Development of an immunochromatographic assay for the rapid detection of bromoxynil in water

A rapid immunochromatographic one-step strip test was developed to specifically determine bromoxynil in surface and drinking water by competitive inhibition with the nano colloidal gold-conjugated monoclonal antibody (mAb). Bromoxynil standard samples of 0.01–10 mg L⁻¹ in water were tested by this method and the visual limit was 0.06 mg L⁻¹. The assay only required 5 min and one-step by dispensing a drop of sample solution onto a strip. Parallel analysis of water samples with bromoxynil showed comparable results from one-step strip test and ELISA. Therefore, the one-step strip test is very useful as a screening method for qualitative detection of bromoxynil in water.     

A rapid and high-throughput quantum dots bioassay for monitoring of perfluorooctane sulfonate in environmental water samples

Currently HPLC/MS is the state of the art tool for environmental/drinking water perfluorooctane sulfonate (PFOS) monitoring. PFOS can bind to peroxisomal proliferator-activated receptor-alpha (PPARα), which forms heterodimers with retinoid X receptors (RXRs) and binds to PPAR response elements. In this bioassay free PFOS in water samples competes with immobilized PFOS in ELISA plates for a given amount of PPARα-RXRα. It can be determined indirectly by immobilizing PPARα-RXRα-PFOS complex to another plate coated with PPARα antibody and subsequent measuring the level of PPARα-RXRα by using biotin-modified PPARα-RXRα probes-quantum dots-streptavidin detection system. The rapid and high-throughput bioassay demonstrated a detection limit of 2.5 ng L⁻¹ with linear range between 2.5 ng L⁻¹ and 75 ng L⁻¹. Detection results of environmental water samples were highly consistent between the bioassay and HPLC/MS.     

A competitive indirect enzyme-linked immunoassay for lead ion measurement using mAbs against the lead-DTPA complex

Immunoassays for quantitative measurement of environmental heavy metals offer several advantages over other traditional methods. To develop an immunoassay for lead, Balb/c mice were immunized with a lead-chelate-protein conjugate to allow maximum exposure of the metal to the immune system. Three stable hybridoma cell lines were obtained through spleen cells fusion with Sp2/0 cells. One cell line, 2A11D11, produced mAbs with preferential selectivity and sensitivity for Pb-DTPA than DTPA, exhibiting an affinity constant of 3.34 ± 0.24 × 10⁹ M⁻¹. Cross reactivity (CR) with other metals were below 1%, except for Fe(III) with a CR less than 5%. This quantitative indirect ELISA for the lead ion was used to detect environmental lead content in local water sources; importantly, the results from the immunoassay were in excellent agreement with those from ICP-MS. Development of immunoassays for metal ions may thus facilitate the detection and regulation of environmental pollution.     

Ultrafine particles at three different sampling locations in Taiwan

Atmospheric ultrafine particles (UPs or PM_0.1) were investigated at the roadside of Syuefu road in Hsinchu city, in the Syueshan highway tunnel in Taipei and in the NTU Experimental Forest in Nantou, Taiwan. A SMPS (TSI 3936) and three MOUDIs (MSP 110) were collocated to determine the number and mass concentrations of the PM_0.1 simultaneously. The filter samples were further analyzed for organic carbon (OC), element carbon (EC), water-soluble ions and trace elements. Taking into account the OC artifact of PM_0.1, good chemical mass closure (ratio of the reconstructed chemical mass to the gravimetrical mass of PMs) was obtained with an unknown percentage of 10.6, 26.2 and 37.2% at the roadside, tunnel and forest, respectively. The unexplained mass was attributed to aerosol water in this study. The artifact at the roadside, tunnel and the forest PM_0.1 mass was found to be as high as 51.6 ± 10.7%, 20.0 ± 5.4% and 85.6 ± 18.4%, respectively. Finally, the effective density of the roadside, tunnel and forest PM_0.1 was calculated based on the results of chemical speciation and found to be 1.45, 1.29 and 1.22 g cm^?3, respectively, which was in good agreement with that obtained by using the method of Spencer et al. (2007). Based on these results, it is foreseeable that the number concentration of the SMPS can be converted using the effective density determined by Spencer et al. (2007) for the real time measurement of the PM_0.1 concentration.     

