Experimental in situ chemical peroxidation of atrazine in contaminated soil

Lab-scale experiments of in situ chemical oxidation (ISCO), were performed on soil contaminated with 100 mg kg(-1) of atrazine (CIET). The oxidant used was hydrogen peroxide catalysed by naturally occurring minerals or by soluble Fe(II) sulphate, added in aqueous solution. The oxidation conditions were: CIET:H2O2=1:1100, 2 PV or 3 PV reaction volume, Fe(II):H2O2=0, 1:22, 1:11. Stabilized (with KH2PO4 at a concentration of 16 g l(-1)) or non-stabilized hydrogen peroxide was used. The pH of the reagents was adjusted to pH=1 with sulphuric acid, or was not altered. Results showed that the addition of soluble Fe(II) increased the temperature of the soil slurry and the use of stabilized hydrogen peroxide resulted in a lower heat generation. The treatment reduced the COD of the soil of about 40%, pH was lowered and natural organic matter became less hydrophobic. The highest atrazine conversion (89%) was obtained in the conditions: 3 PV, Fe(II):H2O2=1:11 with stabilized hydrogen peroxide added in two steps. The stabilizer only increased H2O2 life-time significantly when soluble Fe(II) was added. Results indicate as preferential degradation pathway of atrazine in soil dechlorination instead of dealkylation.     

Hydrogen peroxide photolysis, fenton reagent and photo-fenton for the degradation of nitrophenols: a comparative study

The kinetics of the degradation of seven nitrophenols (2-nitrophenol, 4-nitrophenol, 2,5-dinitrophenol, 2,6-dinitrophenol, 2,4-dinitrophenol, 2-methyl-4,6-dinitrophenol, 4-methyl-2,6-dinitrophenol) with the Fenton reagent, photo-Fenton, and hydrogen peroxide photolysis was investigated. The efficiency and operating costs for the studied treatments were evaluated and compared. The Fenton reagent was found to be the most efficient and the cheapest way for the nitrophenols (NPs) degradation. The formation of nitrate as a result of mineralisation of organically bounded nitrogen was observed during the treatment of NPs with studied treatment processes. The degrees of organically bounded nitrogen conversion to nitrate after 90% degradation of NPs with the Fenton, photo-Fenton and hydrogen peroxide photolysis were 51-67%, 85-90%, and 50-60%, respectively. According to Daphnia magna acute toxicity test, the Fenton treatment led to complete detoxification of NPs.     

Solar light induced and TiO2 assisted degradation of textile dye reactive blue 4

Aqueous solutions of reactive blue 4 textile dye are totally mineralised when irradiated with TiO2 photocatalyst. A solution containing 4 x 10(-4) M dye was completely degraded in 24 h irradiation time. The intensity of the solar light was measured using Lux meter. The results showed that the dye molecules were completely degraded to CO2, SO4(2-), NO3-, NH4+ and H2O under solar irradiation. The addition of hydrogen peroxide and potassium persulphate influenced the photodegradation efficiency. The rapidity of photodegradation of dye intermediates were observed in the presence of hydrogen peroxide than in its absence. The auxiliary chemicals such as sodium carbonate and sodium chloride substantially affected the photodegradation efficiency. High performance liquid chromatography and chemical oxygen demand were used to study the mineralisation and degradation of the dye respectively. It is concluded that solar light induced degradation of textile dye in wastewater is a viable technique for wastewater treatment.     

