Size distributions of airborne microbes in moisture-damaged and reference school buildings of two construction types

Any risk assessment of moisture-damaged buildings requires an accurate characterization of the factors contributing to the human exposure. In this study, the size distributions of indoor air viable fungi and bacteria and average mean diameters of the most common fungi in school buildings were determined. One special focus was to analyze how the microbial size distributions are affected by the building frame (either wooden or concrete) and moisture damage in the building. The study was performed in 32 school buildings classified as moisture-damaged (index) and non-damaged (reference) schools according to technical building investigations. Sampling for indoor air microbes was carried out using a cascade impactor that collects particles on six stages (range from 0.65 to >7 μm) according to their aerodynamic diameters. Both wooden and concrete schools had their highest fungal levels in the size range of 1.1–4.7 μm. However, the concentrations of fungi in all size classes were higher in wooden schools than in concrete schools. Moisture damage-associated differences in size distribution, in the particle size range of 1.1–2.1 μm, were seen in concrete schools but not in wooden schools. In general, the average geometric mean diameter (d_g,ave) of total viable fungi was smaller in wooden schools than in concrete schools, and smaller in index schools of both construction types than in their reference schools. Variation in particle size, however, by genus was observed. No differences in particle size distributions of viable airborne bacteria were found. Our results on the dependency of the particle size on the building type and presence of moisture damage provide an interesting point to be considered in assessing the complex issue of indoor-related bioaerosol exposures.     

Size distributions and formation of dicarboxylic acids in atmospheric particles

The PM2.5 concentrations and the size distributions of dicarboxylic acids in Hong Kong were studied. Eleven sets of daily PM2.5 samples were obtained at a downtown sampling site during the period of 5–16 December 2000 using an R&P speciation PM2.5 sampler. About 6–12% of the total oxalic acid was found in the gas phase in some samples. A good correlation between succinate and sulfate (R²=0.88) and a moderate correlation between oxalate and sulfate (R²=0.74) were found. Sampling artifacts of oxalate, malonate and succinate were found to be negligible. A total of 18 sets of 48–96 h size distribution data on dicarboxylic acids, sulfate, nitrate and sodium at an urban site and a rural site from June 2000 to May 2001 were obtained using a Micro-Orifice Uniform Deposit Impactor. Data from both sites show similar size distribution characteristics of the dicarboxylic acids. The condensation mode of oxalate was usually observed at 0.177–0.32 μm. The location of the peak of the droplet mode of oxalate was associated with that of sulfate. When the peak of sulfate in the droplet mode appeared at 0.32–0.54 μm, the peak of oxalate sometimes appeared at 0.32–0.54 μm and sometimes shifted to 0.54–1.0 μm. When the peak of sulfate in the droplet mode appeared at 0.54–1.0 μm, the peak of oxalate sometimes appeared at 0.54–1.0 μm and sometimes shifted to 1.0–1.8 μm. Oxalate, succinate and sulfate found in the droplet mode were attributed to in-cloud formation. The slight shift of the oxalate peak from 0.32–0.54 to 0.54–1.0 μm or from 0.54–1.0 to 1.0–1.8 μm was ascribed to minor oxalate evaporation after in-cloud formation. The maximum peak of malonate sometimes appeared in the droplet mode and sometimes appeared at 3.1–6.2 μm. The formation of malonate is associated to the reactions between sea salt and malonic acid.     

Size and seasonal distributions of airborne bioaerosols in commuting trains

Aerobiological studies in commuting trains in northern Taiwan were carried out from August, 2007 until July, 2008. Two six-stage (>7 μm, 4.7～7 μm, 3.3～4.7 μm, 2.1～3.3 μm, 1.1～2.1 μm, 0.65～1.1 μm) cascade impactors of 400 orifices were used to collect viable bacteria and fungi, respectively. The levels of carbon monoxide (CO), carbon dioxide (CO₂), formaldehyde (HCHO), temperature, and relative humidity in the commuting trains were also recorded during the sampling period. Results show that bacterial concentrations ranged from 25 to 1530 CFU m^?3, and averaged 417 CFU m^?3. The fungal concentrations ranged from 45 to 1906 CFU m^?3, and averaged 413 CFU m^?3. Additionally, the highest fractions occurred in the fifth stage (1.1～2.1 μm) for both bacteria and fungi. The respirable fractions, R_b and R_f, for bacteria and fungi were 62.8% and 81.4%, respectively, which are higher than those in other studies. Furthermore, the bacterial concentration reached its highest level in autumn, and its lowest level in winter. However, the fungal concentration was highest in spring and lowest in winter. Though the total bacterial or fungal concentration did not exceed the recommendation standard in Taiwan, the relatively high respirable fraction in commuting trains probably implies a higher adverse health risk for sensitive commuters. This study further conducted multiple regression analysis to determine the relationship of various stage fractions of airborne bacteria and fungi with indoor air pollutants (CO and HCHO) and environmental parameters (CO₂, temperature, and relative humidity). The correlation coefficients of multiple regression analysis for total bacteria and fungi concentrations with indoor air pollutants and environmental parameters were 0.707 (p < 0.00376) and 0.612 (p < 0.00471), respectively. There are currently no formally regulated laws for indoor air quality (IAQ) in Taiwan, and this preliminary study can provide references to the Taiwan government on IAQ management.     

