Use of thermal desorption–gas chromatography–mass spectrometry (TD–GC–MS) on identification of odorant emission focus by volatile organic compounds characterisation

Volatile organic compounds (VOCs) from several different municipal solid wastes’ treatment plants in Mallorca (Spain) have been analysed by thermal desorption–gas chromatography–mass spectrometry (TD–GC–MS). Ambient (immission) air was collected during February and March 2011 by active sampling onto sorbents Tenax™ TA and Carboxen™ 1000. The study presents the chemical characterisation of 93 volatile organic compounds (VOCs) from an overall set of 84 immission air samples. 70 VOCs were positively identified.The linear fit for all 93 external standard calibration, from 10 mg L⁻¹ to 150 mg L⁻¹ (n = 4), was within the range 0.974 < r² < 0.998. Limits of detection of the method (LOD) for all the standards were within the range 1.1–4,213 pg, as the absolute standard amount spiked into sorbent tubes in 1 μL standard mixture (dissolved in methanol).Overall results stated systematic correlation between waste’s nature and VOCs’ air composition. Organic wastes show main contribution of terpenes, waste water sludge residues’ of reduced sulphured compounds (RSCs) and municipal solid wastes show contribution of a wide sort of VOCs. The use of a chemometric approach for variable’s reduction to 12 principal components enables evaluation of similarities and dissimilarities between facilities. PCA clearly related samples to its corresponding facility on the basis of their VOCs composition and the ambient temperature.     

Fenton-like oxidation and mineralization of phenol using synthetic Fe(II)–Fe(III) green rusts

Background, aim, and scope  

In literature, the environmental applications of green rust (GR) have mainly been pointed out through the reduction of inorganic contaminants and the reductive dechlorination of chlorinated organics. However, reactions involving GR for the oxidation and mineralization of organic pollutants remain very scantly described. In this study, the ability of three synthetic Fe(II)–Fe(III) green rusts, GR(CO₃²⁻), GR(SO₄²⁻), and GR(Cl⁻), to promote Fenton-like reaction was examined by employing phenol as a model pollutant. Unlike the traditional Fenton’s reagent (dissolved Fe(II) + H₂O₂), where the pH values have to be lowered to less than 4, the proposed reaction can effectively oxidize the organic molecules at neutral pH and could avoid the initial acidification which may be costly and destructive for the in situ remediation of contaminated groundwater and soils. The green rust reactivity towards the oxidative transformation of phenol was thoroughly evaluated by performing a large kinetic study, chemical analyses, and spectroscopic investigations.     

The climatology of summertime O3 and SO2 (1977–1981)

The mean monthly distribution of the diurnal maximum O₃ and of the SO₂ in the eastern two-thirds of the U.S. was determined for the summer (July and August) of 1977–1981. Highest O₃ concentrations varied from 60 to 90 ppbv and covered an area of about 2 to 5 × 10⁶ km²; and that for SO₂ varied from values greater than 10 ppbv to values about 25 ppbv and covered an area of 0.3–1.3 × 10⁶ km². The geographical locations of the centers of high O₃ concentrations were related to the path of the anticyclones. The centers of high SO₂ concentration were affected by the path of anticyclones but to a lesser extent. The SO₂ distribution was controlled to a significant extent by the location of major SO₂ sources. The data suggested that highpressure systems that become stationary, weaken and dissipate in the eastern two-thirds of the U.S. have a profound effect on the O₃ and SO₂ distribution.     

