Greenhouse gases accounting and reporting for waste management – A South African perspective

This paper investigates how greenhouse gases are accounted and reported in the waste sector in South Africa. Developing countries (including South Africa) do not have binding emission reduction targets, but many of them publish different greenhouse gas emissions data which have been accounted and reported in different ways. Results show that for South Africa, inventories at national and municipal level are the most important tools in the process of accounting and reporting greenhouse gases from waste. For the development of these inventories international initiatives were important catalysts at national and municipal levels, and assisted in developing local expertise, resulting in increased output quality. However, discrepancies in the methodology used to account greenhouse gases from waste between inventories still remain a concern. This is a challenging issue for developing countries, especially African ones, since higher accuracy methods are more data intensive. Analysis of the South African inventories shows that results from the recent inventories can not be compared with older ones due to the use of different accounting methodologies. More recently the use of Clean Development Mechanism (CDM) procedures in Africa, geared towards direct measurements of greenhouse gases from landfill sites, has increased and resulted in an improvement of the quality of greenhouse gas inventories at municipal level.     

Municipal solid waste management in Kolkata,India – A review

Kolkata is one of four metropolitan cities in India. With an area of 187.33 sq km and a population of about 8 million, it generates around 3,000 t d^?1 of municipal solid waste (MSW) at a rate of 450–500 g per capita per day. With rapid urbanization as a result of planned and unplanned growth and industrialization, the problems associated with handling MSW have increased at an alarming rate over the past few years. No source segregation arrangement exists; there is only limited (60%) house-to-house collection; and 50–55% open vats are used in the present collection system. The operational efficiency of the Kolkata Municipal Corporation (KMC) transport system is about 50%, with a fleet composed of about 30–35% old vehicles. The majority (80%) of these, particularly the hired vehicles, are more than 20 years old. The newly added areas covered by KMC have even lower collection efficiencies, and only an informal recycling system exists. The waste collected has a low energy value (3,350–4,200 kJ kg^?1) with high moisture and inert content. A 700 t d^?1 compost plant set up in 2000 has not been functioning effectively since 2003. Open dumping (without liners and without a leachate management facility) and the threat of groundwater pollution, as well as saturation of an existing landfill site (Dhapa) are the most pressing problems for the city today. KMC spends 70–75% of its total expenditures on collection of solid waste, 25–30% on transportation, and less than 5% on final disposal arrangements. The Kolkata Environmental Improvement Project, funded by the Asian Development Bank, is seen as only a partial solution to the problem. A detailed plan should emphasize segregation at the source, investment in disposal arrangements (including the use of liners and leachate collection), and an optimized transport arrangement, among improvements.     

Household hazardous waste quantification,characterization and management in China’s cities: A case study of Suzhou

A four-stage systematic tracking survey of 240 households was conducted from the summer of 2011 to the spring of 2012 in a Chinese city of Suzhou to determine the characteristics of household hazardous waste (HHW) generated by the city. Factor analysis and a regression model were used to study the major driving forces of HHW generation. The results indicate that the rate of HHW generation was 6.16 (0.16–31.74, 95% CI) g/person/day, which accounted for 2.23% of the household solid waste stream. The major waste categories contributing to total HHW were home cleaning products (21.33%), medicines (17.67%) and personal care products (15.19%). Packaging and containers (one-way) and products (single-use) accounted for over 80% of total HHW generation, implying a considerable potential to mitigate HHW generation by changing the packaging design and materials used by manufacturing enterprises. Strong correlations were observed between HHW generation (g/person/day) and the driving forces group of “household structure” and “consumer preferences” (among which the educational level of the household financial manager has the greatest impact). Furthermore, the HHW generation stream in Suzhou suggested the influence of another set of variables, such as local customs and culture, consumption patterns, and urban residential life-style. This study emphasizes that HHW should be categorized at its source (residential households) as an important step toward controlling the HHW hazards of Chinese cities.     

