Investigating the effects of liquid atomization and delivery parameters of minimum quantity lubrication on the grinding process of Al2O3 engineering ceramics

Minimum quantity lubrication (MQL) is a cost-effective and environmentally friendly alternative to flood cooling. MQL spray jet has been shown to have potential to be applied successfully in different machining processes. Since the amount of lubricating liquid employed in MQL jet is very low, it is necessary to generate and apply the MQL spray efficiently. However, efficient application of MQL is not only related to spray atomization characteristics and delivery parameters but is also affected by machining conditions. The present paper demonstrates a theoretical and experimental investigation on the spray atomization and delivery parameters in the grinding process of Al₂O₃ engineering ceramics. The spray atomization characteristics studied are carrier gas velocity, liquid droplet size and liquid droplet velocity. Experiments were performed to verify the delivery parameters of MQL spray including nozzle angle, nozzle distance, lubricant flow rate and gas flow rate in the case of Al₂O₃ ceramics grinding. The experimental results confirm the theoretical outcomes and indicate that by applying optimal spray delivery parameters efficient lubrication takes place. Moreover, efficient lubrication of Al₂O₃ ceramics grinding can decrease the challenges existing in ceramics grinding processes by reducing grinding forces and surface roughness.     

纳米氧化物粒子对PVDF中空纤维膜结构与性能的影响

采用相转化法制备纳米氧化物/聚偏氟乙烯复合中空纤维膜,讨论了纳米氧化钛和氧化铝粒子对PVDF膜结构和性能的影响.应用牛血清白蛋白截留实验、扫描电子显微镜、傅立叶红外光谱分别对不同膜的分离性能、微观结构和晶相组成进行了分析.结果表明,复合膜的性能与纯PVDF膜相比有显著地改善,其中纯PVDF膜、Al₂O₃/PVDF和TiO₂/PVDF复合膜对牛血清白蛋白的截留率分别为3.27%、67.20%和86.67%,复合膜的水通量则较纯PVDF膜分别提高2.3倍和2.6倍.氮气吸附实验测定的孔径分布进一步表明复合膜的孔径分布变窄,孔径变小.     

Fabrication of Bi2O3/TiO2 nanocomposites and their applications to the degradation of pollutants in air and water under visible-light

A nanoheterojunction composite photocatalyst Bi2O3/TiO2working under visible-light(λ 420 nm) was prepared by combining two semiconductors Bi2O3 and TiO2 varying the Bi2O3/TiO2molar ratio. Maleic acid was employed as an organic binder to unite Bi2O3 and TiO2 nanoparticles. The SEM, TEM, XRD and diffuse reflectance spectra were utilized to characterize the prepared Bi2O3/TiO2nanoheterojunction. The nanocomposite exhibited unusual high photocatalytic activity in decomposing 2-propanol in gas phase and phenol in aqueous phase and, evolution of CO2 under visible light irradiation while the end members exhibited low photocatalytic activity. The composite was optimized to 5 mol% Bi2O3/TiO2. The remarkable high photocatalytic efficiency originates from the unique relative energy band position of Bi2O3 and TiO2 as well as the absorption of visible light by Bi2O3.     

Preparation and characterization of Pd/Fe bimetallic nanoparticles immobilized on Al2O3/PVDF membrane: Parameter optimization and dechlorination of dichloroacetic acid

Using a liquid–solid phase inversion method, a hybrid matrix poly(vinylidene fluoride)(PVDF) membrane was prepared with alumina(Al2O3) nanoparticle addition. Pd/Fe nanoparticles(NPs) were successfully immobilized on the Al2O3/PVDF membrane, which was characterized by Scanning Electron Microscopy(SEM) and Transmission Electron Microscopy(TEM). The micrographs showed that the Pd/Fe NPs were dispersed homogeneously. Several important experimental parameters were optimized, including the mechanical properties, contact angle and surface area of Al2O3/PVDF composite membranes with different Al2O3 contents. At the same time, the ferrous ion concentration and the effect of hydrophilization were studied. The results showed that the modified Al2O3/PVDF membrane functioned well as a support. The Al2O3/PVDF membrane with immobilized Pd/Fe NPs exhibited high efficiency in terms of dichloroacetic acid(DCAA) dechlorination. Additionally, a reaction pathway for DCAA dechlorination by Pd/Fe NPs immobilized on the Al2O3/PVDF membrane system was proposed.     