Singlet oxygen mediated degradation of Klason lignin

After some results concerning photochemical generated singlet oxygen on lignins from steam explosion, the reactions of chemically generated singlet oxygen with Klason lignins from pine and beech are described. Singlet oxygen was produced through the reaction of hydrogen peroxide with sodium hypochlorite. The degradation of lignin was followed by uv spectroscopy and gel permeation chromatography. Extensive degradation of the lignins was observed when 20 mg of Klason lignin was treated with 1 ml of 30% hydrogen peroxide and 8.56 ml of 1.093 M sodium hypochlorite. In the uv spectra registered after the treatment with singlet oxygen the absorptions typical of lignin (210-220 nm and 250-280 nm) were completely absent. The gpc analysis of lignin after a treatment with 0.1 ml of hydrogen peroxide and 0.86 ml of sodium hypochlorite showed a clear reduction of signals due to the lignin and a shift to lower molecular weight. The potential use of this procedure in the bleaching procedure was tested by using recycled paper. A maximum reduction of 51% in the amount of lignin in this paper was observed.     

Atrazine is not readily mineralised in 24 temperate soils regardless of pre-exposure to triazine herbicides

Mineralisation of atrazine in soil has been shown to depend on previous exposure of the herbicide. In this study, 24 Danish soils were collected and screened for potential to mineralise atrazine. Six soils were chosen, because they had never been exposed to atrazine, whereas 18 soils were chosen because of their history of application of atrazine or the related compound terbuthylazine. None of the 24 soils revealed a mineralisation potential of more than 4% of the added atrazine within a 60 day timeframe. In an atrazine adapted French soil, we found 60% mineralisation of atrazine in 30 days. Cattle manure was applied in order to boost the microbial activity, and a 2-3% increase in the atrazine mineralisation was found in some of the temperate soils, while in the highly adapted French soil it caused a 5% reduction.     

Fe (III) supported on resin as effective catalyst for the heterogeneous oxidation of phenol in aqueous solution

FeIII supported on resin as an effective catalyst for oxidation was prepared and applied for the degradation of aqueous phenol. Phenol was selected as a model pollutant and the catalytic oxidation was carried out in a batch reactor using hydrogen peroxide as the oxidant. The influent factors on oxidation, such as catalyst dosage, H2O2 concentration, pH, and phenol concentration were examined by considering both phenol conversion and chemical oxygen demand (COD) removal. The FeIII-resin catalyst possesses a high oxidation activity for phenol degradation in aqueous solution. The experimental results of this study show that almost 100% phenol conversion and over 80% COD removal can be achieved with the FeIII-resin catalyst catalytic oxidation system. A series of prepared resin were investigated for improving the oxidation efficiency. It was found that the reaction temperature and initial pH in solution significantly affected both of phenol conversion and COD removal efficiency. The activity of the catalyst significantly decreased at high pH, which was similar to the Fenton-like reaction mechanism. Results in this study indicate that the FeIII-resin catalytic oxidation process is an efficient method for the treatment of phenolic wastewater.     

The role of ferrous ion in Fenton and photo-Fenton processes for the degradation of phenol

The efficiency of different Fenton-related oxidative processes such as Fenton, solar-Fenton and UV-Fenton were examined using phenol as a model compound in simulated and industrial wastewater. A batch study was conducted to optimize parameters like pH, hydrogen peroxide concentration and ferrous ion concentration governing the Fenton process. At optimum conditions, different Fenton-related processes were compared for the degradation of phenol. Increased degradation and mineralisation efficiency were observed in photo-Fenton processes as compared to conventional Fenton process. The maximum mineralising efficiency for phenol with Fenton, solar and UV-Fenton processes were 41%, 96% and 97% respectively. In Fenton process, carboxylic acids like acetic acid and oxalic acid were formed as end products during the degradation of phenol while in photo-Fenton processes, both these ions were identified during the early stages of phenol degradation and were oxidized almost completely at 120 min of the reaction time. In photo-Fenton processes (solar and UV light) complete degradation were observed with 0.4 mM of Fe2+ catalyst as compared to 0.8 mM of Fe2+ in conventional Fenton process. In Fenton and solar-Fenton processes, an iron reusability study was performed to minimize the amount of iron used in treatment process. The efficacy of Fenton and solar-Fenton processes was applied to effluent from phenol resin-manufacturing unit for the removal and mineralisation of phenol.     