Risk management for outsourcing biomedical waste disposal – Using the failure mode and effects analysis

Using the failure mode and effects analysis, this study examined biomedical waste companies through risk assessment. Moreover, it evaluated the supervisors of biomedical waste units in hospitals, and factors relating to the outsourcing risk assessment of biomedical waste in hospitals by referring to waste disposal acts. An expert questionnaire survey was conducted on the personnel involved in waste disposal units in hospitals, in order to identify important factors relating to the outsourcing risk of biomedical waste in hospitals. This study calculated the risk priority number (RPN) and selected items with an RPN value higher than 80 for improvement. These items included “availability of freezing devices”, “availability of containers for sharp items”, “disposal frequency”, “disposal volume”, “disposal method”, “vehicles meeting the regulations”, and “declaration of three lists”. This study also aimed to identify important selection factors of biomedical waste disposal companies by hospitals in terms of risk. These findings can serve as references for hospitals in the selection of outsourcing companies for biomedical waste disposal.     

DISCRISET: A battery of tests for fast waste classification – Application of tests on waste extracts

The Hazardous Waste Directive (HWD, Council Directive 91/689/EC, 1991) provides a framework for classification of hazardous waste, based on 15 Hazard (H)-criteria. For complex wastes the HWD foresees the application of toxicity tests on the waste material itself to assess its toxic properties. However, these proposed test methods often involve mammalian testing, which is not acceptable from an ethical point of view, nor is it feasible economically. The DISCRISET project was initiated to investigate the use of alternative chemical and biological fast screening tests for waste hazard classification. In the first part of the project, different methods were reviewed and a testing strategy was proposed to minimize time and cost of analysis by a tiered approach. This includes as a first tier chemical analysis followed by a general acute toxicity screen as a second tier and as a third tier mechanistic toxicity tests to assess chronic toxicity (genotoxicity, hormone disturbance, teratogenic effects, immunologic activity). In this phase of the project, selected methods were applied to 16 different waste samples from various sources and industries. The first tier chemical tests are recommended for the full characterization of the leachate fraction (inorganics) but not for the organic fraction of samples. Here the chemical characterization is only useful if toxic content is known or suspected. As second tier the fast bacterial test Microtox is validated as a general toxicity screen for the organic fraction (worst case organic extract). Samples that are not classified in tier 1 or 2 are then further investigated in the third tier by the mechanistic toxicity tests and tested for their potential chronic toxicity: immune activity (TNF-α upregulation) is indicative for corrosive, irritating or sensitising effects (H4/H8/H15), reproductive effects (H10) are indicated by hormone disturbance and early life stage abnormalities in fish larvae when exposed to the extracts and mutagenicity and carcinogenicity (H7, H11) are indicated by SOS response induction and increased mutation frequency in the Ames test when exposed to the extracts. Results indicate that the combination of chemical tests and bioassays allows important hazardous properties to be addressed and the tiered approach ensures that the tests are performed quickly and economically. The suggested strategy provides a solid and ethical alternative to the methods described in the HWD and is a vast improvement on the current, arbitrary classification.     

Global Environment Facility’s support for sustainable waste management

From the global perspective, the issue of waste management is becoming increasingly important. Given the increasing amount and diversifying content of waste, countries should seek out sustainable waste management options, which protect both local and global environments. The Global Environment Facility (GEF), a public financial institution, has supported sustainable waste management in developing countries in achieving global environmental benefits. The GEF’s support for sustainable waste management, from its pilot phase to the end of the fifth replenishment period, has amounted to 118 projects across the globe. Harmful chemicals, such as polychlorinated biphenyls (PCBs), and “waste to energy” initiatives have been the main focuses of the GEF’s support. The GEF’s investment in sustainable waste management has increased in recent years, partly due to the fact that countries are required to manage Persistent Organic Pollutant (POP) wastes in an environmentally safe manner in compliance with the Stockholm Convention on POPs. The GEF is poised to enhance its support for sustainable waste management in the future by mobilizing other financing, integrating multiple focal areas, expanding viewpoints to sustainable cities, and reinforcing its results-based management.     

Clean development mechanism: an incentive for waste management projects?

