ESTIMATED RUNOFF FROM MAN-MADE SNOW1

ABSTRACT: The consumptive loss from man-made snowmaking at six Colorado ski areas is calculated. The focus of the procedures in this investigation is on the consumptive loss that occurs to man-made snow particles during the period they reside on or in the snowpack until spring snowmelt (termed the watershed loss). Calculated watershed losses under a variety of precipitation and temperature conditions at six ski areas varied from 7 to 33 percent. These calculations were made using the calibrated Subalpine Water Balance Simulation Model (Leaf and Brink, 1973a, 1973b). The watershed loss of 7 to 33 percent indicates the range of likely watershed losses that can be expected at Colorado ski areas. A previous paper by the authors (Eisel et al., 1988) provided estimates of the mean consumptive loss during the snowmaking process (termed initial loss) for conditions existing at Colorado ski areas to be 6 percent of water applied. Therefore, based on the mean initial loss, the total consumptive loss from man-made snowmaking under conditions found at Colorado ski areas could be expected to range from 13 to 37 percent. These results demonstrate the range of total consumptive losses that could be expected in various years and for various watershed conditions. These total percentage losses cannot be extrapolated directly to other specific sites because the total consumptive loss is dependent on temperature during actual snowmaking, temperature and precipitation throughout the winter at the specific ski area, and watershed conditions at the ski area. Consumptive losses to man-made snow for a specific ski area should be estimated using the handbook procedures developed especially for this purpose (Colorado Ski Country USA, 1986b).     

AN EMPIRICALLY‐BASED SEQUENTIAL GROUND WATER MONITORING NETWORK DESIGN PROCEDURE1

ABSTRACT: A procedure using a simple, empirically‐based model that makes efficient use of available information has been developed for designing a ground water monitoring well network. A moving plume is described by siting wells in a sequential manner, relying upon two‐dimensional concentration data obtained from previously installed wells to determine the locations of future wells. Data sets from two well known, densely monitored natural gradient tracer studies were used to test the procedure. Plumes defined by all information in the original networks were compared to those defined by reduced networks designed by the new procedure. The new procedure tracked the plumes using only a portion of that information. The new procedure could have reduced the number of wells in the original tests by about 50 percent without appreciable loss of plume information as measured by plume location and extent and by tracer mass.     

APPLICATION OF THE GREEN-AMPT INFILTRATION EQUATION TO WATERSHED MODELING1

ABSTRACT: A computer model was developed, based on the Green-Ampt infiltration equation, to computed rainfall excess for a single precipitation event. The model requires an estimate of parameters related to hydraulic conductivity, wetting front section, and fillable porosity of the soil layers. Values of parameters were estimated from soil textural averages or regression equations based on percent sand, percent clay, and porosity. Average values of effective porosity and wetting front suction were largely acceptable due to the relatively low variability and low model sensitivity to the parameters. Hydraulic conductivity was the most erratic constituent of the loss rate computation due to the high variability and the high sensitivity of the computed infiltration to the parameter. The performance of the Green-Ampt infiltration model was tested through a comparison with the SCS curve number procedure. Seven watersheds and 23 storms with precipitation of one inch or greater were used in the comparison. For storms with less than one inch of rainfall excess, the SCS curve number procedure generally gave the best results; however, for six of the seven storms with precipitation excess greater than one inch, the Green-Ampt procedure delivered better results. In this comparison, both procedures used the same initial abstractions. The separation of rainfall losses into infiltration, interception, and surface retention is, in theory, an accurate method of estimating precipitation excess. In the second phase of the study using nine watersheds and 39 storms, interception and surface retention losses were computed by the Horton equations. Green-Ampt and interception parameters were estimated from value sin the literature, while the surface retention parameter was calibrated so that the computed runoff volumes matched observed volumes. A relationship was found between the surface retention storage capacity and the 15-day antecedent precipitation index, month of year, and precipitation amount.     