太仓大气细颗粒物的粒径分布及来源分析

超大城市大气环境日益改善的同时,其周边卫星城市的大气环境将逐步得到关注.利用静电低压撞击器(ELPI)在线测量上海周边卫星城市太仓大气细颗粒物(PM2.5)粒子数浓度和质量浓度的粒径分布;结合太仓大气PM2.5样品中Ca、Ti、V、Cr、Mn、Fe、Co、Ni、Cu、Zn、As、Se、Sr、CA和Pb等15种元素的浓度...     

Size distributions of trace metals in atmospheric aerosols in the United Kingdom

The size distributions of Ba, Cd, Co, Cu, Hg, Mn, Ni, Pb, Sn, Se, Sr, Zn and Fe in atmospheric aerosols were measured using impactors at three background sites in central England and southern Scotland. Coarse aerosols (>10.0 μm) were found to be undercollected by a micro-orifice uniform deposit impactor (MOUDI) when compared to an isokinetic technique, to a degree dependent on the size distribution of individual metals. The size distributions obtained in Scotland, which were typically trimodal, differed from those in central England, where modes were more variable.Characteristic size distributions allowed identification of three main behavioural types: (i) metals whose mass resided mainly within the accumulation mode (Cd, Sn, Pb, Se), (ii) those which were distributed between fine, intermediate and coarse modes (Ni, Zn, Cu, Co, Mn, Hg), and (iii) those which were mainly found within coarse particles (Fe, Sr, Ba). The measured distributions are believed to result from a combination of processes including local anthropogenic and natural sources, long-range transport and resuspension.     

Hydrogeochemical behavior of arsenic-enriched groundwater in the deltaic environment: comparison between two study sites in West Bengal, India

Groundwaters have been collected from deltaic areas of West Bengal (Chakdaha and Baruipur blocks) to record their hydrogeochemical characteristics, and to verify the mechanism of arsenic (As) release. The data reveals that shallow (<70 m) groundwaters in both areas are of Ca-Mg-HCO(3) type; however deeper (>70 m) groundwaters in Baruipur areas are slightly enriched with Na, Cl and SO(4), indicating possible saline water intrusion. The groundwater is anoxic (mean Eh: -124 and -131 mV) with high levels of As (mean: 116 and 293 mug/L), Fe (mean: 4.74 and 3.83 mg/L), PO(4) (mean: 3.73 and 3.21 mg/L) and Mn (mean: 0.37 and 0.49 mg/L), respectively for Chakdaha and Baruipur areas. The observed values of As and bicarbonate (mean: 409 and 499 mg/L) in the shallow aquifer are indicative of redox processes (e.g., oxidation of organic matter) favouring the release of As. Moreover, the presence of DOC in the shallow aquifer suggests that organic matter is young and reactive, and may actively engage in redox driven processes. Our study further confirms that both Fe- and Mn-reduction processes are the dominant mechanisms for As release in these groundwaters.     

上海市郊节假日大气颗粒物中碳和离子的粒径分布

由于人类节日活动,节日大气污染与平时相比有独特性,了解其污染特征对指导人类生活有重要意义。用Staplex公司分粒径的大流量采样器采集上海嘉定区2009—2010年节日(春节、劳动节、中秋节、国庆节)及相应临近非节日(以下简称非节日)的大气颗粒物样品,分析了颗粒物中主要化学组分的节日特征。在所研究的4个节日中,春节由于受到大量烟花爆竹燃放的影响,节日效应最为严重,且其影响主要在细粒径段(3.00μm)。春节细粒径段颗粒物质量浓度、有机碳和元素碳质量浓度分别为99.2、30.2、9.5μg/m3,与非节日的比值分别为1.5、2.6、3.4;而影响最严重的离子是K+和Mg2+,其与非节日的比值分别为29.0和23.7。总体而言,春节颗粒物浓度最高和化学组分污染最严重,其次是劳动节、国庆节、中秋节。     