The Clean Development Mechanism (CDM) was introduced by the Kyoto Protocol to provide a financial incentive to establish project activities in developing countries for reducing greenhouse gas emissions while also fostering sustainable development. This article shows that waste management project activities play an important role in achieving the aims of the CDM. It describes how these activities have to prove additionality, how the emission reductions must be calculated and monitored in order to be eligible and in order to lead to Certified Emission Reductions (CERs). The article further provides an analysis about the various challenges that are involved in applying the CDM scheme to waste management project activities, which require a new specific set of technical skills and regulatory standards.     

Japan’s waste management policies for dioxins and polychlorinated biphenyls

We summarize the measures taken by the Japanese government to prevent the emission of dioxins and polychlorinated biphenyls (PCBs) into the environment. Because incineration is the main method of waste management in Japan, reducing the amount of dioxins emitted from waste incinerators is an essential aspect of proper waste treatment. Intensive measures to prevent the formation of dioxins at the source have been implemented, with a focus on waste treatment methods and improving comprehensive management. The efforts have been very successful, with a 95% reduction in the amount of dioxins emitted between 1997 and 2003. The toxicity of PCBs has been monitored with keen interest since the Yusho incident. Unfortunately, treatment facilities for PCB wastes were not built until long after PCBs had been removed from use, and PCB wastes remained in storage in an untreated state. The Japanese government has promoted the construction of facilities for treating PCB wastes, and five such facilities have commenced operations. To more completely eradicate dioxins, a future challenge will be to reduce the amount of PCB-derived dioxins, which are persistent in the environment and have a long exposure pathway from the environment media to the organism and the human body.     

Review of LCA studies of solid waste management systems – Part II: Methodological guidance for a better practice

Life cycle assessment (LCA) is increasingly used in waste management to identify strategies that prevent or minimise negative impacts on ecosystems, human health or natural resources. However, the quality of the provided support to decision- and policy-makers is strongly dependent on a proper conduct of the LCA. How has LCA been applied until now? Are there any inconsistencies in the past practice? To answer these questions, we draw on a critical review of 222 published LCA studies of solid waste management systems. We analyse the past practice against the ISO standard requirements and the ILCD Handbook guidelines for each major step within the goal definition, scope definition, inventory analysis, impact assessment, and interpretation phases of the methodology. Results show that malpractices exist in several aspects of the LCA with large differences across studies. Examples are a frequent neglect of the goal definition, a frequent lack of transparency and precision in the definition of the scope of the study, e.g. an unclear delimitation of the system boundaries, a truncated impact coverage, difficulties in capturing influential local specificities such as representative waste compositions into the inventory, and a frequent lack of essential sensitivity and uncertainty analyses. Many of these aspects are important for the reliability of the results. For each of them, we therefore provide detailed recommendations to practitioners of waste management LCAs.     

Energy or compost from green waste? – A CO2 – Based assessment

Green waste is increasingly extracted from the material recycling chain and, as a result of the financial subsidy arising from the German renewable energy law for the generation of energy from renewable raw materials; it is fed into the energy recovery process in biomass power stations. A reduction in climate relevant gases is also linked to the material recovery of green waste – in particular when using composts gained from the process as a new raw material in different types of potting compost and plant culture media as a replacement for peat. Unlike energy recovery, material valorisation is not currently subsidised. Through the analysis of material and energy valorisation methods for green waste, with particular emphasis on primary resource consumption and CO₂-balance, it could be determined that the use of green waste for energy generation and its recovery for material and peat replacement purposes can be considered to be on a par. Based on energy recovery or material oriented scenarios, it can be further deduced that no method on its own will achieve the desired outcome and that a combination of recycling processes is more likely to lead to a significant decrease of greenhouse gas emissions.     

Barriers for implementation of “waste to energy” in developing and transition countries: a case study of Serbia

The aim of this study is to assess boundaries and potential for implementation of waste-to-energy projects in developing and transition countries in order to give realistic future directions for waste-to-energy initiatives. For this purpose, Serbia is taken as an example. In order to highlight the most important issues, which hinder the feasibility of waste-to-energy projects, analysis of the status quo of Serbian municipal solid waste management is performed. In addition, based on the current political and social status of the country, the most important factors that need to be solved as a precondition to waste-to-energy projects are defined. This analysis revealed that aside from technical factors, sociopolitical and cultural obstacles must be eliminated as a prerequisite for successful implementation of waste-to-energy projects. We define the most sustainable pathway for waste-to-energy initiatives in Serbia as well as other similar developing and transition countries, which can complement development of the entire waste management system.     