Sonochemical degradation of a pharmaceutical waste,atenolol, in aqueous medium

Atenolol is a β-blocker drug and an identified emerging pollutant. Advanced oxidation processes (AOPs) utilise the reaction of a highly oxidising species (hydroxyl radicals, ^?OH) for the mineralisation of emerging pollutants since conventional treatment methodologies generally fail to degrade these compounds. In the present work, degradation of atenolol was carried out using ultrasound with frequencies ranging from 200 kHz to 1 MHz as a source of hydroxyl radical. The degradation was monitored by HPLC, total organic carbon (TOC) and chemical oxygen demand (COD) reduction and ion chromatography (IC). Nearly 90 % of degradation of atenolol was observed with ultrasound having 350 kHz. Both frequency and power of ultrasound affect the efficiency of degradation. Nearly 100 % degradation was obtained at a pH of 4. Presence of various additives such as sodium dodecyl sulphate, chloride, sulphate, nitrate, phosphate and bicarbonate was found to reduce the efficiency of degradation. Although nearly 100 % degradation of atenolol was observed under various experimental conditions, only about 62 % mineralisation (from TOC and COD measurements) was obtained. Nearly eight intermediate products were identified using high-resolution mass spectrometry (LC-Q-TOF). These products were understood as the results of hydroxyl radical addition to atenolol. The degradation studies were also carried out in river water which also showed a similar degradation profile. A mechanism of degradation and mineralisation is presented.     

Bioremediation of chlorobenzene-contaminated ground water in an in situ reactor mediated by hydrogen peroxide

New in situ reactive barrier technologies were tested nearby a local aquifer in Bitterfeld, Saxonia-Anhalt, Germany, which is polluted mainly by chlorobenzene (CB), in concentrations up to 450 microM. A reactor filled with original aquifer sediment was designed for the microbiological remediation of the ground water by indigenous bacterial communities. Two remediation variants were examined: (a) the degradation of CB under anoxic conditions in the presence of nitrate; (b) the degradation of CB under mixed electron acceptor conditions (oxygen+nitrate) using hydrogen peroxide as the oxygen-releasing compound. Under anoxic conditions, no definite degradation of CB was observed. Adding hydrogen peroxide (2.94 mM) and nitrate (2 mM) led to the disappearance of CB (ca. 150 microM) in the lower part of the reactor, accompanied by a strong increase of the number of cultivable aerobic CB degrading bacteria in reactor water and sediment samples, indicating that CB was degraded mainly by productive bacterial metabolism. Several aerobic CB degrading bacteria, mostly belonging to the genera Pseudomonas and Rhodococcus, were isolated from reactor water and sediments. In laboratory experiments with reactor water, oxygen was rapidly released by hydrogen peroxide, whereas biotic-induced decomposition reactions of hydrogen peroxide were almost four times faster than abiotic-induced decomposition reactions. A clear chemical degradation of CB mediated by hydrogen peroxide was not observed. CB was also completely degraded in the reactor after reducing the hydrogen peroxide concentration to 880 microM. The CB degradation completely collapsed after reducing the hydrogen peroxide concentration to 440 microM. In the following, the hydrogen peroxide concentrations were increased again (to 880 microM, 2.94 mM, and 880 microM, respectively), but the oxygen demand for CB degradation was higher than observed before, indicating a shift in the bacterial population. During the whole experiment, nitrate was uniformly reduced during the flow path in the reactor.     

