D401与N-117负载 Fe（Ⅱ）非均相Fenton法催化降解苯酚

分别采用D401和N-117负载Fe（Ⅱ）制备非均相Fenton催化剂,探讨两种催化剂在不同初始溶液pH、初始H₂O₂质量浓度和保存条件下,催化降解苯酚的效果和铁溶出情况。结果表明：两种催化剂均能拓展Fenton反应pH范围;D401负载Fe（Ⅱ）催化苯酚降解速率较快,苯酚降解率随初始溶液pH升高而下降,溶出铁催化的均相Fenton反应是苯酚降解的主要原因;N-117负载Fe（Ⅱ）催化剂苯酚降解速率随初始溶液pH升高而下降,非均相Fenton反应是主要反应过程;初始H₂O₂质量浓度升高能使D401负载Fe（Ⅱ）的溶出总铁质量浓度显著升高,但对N-117负载Fe（Ⅱ）影响很小;水中较高的DO能显著降低两种催化剂的苯酚降解效果。     

Thermal decomposition of cement–asbestos at 1100 °C: how much “safe” is “safe”?

Journal of Material Cycles and Waste Management - The products of cement–asbestos treated in air at 1100 °C were characterized by a multi-methodological approach to determine:...     

中国·西南再生资源产业基地奠基

2009年10月18日,投资32亿元的西南再生资源产业基地在四川内江正式破土动工,一期投资4亿元,主要包括再生资源市场交易区等,预计2010年建成投产。该基地将成为西南地区最大的废旧塑料回收和再生产的产业基地。     

Long Term Trends in Concentration of Major Pollutants (SO<Subscript>2</Subscript>, CO,NO, NO<Subscript>2</Subscript>, O<Subscript>3</Subscript> and PM<Subscript>10</Subscript>) in Prague – Czech Republic (Analysis of Data Between 1992 and 2005)

To assess the effect of changes in traffic density and fuels used for heating at the beginning of the 1990s, 1992–2005 monthly averages of PM₁₀, SO₂, NO₂, NO, CO and O₃ from Prague, the Czech capital, were analyzed together with long term trends in emissions of major pollutants, fuel consumption and number of vehicles registered in Prague. The data from all monitoring stations were retrieved from the database of the state automated monitoring system. Correlation coefficients between ambient monthly averaged temperature and all pollutants of concern showed distinct seasonal trends. The results showed that while SO₂ and to some extent also CO concentrations dropped namely in the first half of the analyzed period (1992–1997) as a result decreased fossil fuel consumption for local heating, the behaviour of other pollutant concentrations followed a different pattern. PM₁₀ concentrations decreased during the beginning of the 1990s but showed a sign of increase after 2000. Concentrations of ozone and NO₂ did not reveal any significant change throughout the whole studied period. It can be concluded that during the studied period traditional urban sources of pollution, such as coal and oil combustion, lost their importance but were simultaneously substituted by pollutants from automotive transport (namely PM and NO₂) making the problem of air quality even worse.     

Biodegradation of Poly-ε-caprolactones and Poly-<Emphasis Type="SmallCaps">l</Emphasis>-lactides by Fungi

This work assessed biodegradation, by Aspergillus, Fusarium, Penicillium and Parengyodontium fungi, of four samples of poly-ε-caprolactone (PCL), three samples of poly-l-lactide (PLA) and one sample of poly-d,l-lactide (DL-PLA) produced by ring-opening polymerization initiated by aluminium complexes of corresponding lactones. Mesophilic fungal strains actively biodegrading PCL (F. solani) and PLA (Parengyodontium album and A. calidoustus) were selected. The rate of degradation by the selected fungi was found to depend on the physicochemical and mechanical properties of the polymers (molecular weight, polydispersity, crystallinity). The most degradable poly-ε-caprolactone sample was shown to have the lowest molecular weight; the most biodegradable polylactide DL-PLA had the lowest crystallinity. Mass spectral analysis of biodegraded polymer residues showed PCL to be degraded more intensively than PLA. It is established that in the case of Parengyodontium album the colonization of the films of polypropylene composites with DL-PLA is observed, which will undoubtedly contribute to their further destruction under the influence of abiotic factors in the environment.     