Review of comparative LCAs of food waste management systems – Current status and potential improvements

Twenty-five comparative cycle assessments (LCAs) addressing food waste treatment were reviewed, including the treatment alternatives landfill, thermal treatment, compost (small and large scale) and anaerobic digestion. The global warming potential related to these treatment alternatives varies largely amongst the studies. Large differences in relation to setting of system boundaries, methodological choices and variations in used input data were seen between the studies. Also, a number of internal contradictions were identified, many times resulting in biased comparisons between alternatives. Thus, noticed differences in global warming potential are not found to be a result of actual differences in the environmental impacts from studied systems, but rather to differences in the performance of the study. A number of key issues with high impact on the overall global warming potential from different treatment alternatives for food waste were identified through the use of one-way sensitivity analyses in relation to a previously performed LCA of food waste management. Assumptions related to characteristics in treated waste, losses and emissions of carbon, nutrients and other compounds during the collection, storage and pretreatment, potential energy recovery through combustion, emissions from composting, emissions from storage and land use of bio-fertilizers and chemical fertilizers and eco-profiles of substituted goods were all identified as highly relevant for the outcomes of this type of comparisons. As the use of LCA in this area is likely to increase in coming years, it is highly relevant to establish more detailed guidelines within this field in order to increase both the general quality in assessments as well as the potentials for cross-study comparisons.     

The impact of Local Authorities’ interventions on household waste collection: A case study approach using time series modelling

At a local Government level there have been many interventions and changes made to household waste collection services to meet new regulatory requirements. These changes include separate collection of recyclable and organic materials. This paper has used a time series model to quantify the success of interventions introduced by a LA.The case study was a medium sized UK LA, Charnwood Borough Council (CBC), the research analyses monthly data of quantities of recyclates, garden waste for composting and residual waste for landfill disposal. The time series model was validated with a five year data set and used to measure the impacts of the various changes to identify which intervention was the most successful, while controlling for season and number of working days. The results show the interventions analysed both had abrupt and permanent positive impacts on the yield of recyclable materials, and a corresponding negative impact on the residual waste.The model could be added to the National data base to help LAs to compare interventions and to understand which schemes encourage householder participation and improve recycling performance.     

Financial sustainability in municipal solid waste management – Costs and revenues in Bahir Dar,Ethiopia

Providing good solid waste management (SWM) services while also ensuring financial sustainability of the system continues to be a major challenge in cities of developing countries. Bahir Dar in northwestern Ethiopia outsourced municipal waste services to a private waste company in 2008. While this institutional change has led to substantial improvement in the cleanliness of the city, its financial sustainability remains unclear. Is the private company able to generate sufficient revenues from their activities to offset the costs and generate some profit?This paper presents a cost-revenue analysis, based on data from July 2009 to June 2011. The analysis reveals that overall costs in Bahir Dar’s SWM system increased significantly during this period, mainly due to rising costs related to waste transportation. On the other hand, there is only one major revenue stream in place: the waste collection fee from households, commercial enterprises and institutions. As the efficiency of fee collection from households is only around 50%, the total amount of revenues are not sufficient to cover the running costs. This results in a substantial yearly deficit. The results of the research therefore show that a more detailed cost structure and cost-revenue analysis of this waste management service is important with appropriate measures, either by the privates sector itself or with the support of the local authorities, in order to enhance cost efficiency and balance the cost-revenues towards cost recovery. Delays in mitigating the evident financial deficit could else endanger the public-private partnership (PPP) and lead to failure of this setup in the medium to long term, thus also endangering the now existing improved and currently reliable service.We present four options on how financial sustainability of the SWM system in Bahir Dar might be enhanced: (i) improved fee collection efficiency by linking the fees of solid waste collection to water supply; (ii) increasing the value chain by sales of organic waste recycling products; (iii) diversifying revenue streams and financing mechanisms (polluter-pays-, cross-subsidy- and business-principles); and (iv) cost reduction and improved cost-effectiveness.We argue that in a PPP setup such as in Bahir Dar, a strong alliance between the municipality and private enterprise is important so that appropriate solutions for improved financial sustainability of a SWM system can be sought and implemented.     