TiO2-石墨烯（Gn）复合材料光催化降解O3研究

通过改性Hummer法及溶胶凝胶法,制备出TiO2-石墨烯光催化复合材料.经吸附-光催化活性实验选出光催化活性最高的含C量为1.5%(质量分数)的TiO2-石墨烯复合材料,并在自行设计的模拟大型客机环境的气相光催化反应器中,进行O3光催化降解实验研究.结果表明,TiO2-石墨烯复合光催化材料在较短时间内对O3有较高的降解效率,且其光催化活性显著优于纯TiO2材料.初始O3浓度为(0.150～0.200)×10-6时,复合光催化剂受紫外光激发60 min的光催化降解率为66.12%,初始O3浓度为(0.950～1.000)×10-6时,其光催化降解率约为77%,较低浓度时((0.100～0.150)×10-6),O3去除率也能达到45.45%.此外,通过探讨光催化材料的重复使用性能,表明复合光催化剂重复使用4次以内,其对O3的光催化降解率保持基本稳定.     

以堇青石蜂窝陶瓷为载体的新型钒氧化物脱氮催化剂研究

以TiO₂/Al₂O₃/堇青石蜂窝陶瓷为载体,以V₂O₅-MoO₃-WO₃为活性组分,用于氨法选择性催化还原烟气中NO的新型催化剂,并对该催化剂的活性性能和微观结构进行了评价和表征.同时,将该催化剂的活性性能与其它几种活性组分相同但载体、制备方法、结构不同的催化剂进行了对比.对比结果表明,该新型催化剂能取得最好的选择性催化还原氮氧化物催化性能BET、FT IR、XPS表征实验结果表明,其高催化活性得益于大比表面积及大孔体积,而TiO₂/Al₂O₃/堇青石蜂窝陶瓷载体及其制备方法对获得好的催化剂构型起了至关重要的作用.     

Pd/CeZr/TiO2/Al2O3蜂窝状金属丝网催化剂选择催化还原NOX

采用溶胶-凝胶法和浸渍法制备了Pd/CeZr/TiO2Al2O3蜂窝状金属丝网催化剂,并将其应用于在富氧条件下以丙烯选择催化还原NOx的研究.利用扫描电镜(SEM)分析了钛酸四丁酯的含量以及涂敷次数对TiO2涂层的影响,系统地考察了Pd含量、氧气浓度和空速对蜂窝状金属丝网催化剂催化性能的影响.实验结果表明,采用钛酸四丁酯的含量为20.0%的溶胶,涂敷2次,可以在金属丝网载体上氧化铝涂层表面获得均匀、无皲裂的TiO2涂层;Pd含量在0.23%～1.06%的范围内, NOx的转化率随Pd含量的增加而减小, Pd含量为0.23%时, NOx表现最高的NOx转化率;反应气体中氧气浓度从1.5%增加到6.0%, NOx的转化率随氧气浓度的增加而增大,当氧气浓度高于6.0%, NOx的转化率则随氧气浓度的增加而迅速减小; NOx的转化率随着空速的增加而降低,在高温条件下空速对转化率的影响要大于在低温条件下.     

Catalytic performance of Fe3O4-CoO/Al2O3 catalyst in ozonation of 2-(2,4-dichlorophenoxy)propionic acid, nitrobenzene and oxalic acid in water

Fe3O4-CoO/Al2O3 catalyst was prepared by incipient wetness impregnation using Fe(NO3) 3·9H2O and Co(NO3) 2·6H2O as the precursors,and its catalytic performance was investigated in ozonation of 2-(2,4-dichlorophenoxy) propionic acid(2,4-DP) ,nitrobenzene and oxalic acid.The experimental results indicated that Fe3O4-CoO/Al2O3 catalyst enabled an interesting improvement of ozonation eciency during the degradation of each organic pollutant,and the Fe3O4-CoO/Al2O3 catalytic ozonation system followed a radical-type mechanism.The kinetics of ozonation alone and Fe3O4-CoO/Al2O3 catalytic ozonation of three organic pollutants in aqueous solution were discussed under the mere consideration of direct ozone reaction and OH radical reaction to well investigate its performance.In the catalytic ozonation of 2,4-DP,the apparent reaction rate constants(k) were determined to be 1.456×10-2 min-1 for ozonation alone and 4.740×10-2 min-1 for O3/Fe3O4-CoO/Al2O3.And O3/Fe3O4-CoO/Al2O3 had a larger Rct(6.614×10-9) calculated by the relative method than O3 did(1.800×10-9) ,showing O3/Fe3O4-CoO/Al2O3 generated more hydroxyl radical.Similar results were also obtained in the catalytic ozonation of nitrobenzene and oxalic acid.The above results demonstrated that the catalytic performance of Fe3O4-CoO/Al2O3 in ozonation of studied organic substance was universal to a certain degree.     