Degradation mechanisms of 4-chlorophenol in a novel gas-liquid hybrid discharge reactor by pulsed high voltage system with oxygen or nitrogen bubbling

The effect of gas bubbling on the removal efficiency of 4-chlorophenol (4-CP) in aqueous solution has been investigated using a novel pulsed high voltage gas-liquid hybrid discharge reactor, which generates gas-phase discharge above the water surface simultaneously with the spark discharge directly in the liquid. The time for 100% of 4-CP degradation in the case of oxygen bubbling (7 min) was much shorter than that in the case of nitrogen bubbling (25 min) as plenty of hydrogen peroxide and ozone formed in oxygen atmosphere enhanced the removal efficiency of 4-CP. Except for the main similar intermediates (4-chlorocatechol, hydroquinone and 1,4-benzoquinone) produced in the both cases of oxygen and nitrogen bubbling, special intermediates (5-chloro-3-nitropyrocatechol, 4-chloro-2-nitrophenol, nitrate and nitrite ions) were produced in nitrogen atmosphere. The reaction pathway of 4-CP in the case of oxygen bubbling was oxygen/ozone attack on the radical hydroxylated derivatives of 4-CP. However, in the case of nitrogen bubbling, hydroxylation was the main reaction pathway with effect of N atom on degradation of 4-CP.     

Hydrogen peroxide mediated photodegradation of phenol as studied by a flash photolysis/HPLC technique

The technique of flash photolysis followed by high-performance liquid chromatography has been applied to the study of the photodegradation of phenol (I) in the presence of hydrogen peroxide. Progress of the reaction of I (0.1 mM) in undegassed aqueous solution ([H2O2]/[I] = 200/l) was observed by using multiple flashes (16 J). Analysis after a single flash indicated that catechol and hydroquinone were the primary products of the reaction. The reaction was found to be independent of pH in the range 7.0-9.0, but the yield of degradation decreased at pH > 9.0 and at pH < 7.0. The effects of the hydrogen peroxide concentration and flash energy on the chemical yield of the pollutant degradation, and product formation, were investigated as well. The mechanism of the reaction is discussed. A possibility of the application of flashlamps as powerful sources of the UV irradiation in industrial reactors for wastewater treatment is suggested.     

Degradation of atrazine in mineral salts medium and soil using enrichment culture

Atrazine degrading enrichment culture was prepared by its repeated addition to an alluvial soil and its ability to degrade atrazine in mineral salts medium and soil was studied. Enrichment culture utilized atrazine as a sole source of carbon and nitrogen in mineral salts medium and degradation slowed down when sucrose and/or ammonium hydrogen phosphate were supplemented as additional source of carbon and nitrogen, respectively. Biuret was detected as the only metabolite of atrazine while deethylatrazine, deisopropyatrazine, hydroxyatrazine and cyanuric acid were never detected at any stage of degradation. Enrichment culture degraded atrazine in an alkaline alluvial soil while no degradation was observed in the acidic laterite soil. Enrichment culture was able to withstand high concentrations of atrazine (110 μg/g) in the alluvial soil as atrazine was completely degraded. Developed mixed culture has the ability to degrade atrazine and has potential application in decontamination of contaminated water and soil.     

Using polymer mats to biodegrade atrazine in groundwater: laboratory column experiments

Large-scale column experiments were undertaken to evaluate the potential of in situ polymer mats to deliver oxygen into groundwater to induce biodegradation of the pesticides atrazine, terbutryn and fenamiphos contaminating groundwater in Perth, Western Australia. The polymer mats, composed of woven silicone (dimethylsiloxane) tubes and purged with air, were installed in 2-m-long flow-through soil columns. The polymer mats proved efficient in delivering dissolved oxygen to anaerobic groundwater. Dissolved oxygen concentrations increased from <0.2 mg l(-1) to approximately 4 mg l(-1). Degradation rates of atrazine in oxygenated groundwater were relatively high with a zero-order rate of 240-380 microg l(-1) or a first-order half-life of 0.35 days. Amendment with an additional carbon source showed no significant improvement in biodegradation rates, suggesting that organic carbon was not limiting biodegradation. Atrazine degradation rates estimated in the column experiments were similar to rates determined in laboratory culture experiments, using pure cultures of atrazine-mineralising bacteria. No significant degradation of terbutryn or fenamiphos was observed under the experimental conditions within the time frames of the study. Results from these experiments indicate that remediation of atrazine in a contaminated aquifer may be achievable by delivery of oxygen using an in situ polymer mat system.     

