Road traffic mortality in the Slovak Republic in 1996–2014

Objective: Road traffic mortality takes an enormous toll in every society. Transport safety interventions play a crucial role in improving the situation. In the period 1996–2014 several road safety measures, including a complex new road traffic law in 2009, were implemented in the Slovak Republic, introducing stricter conditions for road users.

The aim of this study is to describe and analyze the trends in road user mortality in the Slovak Republic in individual age groups by sex during the study period 1996–2014.

Methods: Data on overall mortality in the Slovak Republic for the period 1996–2014 were obtained from the Statistical Office of the Slovak Republic. Mortality rates were age-adjusted to the European standard population. Joinpoint regression was used to assess the statistical significance of change in time trends of calculated standardized mortality rates.

Results: Mortality rates of all types of road users as well as all age groups and both sexes in the Slovak Republic in the period 1996–2014 are decreasing. The male : female ratio decreased from 4:1 in 1996 to 2:1 in 2014. Motor vehicle users (other than motorcyclists) and pedestrians have the highest mortality rates among road user groups. Both of these groups show a significant decline in mortality rates over the study period. Within the age groups, people age 65 years and over have the highest mortality rates, followed by the age groups 25–64 and 15–24 years old.

Joinpoint regression confirmed a steady, significant decline in all mortality rates over the study period. A statistically significant decrease in mortality rates in the last years of the study period was observed in the age group 25–64 and in male motorcycle users.

Assessing the impact of the 2009 road traffic law, a drop was observed in the average standardized mortality rate of all road traffic users from 14.56 per 100,000 person years in the period 1996–2008 to 7.69 per 100,000 person years in the period 2009–2014. A similar drop in the average standardized mortality rate was observed in all individual road user groups.

Conclusions: The implementation of the new traffic regulations may have contributed significantly to the observed decrease in mortality rates of road users in the Slovak Republic. A significant decrease in mortality was observed in all population groups and in all groups of road users. The introduction of a new comprehensive road traffic law may have expedited the decrease of road fatalities, especially in the age group 25–64 years old. This type of evidence-based epidemiology data can be used for improved targeting of future public health measures for road traffic injury prevention.     

Managing safety in hydropower projects in emerging markets – Experiences in developing from a reactive to a proactive approach

International companies investing in emerging markets need to address the management of safety under varying conditions. The paper presents an evaluation of the approaches taken by an international hydropower company in two different construction projects, one in India and one in the Philippines. In the first project, the company had to intervene as a reaction to poor safety and overall performance. Based on previous experiences, the company selected a proactive approach in the second project, involving use of the contracting process to ensure adequate conditions from the start of construction and onwards. The paper accounts for the safety performance results in the two projects and interprets them in relationship to external and internal influencing factors in the respective project. It is concluded that a proactive approach has the potential of delivering satisfactory safety results at moderate costs for follow-up. A reactive approach risks exposing the company to ethical and reputation risks due to a poor safety performance before the corrective actions have taken full effect. It is also resource demanding. Results demonstrate the feasibility of turning around a project’s safety performance also when preconditions are challenging.     

Relative Risk of Fatal Injury in “High-Performance-Small-Motorcycle” Crashes in Malaysia

This study presents an analysis of injuries (severe and fatal) sustained by “high-performance-small-motorcycle” users in Malaysia and establishes the relationship between fatality risk and human factors, exposure and vehicle factors resulting from motorcycle crashes. From the data gathered a statistical model based on logistic regression modeling technique has been developed. Five variables found to have a significant influence on fatality risk (p < 0.05) were age, location sites, engine capacity, object/vehicle struck and collision types.     

Design for occupational safety and health of workers in construction in developing countries: a study of architects in Nigeria

Purpose. Design for safety (DfS) of workers is amongst the prominent ways of tackling poor occupational safety and health performance in construction. However, in developing countries there is extremely limited research on DfS. This study thus makes an important contribution to the subject of DfS in developing countries by specifically examining the awareness and practice of DfS amongst architects within the construction sector of Nigeria. Materials and methods. A survey of architects, yielding 161 valid responses, was conducted. Results. While there is high awareness of the concept of DfS, the actual practice is low. Additionally, although there is high interest in DfS training, the engagement in DfS training is low. Significantly, awareness of DfS, training and education related to DfS, and membership of a design professional body have very limited bearing on the practice of DfS by architects. Conclusions. The findings are thus symptomatic of the prevalence of influential DfS implementation barriers within the construction sector. Industry stakeholders should seek to raise the profile of DfS practice within the sector. Furthermore, similar empirical studies in the construction sector of other developing countries would be useful in shedding light on the status of DfS in these countries.     