SWMHMS - SMALL WATERSHED MONTHLY HYDROLOGIC MODELING SYSTEM1

ABSTRACT: SWMHMS is a conceptual computer modeling program developed to simulate monthly runoff from a small nonurban watershed. The input needed to run model simulations include daily precipitation, monthly data for evapotranspiration determination (average temperature, crop consumptive coefficients, and percent daylight hours), and six watershed parameter values. Evapotranspiration was calculated with the Blaney-Criddle equation while surface runoff was determined using the Soil Conservation Service curve number procedure. For watershed parameter evaluation, SWMHMS provides options for both optimization and sensitivity analysis. Observed runoff data are required along with the model input previously mentioned in order to conduct parameter optimization. SWMEIMS was tested with data from six watersheds located in different regions of the United States. Model accuracy was generally found to be very good except on watersheds having substantial snowfall accumulation. In having only six watershed parameters, SWMHMS is less complex to use than many other computer programs that calculate monthly runoff. Consequently, SWMHMS may find its greatest application as an educational tool for students learning principles of hydrologic modeling, such as parameter evaluation procedures and the impacts of input data uncertainty on model results.     

HYDROLOGIC AND ECONOMIC IMPACTS OF DROUGHT UNDER ALTERNATWE POLICY RESPONSES1

ABSTRACT: A severe sustained drought in the Colorado River Basin would cause economic damages throughout the Basin. An integrated hydrologic-economic-institutional model introduced here shows that consumptive water users in headwaters states are particularly vulnerable to very large shortfalls and hence large damages because their rights are effectively junior to downstream users. Chronic shortfalls to consumptive users relying on diversions in excess of rights under the Colorado River Compact are also possible. Nonconsumptive water uses (for hydropower and recreation) are severely affected during the worst drought years as instream flows are reduced and reservoirs are depleted. Damages to these uses exceeds those to consumptive uses, with the value of lost hydropower production the single largest economic impact of a severe sustained drought. Modeling of alternative policy responses to drought suggests three general policy approaches with particular promise for reducing damages. Consumptive use damages can be reduced by over 90 percent through reallocation from low to high valued uses and through reservoir storage strategies which minimize evaporation losses. Reservoir management to preserve minimum power pool levels for hydropower production (and to maintain reservoir recreation) may reduce damages to these nonconsumptive uses by over 30 percent, but it may increase consumptive use shortfalls.     

EVAPOTRANSPIRATION AND CANOPY RESISTANCE AT AN UNDEVELOPED PRAIRIE IN A HUMID SUBTROPICAL CLIMATE1

ABSTRACT: Reliable estimates of evapotranspiration from areas of wildland vegetation are needed for many types of water-resource investigations. However, little is known about surface fluxes from many areally important vegetation types, and relatively few comparisons have been made to examine how well evapotranspiration models can predict evapotranspiration for soil-, climate-, or vegetation-types that differ from those under which the models have been calibrated. In this investigation at a prairie site in west-central Florida, latent heat flux (λE) computed from the energy balance and alternatively by eddy covariance during a 15-month period differed by 4 percent and 7 percent on hourly and daily time scales, respectively. Annual evapotranspiration computed from the energy balance and by eddy covariance were 978 and 944 mm, respectively. An hourly Penman-Monteith (PM) evapotranspiration model with stomatal control predicated on water-vapor-pressure deficit at canopy level, incoming solar radiation intensity, and soil water deficit was developed and calibrated using surface fluxes from eddy covariance. Model-predicted λE agreed closely with λE computed from the energy balance except when moisture from dew or precipitation covered vegetation surfaces. Finally, an hourly PM model developed for an Amazonian pasture predicted λE for the Florida prairie with unexpected reliability. Additional comparisons of PM-type models that have been developed for differing types of short vegetation could aid in assessing interchangeability of such models.     