二级膜分离—冷凝—吸附工艺处理石化罐区废气

采用二级膜分离—冷凝—变压吸附工艺回收处理含有高浓度挥发性有机物和苯系物的炼厂罐区外排“呼吸气”。结果表明,进气的非甲烷总烃质量浓度范围41 000~182 000 mg/m³,进气中苯、甲苯和二甲苯的质量浓度分别为400~1 400 mg/m³,150~1 600 mg/m³,300~2 100 mg/m³时,尾气中非甲烷总烃质量浓度始终低于80 mg/m³,去除率均高于99.9%,苯、甲苯和二甲苯的去除率分别为99.6%、99.6%和99.8%。抗冲击负荷实验将进气量提高50%,尾气中非甲烷总烃质量浓度仍低于80 mg/m³。二级膜单元可以高效浓缩轻烃,既回收获得可燃气,又解决了轻烃积累所造成的尾气超标难题。     

#x0201c;两酸#x0201d;装置大气污染源分析及治理

石化企业的酸性水汽提装置、酸性干气脱硫装置和硫磺回收装置统称为#x0201c;两酸#x0201d;装置。对#x0201c;两酸#x0201d;装置所采用的工艺流程进行详细分析,得出#x0201c;两酸#x0201d;装置的有组织排放大气污染物主要为SO₂和NO_x,无组织排放大气污染物主要为H₂S、NH₃、有机硫化物和烃类。无组织排放源集中在各单元反应器、储罐和酸性气管线。针对无组织排放源,从防止逸散和恶臭治理两个方面提出了相应的污染防治措施,并比较了溶剂吸收法、燃烧法、湿法化学吸收法等目前常用的恶臭治理技术的优缺点。     

加载絮凝—超滤—反渗透组合工艺处理PCB电镀废水

采用加载絮凝—超滤—反渗透组合工艺处理含大量重金属离子的印制电路板（PCB）电镀废水。考察了絮凝污泥回流比和水力条件对加载絮凝效果的影响,确定了最佳工艺参数：在加碱沉淀pH 10.5、混凝pH 9.0、PAC投加量10 mg/L、PAM投加量1.0 mg/L的条件下,污泥回流比为47%,加碱沉淀、混凝、絮凝的搅拌转速分别为250,150,50 r/min,搅拌时间分别为6,8,4 min。中试结果表明：经加载絮凝预处理后,总铜、总镍和浊度的平均去除率分别为99.4%、99.3%和93.1%;预处理出水经超滤—反渗透系统处理后,出水水质全部达标。     

2&#215;300MW机组石灰石-石膏烟气脱硫吸收塔设计

选用石灰石-石膏工艺对山西某电厂2&#215;300MW机组进行烟气脱硫,对其核心设备吸收塔的本体进行设计计算,并对其中的设备进行了选型。     

Biodegradation of Poly(ε-caprolactone) (PCL) Film by <Emphasis Type="Italic">Alcaligenes faecalis</Emphasis>

The biodegradation behavior of PCL film with high molecular weight (80,000 Da) in presence of bacterium Alcaligenes faecalis and the analysis of degraded polymer film have been carried out. Thin Films of PCL were prepared by means of solution casting method and the bacterial degradation behavior was carried in basal medium, in presence of bacteria with time variation after UV treatment. It was observed that after UV treatment the degradation of polymer film was increased and the degradation rate followed a three steps degradation mechanism. The degraded polymer film was analyzed by means of Differential Scanning Calorimeter (DSC), Thermo Gravimetric Analyzer (TGA) and Fourier Transform Infrared Spectroscope (FTIR). DSC results revealed that at the initial stages of the degradation up to 15–20 days, the bacterium preferentially degrades the amorphous parts of the polymer film over the crystalline zone. Thermo gravimetric analysis highlighted the low temperature stability of degraded films with extent of degradation. FTIR results showed the chain scission mechanism of the polymer chains and also supported the preferential degradation of amorphous phase over crystalline phase in the initial stages of the degradation.     