UV/TiO2/H2O2体系对制药废水二级出水的处理特性研究

以某制药企业的二级出水为研究对象,对比了UV/TiO₂、UV/H₂O₂、UV/TiO₂/H₂O₂ 3种高级氧化工艺的处理效果,利用自主设计的一体化光催化装置进行了连续动态试验,并通过凝胶渗透色谱（GPC）、傅里叶变换红外光谱（FT-IR）、三维荧光光谱（EEM）、斑马鱼急性毒性试验等方法研究了处理前后有机物特性和生物毒性的变化.结果表明,与UV/TiO₂和UV/H₂O₂体系相比,UV/TiO₂/H₂O₂光芬顿体系对有机物的去除效果更好,当TiO₂投加量为1 g·L^-1,H₂O₂投加量为100 mg·L^-1时,处理效果达到最佳.一体化光催化装置能够利用UV/TiO₂/H₂O₂光芬顿技术快速高效地降解二级出水中的有机污染物,反应30 min时COD去除率达到50%以上.经UV/TiO₂/H₂O₂深度处理后,废水中的大分子有机物分解转换为小分子,有机物中的不饱和结构明显减少,腐殖质等溶解性有机物基本降解完全.毒性试验结果表明,该二级出水的生物毒性经深度处理后显著降低,对斑马鱼胚胎不存在致畸致死效应.     

Sulfur(IV) oxidation by hydrogen peroxide in aqueous suspensions of SiO2, Al2O3, TiO2 and zeolite

Normal and stopped-flow spectrophotometry were used to study the rate of oxidation of sulfur(IV) (SO₃²⁻/HSO₃⁻) by H₂O₂ in aqueous suspensions of finely divided SiO₂, Al₂O₃, TiO₂ and Na-A-zeolite buffered at pH 8.2 and 4.0. Within the limits of error, the rate constants obtained agree with those measured in the absence of suspended material, i.e. under the given conditions there is no surface catalytic effect to be observed.     

Effect of oxide nanoparticles on the morphology and fluidity of phospholipid membranes and the role of hydrogen bonds

Engineered oxide nanoparticles (NPs) are widely applied in insulators, catalyzers, paints, cosmetic products, textiles and semiconductors. Their attachment on cell membrane may lead to cytotoxicity. The effects of Al₂O₃, Fe₂O₃, SiO₂, TiO₂ and ZnO NPs on membrane integrity and fluidity were studied using giant or small unilamellar vesicles in this study. Al₂O₃ and SiO₂ NPs disrupted the oppositely charged membrane, indicating the important role of electrostatic attraction. However, Fe₂O₃, TiO₂ and ZnO NPs did not cause serious membrane disruption as Al₂O₃ and SiO₂ NPs. Membrane fluidity was evaluated by the generalized polarity (GP) values of Laurdan fluorescent emission. SiO₂ NPs induce the membrane gelation of both positively and negatively charged membrane. Al₂O₃ and ZnO NPs induced the gelation of the oppositely charged membrane, but did not cause obvious membrane gelation to the like charged membrane. The phospholipid molecular structural changes after NP exposure were analyzed by Fourier transform infrared (FT-IR) spectroscopy. FT-IR spectra revealed the hydrogen bond formation between NPs and the carbonyl/phosphate groups of phospholipids. Al₂O₃ and SiO₂ NPs showed strongest evidence of hydrogen bonding on their FT-IR spectra. It was consistent with the microscopic observation and fluorescent data that Al₂O₃ and SiO₂ NPs caused more serious membrane disruption and gelation. This study on membrane damage provides further knowledge on the cytotoxicity of nanomaterials and the safety of NP application.     