COMBINED SEWER OVERFLOW CONTROL THROUGH IN-RECEWING WATER STORAGE: AN EFFICIENCY EVALUATION1

ABSTRACT: A demonstration and efficiency evaluation project was conducted for the flow balancing method (FBM) facility, a combined sewer overflow (CSO) storage facility at Fresh Creek in Brooklyn, New York City. The FBM is a curtained tank located directly in the receiving water that captures CSO. The CSO floats on top of and displaces Fresh Creek saltwater before it is pumped back to the publicly owned treatment works (POTW). The facility was a pilot scale subject to the full CSOs. The purpose of the project was to show how the FBM can withstand severe weather and tidal conditions and to develop a procedure for estimating CSO control efficiency (percentage of CSO pumped back to the POTW). The procedure proved successful and incorporated specific conductivity as a tracer in mass balance equations. These equations provided estimates of the net percent, capture-pumpback of the CSO using the FBM, including the amount of Fresh Creek water that was included in the pumpback to the P01W. The efficiency was directly related to the volume of the CSO and the pumpback rate and ranged from a low of 3.3 percent for the largest event to a high of 76.9 percent for the smallest event. Recent FBM enlargement should result in substantial increases in CSO control. The FBM facility has operated successfully for over five years, withstanding ice storms, near hurricane force winds and up to 7 ft tidal range.     

CONTINENTAL SCALE SIMULATION OF THE HYDROLOGIC BALANCE1

This paper describes the application of a continuous daily water balance model called SWAT (Soil and Water Assessment Tool) for the conterminous U.S. The local water balance is represented by four control volumes; (1) snow, (2) soil profile, (3) shallow aquifer, and (4) deep aquifer. The components of the water balance are simulated using “storage” models and readily available input parameters. All the required databases (soils, landuse, and topography) were assembled for the conterminous U.S. at 1:250,000 scale. A GIS interface was utilized to automate the assembly of the model input files from map layers and relational databases. The hydrologic balance for each soil association polygon (78,863 nationwide) was simulated without calibration for 20 years using dominant soil and land use properties. The model was validated by comparing simulated average annual runoff with long term average annual runoff from USGS stream gage records. Results indicate over 45 percent of the modeled U.S. are within 50 mm of measured, and 18 percent are within 10 mm without calibration. The model tended to under predict runoff in mountain areas due to lack of climate stations at high elevations. Given the limitations of the study, (i.e., spatial resolution of the data bases and model simplicity), the results show that the large scale hydrologic balance can be realistically simulated using a continuous water balance model.     

A water network optimization using MATLAB—A case study

The methodology of mass and energy integration is widely applied for reduction of water consumption, which belongs to the area of mass integration, and is also energy integration problem if water is considered an energy source (cooling water and steam). This work presents a study of water-consumption reduction through optimization of the process superstructure. A petroleum refinery water network was analyzed and a solution is proposed to minimize the costs of fresh water and wastewater treatment. Three processes which use water, with three contaminants, were monitored and three potential treatment units are proposed. The procedure was based on relaxation of a non-convex non-linear programming problem into a mixed integer linear programming (MILP). The MILP model was further simplified using heuristic rules and solved by using MATLAB.     

Automated Calibration of the METRIC‐Landsat Evapotranspiration Process

A remaining challenge to applying satellite‐based energy‐balance algorithms for operational estimation of evapotranspiration (ET) is the calibration of the energy‐balance model. Customized calibration for each image date is generally required to overcome biases associated with radiometric accuracy of the image, uncertainties in aerodynamic features of the landscape, background thermal conditions, and model assumptions. The CIMEC process (calibration using inverse modeling at extreme conditions) is an endpoint calibration procedure where near extreme conditions in the image are identified where the ET can be estimated and assigned. In the Mapping EvapoTranspiration at high Resolution with Internalized Calibration (METRIC?) energy‐balance model, two endpoints represent the dry and wet ends of the ET spectrum. Generally, user‐intervention is required to select locations in the image to produce best accuracy. To bring the METRIC and similar processes into the domain of less experienced operators, a consistent, reproducible, and dependable statistics‐based procedure is introduced where relationships between vegetation amount and surface temperature are used to identify a subpopulation of locations (pixels) in an image that may best represent the calibration endpoints. This article describes the background and logic for the statistical approach, how the statistics were developed, area of interest requirements and assumptions, adjustment for dry conditions in desert climates, and implementation in a common image processing environment (ERDAS Imagine).     