Size and composition distributions of particulate matter emissions: part 1--light-duty gasoline vehicles

Size-resolved particulate matter (PM) emitted from light-duty gasoline vehicles (LDGVs) was characterized using filter-based samplers, cascade impactors, and scanning mobility particle size measurements in the summer 2002. Thirty LDGVs, with different engine and emissions control technologies (model years 1965-2003; odometer readings 1264-207,104 mi), were tested on a chassis dynamometer using the federal test procedure (FTP), the unified cycle (UC), and the correction cycle (CC). LDGV PM emissions were strongly correlated with vehicle age and emissions control technology. The oldest models had average ultrafine PM0.1 (0.056- to 0.1-microm aerodynamic diameter) and fine PM1.8 (< or =1.8-microm aerodynamic diameter) emission rates of 9.6 mg/km and 213 mg/km, respectively. The newest vehicles had PM0.1 and PM1.8 emissions of 51 microg/km and 371 microg/km, respectively. Light duty trucks and sport utility vehicles had PM0.1 and PM1.8 emissions nearly double the corresponding emission rates from passenger cars. Higher PM emissions were associated with cold starts and hard accelerations. The FTP driving cycle produced the lowest emissions, followed by the UC and the CC. PM mass distributions peaked between 0.1- and 0.18-microm particle diameter for all vehicles except those emitting visible smoke, which peaked between 0.18 and 0.32 microm. The majority of the PM was composed of carbonaceous material, with only trace amounts of water-soluble ions. Elemental carbon (EC) and organic matter (OM) had similar size distributions, but the EC/OM ratio in LDGV exhaust particles was a strong function of the adopted emissions control technology and of vehicle maintenance. Exhaust from LDGV classes with lower PM emissions generally had higher EC/OM ratios. LDGVs adopting newer technologies were characterized by the highest EC/OM ratios, whereas OM dominated PM emissions from older vehicles. Driving cycles with cold starts and hard accelerations produced higher EC/OM ratios in ultrafine particles.     

Shortwave radiative forcing efficiency of urban aerosols--a case study using ground based measurements

Aerosols reduce the surface reaching solar flux by scattering the incoming solar radiation out to space. Various model studies on climate change suggest that surface cooling induced by aerosol scattering is the largest source of uncertainty in predicting the future climate. In the present study measurements of aerosol optical depth (AOD) and its direct radiative forcing efficiency has been presented over a typical tropical urban environment namely Hyderabad during December, 2003. Measurements of AOD have been carried out using MICROTOPS-II sunphotometer, black carbon aerosol mass concentration using Aethalometer, total aerosol mass concentration using channel Quartz Crystal Microbalance (QCM) Impactor Particle analyser and direct normal solar irradiance using Multifilter Rotating Shadow Band Radiometer (MFRSR). Diurnal variation of AOD showed high values during afternoon hours. The fraction of BC estimated to be approximately 9% in the total aerosol mass concentration over the study area. Results of the study suggest -62.5 Wm(-2) reduction in the ground reaching shortwave flux for every 0.1 increase in aerosol optical depth. The results have been discussed in the paper.     

Size and composition distributions of particulate matter emissions: part 2--heavy-duty diesel vehicles

Particulate matter (PM) emissions from heavy-duty diesel vehicles (HDDVs) were collected using a chassis dynamometer/dilution sampling system that employed filter-based samplers, cascade impactors, and scanning mobility particle size (SMPS) measurements. Four diesel vehicles with different engine and emission control technologies were tested using the California Air Resources Board Heavy Heavy-Duty Diesel Truck (HHDDT) 5 mode driving cycle. Vehicles were tested using a simulated inertial weight of either 56,000 or 66,000 lb. Exhaust particles were then analyzed for total carbon, elemental carbon (EC), organic matter (OM), and water-soluble ions. HDDV fine (< or =1.8 microm aerodynamic diameter; PM1.8) and ultrafine (0.056-0.1 microm aerodynamic diameter; PM0.1) PM emission rates ranged from 181-581 mg/km and 25-72 mg/km, respectively, with the highest emission rates in both size fractions associated with the oldest vehicle tested. Older diesel vehicles produced fine and ultrafine exhaust particles with higher EC/OM ratios than newer vehicles. Transient modes produced very high EC/OM ratios whereas idle and creep modes produced very low EC/OM ratios. Calcium was the most abundant water-soluble ion with smaller amounts of magnesium, sodium, ammonium ion, and sulfate also detected. Particle mass distributions emitted during the full 5-mode HDDV tests peaked between 100-180 nm and their shapes were not a function of vehicle age. In contrast, particle mass distributions emitted during the idle and creep driving modes from the newest diesel vehicle had a peak diameter of approximately 70 nm, whereas mass distributions emitted from older vehicles had a peak diameter larger than 100 nm for both the idle and creep modes. Increasing inertial loads reduced the OM emissions, causing the residual EC emissions to shift to smaller sizes. The same HDDV tested at 56,000 and 66,000 lb had higher PM0.1 EC emissions (+22%) and lower PM0.1 OM emissions (-38%) at the higher load condition.     