A simple inexpensive gas phase chemiluminescence analyzer for measuring trace levels of arsenic in drinking water

An inexpensive sensitive gas-phase chemiluminescence (GPCL) based analyzer for arsenic is described; this device utilizes manual fluid dispensing operations to reduce size, weight and cost. The analyzer in its present form has a limit of detection (LOD, S/N = 3) of 1.0 μg/L total inorganic As (peak heightbased, 3 mL sample). The system was used to measure low level arsenic in tap water samples from Texas and New Mexico and compared with results obtained by inductively coupled plasma-mass spectrometry (ICP-MS) as well as those from an automated GPCL analyzer. Good correlations were observed. Higher levels of As (50-500 μg/L, As(III), As(V) and mixtures thereof) were spiked into local tap water; the recoveries ranged from 95 ± 2% to 101 ± 1%. A single instrument weighs less than 3 kg, consumes <25 W in power, can be incorporated in a briefcase and constructed for <$US $1000. It is easily usable in the field.     

Evaluation of airborne particulate matter and metals data in personal,indoor and outdoor environments using ED-XRF and ICP-MS and co-located duplicate samples

Factors and sources affecting measurement uncertainty associated with monitoring metals in airborne particulate matter (PM) were investigated as part of the Windsor, Ontario Exposure Assessment Study (WOEAS). The assessment was made using co-located duplicate samples and a comparison of two analytical approaches: ED-XRF and ICP-MS. Sampling variability was estimated using relative percent difference (RPD) of co-located duplicate samples. The comparison of ICP-MS and ED-XRF results yields very good correlations (R² ≥ 0.7) for elements present at concentrations that pass both ICP-MS and ED-XRF detection limits (e.g. Fe, Mn, Zn, Pb and Cu). PM concentration ranges (median, sample number) of 24-h indoor PM₁₀ and personal PM₁₀ filters, and outdoor PM_2.5 filters were determined to be 2.2–40.7 (11.0, n = 48) μg m^?3, 8.0–48.3 (11.9, n = 48) μg m^?3, and 17.1–42.3 (21.6, n = 18) μg m^?3, respectively. The gravimetric analytical results reveal that the variations in PM mass measurements for same-day sampling are insignificant compared to temporal or spatial variations: 92%, 100% and 96% of indoor, outdoor and personal duplicate samples, respectively, pass the quality criteria (RPD ≤ 20%). Uncertainties associated with ED-XRF elemental measurements of S, Ca, Mn, Fe and Zn for 24-h filter samples are low: 78%–100% of the duplicate samples passed the quality criteria. In the case of 24-h filter samples using ICP-MS, more elements passed the quality criteria due to the lower detection limits. These were: Li, Na, K, Ca, Si, Al, V, Fe, Mn, Co, Cu, Mo, Ag, Zn, Pb, As, Mg, Sb, Sn, Sr, Th, Ti, Tl, and U. Low air concentrations of metals (near or below instrumental detection limits) and/or inadvertent introduction of metal contamination are the main causes for excluding elements based on the pass/fail criteria. Uncertainty associated with elemental measurements must be assessed on an element-by-element basis.     

Soil water and particle size distribution influence laboratory-generated PM10

Management of soils to reduce the amount of PM₁₀ emitted during agricultural tillage operations is important for attainment of air quality standards in California's San Joaquin Valley (SJV). The purpose of this study was to improve and expand upon earlier work of predicting tillage-generated dust emissions based on soil properties. We focus on gravimetric soil water content (GWC) and soil texture. A mechanical laboratory dust generator was used to test 23 soils collected for this study. Averaged results showed PM₁₀ concentrations (mg m^?3) increased logarithmically as GWC decreased below soil water potentials of ?1500 kPa. Soils with clay contents less than about 10% by weight began to emit PM₁₀ at GWCs 1.5–4 times their GWC at ?1500 kPa. Soils with clay contents greater than about 10% began to emit PM₁₀ at GWC values closer to ?1500 kPa. We found no correlation between maximum PM₁₀ concentrations, measured at low GWC values, and the %sand, %silt, or %clay in a soil. However, there was a significant correlation between the %silt to %clay ratio and PM₁₀ concentrations. This not only suggests the dependence of dust emission magnitudes on the supply of particles of PM₁₀ size, but also the importance of clay in stabilizing aggregates and maintaining higher amounts of capillary water at lower water potentials. Based on modeled results of pooled data, PM₁₀ concentrations increased linearly (slope = 564) for every unit increase in the %silt to %clay ratio. However, when soils were separated into groups based on clay content, the slopes for PM₁₀ concentrations vs. %silt to %clay ratio were texture dependent. The slope for soils with <10% clay (slope = 727) was 3.3 times greater than for soils with >20% clay (slope = 221). Improved PM₁₀ emission prediction based on soil properties should improve management decisions aimed at reducing tillage-generated PM₁₀.     

