活性炭处理甲苯气体吸附再生实验研究

研究了活性炭对甲苯废气的吸附穿透过程及热空气解吸过程.穿透曲线实验结果表明,在常规空塔气速范围内,传质区高度基本在5.06～9.75 cm,传质区不饱和度在0.4～0.7.在动态运行情况下,活性炭对甲苯的饱和吸附容量在0.16～0.24 g/g.热空气吹脱实验表明,适宜的脱附工况条件为脱附温度180 ℃、脱附空气流速0.106 m/s、脱附时间40 min.     

Microbial regeneration of spent activated carbon dispersed with organic contaminants: mechanism, efficiency, and kinetic models

Background and purpose

Regeneration of spent activated carbon assumes paramount importance in view of its economic reuse during adsorptive removal of organic contaminants. Classical thermal, chemical, or electrochemical regeneration methods are constrained with several limitations. Microbial regeneration of spent activated carbon provides a synergic combination of adsorption and biodegradation.

Methods

Microorganisms regenerate the surface of activated carbon using sorbed organic substrate as a source of food and energy. Aromatic hydrocarbons, particularly phenols, including their chlorinated derivatives and industrial waste water containing synthetic organic compounds and explosives-contaminated ground water are the major removal targets in adsorption?Cbioregeneration process. Popular mechanisms of bioregeneration include exoenzymatic hypothesis and biodegradation following desorption. Efficiency of bioregeneration can be quantified using direct determination of the substrate content on the adsorbent, the indirect measurement of substrate consumption by measuring the carbon dioxide production and the measurement of oxygen uptake. Modeling of bioregeneration involves the kinetics of adsorption/desorption and microbial growth followed by solute degradation. Some modeling aspects based on various simplifying assumptions for mass transport resistance, microbial kinetics and biofilm thickness, are briefly exposed.

Results

Kinetic parameters from various representative bioregeneration models and their solution procedure are briefly summarized. The models would be useful in predicting the mass transfer driving forces, microbial growth, substrate degradation as well as the extent of bioregeneration.

Conclusions

Intraparticle mass transfer resistance, incomplete regeneration, and microbial fouling are some of the problems needed to be addressed adequately. A detailed techno-economic evaluation is also required to assess the commercial aspects of bioregeneration.     

微波辐照载甲苯活性炭再生研究

研究在微波辐照条件下,活性炭量、微波功率、载气量、加热时间等因素对载甲苯活性炭脱附的影响,在正交实验中,各个影响因素的重要性排序为：氮气流量、活性炭量、辐照时间、微波功率,最佳的操作工况为：活性炭量9 g、载气流量300 mL/min、辐照时间120 s、微波功率500W,活性炭的脱附率在99.74%.     

活性炭吸附硫化氢及微波辐照解吸研究

研究了两种活性炭对硫化氢的平衡吸附性能力,并对活性炭床层的穿透性进行了考察;吸附饱和和活性炭在微波辐射的作用下进行解吸。实验表明,解吸效率与微波作用时间及温度有关,在本实验条件下H2S解吸效率达90．1％。     

应用活性炭再生含多环芳烃植物油的可行性及性能评价

为利用植物油去除污染土壤中的多环芳烃,研究了应用活性炭F400吸附柱再生含多环芳烃植物油的可行性,对含高浓度多环芳烃的植物油进行二级再生处理,优化了过程参数,比较了原植物油和经活性炭再生的植物油去除土壤中多环芳烃能力的差别.结果表明,活性炭吸附法可以实现含多环芳烃植物油的再生,证明了修复策略的可行性.二级处理可以进一步吸附植物油中的多环芳烃,且高分子量多环芳烃几乎完全被去除.再生植物油和原植物油去除土壤中多环芳烃的能力没有明显差别.     