A comparison of extinction and size distribution data measured at two urban sites in the U.S. and Europe

Extinction coefficients and mass size distributions were measured at St. Louis, MO. and at Vienna, Austria with the same instrumentation (an 11-wavelength automated telephotometer and an 8-stage low pressure cascade impactor, both designed at the University of Vienna). A comparison between the sites gave lower extinction coefficients, mean aerodynamic diameters, standard deviations and mass concentrations of the accumulation mode at the St. Louis site and a similar dependence of extinction on relative humidity.     

Microbially assisted phytoremediation approaches for two multi-element contaminated sites

Phytoremediation is an environmental friendly, cost-effective technology for a soft restoration of abandoned mine sites. The grasses Agrostis capillaris, Deschampsia flexuosa and Festuca rubra, and the annual herb Helianthus annuus were combined with microbial consortia in pot experiments on multi-metal polluted substrates collected at a former uranium mine near Ronneburg, Germany, and a historic copper mine in Kopparberg, Sweden, to test for phytoextraction versus phytostabilization abilities. Metal uptake into plant biomass was evaluated to identify optimal plant–microbe combinations for each substrate. Metal bioavailability was found to be plant species and element specific, and influenced by the applied bacterial consortia of 10 strains, each isolated from the same soil to which it was applied. H. annuus showed high extraction capacity for several metals on the German soil independent of inoculation. Our study could also show a significant enhancement of extraction for F. rubra and A. capillaris when combined with the bacterial consortium, although usually grasses are considered metal excluder species. On the Swedish mixed substrate, due to its toxicity, with 30 % bark compost, A. capillaris inoculated with the respective consortium was able to extract multi-metal contaminants.     

Size distribution of polycyclic aromatic hydrocarbons in urban and suburban sites of Beijing, China

PAHs in five-stage size segregated aerosol particles were investigated in 2003 at urban and suburban sites of Beijing. The total concentration of 17 PAHs ranged between 0.84 and 152 ng m(-3), with an average of 116 ng m(-3), in urban area were 1.1-6.6 times higher than those measured in suburban area. It suggested a serious pollution level of PAHs in Beijing. PAHs concentrations increased with decreasing the ambient temperature. Approximately 68.4-84.7% of PAHs were adsorbed on particles having aerodynamic diameter 2.0 microm. Nearly bimodal distribution was found for PAHs with two and three rings, more than four rings PAHs, however, followed unimodal distribution. The overall mass median diameter (MMD) for PAHs decreased with increasing molecular weight. Diagnostic ratios and normalized distribution of PAHs indicated that the PAHs in aerosol particles were mainly derived from fossil fuel combustion. Coal combustion for domestic heating was probably major contributor to the higher PAHs loading in winter, whereas PAHs in other seasons displayed characteristic of mixed source of gasoline and diesel vehicle exhaust. Biomass burning and road dust are minor contributors to the PAHs composition of these aerosol particles. Except for source emission, other factors, such as meteorological condition, photochemical decay, and transportation from source to the receptor site, should to be involved in the generation of the observed patterns.     