缺氧—好氧—催化臭氧氧化工艺处理石化厂含盐废水

采用缺氧—好氧—催化臭氧氧化工艺处理某石化厂的含盐废水。实验结果表明：在进水COD为200~350 mg/L的条件下,经生化处理后的出水COD稳定在50~60 mg/L,COD去除率稳定在75%左右;在臭氧投加量为4.5 g/L、V（催化剂Ⅱ）∶V（废水）=1.5∶1的条件下,进行连续催化臭氧氧化后出水COD稳定在20 mg/L以下,COD去除率大于70%,满足DB 61/224—2011《黄河流域（陕西段）污水综合排放标准》。表征结果显示,催化剂表面含有铜元素,比表面积为250.815 m²/g,吸水率为60.9%,经过滤可去除废水中残留的催化剂。     

Potential of <Emphasis Type="Italic">pinhão</Emphasis> Coat as Constituents of Starch Based Films Using Modification Techniques

The potential of lignocellulosic fibers obtained by dry grinding of pinhão coat as fillers in starch filmogenic solutions for packaging applications was evaluated in this work. To improve the incorporation of this waste into the starch solutions different physical and chemical treatments were conducted. Thereafter, morphology, chemical structure, crystallinity and water absorption of the pinhão coat powders were determined. The composites were also characterized regarding their morphology, chemical structure, crystallinity, mechanical properties, water vapor permeability and hydrophilicity. Poor fiber/matrix adhesion and high water absorption of the fibers were evidenced. Consequently, water vapor permeability of composites was increased by incorporating the fibers. Moreover, mechanical properties were improved and the morphological results were used to support the water absorption differences among the powders. Regarding the food packaging applications, starch/pinhão coat composites appeared as promising materials to reach the requirements of respiring food products.     

微电解—Fenton氧化—絮凝组合工艺处理油田压裂废水

采用微电解—Fenton氧化—絮凝组合工艺处理油田压裂废水,优化了工艺条件。实验结果表明：最佳工艺条件为初始废水pH 3.0、铁屑加入量1.5 g/L（铁屑与活性炭的质量比1∶1）、微电解时间80 min、Fenton氧化时间120 min、H₂O₂加入量940 mg/L,阳离子聚丙烯酰胺加入量120 mg/L;在最佳工艺条件下处理废水后,COD由3 116.0 mg/L降至681.3 mg/L,总COD去除率达78.1%,3个工段的COD去除率依次为33.1%,37.9%,7.1%,出水水质满足现场回注标准（SY/T 5329—2012《碎屑岩油藏注水水质推荐指标及分析方法》）;该组合工艺对废水的处理效果远优于单独微电解、Fenton氧化或絮凝工艺,且方法简单易行、药剂利用率高。     

煤化工企业高盐废水的“零排放”技术

采用“混凝沉淀-微滤-组合反渗透”工艺对某煤化工企业的高盐废水进行浓缩处理,浓水通过蒸发结晶进行脱水,产水采用常规反渗透进行水回收。运行结果表明,经30 d运行,水回收率保持在85%以上,脱盐率稳定在95%以上,常规反渗透产水水质稳定,产水电导率、浊度、Cl^-质量浓度和COD的平均值分别为12.5 μs/cm,0.1 NTU,7.8 mg/L,1.8 mg/L,满足《炼化企业节水减排考核指标与回用水质控制指标》（Q/SH0104-2007）中污水回用于循环冷却水的水质指标和设计产水水质要求,实现了废水的近“零排放”。     

絮凝#x02014;微波辐射#x02014;Fenton试剂氧化法深度处理焦化废水

用絮凝#x02014;微波辐射#x02014;Fenton试剂氧化法深度处理焦化废水,研究了微波辐射时间、微波功率、FeSO₄加入量、H₂O₂加入量和废水pH对废水处理效果的影响。实验结果表明：在聚合氯化铝加入量为350mg/L、聚丙烯酰胺加入量为12mg/L、废水pH=5、FeSO₄加入量为250mg/L、H₂O₂总加入量为1400mg/L、H₂O₂分3次投加、微波功率为400W、微波辐射时间为60min的条件下,处理后出水的浊度、色度和COD去除率分别为98.59%,97.62%,86.21%。处理后出水澄清透明,COD为50.34mg/L,满足GB50050#x02014;2007《工业循环冷却水处理设计规范》的要求。     