Chronic toxicity of ZnO nanoparticles, non-nano ZnO and ZnCl2 to Folsomia candida (Collembola) in relation to bioavailability in soil

The chronic toxicity of zinc oxide nanoparticles (ZnO-NP) to Folsomia candida was determined in natural soil. To unravel the contribution of particle size and free zinc to NP toxicity, non-nano ZnO and ZnCl₂ were also tested. Zinc concentrations in pore water increased with increasing soil concentrations, with Freundlich sorption constants K_f of 61.7, 106 and 96.4 l/kg (n = 1.50, 1.34 and 0.42) for ZnO-NP, non-nano ZnO and ZnCl₂ respectively. Survival of F. candida was not affected by ZnO-NP and non-nano ZnO at concentrations up to 6400 mg Zn/kg d.w. Reproduction was dose-dependently reduced with 28-d EC50s of 1964, 1591 and 298 mg Zn/kg d.w. for ZnO-NP, non-nano ZnO and ZnCl₂, respectively. The difference in EC50s based on measured pore water concentrations was small (7.94-16.8 mg Zn/l). We conclude that zinc ions released from NP determine the observed toxic effects rather than ZnO particle size.     

Facile fabrication of green nano pure CeO2 and Mn-decorated CeO2 with Cassia angustifolia seed extract in water refinement by optimal photodegradation kinetics of malachite green

To eradicate the aquatic pollution caused by dyes, trendily the global researchers provide dedication to dye degradation using nanostructured photocatalyst. This research work is dedicated to explore an advanced, facile, bio-compact green fabricated nanostructure for water refinement. In this regard, plant-mediated syntheses of pure CeO₂ and Mn-decorated CeO₂ nano-powders have been inspected using seed extract of Cassia angustifolia. Investigations through UV-diffuse reflectance spectroscopy explored the significantly tuned band gap of Mn:CeO₂. FT-IR spectroscopy shows the existing functional groups of high-potential phenolic compounds, proteins, and amino acids in Cassia angustifolia act as reducing and capping agents involved in the green fabricated nanostructured samples. X-ray diffraction pattern has been exposed to crystalline cubic fluorite morphology in a single phase and it leads to a regulated optimized amount of Mn on CeO₂ nanostructure. The FESEM analysis predicts the morphology of CeO₂ in spherical and Mn:CeO₂ in flower-like structure. The HRTEM analysis has portrayed particle size of CeO₂ is 11 nm and tuned Mn:CeO₂ nanostructure is 9 nm. The HRTEM images revealed the average particle size in the range 10–12 nm in CeO₂ and 8–9 nm in 5 mol% Mn:CeO₂ nanoparticles. It showed a decrease in average particle size with an increase in Mn concentration and the reduction in size may be due to the replacement of Ce(IV) with Mn(II) ions. The elemental composition in nanostructure was predicted using energy-dispersive X-ray analysis. The rapid photocatalytic degradation efficiency of malachite green was effectually performed and compared with the kinetics model of Mn:CeO₂ and pure CeO₂ nanostructures. From the augmented results, tuned Mn:CeO₂ was found to act as the finest green fabricated photocatalyst in the amputation of lethal and carcinogenic dye.

