameter approach and different habitat measures for seasonal flow periods, the District has recommended minimum flow compliance standards for the Alafia, Myakka and middle Peace rivers. For the high‐flow period, the District utilized a 15% reduction in the number of days of floodplain inundation (a temporal loss) as a significant harm threshold. This approach yielded allowable flow reductions of 8% for the Alafia and Peace rivers during the high‐flow season and a 7% allowable reduction of natural flows on the Myakka River. Comparison of changes in flows associated with temporal and spatial loss thresholds indicated that flow reductions required to effect a 15% spatial loss of habitat on the Alafia, Myakka and middle Peace rivers are higher than those that would yield a 15% temporal loss. This indicates that with respect to natural flow protection, the District’s consideration of temporal reductions in habitat for establishing minimum river flows for seasonal high‐flow periods is more conservative than the use of a spatial loss criterion.     

Changes in Hydrology of the Ganges Delta of Bangladesh and Corresponding Impacts on Water Resources

The Ganges Delta in Bangladesh is an example of water‐related catastrophes in a major rural river basin where limitations in quantity, quality, and timing of available water are producing disastrous conditions. Water availability limitations are modifying the hydrologic characteristics especially when water allocation is controlled from the upstream Farakka Barrage. This study presents the changes and consequences in the hydrologic regime due to climate‐ and human‐induced stresses. Flow duration curves (FDCs), rainfall elasticity, and temperature sensitivity were used to assess the pre‐ and post‐barrage water flow patterns. Hydrologic and climate indices were computed to provide insight on hydro‐climatic variability and trend. Significant increases in temperature, evapotranspiration, hot days, heating, and cooling degree days indicate the region is heading toward a warmer climate. Moreover, increase in high‐intensity rainfall of short duration is making the region prone to extreme floods. FDCs depict a large reduction in river flows between pre‐ and post‐barrage periods, resulting in lower water storage capacity. The reduction in freshwater flow increased the extent and intensity of salinity intrusion. This freshwater scarcity is reducing livelihood options considerably and indirectly forcing population migration from the delta region. Understanding the causes and directions of hydrologic changes is essential to formulate improve water resources management in the region.     

OPTICAL CHARACTERISTICS OF NEW ZEALAND RIVERS IN RELATION TO FLOW1

ABSTRACT: Six years (1989–1994) of data from New Zealand's National Rivers Water Quality Network were used to characterize the optical water quality regime of river waters as regards: visual clarity (black disc visibility), turbidity, and light-absorbing aquatic humic material (referred to as ‘yellow substance,’ measured as light absorption at 440 nm). Quantitative relationships between optical water quality variables and flow in rivers are well-described by power law expressions. Visual clarity usually decreases strongly with increasing flow in individual rivers. There is a strong, inverse relationship between turbidity and visibility, but, because of differences between sites, turbidity is not a good general predictor of visual clarity (the attribute of real interest) in rivers. Yellow substance tends to increase with increasing flow, probably because during rainstorms, soil water high in yellow-colored humic material, rather than rain water or ground water, dominates discharge. Therefore, rivers are typically clear and low in humic matter at low flow, and turbid and yellow-colored at high flow.     

沿海油田污染物入海通量及优化管理

胜利油田所在的黄河三角洲诸条河流按入海类型分为三种形式：设有防潮闸的感潮河；设有排涝站的入海河；直流入海的感潮河。按照各河流入海段面、流速、流量和水体污染物浓度，建立起各种感潮河污染物入海通量模式，计算结果说明沿海油田排放的石油类污染物入海通量为1456t／a，COD入海量为5720t／a。根据各条入海河流不同功能和污染物入海量，按照国家地表水质标准，制定出入海河流环境组合目标，用总量控制方法提出污染源削减要求，以保证黄河三角洲沿海滩涂环境质量。并以污染物入海通量、河流径流量、污染物自净系数和污染物削减量等因子建立各条河流优化管理模型，为保护环境提供对策。     