Synergistic adsorption and advanced oxidation activated by persulfate for degradation of tetracycline hydrochloride using iron-modified spent bleaching earth carbon

At present, tetracycline hydrochloride (TCH) is a widely used antibiotic, and is often detected in water, posing a serious harm to human and ecological health. In this study, spent bleaching earth (SBE) was pyrolyzed to obtain spent bleaching earth carbon (SBE@C) and the nano Fe⁰/SBE@C prepared after zero-valent iron loading was adopted to remove TCH in water for the first time. The combination of nano Fe⁰/SBE@C and PS, the strong adsorption of SBE@C coupled with the oxidation of free radicals could achieve TCH efficient removal. The effects of nano Fe⁰ load, nano Fe⁰/SBE@C dosage, solution initial pH, and PS/TCH molar ratio on TCH removal efficiency in nano Fe⁰/SBE@C?+?PS system were studied. The results indicate that the optimal reaction conditions are 5% nano Fe⁰ load, 0.2 g/L nano Fe⁰/SBE@C dosage, initial pH of 3, PS/TCH molar ratio of 100:1. Under these conditions, TCH removal efficiency could reach 91%. Meanwhile, response surface methodology (RSM) was applied to predict optimal value of reaction conditions. The removal efficiency corresponding to the predicted optimal conditions was consistent with the actual removal efficiency obtained from the experiment. Moreover, six reaction systems were tested, and TCH removal efficiency in the SBE@C?+?PS system was 22.6%. When nano Fe⁰ was loaded on SBE@C, TCH removal efficiency in Fe⁰/SBE@C?+?PS system increased to 78.2%, in which TCH was first adsorbed on the surface of nano Fe⁰/SBE@C, and then was degraded by the oxidation of SO₄^?? and ?OH. Totally, the nano Fe⁰/SBE@C?+?PS system displayed excellent TCH removal efficiency, good stability and reusability, exhibiting a promise toward TCH removal.

     

Microwave regeneration of activated carbon used for removal of solvents from vented air

A microwave regeneration of activated carbon used to remove organic solvents from vented air has been investigated. Methyl ethyl ketone (MEK), acetone, and tetrachloroethylene (TCE) vapors were removed from vented air through adsorption onto granular activated carbon. The saturated carbon was then regenerated in a microwave field, where the solvent was quickly desorbed and recovered from the inner pores of the carbon granules. The microwave-induced regeneration restored the original adsorption capacity and surface area of the activated carbon.     

臭氧—生物活性炭工艺去除水中有机微污染物

在臭氧化的反应柱中填装陶粒滤料,构成了臭氧－陶粒→生物活性炭不深度净化流程,用该流程去除水中有机微污染物,ＣＯＤＭＮ去除率近近４０％,浊度和色度大大降低,色－质联机分析表明,原水中有机物由５８种降至３０种,潜在有毒有害物质由１３种减少到４种。     

强化活性炭处理工艺去除焦化厂生化出水中的氰化物

以某焦化厂生化出水为研究对象,考寨了金属负载活性炭(简称负载炭)和Fenton氧化预处理等强化活性炭工艺对总氰化物(TCN)的去除效果.在TCN批式实验中,对负载炭的金属离子种类和固定方式进行了考察,同时研究了接触时间、DO对游离氰(KCN配水)、络合氰(K3Fe(CN)6配水)及焦化厂生化出水中TCN的去除效果.结果表明,负载金属离子可以有效提高活性炭对TCN的去除量,KI固定后的载铜活性炭对TCN的去除更有效.吸附作用在活性炭去除TCN过程中起着主要作用,同时TCN在活性炭表面也发生缓慢的催化氧化反应.在穿透实验中,采用了小型炭柱穿透和微型快速穿透实验方法,得到的TCN穿透曲线基本相同.含不同比例原煤炭和负载炭的小型炭柱处理经Fenton氧化预处理的焦化厂生化出水时,在18 d的启动阶段后形成生物活性炭柱,其出水能长期达到<城镇污水处理厂污染物排放标准>(GB 18918-2002)规定的要求.载铜话性炭可以提高活性炭工艺对TCN的去除能力,确保处理全程(57 d)出水的TCN达标.     