酸析—微电解—Fenton试剂氧化联合工艺预处理苯达松废水

采用酸析—微电解—Fenton试剂氧化联合工艺预处理苯达松废水。考察了酸析pH、铸铁粉加入量、微电解时间、双氧水加入量、Fenton试剂氧化时间等因素对废水处理效果的影响。实验结果表明：最佳工艺条件为酸析pH 3.0,铸铁粉加入量1.0 g/L,微电解时间2 h,Fenton试剂氧化时间4 h,双氧水加入量25 mL/L;在最佳工艺条件下处理初始COD为22 500 mg/L、BOD₅/COD为0.08、色度为2 500倍的苯达松废水,总COD去除率为96.2%,出水COD为858 mg/L,出水色度为150倍,BOD₅/COD为0.38;采用微电解—Fenton试剂氧化联合工艺预处理酸析后的苯达松废水,处理效果远高于单独微电解和单独Fenton试剂氧化工艺。     

固相萃取—微波衍生化—GC-MS法同时测定水中6种雌激素物质

建立了固相萃取—微波衍生化—气相色谱-质谱联用法快速同时测定水中雌酮（E1）、17α-雌二醇（α-E2）、17β-雌二醇（β-E2）、雌三醇（E3）、17α-乙炔基雌二醇（EE2）、双酚A（BPA）等6种雌激素物质的分析方法,对色谱柱升温程序、固相萃取及衍生化条件进行了优化。色谱柱最佳升温程序为：初始温度50 ℃,保持2 min;以20 ℃/min速率升至260 ℃,保持5 min;最后以10 ℃/min速率升至280 ℃,保持5 min。实验结果表明,在选取 HC-C18萃取小柱、添加双（三甲基硅烷基）三氟乙酰胺（BSTFA）+1%三甲基氯硅烷（TMCS）+吡啶作为衍生化试剂、微波315 W衍生化加热4 min的条件下,6种目标物标准曲线的相关系数均大于0.999,BPA、E1、EE2及E3的线性范围为3~300 ng/L,17α-E2及17β-E2的线性范围为5~300 ng/L,方法检出限为2.0~5.0 ng/L,加标回收率为76.45%~96.24%。     

离子交换树脂D001对罗丹明B的吸附特性

采用强酸性阳离子交换树脂D001作为吸附剂吸附脱除水溶液中的罗丹明B(Rh B)。SEM和FTIR表征结果显示:D001树脂表面存在孔隙,可增加树脂的比表面积;树脂表面的磺酸基团可通过与阳离子染料Rh B络合而将其吸附。实验结果表明:Langmuir等温吸附模型能更好地描述树脂对Rh B的吸附规律,升高温度有利于树脂吸附Rh B;吸附过程符合Lagergren准一级动力学方程,初始Rh B质量浓度为20 mg/L时吸附活化能为7.06 k J/mol;树脂对Rh B的吸附是一个自发的、吸热的、熵推动的过程;颗粒扩散为吸附过程的控制步骤;树脂具有良好的重复使用性能。     

催化臭氧氧化—好氧生化—膜分离组合工艺处理砷化镓生产废水的工程应用

为了解决砷化镓生产废水含有磷酸盐、氟化物、砷化物以及难沉降亚微米级悬浮物的处理难点,首先采用催化臭氧氧化—好氧生化深度预处理废水,再采用RO膜分离工艺进行处理。结果表明：催化臭氧氧化法使废水中亚微米级悬浮物脱稳,有利于悬浮物的混凝沉降,并优化了膜分离阶段的分离环境,可延长膜使用寿命,降低运行成本;经过膜分离后,出水砷质量浓度为0.01 mg/L,氟质量浓度为1.0 mg/L,COD、TP、TN和ρ（NH₃-N）为10,0.01,0.50,0.50 mg/L,均达到《地表水环境质量标准》（GB3838—2002）Ⅲ类水质标准。     

A New Polymer Platform for the Future — Sorona<Superscript>®</Superscript> from Corn Derived 1,3-Propanediol

Responding to environmental, sustainability, business, and market factors, DuPont has commercialized a new polymer platform, Sorona®, based on 1,3-propanediol. The physical and chemical property advantages over other polymers are described. The diol component of this polymer, 1,3-propanediol, has been demonstrated to be manufacturable via biological (fermentation) process from corn sugar. The economic, environmental, and process/product quality advantages of bio-PDO over conventional diols are discussed.