Source apportionment of PM2.5 at two Seattle chemical speciation sites

ABSTRACT

Positive Matrix Factorization analysis of PM_2.5 chemical speciation data collected from 2015–2017 at Washington State Department of Ecology’s urban NCore (Beacon Hill) and near-road (10th and Weller) sites found similar PM_2.5 sources at both sites. Identified factors were associated with gasoline exhaust, diesel exhaust, aged and fresh sea salt, crustal, nitrate-rich, sulfur-rich, unidentified urban, zinc-rich, residual fuel oil, and wood smoke. Factors associated with vehicle emissions were the highest contributing sources at both sites. Gasoline exhaust emissions comprised 26% and 21% of identified sources at Beacon Hill and 10th and Weller, respectively. Diesel exhaust emissions comprised 29% of identified sources at 10th and Weller but only 3% of identified sources at Beacon Hill. Correlation of the diesel exhaust factor with measured concentrations of black carbon and nitrogen oxides at 10th and Weller suggests a method to predict PM_2.5 from diesel exhaust without a full chemical speciation analysis. While most PM_2.5 sources exhibit minimal change over time, primary PM_2.5 from gasoline emissions is increasing on average 0.18 µg m^?3 per year in Seattle.     

Evaluating the size distribution characteristics and sources of atmospheric trace elements at two mountain sites: comparison of the clean and polluted regions in China

Size-resolved trace metal concentrations at two background sites were assessed during a 1-year observation campaign, with the measurements performed in parallel at two mountain sites, where Mt. Dinghu (DHS) located in the rural region of Pearl River Delta (PRD) and Mt. Gongga (GGS) located in the Tibetan Plateau region. In total, 15 selected trace elements (Mg, Al, K, V, Mn, Fe, Cu, Zn, As, Mo, Ag, Cd, Ba, Tl, and Pb) in aerosol samples were determined using inductively coupled plasma mass spectrometry (ICPMS). The major metals in these two mountain sites were Fe, K, Mg, and Ca with concentrations ranging between 241 and 1452 ng/m³, 428 and 1351 ng/m³, 334 and 875 ng/m³, and 376 and 870 ng/m³, respectively, while the trace metals with the lowest concentrations were Mo, Ag, Cd, and Tl with concentrations lower than 4 ng/m³ in DHS and 2 ng/m³ in GGS. The pronounced seasonal variability in the trace elements was observed in DHS, with lower concentrations in spring and summer and relatively high in winter and autumn, whereas seasonal variance of trace elements is hardly observed in Mt. Gongga. The size distribution pattern of crustal elements of Al, Mg, K, Ba, and Fe was quite similar in DHS and GGS, which were mainly found in coarse particles peaked at 4.7–5.8 μm. In addition, V, Mo, Ag, and Tl were also concentrated in coarse particles, although the high enrichment factor (EF?>?100) of which suggested anthropogenic origin, whereas trace metals of Cd, Mn, Zn, As, Cu, and Pb concentrated in fine mode particles. Specifically, these trace metals peak at approximately 1.5 μm in DHS, while those in GGS peaked at diameter smaller than 0.3 μm, indicating the responsible for long-range transport from the far urban and industrialized areas. Multivariate receptor model combined with the enrichment factor results demonstrated that the trace elemental components at these two background sites were largely contributed from the fossil fuel combustion (55.4% in DHS and 44.0% in GGS) and industrial emissions factors (20.1% vs. 26.5%), which are associated with long distance transport from the coastal area of Southeast China and the Northwestern India, respectively, as suggested by the backward air mass trajectory analysis. Local sources from soil dust contributed a minor variance for trace elements in DHS (9.7%) and GGS (13.8%), respectively.

     

Mapping species distributions: A comparison of skilled naturalist and lay citizen science recording

To assess the ability of traditional biological recording schemes and lay citizen science approaches to gather data on species distributions and changes therein, we examined bumblebee records from the UK’s national repository (National Biodiversity Network) and from BeeWatch. The two recording approaches revealed similar relative abundances of bumblebee species but different geographical distributions. For the widespread common carder (Bombus pascuorum), traditional recording scheme data were patchy, both spatially and temporally, reflecting active record centre rather than species distribution. Lay citizen science records displayed more extensive geographic coverage, reflecting human population density, thus offering better opportunities to account for recording effort. For the rapidly spreading tree bumblebee (Bombus hypnorum), both recording approaches revealed similar distributions due to a dedicated mapping project which overcame the patchy nature of naturalist records. We recommend, where possible, complementing skilled naturalist recording with lay citizen science programmes to obtain a nation-wide capability, and stress the need for timely uploading of data to the national repository.     