Sorption of carbendazim and linuron from aqueous solutions with activated carbon produced from spent coffee grounds: Equilibrium,kinetic and thermodynamic approach

Spent coffee grounds (SCG) have been used for the production of activated carbon (AC) by impregnation with different ratios of phosphoric acid at 600?°C, Xp (H₃PO₄/coffee): 3:1^30%, 4:1^30%, 3:1^50% and 4:1^50%. The obtained AC was characterized by BET, FTIR and SEM. BET surface area corresponds to 803.422 m² g^?1. The influences of the main parameters such as contact time, the pesticides initial concentration, adsorbent dose, pH and temperature on the efficiency of separation process were investigated during the batch operational mode. Results were modeled by adsorption isotherms: Langmuir, Freundlich and Temkin isotherms, which gave satisfactory correlation coefficients. The maximum adsorption capacities calculated from the Langmuir isotherms were 11.918?mg g^?1 for carbendazim and 5.834?mg g^?1 for linuron at room temperature. Adsorption kinetics of carbendazim and linuron have been studied by the pseudo-first-order, the pseudo-second-order and the intraparticle diffusion model. The results of adsorption kinetics have been fitted the best by pseudo-second-order model. The resulted data from FTIR characterization pointed to the presence of many functional groups on the AC surface. SCG adsorbent, as an eco-friendly and low-cost material, showed high potential for the removal of carbendazim and linuron from aqueous solutions.     

Carbon consumption and regeneration of oxygen-containing functional groups on activated carbon for flue gas purification

Environmental Science and Pollution Research - High carbon consumption is an important factor restricting the wide application of activated carbon technology for flue gas purification. A fixed-bed...     

强化活性炭吸附技术深度处理焦化废水的可行性研究

采用混凝沉淀、活性炭吸附以及混凝沉淀 活性炭吸附工艺对焦化厂生化出水进行深度处理.单独混凝沉淀或活性炭吸附均可以将水样中COD降到100 mg/L以下,达到国家污水一级排放标准和冷却用水建议标准.活性炭根据不同的材质和进水而表现出不同的吸附性能,对于焦化厂生化出水,煤质炭Ⅰ和果壳炭均表现出良好的吸附效果,并使出水COD＜100 mg/L,但处理成本较高.混凝沉淀 活性炭吸附工艺充分发挥适合去除大分子污染物的混凝沉淀与适宜去除小分子污染物的活性炭吸附技术两者的协同增效作用,吸附单元采用廉价的煤质炭,使出水水质达到个别生产或生活用水回用标准,并且降低深度处理成本.研究结果表明,混凝沉淀 活性炭吸附作为焦化厂生化出水回用工艺是经济可行的.     

Development of an activated carbon impregnation process with iron oxide nanoparticles by green synthesis for diclofenac adsorption

The objective of this study was to impregnate the surface of palm coconut activated carbon with nanoparticles of iron compounds using Moringa oleifera leaf extracts and pomegranate leaf by a green synthesis method and to evaluate its adsorption capacity for sodium diclofenac. The adsorbent material was characterized by zeta potential, X-ray diffraction (XRD), N₂ adsorption/desorption (BET method), transmission electronic microscopy (TEM), and scanning electronic microscopy (SEM) coupled to dispersive energy spectrometry X-ray (EDX) methods. To evaluate the adsorption capacity of sodium diclofenac, the influence of pH, kinetics, isotherms, and thermodynamic properties were analysed. The impregnated adsorbents showed efficiency in the adsorption of sodium diclofenac. The kinetic model that best fit the experimental data was the pseudo-second-order model, and the equilibrium model was the Langmuir model. As for the thermodynamic study, it was verified that the adsorption reaction for all adsorbents occurs in a spontaneous, favourable way, and it is endothermic by physisorption. Therefore, this process is promising because it is a clean and non-toxic method when compared with chemical methods for the synthesis of nanoparticles.

     

Heterogeneous and homogeneous catalytic ozonation of benzothiazole promoted by activated carbon: kinetic approach