Fe/活性炭多相类Fenton法湿式氧化罗丹明B废水的研究

采用自制的Fe/活性炭（Fe/AC）为催化剂,H₂O₂为氧化剂,组成多相类Fenton试剂催化降解罗丹明B染料废水。实验结果表明,在催化剂加入量为0.8 g/L,H₂O₂体积分数为0.3%,废水pH值为13,反应时间为30 min的条件下,质量浓度为200 mg/L的罗丹明B染料废水的脱色率达100%。反应动力学研究表明,罗丹明B脱色反应近似为一级反应,30℃时反应速率常数为0.02675 min^-1,表观活化能为69.47 kJ/mol。     

An assessment of the suitable operating conditions for the CeO2/gamma-Al2O3 catalyzed wet air oxidation of phenol

It has been shown that the CeO2/gamma-Al2O3 catalyst is a feasible alternative to CeO2 for the catalytic wet air oxidation (CWAO) of phenol because it remains an effective catalyst and yet is cheaper to prepare. In this study, we found that the optimal cerium content in the CeO2/gamma-Al2O3 catalyst was 20 wt.%, regardless of catalyst loading. Furthermore, at 180 degrees C, with a phenol concentration of 1000 mg l(-1), and an O2 partial pressure of 1.0M Pa or 1.5M Pa, the optimal catalyst loading was 3.0 gl (-1). The efficacy of CWAO of phenol improved with O2 partial pressure, although the effects of O2 pressure were more significant between 0.5 MPa and 1.5 MPa than between 1.5 MPa and 2.0 MPa. After 2 h of reaction, approximately 100% phenol conversion and 80% total organic carbon (TOC) removal was recorded at 180 degrees C, 1000 mg l(-1) of phenol and 3.0 g l(-1) of catalyst. Because these percentages subsequently leveled off, it is suggested that 2 h is a suitable time over which to run the reaction. The efficacy of CWAO of phenol decreased as initial phenol concentration was raised (from 400 to 2500 mg l(-1)), with the exception of phenol conversion after about 2 h, for which 400 mg l(-1) produced the lowest phenol conversion figure. Higher phenol concentrations require both catalyst loading and O2 partial pressure to be increased to maintain high performance. For example, for 2000 mg l(-1) and 2500 mg l(-1) phenol, nearly 100% phenol conversion and 90% TOC removal after 4 h of reaction at 180 degrees C required 4.0 g l(-1) of catalyst and 2.0 MPa.     

Non-degradable triazine substrates of atrazine and cyanuric acid hydrothermally and in supercritical water under the UV-illuminated photocatalytic cooperation

Strong oxidation by titanium dioxide photocatalysis can occur by photodegradation of organic contaminants in air and water. Some endocrine disruptors such as 2,4-dichlorophenoxy acetic acid (;;; ), 2,4-dichlorophenol (;;; ), nonylphenol (; ), bisphenol A (), diethyl phthalate (; ), etc. which can be neither biodegraded by bacteria nor degraded thermally can be degraded by TiO(2) photocatalytic treatment. However, incomplete photomineralization partly occurred, when TiO(2) photocatalytic degradation is employed for the treatment of certain endocrine disruptors. For example, no atrazine pesticide having triazine skeleton can be completely mineralized even by a photocatalytic procedure; the photodegradation of atrazine ultimately stops at the intermediate step of cyanuric acid, which cannot be photodegraded even after long illumination times ().In this study, the decomposition of atrazine and cyanuric acid was carried out with a device combining photocatalytic degradation in supercritical water (scH(2)O) or hydrothermal water (hyH(2)O). Atrazine and cyanuric acid can be degraded by the cooperation of either scH(2)O or hyH(2)O and UV illuminated TiO(2)-photocatalytic dispersed system under the fixed pressure of 23 MPa at 623 K or 683 K in a 120-ml Hastelloy batch reactor. The photocatalytic degradation method under high temperature and pressure has found appropriate for the photocatalytic oxidation of acetic acid and 2-chlorobiphenyl under continuous flow conditions at 160 degrees C and 20 atm (). In addition, the wet peroxide oxidation of PCBs by high temperature and pressure has been reported (). The main aims of this research are following. (i): the degradation of atrazine and cyanuric acid within the scH(2)O or hyH(2)O, (ii) the decomposition of atrazine and cyanuric acid catalyzed by TiO(2) particles under scH(2)O or hyH(2)O, and the synergistic effect for several reactions with TiO(2) and scH(2)O or hyH(2)O, and (iii) the mineralization yield of nitrogen and chlorine atoms concerning the chemical structures of atrazine or cyanuric acid (only nitrogen).     