PbO2/TiO2-NT/Ti电极的制备及电催化性能研究

采用阳极氧化法制备了TiO_2纳米管(TiO_2-NT),研究了阳极氧化时间对TiO_2-NT形貌与结构的影响.结果表明,氧化时间为180 min时,TiO_2-NT排列紧密,管口形状接近圆形,管径为93 nm左右.以TiO_2-NT为底层采用电沉积法制备PbO_2/TiO_2-NT/Ti电极,PbO_2/TiO_2-NT/Ti电极与传统PbO_2/SnO_2-Sb2O3/Ti电极形貌、结构、电化学性能、使用寿命对比分析结果表明,与PbO_2/SnO_2-Sb2O3/Ti电极相比,PbO_2/TiO_2-NT/Ti电极具有较小的晶粒尺寸、较高的催化氧化活性和较长的使用寿命.     

TiO2-Fe3+可见光催化H2O2降解阿特拉津的协同效应

以内分泌干扰物阿特拉津为模型污染物,研究了TiO2-Fe3+可见光催化H2O2降解阿特拉津的协同效应.结果表明,在H2O2存在条件下,金红石TiO2经可见光激发可持续稳定地产生.OH自由基,在Fe3+协同作用下,.OH自由基生成量急剧增加;TiO2能可见光催化H2O2降解阿特拉津,金红石TiO2显示出较锐钛矿TiO2及混晶TiO2(TiO2P25)更高的催化活性,反应60 min,阿特拉津的降解率可达40%;以Fe3+协同TiO2可见光催化H2O2降解阿特拉津时,反应效率显著加快,反应5 min即对阿特拉津的降解率达到100%,而金红石TiO2显示出更为明显的协同效应.     

有机膜的无机改性及其性能研究

以无机纳米氧化铝粒子作为无机添加剂与聚偏氟乙烯（PVDF）共混,采用相转换法合成了有机-无机共混超滤膜.通过测定膜与纯水的接触角,表征膜的亲水性;用激光共聚焦显微镜(CLSM)、扫描电镜（SEM）和透射电镜（TEM）观察了膜的表面结构、表面孔分布和断面孔的结构及纳米颗粒在膜中的分散情况;利用杯式超滤装置对改性膜的透过性能、截留性能以及抗污染性能进行了测试;用强度测定仪测定了膜强度.结果表明,纳米Al₂O₃ 的加入改善了PVDF膜的表面亲水性、通量、强度和抗污染性.     

Preparation of MgO/B2O3 coatings by plasma spraying on SUS304 surface and effects of heat-resistant

This study mainly deals with the preparation of MgO/B₂O₃ coatings by plasma spraying on the SUS304 surface and the effects of heatresistant. The power materials of low thermal conductivity were selected to control the heat divergent performance of high temperature parts. The reticular micro-structure between the cover thermal layer and the substrate was prepared by using the plasma spraying method. The powder mixture of MgO and B₂O₃ were selected as spraying materials and the SUS304 was used as the substrate material. The MgO/B₂O₃ coating was prepared on the surface of the SUS304 to provide better cover thermal performance. The properties of the microstructures and the morphologies were studied by Optical Microscope, Scanning Electron Microscope, Electron Probe Microanalyzer, and X-ray Diffraction. The results showed that the cover thermal performance has been improved.     

Effect of Ce doping of TiO2 support on NH3-SCR activity over V2O5-WO3/CeO2-TiO2 catalyst

CeO2–TiO2composite supports with different Ce/Ti molar ratios were prepared by a homogeneous precipitation method, and V2O5–WO3/CeO2–TiO2catalysts for the selective catalytic reduction（SCR） of NOx with NH3 were prepared by an incipient-wetness impregnation method. These catalysts were characterized by means of BET, XRD, UV–Vis,Raman and XPS techniques. The results showed that the catalytic activity of V2O5–WO3/TiO2 was greatly enhanced by Ce doping（molar ratio of Ce/Ti = 1/10） in the TiO2 support.The catalysts that were predominantly anatase TiO2 showed better catalytic performance than the catalysts that were predominantly fluorite CeO2. The Ce additive could enhance the surface adsorbed oxygen and accelerate the SCR reaction. The effects of O2 concentration, ratio of NH3/NO, space velocity and SO2 on the catalytic activity were also investigated. The presence of oxygen played an important role in NO reduction. The optimal ratio of NH3/NO was 1/1 and the catalyst had good resistance to SO2 poisoning.     