Screening tests for hazard classification of complex waste materials – Selection of methods

In this study we describe the development of an alternative methodology for hazard characterization of waste materials. Such an alternative methodology for hazard assessment of complex waste materials is urgently needed, because the lack of a validated instrument leads to arbitrary hazard classification of such complex waste materials. False classification can lead to human and environmental health risks and also has important financial consequences for the waste owner. The Hazardous Waste Directive (HWD) describes the methodology for hazard classification of waste materials. For mirror entries the HWD classification is based upon the hazardous properties (H1–15) of the waste which can be assessed from the hazardous properties of individual identified waste compounds or – if not all compounds are identified – from test results of hazard assessment tests performed on the waste material itself. For the latter the HWD recommends toxicity tests that were initially designed for risk assessment of chemicals in consumer products (pharmaceuticals, cosmetics, biocides, food, etc.). These tests (often using mammals) are not designed nor suitable for the hazard characterization of waste materials. With the present study we want to contribute to the development of an alternative and transparent test strategy for hazard assessment of complex wastes that is in line with the HWD principles for waste classification. It is necessary to cope with this important shortcoming in hazardous waste classification and to demonstrate that alternative methods are available that can be used for hazard assessment of waste materials. Next, by describing the pros and cons of the available methods, and by identifying the needs for additional or further development of test methods, we hope to stimulate research efforts and development in this direction. In this paper we describe promising techniques and argument on the test selection for the pilot study that we have performed on different types of waste materials. Test results are presented in a second paper.As the application of many of the proposed test methods is new in the field of waste management, the principles of the tests are described. The selected tests tackle important hazardous properties but refinement of the test battery is needed to fulfil the a priori conditions.     

Solid health care waste management status at health care centers in the West Bank – Palestinian Territory

Health care waste is considered a major public health hazard. The objective of this study was to assess health care waste management (HCWM) practices currently employed at health care centers (HCCs) in the West Bank – Palestinian Territory. Survey data on solid health care waste (SHCW) were analyzed for generated quantities, collection, separation, treatment, transportation, and final disposal. Estimated 4720.7 m³ (288.1 tons) of SHCW are generated monthly by the HCCs in the West Bank. This study concluded that: (i) current HCWM practices do not meet HCWM standards recommended by the World Health Organization (WHO) or adapted by developed countries, and (ii) immediate attention should be directed towards improvement of HCWM facilities and development of effective legislation. To improve the HCWM in the West Bank, a national policy should be implemented, comprising a comprehensive plan of action and providing environmentally sound and reliable technological measures.     

Review of LCA studies of solid waste management systems – Part I: Lessons learned and perspectives

The continuously increasing solid waste generation worldwide calls for management strategies that integrate concerns for environmental sustainability. By quantifying environmental impacts of systems, life cycle assessment (LCA) is a tool, which can contribute to answer that call. But how, where and to which extent has it been applied to solid waste management systems (SWMSs) until now, and which lessons can be learnt from the findings of these LCA applications? To address these questions, we performed a critical review of 222 published LCA studies of SWMS. We first analysed the geographic distribution and found that the published studies have primarily been concentrated in Europe with little application in developing countries. In terms of technological coverage, they have largely overlooked application of LCA to waste prevention activities and to relevant waste types apart from household waste, e.g. construction and demolition waste. Waste management practitioners are thus encouraged to abridge these gaps in future applications of LCA. In addition to this contextual analysis, we also evaluated the findings of selected studies of good quality and found that there is little agreement in the conclusions among them. The strong dependence of each SWMS on local conditions, such as waste composition or energy system, prevents a meaningful generalisation of the LCA results as we find it in the waste hierarchy. We therefore recommend stakeholders in solid waste management to regard LCA as a tool, which, by its ability of capturing the local specific conditions in the modelling of environmental impacts and benefits of a SWMS, allows identifying critical problems and proposing improvement options adapted to the local specificities.