Implications of Rural–Urban Migration for Conservation of the Atlantic Forest and Urban Growth in Misiones,Argentina (1970–2030)

Global trends of increasing rural–urban migration and population urbanization could provide opportunities for nature conservation, particularly in regions where deforestation is driven by subsistence agriculture. We analyzed the role of rural population as a driver of deforestation and its contribution to urban population growth from 1970 to the present in the Atlantic Forest of Argentina, a global conservation priority. We created future land-use-cover scenarios based on human demographic parameters and the relationship between rural population and land-cover change between 1970 and 2006. In 2006, native forest covered 50% of the province, but by 2030 all scenarios predicted a decrease that ranged from 18 to 39% forest cover. Between 1970 and 2001, rural migrants represented 20% of urban population growth and are expected to represent less than 10% by 2030. This modeling approach shows how rural–urban migration and land-use planning can favor nature conservation with little impact on urban areas.     

Determination of indicator polychlorinated biphenyls (PCBs) by gas chromatography–electron capture detector

An effective method for determination of indicator polychlorinated biphenyls (PCBs) has been validated using gas chromatography (GC) equipped with electron capture detector (ECD). The GC–ECD method was validated by determining the linear range (working range) for determination of the compounds, minimum detectable quantities (MDQ), the precision and accuracy of the method for the analysis of the compounds. MDQ obtained for the compounds ranges from 0.0005 to 0.002 ng. Indeed the method was found to be more sensitive as the number of chlorine atoms attached to the biphenyl increases. The precision and accuracy of the GC method validated ranges from 2.4% to 14.5% and −7.0% to 14.6% respectively. Coefficient of variation associated with the repeatability of the retention times and corresponding peak areas was found to be 0.0001–0.0007 for the retention times and 0.0014–0.059 for the peak areas. Percentage recoveries for the compounds were in the range of 95.7–101.0%. The validated method was then applied to determine levels of indicator PCBs in sediments sampled from eleven sampling points along the Lake Bosuntwi in Ghana and the highest PCB load of 19.17 ng g⁻¹ was recorded at Pipie No. 2. PCB 52 and PCB 101 were found to be the most ubiquitous indicator PCBs in the study area, both with 90.91% occurrence.     

Bibliometric analysis of the research landscape on rice husks gasification (1995–2019)

Environmental Science and Pollution Research - The processing of rice (Oryza sativa L.) generates large quantities of lignocellulosic wastes termed rice husks (RH). Numerous researchers have...     

Hans-Joachim Schallna? (1957–2007)

Ohne Zusammenfassung     

Characterization of extracellular polymeric substances (EPS) from periphyton using liquid chromatography-organic carbon detection–organic nitrogen detection (LC-OCD-OND)

A protocol was developed to extract, fractionate, and quantitatively analyze periphyton extracellular polymeric substances (EPS), which obtains both information on the molecular weight (M _r) distribution and protein and polysaccharide content. The EPS were extracted from freshwater periphyton between July and December 2011. Organic carbon (OC) compounds from different EPS extracts were analyzed using liquid chromatography-organic carbon detection–organic nitrogen detection (LC-OCD-OND), and total protein and polysaccharide content were quantified. Four distinct OC fractions, on the basis of M _r, were identified in all extracts, corresponding to high M _r biopolymers (≥80–4 kDa), degradation products of humic substances (M _r not available), low M _r acids (10–0.7 kDa), and small amphiphilic/neutral compounds (3–0.5 kDa). Low C/N ratios (4.3?±?0.8) were calculated for the biopolymer fractions, which represented 16–38 % of the measured dissolved organic carbon (DOC), indicating a significant presence of high M _r proteins in the EPS. Protein and polysaccharide represented the two major components of EPS and, when combined, accounted for the measured DOC in extracts. Differences in specific OC fractions of EPS extracts over the course of the study could be quantified using this method. This study suggests that LC-OCD-OND is a new valuable tool in EPS characterization of periphyton.     