Managers’ conceptions regarding human factors in air traffic management and in airport operations

Human factors (HF) in creating and managing safety in complex systems is a continuous topic of research and discussion. In the aviation organisation under study here, an HF expert had started work in a newly created position one and a half years prior to the study. The aim of the study was to find out if HF was seen as a safety creating factor and what the conceptions of HF were in regard to the theoretical developments in the field. These topics were studied in order to determine the most effective means of implementing HF-work within the organisation. Two manager groups (upper and middle management) were targeted as subjects of the study due to their crucial role in developing working culture. Twenty-one managers were interviewed from nine units that represented three operational environments (radar units with heavy traffic, combined civil/military units and procedural air traffic control units, including airport operations. Managers were found to have disjointed and vague conceptions of HF and a lack of shared vision or strategy regarding HF. Some managers lacked an appropriate conception of HF. The present situation can prevent the organisation from utilizing HF competence in maintaining and developing the safety of services. Conceptions were most up-to-date at units, where outside pressures for change had forced managers to take HF issues into account in their operational environments. While the long-term implementation of HF faces considerable challenges, the article gives several proposals for organisational structures that support a more effective realization of HF.     

Risk assessment in support to land-use planning in Europe: Towards more consistent decisions?

Recognising the importance of establishing appropriate separation distances between hazardous installations and vulnerable residential areas for mitigating the effects of industrial accidents, the European legislation for the control of major accident hazards - the so-called Seveso II Directive - calls for procedures ensuring that technical advice is taken systematically into account for land-use planning (LUP) purposes. Due to historical, administrative, cultural and other reasons, these European Union’s Member States which have consolidated procedures for addressing this issue, have employed different approaches, methods and criteria, with a potential for great divergence in the resulting land-use planning decisions. In order to address this situation and to increase consistency and ‘defendability’ of land-use planning decisions in the EU, a European Working Group has been established and is operating under the coordination of the European Commission’s Joint Research Centre (JRC). This Group, consisting of experts from the EU Member States, the industry and the academia, is trying to understand the different approaches and their implications to LUP decision-making, to develop guidelines in support to these decisions and to examine data sources and tools for consistent application of risk assessment in support to LUP. This paper presents the activities of the Group, reviews the situation with respect to LUP in Europe and discusses whether a direction towards more consistent LUP decisions is being followed in Europe.     

Experimental investigation of fast flame propagation in stratified hydrogen–air mixtures in semi-confined flat layers

This paper presents results of an experimental investigation on fast flame propagation and the deflagration-to-detonation transition (DDT) and following detonation propagation in a semi-confined flat layer filled with stratified hydrogen–air mixtures. The experiments were performed in a transparent, rectangular channel open from below. The combustion channel has a width of 0.3 m and a length of 2.5 m. The effective layer thickness in the channel was varied by using different linear hydrogen concentration gradients. The method to create quasi-linear hydrogen concentration gradients that differ in the range and slope is also presented. The ignited mixtures were accelerated quickly to sonic flame speed in the first obstructed part of the channel. The interaction of the fast flame propagation with different obstacle set-ups was studied in the second part of the channel. The experimental results show an initiation of DDT by one additional metal grid in the obstructed semi-confined flat layer. Detonation propagation and failed detonation propagation were observed in obstructed and unobstructed parts of the channel.     