Photocatalytic degradation of the herbicide pendimethalin using nanoparticles of BaTiO3/TiO2 prepared by gel to crystalline conversion method: a kinetic approach

Photocatalytic degradation of the herbicide, pendimethalin (PM) was investigated with BaTiO3/TiO2 UV light system in the presence of peroxide and persulphate species in aqueous medium. The nanoparticles of BaTiO3 and TiO2 were obtained by gel to crystallite conversion method. These photo catalysts are characterized by energy dispersive x-ray analysis (EDX), scanning electron microscope (SEM), x-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) adsorption isotherm and reflectance spectral studies. The quantum yields for TiO2 and BaTiO3 for the degradation reactions are 3.166 Einstein m(-2) s(-1) and 2.729 Einstein m(-2) s(-1) and catalytic efficiencies are 6.0444 x 10(-7) mg(-2)h(-1)L2 and 5.403 x 10(-7) mg(-2)h(-1)L2, respectively as calculated from experimental results. BaTiO3 exhibited comparable photocatalytic efficiency in the degradation of pendimethalin as the most widely used TiO2 photocatalyst. The persulphate played an important role in enhancing the rate of degradation of pendimethalin when compared to hydrogen peroxide. The degradation process of pendimethalin followed the first-order kinetics and it is in agreement with Langmuir-Hinshelwood model of surface mechanism. The reason for high stability of pendimethalin for UV-degradation even in the presence of catalyst and oxidizing agents were explored. The higher rate of degradation was observed in alkaline medium at pH 11. The degradation process was monitored by spectroscopic techniques such as ultra violet-visible (UV-Vis), infrared (IR) and gas chromatography mass spectroscopy (GC-MS). The major intermediate products identified were: N-propyl-2-nitro-6-amino-3, 4-xylidine, (2, 3-dimethyl-5-nitro-6-hydroxy amine) phenol and N-Propyl-3, 4-dimethyl-2, 6-dinitroaniline by GC-MS analysis and the probable reaction mechanism has been proposed based on these products.     

Atrazine removal by ozonation processes in surface waters

Atrazine (6-chloro-N-ethyl-N'-isopropyl-1,3,5-triazinedyl-2,4-diamine) was treated with ozone alone and in combination with hydrogen peroxide or UV radiation in three surface waters. Experiments were carried out in two bubble reactors operated continuously. Variables investigated were the ozone partial pressure, temperature, pH, mass flow ratio of oxidants fed: hydrogen peroxide and ozone and the type of oxidation including UV radiation alone. Residence time for the aqueous phase was kept at 10 min. Concentrations of some intermediates, including deethylatrazine, deisopropylatrazine and deethyldeisopropylatrazine, were also followed. The nature of water, specifically the alkalinity and pH were found to be important variables that affected atrazine (ATZ) removal. Surface waters with low alkalinity and high pH allowed the highest removal of ATZ to be reached. There was an optimum hydrogen peroxide to ozone mass flow ratio that resulted in the highest ATZ removal in each surface water treated. This optimum was above the theoretical stoichiometry of the process. Therefore, to reach the maximum removal of ATZ in a O3/H2O2 process, more hydrogen peroxide was needed in the surface waters treated than in ultrapure water under similar experimental conditions. In some cases, UV radiation alone resulted in the removal of ATZ higher than ozonation alone. This was likely due to the alkalinity of the surface water. Ozonation and UV radiation processes yield different amounts of hydrogen peroxide. Combined ozonations (O3/H2O2 and O3/UV) lead to ATZ removals higher than single ozonation or UV radiation but the formation of intermediates was higher.     