     

Measurement and analysis of atmospheric concentrations of isoprene and its reaction products in central Texas

A field experiment was conducted in August 1998 to investigate the concentrations of isoprene and isoprene reaction products in the surface and mixed layers of the atmosphere in Central Texas. Measured near ground-level concentrations of isoprene ranged from 0.3 (lower limit of detection – LLD) to 10.2 ppbv in rural regions and from 0.3 to 6.0 ppbv in the Austin urban area. Rural ambient formaldehyde levels ranged from 0.4 ppbv (LLD) to 20.0 ppbv for 160 rural samples collected, while the observed range was smaller at Austin (0.4–3.4 ppbv) for a smaller set of samples (37 urban samples collected). Methacrolein levels did not vary as widely, with rural measurements from 0.1 ppbv (LLD) to 3.7 ppbv and urban concentrations varying between 0.2 and 5.7 ppbv. Isoprene flux measurements, calculated using a simple box model and measured mixed-layer isoprene concentrations, were in reasonable agreement with emission estimates based on local ground cover data. Ozone formation attributable to biogenic hydrocarbon oxidation was also calculated. The calculations indicated that if the ozone formation occurred at low VOC/NO_x ratios, up to 20 ppbv of ozone formed could be attributable to biogenic photooxidation. In contrast, if the biogenic hydrocarbon reaction products were formed under low NO_x conditions, ozone production attributable to biogenics oxidation would be as low as 1 ppbv. This variability in ozone formation potentials implies that biogenic emissions in rural areas will not lead to peak ozone levels in the absence of transport of NO_x from urban centers or large rural NO_x sources.     

Bioanalytical and instrumental analysis of estrogenic activities in drinking water sources from Yangtze River Delta

The estrogenic activities of source water from Yangtze River, Huaihe River, Taihu Lake and groundwater in Yangtze River Delta in the dry and wet season were determined by use of reporter gene assays based on African green monkey kidney (CV-1) cell lines. Higher estrogenic activities were observed in the dry season, and the estrogenic potentials in water samples from Taihu Lake were greater than other river basins. None of the samples from groundwater showed estrogen receptor (ER) agonist activity. The 17β-Estradiol (E2) equivalents (EEQs) of water samples in the dry season ranged from 9.41 × 10^?1 to 1.20 × 10¹ ng E2 L^?1. In the wet season, EEQs of all the water samples were below the detection limit as 9.00 × 10^?1 ng E2 L^?1 except for one sample from Huaihe River. The highest contribution of E2 was detected in Yangtze River as 99% of estrogenic activity. Nonylphenol (NP, 100% detection rate) and octylphenol (OP, 100% detection rate) might also be responsible for the estrogenic activities in water sources. Potential health risk induced by the estrogenic chemicals in source water may be posed to the residents through water drinking.     

Investigations into a novel method for atmospheric polycyclic aromatic hydrocarbon monitoring

A novel analytical method for atmospheric polycyclic aromatic hydrocarbons (PAHs) was developed based on laser induced fluorescence (LIF) of samples on quartz multi-channel polydimethylsiloxane traps. A tunable dye laser with a frequency doubling crystal provided the excitation radiation, and a double monochromator with a photomultiplier tube detected emitted fluorescence. The method allowed for the rapid (<5 min), cost effective analysis of samples. Those yielding interesting results could be further analysed by direct thermal desorption-gas chromatography–mass spectrometry (TD–GC–MS, with limits of detection of ～0.3 ng m^?3), as photodegradation was minimal (<10% over 5 min irradiation). Small amounts of naphthalene photodegradation products identified by TD–GC–MS after >15 min irradiation, included phenol, benzyl alcohol and phthalic anhydride. Without any signal optimization, a LIF detection limit of ～1 μg m^?3 was established for naphthalene using a diffusion tube (diffusion rate of 2 ng s^?1) and 292 nm excitation.     

Acute toxicity of 353-nonylphenol and its metabolites for zebrafish embryos

Background, aim and scope  Nonylphenol (NP) can be detected in the aquatic environment all over the world. It is applied as a technical mixture of isomers of which 353-NP is the most relevant both in terms of abundance (about 20% of total mass) and endocrine potential. 353-NP is metabolised in sewage sludge. The aims of the present study were to determine and to compare the acute toxicity of t-NP, 353-NP and its metabolites as well as to discuss if the toxicity of 353-NP changes during degradation. Materials and methods  353-NP and two of its metabolites were synthesised. The zebrafish embryo test was performed according to standard protocols. Several lethal and non-lethal endpoints during embryonal development were reported. NOEL, LOEL and EC₅₀ were calculated. Results  All tested compounds caused lethal as well as non-lethal malformations during embryo development. 353-NP showed a higher toxicity (EC₅₀ for lethal endpoints 6.7 mg/L) compared to its metabolites 4-(3.5-dimethyl-3-heptyl)-2-nitrophenol (EC₅₀ 13.3 mg/L) and 4-(3,5-dimethyl-3-heptyl)-2-bromophenol (EC₅₀ 27.1 mg/L). Discussion  In surface water, concentrations of NP are far below the NOEC identified by the zebrafish embryo test. However, in soils and sewage sludge, concentrations may reach or even exceed these concentrations. Therefore, sludge-treated sites close to surface waters should be analysed for NP and its metabolites in order to detect an unduly high contamination due to runoff events. Conclusions  The results of the present study point out that the toxicity of 353-NP probably declines during metabolisation in water, sediment and soil, but does not vanish since the major metabolites exhibit a clear toxic potential for zebrafish embryos. Recommendations and perspectives  Metabolites of environmental pollutants should be included in the ecotoxicological test strategy for a proper risk assessment. An erratum to this article can be found at     