The injury epidemiology of adult riders in vehicle-two-wheeler crashes in China,Ningbo, 2011–2015

Introduction: We used road crashes between vehicles and two-wheelers from Yinzhou District Ningbo in 2011–2015 from the China In-depth Accident Study (CIDAS) as sample cases. The risk factors of different injury severity grades were analyzed. Method: The classification tree model was used to screen the possible interaction items, and the corresponding regression model was constructed according to the results of the tree model to explore the influencing factors of cyclist injury. Results: The road types, weather types, gender, age of the riders, and vehicle speed were significantly correlated with the dependent variables. The interaction effect of gender*road type, weather*age, weather*speed and speed*age were obtained through a tree model. Conclusions: The risk of male casualties at the crossroads was 3.31 times higher than that of female casualties at the straight roads. On sunny days, the risk of crash casualties in Ningbo was low, and the fatality risk when the speed reached 38 km/h was 10%. Under the interaction effect of weather and age, the fatality risk in cloudy/foggy and rainy days was almost coincident, and the serious risk in cloudy/foggy conditions was the highest. Practical applications: Through factor analysis, it is confirmed that there is interaction effect among the factors, and it can provide reference for relevant departments to formulate more targeted and effective governance strategies.     

Emergency response study for chemical releases in the high-tech industry in Taiwan—A semiconductor plant example

In the past two decades, there has been continuous investment and expansion of semiconductor, photoelectric panel, or solar cell plants in the high-tech industry. For example, establishing a semiconductor plant costs about US$ 3 billion. In addition, the output value of integrated circuits (IC) of Taiwan as a whole is estimated to be about US$ 5.215 billion, and globally of US$ 275.2 billion in 2008. A large amount and a variety of specialty gases or chemicals are applied during processes in high-tech facilities and these chemicals are characterized by inflammability, toxicity, and corrosiveness. Accidents may result once errors or leaks occur in any part of the supply chain, which consists of storage facilities, supply equipment, process machines, and tail gas elimination devices. Personnel casualties can result in serious situations. This study discusses the emergency response procedures and common response defects in semiconductor plants with a view to enhancing emergency response effects and capabilities, avoiding casualties, reducing property loss and shortening operation interruption.     

Deformation patterns in WorldSID 50th percentile dummy instrumented with IR-TRACC and RibEye™ in different loading configurations

Objective: The purpose of this study was to investigate the effect of different loading configurations on the WorldSID 50th percentile male dummy instrumented either with the Infra-Red Telescoping Rod for the Assessment of Chest Compression (IR-TRACC) or the RibEye? rib deflection measurement system.

Methods: The optical sensors of the RibEye system were used to capture the multipoint deformation of the dummy at frontal and rearward off-center locations in addition to the center of the rib location. The experimental setup consisted of 2 types of loadings: Low severity and high severity. Low-severity loading was performed by deploying a fixture-mounted side airbag on the dummy and high-severity loading was achieved by deploying a driver front airbag mounted in a similar fashion. The low-severity condition aimed at deforming the dummy’s ribs locally at off-center locations where the RibEye light emitting diodes (LEDs) were positioned to capture the deformations at those locations. The high-severity condition aimed at loading the dummy at high speed in lateral and oblique directions similar to what is experienced by dummies in side impacts.

Results: In the low-severity tests, the peak deflections, in terms of length change, were approximately 15–20?mm, whereas for the high-severity cases the peak deflections were in the range of 30–40?mm for both IR-TRACC and RibEye cases.

Conclusions: For similar physical insults, dummies with the IR-TRACC and RibEye systems showed varying results for both length changes and the shoulder forces depending on the severity and direction of loading. Under purely lateral loading, the mid-length changes with the RibEye and the 1D IR-TRACC were comparable. In the oblique loading conditions, more differences were seen with the 2 systems depending on the impact direction. The shoulder forces consistently differed between the 2 systems. In the frontal oblique low-severity cases, the ribs pivoted along the spine end and the length change was not found to be a suitable parameter to quantify rib deformation in such loading scenarios.     

Use of association rules to explore cause–effect relationships in occupational accidents in the Taiwan construction industry

Most models of the incidence of occupational accidents in the construction industry are composed of multiple factors. Although statistical techniques can be used to infer cause-and-effect relationships among these factors, the large number of factors involved and the complexity of the relationships among them make it difficult for managers to identify potential hazards in construction projects and thus develop effective safety procedures. This study addresses this problem by using the association-rule method of data mining in performing an analysis of 1347 accidents in the Taiwan construction industry during the period 2000–2007. The association-rule method enables potential cause-and-effect relationships to be identified among the many factors that play a role in occupational accidents in the construction industry. The study finds that such accidents tend to occur when certain combinations of hazards are present – especially working in high places without protective measures, loss of balance when in motion, failure to use protective equipment, insufficient experience, and injurious contact with unstable structures. These hazards are especially evident in small enterprises with less than 10 persons. The results can help management to formulate effective safety policies with regard to management shortcomings and staff training.     