Ozone oxidation combined with activated carbon adsorption (O(3)/AC) has recently started to be developed as a single process for water and wastewater treatment. While a number of aspects of aqueous ozone decomposition are well understood, the importance and relationship between aqueous ozone decomposition and organic contaminant degradation in the presence of activated carbon is still not clear. This study focuses on determining the contribution of homogeneous and heterogeneous reactions to organic contaminants removal in O(3)/AC system. Benzothiazole (BT) was selected as a target organic pollutant due to its environmental concern. A reactor system based on a differential circular flow reactor composed by a 19 cm(3) activated carbon fixed bed column and 1 dm(3) storage tank was used. Ozone was produced from pure and dry oxygen using an Ozocav ozone generator rated at 5 g O(3)h(-1). Experimental results show that BT removal rate was proportional to activated carbon dosage. Activated carbon surface contribution to BT oxidation reactions with ozone, increased with pH in absence of radical scavengers. The radical reaction contribution within the pH range 2-11 accounted for 67-83% for BT removal in O(3)/AC simultaneous treatment. Results suggest that at pH higher than the pH of the point of zero charge of the activated carbon dissociated acid groups such as carboxylic acid anhydrides and carboxylic acids present on activated carbon surface could be responsible for the observed increase in the ozone decomposition reaction rate. A simplified mechanism and a kinetic scheme representing the contribution of homogeneous and heterogeneous reactions on BT ozonation in the presence of activated carbon is proposed.     

印制电路板酸性蚀刻废液的膜电解再生

高度精细化线路和高层数印制电路板产量的增加,导致酸性蚀刻废液的排放量越来越大,对环境的负荷也随之增大.介绍了酸性蚀刻废液膜电解再生的基本原理,进行了中试规模的应用研究,并与其他电解再生方法进行技术与经济比较分析.结果表明,在槽电压为5V、电解时间为2h的条件下,酸性蚀刻废液的氧化还原电位由480 mV升至540mV,所...     

TiO2/活性炭复合纳米纤维膜对亚甲基蓝的吸附研究

摘要以自制的TiO2/活性炭复合纳米纤维膜作为吸附剂,以亚甲基蓝为目标污染物,研究了亚甲基蓝初始浓度、温度、TiO2/活性炭复合纳米纤维膜投加量、pH等对TiO2/活性炭复合纳米纤维膜吸附去除亚甲基蓝的影响,并研究了TiO2/活性炭复合纳米纤维膜的Zeta电位、接触角、光催化再生性能.结果表明:(1)静态吸附时,随着亚...     

甲苯气体的动态吸附净化及吸附剂再生实验研究

研究了活性炭纤维(ACF)对甲苯气体的动态吸附净化过程及热空气解吸脱附再生过程.采用3种经验方程对ACF的吸附等温线进行拟合,其中Langmuir方程拟合效果最好,拟合相关系数R2 =0.9960,说明在给定的浓度范围内,ACF对甲苯的吸附是以单分子层吸附为主.穿透曲线实验表明,ACF对甲苯吸附效果较好,Yoon-Ne...     

采用零排放新工艺处理蚀刻废液

广州市某化工厂开发出一套对线路板蚀刻废液进行大规模集中资源化处理的零排放处理新工艺,该工艺通过在固相条件下生成氧化铜并用重力分选的方法将其分离出来,克服了原有工艺的缺陷,使废液中所有的成分能够在较低的处理成本下全部分离回收,无三废排出,达到了清洁生产的要求.对其工艺条件进行深入研究,通过正交试验优化了工艺条件.     

Catalytic oxidation of TNT by activated carbon

Activated carbon can remove 2,4,6-trinitrotoluene (TNT) and 1,3,5-trinitrobenzene (TNB) from aqueous solution and promote oxidation of TNT. After equilibrating a 0.35 mM TNT solution with activated carbon (0.2-1% w/v), HPLC and GC/MS analysis confirmed the presence of 2,4,6-trinitrobenzaldehyde (TNBAld) and 2,4,6-trinitrobenzene (TNB), and provided strong evidence supporting 2,4,6-trinitrobenzyl alcohol (TNBAlc) as an intermediate of TNT oxidation. After 6 d, TNT and its oxidation products were strongly bound to the activated carbon, while TNB was extractable with acetonitrile. Observations indicate that activated carbon catalyzes TNT oxidation to TNBAlc, which is readily oxidized to TNBAld and TNB in the absence of activated carbon under dark conditions. While adsorbed TNB was extractable with acetonitrile, activated carbon promoted rapid TNT oxidation and formation of unextractable residues. Strong binding is attributed to catalyzed oxidation of the TNT methyl group, probably through a free radical mechanism, and subsequent chemisorption of oligomers and polymerized products that are not desorbed from micropores. Our observations indicate TNT oxidation and bound residue formation after sorption by activated carbon increases the effectiveness of activated carbon to decontaminate water.