Cloud chemistry in the eastern United States, as sampled from three high-elevation sites along the Appalachian Mountains

Atmospheric deposition of acidic cloud water is thought to be one of the causes for the recent forest decline in industrialized areas of the world. The present paper presents results from the Mountain Acid Deposition Program (MADPro), a part of EPA's Clean Air Status and Trends Network, (CASTnet). We used automated cloud water collectors at three selected mountain sites (Whiteface Mt., NY; Whitetop Mt., VA; and Clingman's Dome, TN) to take hourly samples from non-precipitating clouds during temperate (non- freezing) seasons of each year from 1994 to 1997. Samples were promptly analyzed for pH, conductivity, and concentration of dissolved ions. Cloud liquid water content (LWC) and meteorological parameters were measured at each site. Mean cloud frequencies and LWC of clouds were higher at Whiteface Mt., NY, than in the Southern Appalachians. The four most prevalent ions found in cloud water samples were usually, in order of decreasing concentration: sulfate (SO²⁻₄) hydrogen (H⁺), ammonium (NH₄⁺), and nitrate (NO₃⁻). Within cloud events the concentration of these major ions tended to co-vary. Typically there was an inverse relationship between LWC of the cloud and ionic concentration of the cloud water. During the sampling season, the highest ionic concentrations were seen during mid-summer. Ionic concentrations of samples from the southern sites were significantly higher than samples from Whiteface Mt., but further analysis indicates that this is at least partially due to the north–south difference in the LWC of clouds. MADPro results are shown to be comparable with previous studies of cloud chemistry in North America.     

Modelling concentrations of decamethylcyclopentasiloxane in two UK rivers using LF2000-WQX

Current regulatory environmental exposure assessments for decamethylcyclopentasiloxane (D₅), used in a range of personal care products, are based on a number of erroneous assumptions. Using an estimated D₅ flux to waste water of 11.6 mg cap⁻¹ d⁻¹, a 95.2% removal rate in Sewage Treatment Plants (STP) and a dilution factor of 10 results in modelled surface water concentrations that are up to an order of magnitude higher than concentrations observed downstream of STPs in two UK rivers. A GIS-based water quality model (LF2000-WQX) was used to predict concentrations of D₅ in two UK rivers. Assuming the STP removal rate is reasonable, a waste water flux of 2.4 mg cap⁻¹ d⁻¹ is needed in order to obtain a reasonable match between predicted and observed in-river concentrations. This flux is consistent with measured effluent concentrations. The results highlight major uncertainties in estimating chemical emission rates for volatile chemicals used in personal care products and suggest that measured concentrations in waste water are needed to refine exposure assessments.     

Solubilities of trace copper and lead species and the complexing capacity of river water in the Linggi River Basin

Chemical forms of copper and lead in river water of the Linggi River Basin have been fractionated into ASV labile, moderately labile, slowly labile, and inert metal species, based on a previously proposed scheme. Free (hydrated) metal ions were identified by a potentiometric method using an ion selective electrode. Speciation results showed that the soluble copper and lead species occurred mainly in the moderately labile and slowly labile fractions. The speciation results are primarily interpreted in terms of organic interaction due to agricultural based and light industries, and urban discharges. The measured metal complexing capacity (MCC) of the samples reveals consistency of the results with the nature of the discharge. MCC correlates reasonably well with the value from the permanganate test on the river water. In general, the speciation pattern was found to be consistent with the findings of other workers.     