Fe2O3/TiO2负载膨胀珍珠岩光催化降解罗丹明B

为获得高效催化活性的光催化材料,研究不同煅烧氛围对材料在可见光下催化性能的影响,以膨胀珍珠岩（EP）为载体,采用溶胶-凝胶法,在不同煅烧氛围（O₂和/或NH₃）下制备Fe₂O₃/TiO₂负载EP的光催化复合材料〔Fe₂O₃-TEP（O₂）、Fe₂O₃-TEP（NH₃）、Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）〕,采用EDS（X-射线色散能谱）、BET（比表面积及孔径分析）、XRD（X射线衍射）、SEM（扫描电子显微镜）、XPS（X射线光电子能谱）等对复合材料进行表征,并研究了其在可见光下对罗丹明B的光催化降解效果.结果表明:①复合材料成功负载了Ti、Fe元素,负载的TiO₂以锐钛矿型存在,Fe₂O₃的掺杂增强了TiO₂对可见光的响应能力;②不同的煅烧氛围明显影响复合材料的晶粒尺寸、比表面积和光催化性能,其中,Fe₂O₃-TEP（O₂,NH₃）的光催化性能最好,4 h后罗丹明B降解率达到87.59%,Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）4 h后对罗丹明B的降解率则分别为65.02%、62.48%和47.48%;③在试验条件下,复合材料的光催化反应符合一阶反应动力学方程,Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）相应的降解速率常数分别为0.008 3、0.004 3、0.004 3和0.002 7 min-1.研究显示,通过溶胶-凝胶法所制备的复合材料（Fe₂O₃-TEP）经煅烧后所得矿相均一;Fe₂O₃掺杂TiO₂可形成Ti—O—Fe键,减小TiO₂固有的禁带宽度;复合材料光催化性能也受到煅烧氛围的影响,先O₂后NH₃煅烧条件下所得材料的光催化性能最佳.      

V2O5/TiO2催化剂中毒机理的试验研究

选择性催化还原(SCR)催化剂是SCR烟气脱硝技术的核心,是整个SCR系统脱硝效率和经济性的决定因素.本文工作的主要研究思路是以钒钛SCR催化剂为研究对象,研究了H2O和SO2,以及相同含量下K、Na、Ca、Pb的氧化物对钒钛催化剂NO转化率的影响.H2O的存在会抑制V2O5/TiO2催化剂脱硝活性,而SO2在一定程度上促进(V2O5/TiO2)催化剂的SCR脱硝反应,提高NO转化率;碱金属K对钒钛催化剂的钝化作用都是最强,K2O和Na2O的掺入会抑制钒钛催化剂上V2O5的还原能力,而CaO和PbO的掺入对钒钛催化剂上V2O5的还原能力影响较小.     

TiO2-PW9复合催化剂光催化降解游离氰

采用水热法制备了二氧化钛(TiO_2)与三缺位磷钨酸钠(Na_8H[β-A-PW_9O_(34)]·24H_2O)共价结合形成的TiO_2-PW_9复合催化剂,并对其光催化降解游离氰(CN~-)的效果进行了研究.NMR和XPS等表征结果证明,Na_8H[β-A-PW_9O_(34)]·24H_2O(简写为Na-PW_9)已成功负载于TiO_2上.光电化学表征结果表明,Na-PW_9的引入可有效提高TiO_2的界面电荷转移.光催化实验结果表明,与单独TiO_2相比,TiO_2-PW_9的光催化活性有明显提高.同时,探究了初始CN~-浓度和催化剂投加量对CN~-去除的影响.结果表明,当初始CN~-浓度为0.3 mmol·L~(-1)、催化剂投加量为1 g·L~(-1)时,复合催化剂的光催化活性最佳,反应150 min后,CN~-的去除率达到81%.CN~-的氧化产物分析结果表明,氰酸根(CNO~-)是CN~-氧化的唯一产物.自由基淬灭实验和电子自旋共振(ESR)波谱分析结果表明,~1O_2是反应体系中的主要活性氧物种.本实验可为多功能催化材料的开发及其在含氰废水污染控制领域的应用提供参考.