Electron paramagnetic resonance (EPR) investigations of lichens – 1: effects of air pollution

Electron paramagnetic resonance (EPR) investigations were carried out on more than 800 samples of lichens from Lower Silesia, southwest Poland. A statistically confirmed correlation between annual average concentration of sulphur dioxide in the atmosphere and concentration of semiquinone radicals in Hypogymnia physodes thalli was found. Similar results were obtained for Umbilicaria species from the Karkonosze Mountains. Distribution of semiquinone radicals in lichen thalli was also investigated. The action of nitrogen dioxide on Umbilicaria species resulted in the synthesis of iminoxy radicals in the thalli. The intensification of the semiquinone free radical production in lichen thalli from atmospherically polluted environments and the degradation of lichen acids to β-diketone compounds would appear to be parallel processes. The properties of the iminoxyls derived from β-diketones in the lichen matrix (anisotropic spectra at room temperature) and in organic solutions after extraction procedure were also examined by EPR.     

The sea–air exchange of mercury (Hg) in the marine boundary layer of the Augusta basin (southern Italy): Concentrations and evasion flux

The first attempt to systematically investigate the atmospheric mercury (Hg) in the MBL of the Augusta basin (SE Sicily, Italy) has been undertaken. In the past the basin was the receptor for Hg from an intense industrial activity which contaminated the bottom sediments of the Bay, making this area a potential source of pollution for the surrounding Mediterranean. Three oceanographic cruises have been thus performed in the basin during the winter and summer 2011/2012, where we estimated averaged Hg_atm concentrations of about 1.5 ± 0.4 (range 0.9–3.1) and 2.1 ± 0.98 (range 1.1–3.1) ng m⁻³ for the two seasons, respectively. These data are somewhat higher than the background Hg_atm value measured over the land (range 1.1 ± 0.3 ng m⁻³) at downtown Augusta, while are similar to those detected in other polluted regions elsewhere. Hg evasion fluxes estimated at the sea/air interface over the Bay range from 3.6 ± 0.3 (unpolluted site) to 72 ± 0.1 (polluted site of the basin) ng m⁻² h⁻¹. By extending these measurements to the entire area of the Augusta basin (∼23.5 km²), we calculated a total sea–air Hg evasion flux of about 9.7 ± 0.1 g d⁻¹ (∼0.004 t yr⁻¹), accounting for ∼0.0002% of the global Hg oceanic evasion (2000 t yr⁻¹). The new proposed data set offers a unique and original study on the potential outflow of Hg from the sea–air interface at the basin, and it represents an important step for a better comprehension of the processes occurring in the marine biogeochemical cycle of this element.     

Development and Evaluation of a Continuous Coarse (PM10–PM25) Particle Monitor

ABSTRACT

In this paper, we describe the development and laboratory and field evaluation of a continuous coarse (2.5-10 um) particle mass (PM) monitor that can provide reliable measurements of the coarse mass (CM) concentrations in time intervals as short as 5-10 min. The operating principle of the monitor is based on enriching CM concentrations by a factor of ~25 by means of a 2.5-um cut point round nozzle virtual impactor while maintaining fine mass (FM)—that is, the mass of PM_{2 5} at ambient concentrations. The aerosol mixture is subsequently drawn through a standard tapered element oscillating microbalance (TEOM), the response of which is dominated by the contributions of the CM, due to concentration enrichment. Findings from the field study ascertain that a TEOM coupled with a PM₁₀ inlet followed by a 2.5-um cut point round nozzle virtual impactor can be used successfully for continuous CM concentration measurements. The average concentration-enriched CM concentrations measured by the TEOM were 26-27 times higher than those measured by the time-integrated PM₁₀ samplers [the micro-orifice uniform deposit     

Current State of the Altai Glaciers (Russia) and Trends Over the Period of Instrumental Observations 1952–2008

Results of research into climate and glacier dynamics in the Altai Mountains (Russia) over the period of instrumental observations (1952–2008) are presented in this article. About 1030 glaciers with a total area of 805 km² and volume of 42.5 km³ have been recorded in the Altai Region. The average summer air temperature in different regions of the Altai has increased during the study period from about 0.2°C (Aktru) to 1.1°C (Akkem). The annual atmospheric precipitation rate has also increased, by 8–10%. Since 1952, the glacier area in different regions of the Altai has decreased by 9–27%, and volume by 12–24%. By 2008, as a result of degradation, the total number of glaciers was 953 with an area of 724 km² and volume of 38 km³.     