Continued trends in older driver crash involvement rates in the United States: Data through 2017–2018

Introduction: With the growing older adult population due to the aging baby-boom cohort, there was concern that increases in fatal motor-vehicle crashes would follow. Yet, previous analyses showed this to be untrue. The purpose of this study was to examine current trends to determine if previous declines have persisted or risen with the recent increase in fatalities nationwide. Methods: Trends among drivers ages 70 and older were compared with drivers 35–54 for U.S. passenger vehicle fatal crash involvements per 100,000 licensed drivers from 1997 to 2018, fatal and all police-reported crash involvements per vehicle miles traveled using the 1995, 2001, 2009, and 2017 National Household Travel Surveys, and driver deaths per 1,000 crashes. Results: Since the mid-1990s, fatal crashes per licensed driver trended downward, with greater declines for drivers ages 70 and older than for middle-aged drivers (43% vs. 21%). Fatal crash rates per 100,000 licensed drivers and police-reported crash rates per mile traveled for drivers ages 70–79 are now less than those for drivers ages 35–54, but their fatal crash rates per mile traveled and risk of dying in a crash remain higher as they drive fewer miles. As the economy improved over the past decade, fatal crash rates increased substantially for middle-aged drivers but decreased or remained stable among older driver age groups. Conclusions: Fatal crash involvements for adults ages 70 and older has recently increased, but they remain down from their 1997 peak, even as the number of licensed older drivers and the miles they drive have increased. Health improvements likely contributed to long-term reductions in fatal crash rates. As older drivers adopt vehicles with improved crashworthiness and safety features, crash survivability will improve. Practical Application: Older adults should feel confident that their independent mobility needs pose less risk than previously expected.     

Trends in teen driver licensure,driving patterns and crash involvement in the United States, 2006–2015

IntroductionThe Monitoring the Future (MTF) survey provides nationally-representative annual estimates of licensure and driving patterns among U.S. teens. A previous study using MTF data reported substantial declines in the proportion of high school seniors that were licensed to drive and increases in the proportion of nondrivers following the recent U.S. economic recession.MethodTo explore whether licensure and driving patterns among U.S. high school seniors have rebounded in the post-recession years, we analyzed MTF licensure and driving data for the decade of 2006–2015. We also examined trends in teen driver involvement in fatal and nonfatal injury crashes for that decade using data from the Fatality Analysis Reporting System and National Automotive Sampling System General Estimates System, respectively.ResultsDuring 2006–2015, the proportion of high school seniors that reported having a driver's license declined by 9 percentage points (11%) from 81% to 72% and the proportion that did not drive during an average week increased by 8 percentage points (44%) from 18% to 26%. The annual proportion of black seniors that did not drive was consistently greater than twice the proportion of nondriving white seniors. Overall during the decade, 17- and 18-year-old drivers experienced large declines in fatal and nonfatal injury crashes, although crashes increased in both 2014 and 2015.ConclusionsThe MTF data indicate that licensure and driving patterns among U.S. high school seniors have not rebounded since the economic recession. The recession had marked negative effects on teen employment opportunities, which likely influenced teen driving patterns. Possible explanations for the apparent discrepancies between the MTF data and the 2014 and 2015 increases in crashes are explored.Practical applicationsMTF will continue to be an important resource for clarifying teen driving trends in relation to crash trends and informing strategies to improve teen driver safety.     

Smoke Suppession in Ploy (Vivngl Chloribe)

Polymeric materials are combustible in nature and poly (vtnyl chloride) is no ex-ception. Due to its high chlorine contents it is relatively fiame retardant, hawever be-cause of the processing aids such as plasttcizer etc. this advantage is lost. Duringburning the two main hazards of PVC are Hydrogen Chloride gas and copiousamount of smoke. Dtfferent methods for smoke suppression of polymers are also ap-plicable to the case of PVC. Complexes of dzfferent metal, mixedmetals and metalbased organics are discussed along with other methods of smoke suppression in PVC.Some aspects of smoke measurement have also been covered.     