CONSUMPTIVE USE OF STREAMFLOW INCREASES IN THE COLORADO RIVER BASIN1

ABSTRACT: This study examined the disposition of streamflow increases that could be created by vegetation management on forest land along the upper reaches of the Colorado River. A network optimization model was used to simulate water flow, storage, consumptive use, and loss within the entire Colorado River Basin with and without the flow increases, according to various scenarios incorporating both current and future consumptive use levels as well as existing and potential institutional constraints. Results indicate that very little of the flow increases would be consumptively used at current use levels, or even at future use levels, if water allocation institutions remain unchanged. Given future use levels and economically based water allocation institutions, up to one-half of the flow increases could be consumptively used. The timing of streamflow increases, and the institutional constraints on water allocation, often limit the potential for consumptive use of flow increases.     

A REMOTE SENSING APPROACH FOR MODELING WATER RESOURCE USE1

Remote sensing data combined with other spatially referenced data were used to predict water resource use in an irrigated area of Central Oregon. Crop type and irrigation method were determined using color infrared aerial photography and thermal infrared imagery, respectively. These data were combined with crop consumptive use and irrigation method application efficiency values to determine total water applied to a transect sample through the heart of the study area. This information, when integrated with data on canal leakage and storage reservoir seepage, allowed the researcher to predict total water use for the entire management unit. The model developed allowed the researcher to attain results accurate to within 92.0 percent of actual values, suggesting that predictive water use models which use such techniques have tremendous potential for providing water resource managers with near real-time statistics required for making wise management decisions.     

MANAGEMENT OF FLOOD CONTROL SUMPS AND POLLUTANT TRANSPORT1

ABSTRACT: Levee sump systems are used by many riverine communities for temporary storage of urban wet weather flows. The hydrologic performance and transport of stormwater pollutants in sump systems, however, have not been systematically studied. The objective of this paper is to present a case study to demonstrate development and application of a procedure for assessing the hydraulic performance of flood control sumps in an urban watershed. Two sumps of highly variable physical and hydraulic characteristics were selected for analysis. A hydrologic modeling package was used to estimate the flow hydrograph for each outfall as part of the flow balance for the sump. To validate these results, a water balance was used to estimate the total runoff using sump operational data. The hydrologic model calculations provide a satisfactory estimate of the total runoff and its time‐distribution to the sump. The model was then used to estimate pollutant loads to the sump and to the river. Although flow of stormwater through a sump system is regulated solely by flood‐control requirements, these sumps may function as sedimentation basins that provide purification of stormwater. A sample calculation of removals of several conventional pollutants in the target sumps using a mass balance approach is presented.     

WATER MANAGEMENT AND N,P LOSSES FROM PADDY FIELDS IN SOUTHERN KOREA1

ABSTRACT: Assessment and control of nutrient losses from paddy fields is important to protect water quality of lakes and streams in Korea. A four‐year field study was carried out to investigate water management practices and losses of nitrogen (N) and phosphorus (P) in rice paddy irrigation fields in southern Korea. The amount and water quality of rainfall, irrigation, surface drainage, and infiltration were measured and analyzed to estimate inputs and losses of N and P. The observed irrigation amount surpassed consumptive use, and approximately 52 to 69 percent of inflow (precipitation plus irrigation) was lost to surface drainage. Field data showed that significant amounts of irrigation water and rainfall were not effectively used for rice paddy culture. Water quality data indicated that drainage from paddy fields could degrade the recipient water environment. The nutrient balance indicated that significant amounts of nutrients (29.5 percent of total N and 8.6 percent of total P compared to input) were lost through surface drainage. Furthermore, up to half the nutrient losses occurred during nonstorm periods. The study results indicate that inadequate water management influences N and P losses during both storm and nonstorm periods. Proper water management is required to reduce nutrient losses through surface drainage from paddy fields; this includes such measures as minimum irrigation, effective use of rainfall, adoption of proper drainage outlet structures, and minimized forced surface drainage.     