Combined effects of DOM and biosurfactant enhanced biodegradation of polycylic armotic hydrocarbons (PAHs) in soil–water systems

This study systematically investigated the interactive effects of dissolved organic matter (DOM) and biosurfactant (rhamnolipid) on the biodegradation of phenanthrene (PHE) and pyrene (PYR) in soil–water systems. The degradations of two polycyclic aromatic hydrocarbons (PAHs) were fitted well with first order kinetic model and the degradation rates were in proportion to the concentration of biosurfactant. In addition, the degradation enhancement of PHE was higher than that of PYR. The addition of soil DOM itself at an environmental level would inhibit the biodegradation of PAHs. However, in the system with co-existence of DOM and biosurfactant, the degradation of PAHs was higher than that in only biosurfactant addition system, which may be attributed to the formation of DOM–biosurfactant complex micelles. Furthermore, under the combined conditions, the degradation of PAH increased with the biosurfactant concentration, and the soil DOM added system showed slightly higher degradation than the compost DOM added system, indicating that the chemical structure and composition of DOM would also affect the bioavailability of PAHs. The study result may broaden knowledge of biosurfactant enhanced bioremediation of PAHs contaminated soil and groundwater.     

Loss of traditional knowledge aggravates wolf–human conflict in Georgia (Caucasus) in the wake of socio-economic change

Reports of the damage from wolf attacks have increased considerably over the last decade in Georgia (in the Caucasus). We interviewed locals about this problem in two focal regions: the Lanchkhuti area (in western Georgia) and Kazbegi District (in eastern Georgia) where livestock numbers had increased by an order of magnitude owing to dramatic shifts in the local economies over the last decade. This coincided with expanding habitats for wolves (abandoned plantations, for example). We found that the perceived damage from wolves was positively correlated with a poor knowledge of wolf habits and inappropriate livestock husbandry practices. Our results suggest a loss of traditional knowledge contributes strongly to the wolf–human conflicts in Georgia. Restoring traditional, simple but good practices—such as protecting herds using shepherd dogs and introducing bulls into the herds—can help one solve this problem.

Electronic supplementary material

The online version of this article (doi:10.1007/s13280-014-0580-1) contains supplementary material, which is available to authorized users.     

Physical characterization of the fine particle emissions from commercial aircraft engines during the Aircraft Particle Emissions eXperiment (APEX) 1–3

The fine particulate matter (PM) emissions from nine commercial aircraft engine models were determined by plume sampling during the three field campaigns of the Aircraft Particle Emissions Experiment (APEX). Ground-based measurements were made primarily at 30 m behind the engine for PM mass and number concentration, particle size distribution, and total volatile matter using both time-integrated and continuous sampling techniques. The experimental results showed a PM mass emission index (EI) ranging from 10 to 550 mg kg^?1 fuel depending on engine type and test parameters as well as a characteristic U-shaped curve of the mass EI with increasing fuel flow for the turbofan engines tested. Also, the Teflon filter sampling indicated that ～40–80% of the total PM mass on a test-average basis was comprised of volatile matter (sulfur and organics) for most engines sampled. The number EIs, on the other hand, varied from ～10¹⁵ to 10¹⁷ particles kg^?1 fuel with the turbofan engines exhibiting a logarithmic decay with increasing fuel flow. Finally, the particle size distributions of the emissions exhibited a single primary mode that were lognormally distributed with a minor accumulation mode also observed at higher powers for all engines tested. The geometric (number) mean particle diameter ranged from 9.4 to 37 nm and the geometric standard deviation ranged from 1.3 to 2.3 depending on engine type, fuel flow, and test conditions.     