Workers’ Involvement—A Missing Component in the Implementation of Occupational Safety and Health Management Systems in Enterprises

Effective implementation of occupational safety and health (OSH) legislation based on European Union directives requires promotion of OSH management systems ( OSH MS). To this end, voluntary Polish standards (PN-N-18000) have been adopted, setting forth OSH MS specifications and guidelines. However, the number of enterprises implementing OSH MS has increased slowly, falling short of expectations, which call for a new national policy on OSH MS promotion. To develop a national policy in this area, a survey was conducted in 40 enterprises with OSH MS in place. The survey was aimed at identifying motivational factors underlying OSH MS implementation decisions. Specifically, workers’ and their representatives’ involvement in OSH MS implementation was investigated. The results showed that the level of workers ‘ involvement was relatively low, which may result in a low effectiveness of those systems. The same result also applies to the involvement of workers’ representatives and that of trade unions.     

Gender differences in public office workers’ satisfaction,subjective symptoms and musculoskeletal complaints in workplace and office environments

This study investigates differences between male and female public office workers’ satisfaction levels, sick building syndrome (SBS) symptoms and musculoskeletal disorder (MSD) complaints in workplace and office environments. Questionnaire surveys were performed in 30 offices from 15 public institutions. Male and female workers of the same age were coupled and selected from each office, gathering a total of 120 male and 120 female subjects. The results show that differences exist between genders in noise and lighting satisfaction levels, SBS-related symptoms (eye, nose, skin) and MSD complaints of hand/wrist/finger, while there is no difference in overall satisfaction level of office environments. The study also suggests that office design for public office workers should take into account gender differences in preventing MSDs and also SBS. The findings of this study are expected to serve as basic data for designing effective public office environments.     

Safety Management in Coal Mines—Risk Assessment

The present state of accident hazard at work in the Polish mining industry is presented. A comparison is made of the accident indices in relation to other countries. A reference is made to the work safety management system implemented in the mines. Safety management is discussed in terms of risk management. On the basis of the natural death index and that of accidents at work, numerical scales are presented defining the limits of the inadmissable, tolerable, and acceptable risk. The course of variation of risk indices for fatal, serious, and minor accidents is evaluated. The results of the assessment for all kinds of accidents at work in the mining industry are presented.     

Study on Lockout Procedures for the Safety of Workers Intervening on Equipment in the Municipal Sector in Québec

In Québec, workers intervening in hazardous zones of machines, equipment and processes during maintenance, repairs and unjamming activities have to apply lockout procedures. Lockout procedures involve shutting down the equipment, isolating it, applying individual locks, releasing residual energies and verifying the absence of energies. Lockout has mostly been linked to industrial sectors. However, the municipal sector also faces challenges when it comes to controlling hazardous energies. The objectives of this research are to study serious accidents linked to our subject, study the application of lockout in different municipalities in Québec, identify the specificities for the municipal sector and propose some means to support the application of lockout. We will show that lockout procedures are required in different locations in municipalities and that they are currently being implemented in the municipal sector in Québec. Moreover, we propose a model which aims at facilitating the implementation of lockout procedures in the municipal sector.     

A framework addressing a safe ageing management in complex industrial sites: The Italian experience in «Seveso» establishments

In Europe, the Directive 2012/18/EU (Seveso III) strengthens the obligation to adopt a program assuring the integrity of critical equipment at major hazard establishments, by taking into account actual deterioration mechanisms (internal and external corrosion, erosion, thermal and mechanical fatigue, etc.). The program must cover all phases of the lifecycle and ensure a safe ageing of equipment, particularly when these are reaching the final stage of life. The effectiveness of the integrity program must be carefully assessed during the audits planned by the establishment's operator as well as by inspectors on behalf of the Competent Authorities. The adoption of a Risk Based Inspection scheme provides a valuable help to face this matter. The operator is, anyway, required a considerable effort to face at least three issues related to: (i) the understanding of concurring physical and chemical phenomena; (ii) the management of information associated with each individual component and its history, (iii) the appropriate measurement, including acquisition and management of data. There is a considerable difficulty in understanding these issues during Seveso inspections and external audits, because time and resources are often limited. For this reason, models and methods supporting the definition of the ageing status and trend in industrial sites are needed. This paper analyses the main factors affecting ageing. A framework for “ageing” assessment in complex industrial sites, including “Seveso” establishments, is proposed; then, its validation, by means of data collected during a testing phase carried out in Italy, is also given.