Fresnel lens to concentrate solar energy for the photocatalytic decoloration and mineralization of orange II in aqueous solution

The decoloration and mineralization of the azo dye orange II under conditions of artificial ultraviolet light and solar energy concentrated by a Fresnel lens in the presence of hydrogen peroxide and TiO(2)-P25 was studied. A comparative study to demonstrate the viability of this solar installation was done to establish if the concentration reached in the focus of the Fresnel lens was enough to improve the photocatalytic degradation reaction. The degradation efficiency was higher when the photolysis was carried out under concentrated solar energy irradiation as compared to UV light source in the presence of an electron acceptor such us H(2)O(2) and the catalyst TiO(2). The effect of hydrogen peroxide, pH and catalyst concentration was also determined. The increase of H(2)O(2) concentration until a critical value (14.7 mM) increased both the solar and artificial UV oxidation reaction rate by generating hydroxyl radicals and inhibiting the (e(-)/h(+)) pair recombination, but the excess of hydrogen peroxide decreases the oxidation rate acting as a radical or hole scavenger and reacting with TiO(2) to form peroxo-compounds, contributing to the inhibition of the reaction. The use of the response surface methodology allowed to fit the optimal values of the parameters pH and catalyst concentration leading to the total solar degradation of orange II. The optimal pH range was 4.5-5.5 close to the zero point charge of TiO(2) depending on surface charge of catalyst and dye ionization state. Dosage of catalyst higher than 1.1 gl(-1) decreases the degradation efficiency due to a decrease of light penetration.     

The importance of atmospheric ozone and hydrogen peroxide in oxidising sulphur dioxide in cloud and rainwater

The process by which sulphur dioxide is oxidised in atmospheric droplets has been studied in laboratory experiments designed to collect a large amount of chemical data pertinent to the atmospheric situation. Thus the oxidation of sodium sulphite solutions by oxygen, ozone and hydrogen peroxide has been studied at different pH's and temperatures. In all cases the reaction is first order with respect to sulphite ion but the order with respect to oxidant differs. For oxygen the order is zero whereas the order for ozone and hydrogen peroxide is one. Varying the hydrogen ion concentration has little effect on the oxygen reaction rate between pH 6 and 9; the ozone reaction rate is inversely proportional to the square root of the hydrogen ion concentration and the hydrogen peroxide rate is almost directly proportional to the hydrogen ion concentration. These last two observations are very important since in the case of ozone it indicates that the reaction proceeds via a free radical mechanism involving hydroxyl radicals and in the case of hydrogen peroxide it is the only oxidation process of sodium sulphite so far investigated that shows a positive response to the presence of hydrogen ions.The experimental data was used to calculate the rate of sulphate formation in water droplets under atmospheric conditions for each of the three oxidants. If it is assumed that the ozone and hydrogen peroxide gas phase concentrations are initially 50 parts in 10⁹ and 1 part in 10⁹ by volume respectively, then the rates of sulphate formation are equal in cloud water at pH 5.8. Above this pH the ozone reaction is faster and below it the hydrogen peroxide reaction is faster due to the positive catalysis by hydrogen ions; the oxygen rate is unimportant by comparison at all pH's below 7. The rate of hydrogen peroxide reaction is such that substantial amounts of sulphate can still be formed rapidly in water droplets at pH values from 3 to 5, and thus this process will be very important in creating acidity in rainwater.