Application of HYDRUS 1D model for assessment of phenol–soil adsorption dynamics

Laboratory-scale batch, vertical, and horizontal column experiments were conducted to investigate the attenuative capacity of a fine-grained clayey soil of local origin in the surrounding of a steel plant wastewater discharge site in West Bengal, India, for removal of phenol. Linear, Langmuir, and Freundlich isotherm plots from batch experimental data revealed that Freundlich isotherm model was reasonably fitted (R ²?=?0.94). The breakthrough column experiments were also carried out with different soil bed heights (5, 10, and 15 cm) under uniform flow to study the hydraulic movements of phenol by evaluating time concentration flow behavior using bromide as a tracer. The horizontal migration test was also conducted in the laboratory using adsorptive phenol and nonreactive bromide tracer to explore the movement of solute in a horizontal distance. The hydrodynamic dispersion coefficients (D) in the vertical and horizontal directions in the soil were estimated using nonlinear least-square parameter optimization method in CXTFIT model. In addition, the equilibrium convection dispersion model in HYDRUS 1D was also examined to simulate the fate and transport of phenol in vertical and horizontal directions using Freundlich isotherm constants and estimated hydrodynamic parameters as input in the model. The model efficacy and validation were examined through statistical parameters such as the coefficient of determination (R ²), root mean square error and design of index (d).     

Development and evaluation of air pollution–linked quality of life (AP-QOL) questionnaire: insight from two different cohorts

Environmental Science and Pollution Research - In this study, the air pollution–related quality of life (AP-QOL) questionnaire was carried out in two geographically and economically different...     

Modeling and optimization of trihalomethanes formation potential of surface water (a drinking water source) using Box–Behnken design

Purpose  

The present research aims to investigate the individual and interactive effects of chlorine dose/dissolved organic carbon ratio, pH, temperature, bromide concentration, and reaction time on trihalomethanes (THMs) formation in surface water (a drinking water source) during disinfection by chlorination in a prototype laboratory-scale simulation and to develop a model for the prediction and optimization of THMs levels in chlorinated water for their effective control.     

Determination of elemental carbon in lake sediments using a thermal–optical transmittance (TOT) method

An improved chemical oxidation pretreatment method has been developed for the determination of elemental carbon (EC) [also known as black carbon (BC) or soot] in lake sediments, using a thermal–optical transmittance (TOT) carbon analyzer. The method employs six steps: (1) removal of carbonates by treatment with HCl; (2) removal of silicates by treatment with HF + HCl; (3) removal of any remaining carbonates by treatment with HCl; (4) removal of humic acids by treatment with NaOH; and (5) oxidation of kerogens by K₂Cr₂O₇ + H₂SO₄. A critical step of zinc chloride treatment was added; this apparently changes EC's morphology and enhances retention on quartz fiber filter, resulting in several-fold increased chemical yield. EC was determined using the TOT method with modified combustion timings. Carbon black (acetylene) and four NIST standard reference materials (SRMs) were used for quality control, and to assess the precision of the analysis. The EC recoveries from 18 carbon black samples varied from 90 to 111%, with a mean value of 99 ± 6%. The high EC recoveries confirmed the validity of the method. Char reference materials (i.e. chestnut wood and grass char) were used to determine potential contribution to EC in our measurements. The char references containing about 700 mg total organic carbon (OC) contributed ～1.5% EC. The measured EC values from four NIST standards were 17.0 ± 0.6, 24.2 ± 3.2, 5.6, and 1.9 ± 0.1 mg g_dw^?1 for SRM-1648, SRM-1649a, SRM-1941b and SRM-8704, respectively. These values in SRMs were in agreement (<±4%) with the previously reported values. The method was applied to determine the EC in sediment cores from an urban lake and a remote mountain lake in the Northeastern United States. The EC concentrations in two lakes mimic the model EC emissions from the industrial revolution in United States.