IDENTIFICATION OF AQUIFER DISPERSIVITIES: METHODS OF ANALYSIS AND PARAMETER UNCERTAINTY1

ABSTRACT: This paper presents a method for estimating aquifer dispersivities in solute transport models. Sensitivity equations are derived for the calculation of sensitivity coefficients. A modified Gauss-Newton algorithm is used to perform the least-squares minimization. A statistical procedure is outlined to assess reliability of the estimated parameters. The solute transport model is solved by the upstream weighted, multiple cell balance method which combines the concepts of local mass balance and finite element approximations. A one-dimensional solute transport problem in a vertical column system is first used to illustrate the inverse technique. A second example considers the parameter identification problem for three-dimensional solute transport with a unidirectional steady and uniform flow field. The third example solves the parameter identification problem in a three-dimensional, stream-aquifer, solute transport system with steady state flow. Numerical experiments are conducted to study data requirements for parameter identification.     

LABORATORY AND NUMERICAL INVESTIGATION OF LONGITUDINAL DISPERSION IN OPEN CHANNELS1

ABSTRACT: The non-Fickian nature of the longitudinal dispersion in natural channels during low flow has been investigated using both laboratory experiments and the numerical solution of the proposed mathematical model which is based on a set of mass balance equations describing the dispersion and mass exchange mechanisms. Laboratory experiments, which involved collection of channel geometry, hydraulic, and dye dispersion test data, were conducted to obtain sets of experimental data on a model of four pool and riffle sequences in a 161-ft long tilting flume in the Hydrosystems Laboratory at the University of Illinois at Urbana-Champaign. The experimental results indicate that flow over the model pool-riffle sequences is highly nonuniform. Concentration-time curves are significantly skewed with long tails. The mixing and dispersion in the laboratory channel was simulated using a numerical solution of the mathematical model in which the finite difference method developed by Stone and Brian (1963) was used as a solution technique. The comparison between measured and predicted concentration-time curves shows that there is a good level of agreement in the general shape, peak concentration, and time to peak. The proposed model shows significant improvement over the conventional Fickian model in predicting dispersion processes in natural channels under low flow conditions.     

ESTIMATION OF ENERGY REQUIREMENTS OF MORNING DEW EVAPORATION FROM LEAF SURFACES1

ABSTRACT: Evapotranspiration from vegetation is generally computed without consideration for early morning energy loss involved in drying wet leaf surfaces. In humid areas where dew formation is frequent, estimation of energy requirements for evaporating dew should be of interest. In this study, sensible heat flux (H) was computed from wind and temperature profile measurements over the study site. A leaf wetness sensor was used to measure the duration of evaporation from an exposed leaf surface, and net radiation was measured with a radiometer. The energy flux during the period of wet leaf surface evaporation was integrated over time. A cattail lysimeter situated at the site indicated the time when evapotranspiration started after wet leaves were dry. The energy requirements to dry an exposed wet leaf surface was estimated using energy balance methods. The mean value based on 44 days of observations from mid February to early May of 1993 indicates that the energy required to evaporate dew from openly exposed wet leaves was 5 percent of the total daily evapotranspiration of cattails with a coefficient of variation of 0.72. The mean time required to evaporate dew from exposed leaf surfaces from the onset of positive net radiation was 78 minutes. The mean dew evaporation in a morning from an exposed leaf surface was 0.16 mm with a maximum value of 0.41 mm. The energy required to dry wet leaves is a factor that should be considered when modeling evapotranspiration at hourly or shorter time intervals. Also, physical evapotranspiration models need to account for energy requirements for drying dew and rainfall wetted leaves.     