Ethylene Dosages in Denver and Marketability of Cut-Flower Carnations

Ethylene dosages required to reduce keeping life of the cut-flower, Dianthus caryophyllus L. cv “White Sim,” were compared with dosages estimated from air samples obtained in selected locations of the Denver Metropolitan region. Ethylene concentrations sufficiently high and prolonged to reduce significantly flower longevity prior to final sale are seldom attained. If flowers are harvested in an immature stage and immediately refrigerated, there should not be any economic loss. But, damage is likely after the flower is purchased and displayed at room temperature. Regardless of quality maintained in the marketing processes by the greenhouse industry, severe consumer dissatisfaction may result when ethylene sensitive plant material is purchased. The results emphasize means of avoiding pollution damage from ethylene.     

Size distributions of nano/micron dicarboxylic acids and inorganic ions in suburban PM episode and non-episodic aerosol

The distribution of nano/micron dicarboxylic acids and inorganic ions in size-segregated suburban aerosol of southern Taiwan was studied for a PM episode and a non-episodic pollution period, revealing for the first time the distribution of these nanoscale particles in suburban aerosols. Inorganic species, especially nitrate, were present in higher concentrations during the PM episode. A combination of gas-to-nuclei conversion of nitrate particles and accumulation of secondary photochemical products originating from traffic-related emissions was likely a crucial cause of the PM episode. Sulfate, ammonium, and oxalic acid were the dominant anion, cation, and dicarboxylic acid, respectively, accounting for a minimum of 49% of the total anion, cation or dicarboxylic acid mass. Peak concentrations of these species occurred at 0.54 μm in the droplet mode during both non-episodic and PM episode periods, indicating an association with cloud-processed particles. On average, sulfate concentration was 16–17 times that of oxalic acid. Oxalic acid was nevertheless the most abundant dicarboxylic acid during both periods, followed by succinic, malonic, maleic, malic and tartaric acid. The mass median aerodynamic diameter (MMAD) of oxalic acid was 0.77 μm with a bi-modal presence at 0.54 μm and 18 nm during non-episodic pollution and an MMAD of 0.67 μm with mono-modal presence at 0.54 μm in PM episode aerosol. The concomitant formation of malonic acid and oxalic acid was attributed to in-cloud processes. During the PM episode in the 5–100 nm nanoscale range, an oxalic acid/sulfate mass ratio of 40.2–82.3% suggested a stronger formation potential for oxalic acid than for sulfate in the nuclei mode. For total cations (TC), total inorganic anions (TIA) and total dicarboxylic acids (TDA), major contributing particles were in the droplet mode, with least in the nuclei mode. The ratio of TDA to TIA in the nuclei mode increased greatly from 8.40% during the non-episodic pollution period to 28.08% during the PM episode, favoring dicarboxylic acid formation in the nuclei mode. The evidence suggests stronger formation strength and contribution potential exists for dicarboxylic acids than for inorganic salts in nanoscale particles, especially in PM episode aerosol.     

Comparisons of coarse-mode aerosol nitrate and ammonium at two polluted coastal sites

Direct atmospheric fixed-nitrogen deposition can contribute to eutrophication in coastal and estuarine waters and can be enhanced by heterogeneous reactions between gaseous atmospheric nitrogen species and aerosol sea salt, which increase deposition rates. Size-segregated aerosol samples were collected from two coastal sites: Weybourne, England and Mace Head, Ireland. Major-ion aerosol concentrations were determined and temporal patterns were interpreted with the use of air-mass back trajectories. Low levels of terrestrially derived material were seen during periods of clean, onshore flow, with respective concentration ranges for nitrate and ammonium of 0.47–220 and below detection limit to 340 nmol m⁻³. Corresponding levels of marine derived material during these periods were high, with sodium concentrations ranging from 39 to 1400 nmol m⁻³. Highest levels of terrestrially derived material were seen during polluted, offshore flow, where the air had passed recently over strong source regions of the UK and northern Europe, with concentration ranges of nitrate and ammonium of 5.6–790 and 9.7–1000 nmol m⁻³, respectively. During polluted flow ∼40–60% of the nitrate was found in the coarse mode (>1 μm diameter) and under clean marine conditions almost 100% conversion was seen. In addition, our data suggests strong evidence for dissolution/coagulation processes that also shift nitrate to the coarse mode. Furthermore, such processes are thought also to give rise to the size-shifting of aerosol ammonium, since significant coarse-mode fractions of this species (∼19–45%) were seen at both sites. A comparison of the relative importance of nitrate and ammonium in the overall dry deposition of inorganic fixed-nitrogen at each site indicates that at Weybourne the mass-weighted dry deposition velocity of the latter is around double that seen at Mace Head with its resultant contribution to the overall inorganic nitrogen dry flux exceeding that of nitrate.