Dissolved organic carbon in rainwater: Glassware decontamination and sample preservation and volatile organic carbon

The efficiency of different methods for the decontamination of glassware used for the analysis of dissolved organic carbon (DOC) was tested using reported procedures as well as new ones proposed in this work. A Fenton solution bath (1.0 mmol L⁻¹ Fe²⁺ and 100 mmol L⁻¹ H₂O₂) for 1 h or for 30 min employing UV irradiation showed to combine simplicity, low cost and high efficiency. Using the optimized cleaning procedure, the DOC for stored UV-irradiated ultra-pure water reached concentrations below the limit of detection (0.19 μmol C L⁻¹). Filtered (0.7 μm) rain samples maintained the DOC integrity for at least 7 days when stored at 4 °C. The volatile organic carbon (VOC) fraction in the rain samples collected at two sites in São Paulo state (Brazil) ranged from 0% to 56% of their total DOC content. Although these high-VOC concentrations may be derived from the large use of ethanol fuel in Brazil, our results showed that when using the high-temperature catalytic oxidation technique, it is essential to measure DOC rather than non-purgeble organic carbon to estimate organic carbon, since rainwater composition can be quite variable, both geographically and temporally.     

Polycyclic aromatic hydrocarbons in air on small spatial and temporal scales – II. Mass size distributions and gas-particle partitioning

Polycyclic aromatic hydrocarbons (PAHs) were measured together with inorganic air pollutants at two urban sites and one rural background site in the Banja Luka area, Bosnia and Hercegovina, during 72 h in July 2008 using a high time resolution (5 samples per day) with the aim to study gas-particle partitioning, aerosol mass size distributions and to explore the potential of a higher time resolution (4 h-sampling).In the particulate phase the mass median diameters of the PAHs were found almost exclusively in the accumulation mode (0.1–1.0 μm of size). These were larger for semivolatile PAHs than for non-volatile PAHs. Gas-particle partitioning of semivolatile PAHs was strongly influenced by temperature. The results suggest that the Junge–Pankow model is inadequate to explain the inter-species variation and another process must be significant for phase partitioning which is less temperature sensitive than adsorption. Care should be taken when interpreting slopes m of plots of the type log K_p = m log p_L⁰ + b based on 24 h means, as these are found sensitive to the time averaging, i.e. tend to be higher than when based on 12 h-mean samples.     

Removal of Pb2+ from aqueous solution by adsorption on chemically modified muskmelon peel

A cost-effective biosorbent was prepared by a green chemical modification process from muskmelon peel by saponification with alkaline solution of Ca(OH)₂. Its adsorption behavior for lead ions was investigated and found to exhibit excellent adsorption properties. Results showed that the optimal equilibrium pH range for 100 % adsorption is from 4 up to 6.4. Adsorption equilibrium was attained within 10 min. The adsorption process can be described well by Langmuir model and pseudo-second-order kinetics equation, respectively. The maximum adsorption capacity for lead ions was found to be 0.81 mol/kg. Pectic acid contained in the muskmelon peel is the main factor responsible for the uptake of lead ions onto the gel, and the chemical modification process presented in this study can be assumed effective to prepare other similar biomaterials. The large adsorption capacity and the fast adsorption rate indicated that chemically saponified muskmelon peel gel in present study has great potential to be used as a cost-effective adsorbent for the removal of lead ions from the water.     

A simple spectroscopic method to determine dimethoate in water samples by complex formation

Abstract

A simple and rapid method for the determination of dimethoate in water was developed based on the monitoring of the complex formation between bis 5-phenyldipyrrinate of nickel (II) and the herbicide dimethoate. The method showed a short response time (10?s), high selectivity (very low interference from other sulfate and salts), high sensitivity (limit of detection (LOD) 0.45?µM, limit of quantitation (LOQ) of 1.39?µM), and a K_d of 2.4?µM. Stoichiometry experiments showed that complex formation occurred with a 1:1 relation. The method was applied to different environmental water samples such as lagoon, stream, urban, and groundwater samples. The results indicated that independently from the water source, the method exhibited high precision (0.25–2.47% variation coefficient) and accuracy (84.42–115.68% recovery). In addition, the method was also tested using an effluent from a wastewater treatment plant from Mexico; however, the results indicated that the presence of organic matter had a pronounced effect on the detection.