EVALUATION OF SELECTED PESTICIDES IN NORTH CAROLINA SURFACE WATER SUPPLIES: INTAKE STUDY1

ABSTRACT: Studies were conducted to analyze the presence of 11 selected pesticides in 12 surface water supply intakes in the Piedmont and coastal plain regions of North Carolina. Samples were assayed using enzyme linked immunosorbent assays (ELISAs). Samples with pesticide detection of 1 μg/L or greater were extracted and confirmed using gas chromatography/mass spectrometry (GC/MS). Detection limits of the immunosorbent assays for pesticide residues were generally an order of magnitude higher than GC/MS. Atrazine was detected in approximately 45 percent of the samples, and on two occasions was at or above the lifetime Maximum Contaminant Level of 3.0 μg/L set by the Environmental Protection Agency for an annual average in finished drinking water. Metolachlor was detected in 58 percent of the samples. Of the remaining nine pesticides, including carbaryl, aldicarb, 2,4‐D, chiorpyrifos, acetochlor, methomyl, carbofuran, alachlor, and chlorothalonil, only aldicarb, 2,4‐D, and chlorpyrifos were detected in less than 9 percent of the samples for each pesticide.     

QUANTIFICATION OF THE WATER BUDGET AND NUTRIENT LOADING IN A SMALL PEATLAND1

ABSTRACT: Few water budgets exist for specific types of wetlands such as peatlands, even though such information provides the basis from which to investigate linkages between wetlands and upland ecosystems. In this study, we first determined the water budget and then estimated nutrient loading from an upland farm field into a 1.5 ha, kettle-block peatland. The wetland contains highly anisotropic peat and has no distinct, active layer of groundwater flow. We estimated the depth of the active layer using Fick's law of diffusion and quantified groundwater flow using a chemical mass balance model. Evapotranspiration was determined using MORECS, a semi-physical model based on the Penman-Monteith approach. Precipitation and surface outflow were measured using physical means. Groundwater provided the major inflow, 84 percent (44,418 m³) in 1993 and 88 percent (68,311 m³) in 1994. Surface outflow represented 54 percent (28,763 m³) of total outflows in 1993 and 48 percent (37,078 m³) in 1994. A comparison of several published water budgets for wetlands and lakes showed that error estimates for hydrologic components in this study are well within the range of error estimates calculated in other studies. Groundwater inflow estimates and nutrient concentrations of three springs were used to estimate agricultural nutrient loading to the site. During the study period, nutrient loading into the peatland via groundwater discharge averaged 24.74 kg K ha^-1, 1.83 kg total inorganic P ha^d, and 21.81 kg NO₃-N ha^-1.     

Capacity of biochar application to maintain energy crop productivity: soil chemistry, sorghum growth, and runoff water quality effects

Pyrolysis of crop biomass generates a by-product, biochar, which can be recycled to sustain nutrient and organic C concentrations in biomass production fields. We evaluated effects of biochar rate and application method on soil properties, nutrient balance, biomass production, and water quality. Three replications of eight sorghum [ (L.) Moench] treatments were installed in box lysimeters under greenhouse conditions. Treatments comprised increasing rates (0, 1.5, and 3.0 Mg ha) of topdressed or incorporated biochar supplemented with N fertilizer or N, P, and K fertilizer. Simulated rain was applied at 21 and 34 d after planting, and mass runoff loss of N, P, and K was measured. A mass balance of total N, P, and K was performed after 45 d. Returning 3.0 Mg ha of biochar did not affect sorghum biomass, soil total, or Mehlich-3-extractable nutrients compared to control soil. Yet, biochar contributed to increased concentration of dissolved reactive phosphorus (DRP) and mass loss of total phosphorus (TP) in simulated runoff, especially if topdressed. It was estimated that up to 20% of TP in topdressed biochar was lost in surface runoff after two rain events. Poor recovery of nutrients during pyrolysis and excessive runoff loss of nutrients for topdressed biochar, especially K, resulted in negative nutrient balances. Efforts to conserve nutrients during pyrolysis and incorporation of biochar at rates derived from annual biomass yields will be necessary for biochar use in sustainable energy crop production.