WATER QUALITY MANAGEMENT OF SKUDAI RIVER1

ABSTRACT: Urban runoff as well as industrial and agricultural discharges have seriously affected the water quality of the Skudai River, Malaysia. A water quality model is developed for simulating BOD and oxygen relationship. The simulated values agree relatively well with survey data taken during low flow conditions. Survey and simulated values show that a pollution abatement program is needed to prevent further deterioration of the river from organic discharges. A systems approach, involving complete analysis of water quality models and environmental control procedures, considering various water use patterns, water quality criteria, and waste input, is essential for solution.     

Model‐Based Nitrogen and Phosphorus (Nutrient) Criteria for Large Temperate Rivers: 1. Model Development and Application

An initial inquiry into model‐based numeric nitrogen and phosphorus (nutrient) criteria for large rivers is presented. Field data collection and associated modeling were conducted on a segment of the lower Yellowstone River in the northwestern United States to assess the feasibility of deriving numeric nutrient criteria using mechanistic water‐quality models. The steady‐state one‐dimensional model QUAL2K and a transect‐based companion model AT2K were calibrated and confirmed against low‐flow conditions at a time when river loadings, water column chemistry, and diurnal indicators were approximately steady state. Predictive simulation was then implemented via nutrient perturbation to evaluate the steady‐state and diurnal response of the river to incremental nutrient additions. In this first part of a two‐part series, we detail our modeling approach, model selection, calibration and confirmation, sensitivity analysis, model outcomes, and associated uncertainty. In the second part (Suplee et al., 2015) we describe the criteria development process using the tools described herein. Both articles provide a fundamental understanding of the process required to develop site‐specific numeric nutrient criteria using models in applied regulatory settings.     

PARAMETER ESTIMATES FOR A GROUND WATER MODEL1

ABSTRACT: This paper presents a parameter sensitivity study of a two-dimensional flow and transport model of a contaminated site. Hydrogeological and site data from previous investigations were used for calibration. The USGS contaminant transport model (MOC) was used. After flow calibration to establish a reference model, parameters were varied to examine the effect each had on predictions of a contaminant plume. Hydrogeological parameters and a step size parameter were incrementally varied individually. Each result was compared to the reference model output to evaluate changes in concentration values and contaminant plume configuration. The study indicated that a generally predictable trend can be established for some parameters not affected by pumping or similar high stresses. Ranges were identified to relate concentration error or plume change to the amount of parameter error. Some parameter perturbations produced distorted model responses at high stress locations. Porosity and anisotropy were found to be the most influential of the model parameters studied on the plume predictions. (KEY TERMS: ground water hydrology; hydrogeology; pollution modeling; water quality; model calibration.)     

SEDIMENT TRANSPORT IN A SHALLOW COASTAL ESTUARY DURING THE WINTER SEASON1

ABSTRACT: This project analyzes suspended sediment flux through the upper Barataria basin in Louisiana during the winter season defined from November through April. The Barataria is a shallow coastal estuary located in southeastern Louisiana. The controls exerted by environmental parameters (such as wind or atmospheric pressure) in wetlands‐shallow bay ecosystems on transport of water and sediment were examined. Water samples were taken at a bayou (which serve as the inlet for flow to the estuary) on a regular basis. These samples were analyzed for total suspended solids and volatile suspended solids. Velocity, depth, temperature, salinity, conductivity, and meteorological measurements were all recorded at the time of each sampling. A multi‐parameter field probe was employed to continually monitor turbidity, water level, conductivity, and temperature during frontal events. These data were used in a regression analysis to examine the factors that drive carbon flux in the region. Investigations have determined that synoptic climate and prevailing weather conditions explain much of the variations in water levels, flow circulation patterns, salinity, and suspended sediment. Relatively small amounts of sediment appear to leave the estuary during normal tidal activity, but winter storm fronts result in significant fluxes of sediment in both up‐basin and down‐basin directions.