Chromium(VI) sorptive removal from aqueous solutions by nanocrystalline akaganèite

In this study, akaganeite (beta-FeO(OH)) an ironoxyhydroxide material, was used as a low-cost potential adsorbent for the removal of hexavalent chromium from aqueous solutions. The influence of agitation speed, solution pH, initial chromium concentration, sorbent concentration and temperature were evaluated at batch kinetic runs. It was shown that the solid diffusion model, in comparison to simple reaction kinetic models, described better the sorption kinetics. Freundlich and Frumkin isotherm best fitted the equilibrium results. Akaganeite presented a sorption capacity approximately 80 mg Cr(VI) g(-1), under the conditions studied. Flotation was used as a downstream process for the effective removal of the loaded material.     

Sorption of As(V) ions by akaganéite-type nanocrystals

A priority pollution problem, the removal of arsenate oxyanions from dilute aqueous solutions by sorption onto synthetic akaganéite (beta-FeO(OH)) was the aim of the present study. This is an innovative inorganic adsorbent material prepared in the laboratory, following a new method of preparation. The effect of akaganéite and arsenate concentration, the contact time, temperature, solution pH value, and ionic strength variation on the treatment process was mainly investigated during this study. Typical adsorption isotherms were determined, which were found to fit sufficiently the typical Langmuir equation. The mechanism of sorption was examined by electrokinetic, X-ray diffraction, Fourier transmission infrared and scanning electron microscopy measurements. Promising results were obtained, due to the favourite characteristics of the adsorbent applied.     

Mercury bioaccumulation and phytotoxicity in two wild plant species of Almadén area

Mercury is a widely distributed environmental pollutant, able to induce toxicity in living organisms, including higher plants. Some plant species are able to grow in mine sites, like the Almadén zone in Spain. Our study focus on two of these plant species, Rumex induratus and Marrubium vulgare and their responses to natural Hg exposure. Total Hg concentration in the soil below the plants could be classified as toxic, although the available fraction was low. Hg availability was higher for the M. vulgare than for the R. induratus plot. Hg concentrations in field plants of R. induratus and M. vulgare grown on these soils can be considered as phytotoxic, although no symptoms of Hg toxicity were observed in any of them. According to the BAF ([Hg]_tissue/[Hg]_avail), R. induratus showed a higher ability in Hg uptake and translocation to shoots, as well as higher concentrations of MDA and –SH:Hg ratios, so that this plant is more sensitive to Hg than M. vulgare. The resistance to Hg and the capability to extract Hg from the soil make both M. vulgare and R. induratus good candidates for Hg phytoremediation of contaminated soils.     

Efficient removal of nitrogen and phosphorus in aqueous solutions using modified water treatment residuals–sodium alginate beads

Environmental Science and Pollution Research - A high-performance sorbent, modified water treatment residuals–sodium alginate beads (WTR-SA beads), was prepared through a series of salt and...     

Residue behavior of etoxazole under field conditions in Egypt and estimation of processing factors during the production of strawberry juice and purée

Abstract

The degradation under field conditions and the residue behavior of etoxazole during juicing and purée making was evaluated. Etoxazole residues were determined by HPLC-UV at six different Pre Harvest Intervals (PHIs) as to estimate the degradation of residue in fruits. Samples with significant residues were processed and residue were determined after juicing and purée making. The effect of washing was also estimated. Processing Factors (PFs) for etoxazole after each step were less than 1 and the PFs of the overall processes were lower than 0.85 for washing fruits, 0.13 for juice and 0.04 for purée. The studied processes could obviously reduce the pesticide residues that are present in the raw strawberries. Uncertainties in the use of the PFs were identified due to the potential formation of metabolites during the processes.     

Toxicity of cigarette butts and possible recycling solutions—a literature review

Environmental Science and Pollution Research - Tobacco is a worldwide-consumed product, which in addition to causing public health-related issues is responsible for the most common form of litter...     

Determination of T‐2 toxin in grain and grain products by HPLC and TLC

Abstract

The purpose of this study was to investigate the T‐2 toxin contaminated grain and grain products consumed especially by Turkish population. The T‐2 toxin was detected using the high performance liquid chromatography (HPLC) with UV detector at 208 nm and the identify of T‐2 was further confirmed by thin layer chromatography (TLC). The recovery was 91 ±4.24% for corn flour fortified with the known amount of T‐2 toxin (1 ppm). The detection limits of T‐2 toxin for the HPLC and the TLC were 25 ng and 50 ng, respectively. A total of 30 commercially available grain and grain product samples were analyzed. Two corn flour samples were found to contain detectable levels of T‐2 toxin at a level of 1.60 ppm and 4.08 ppm.     

Characterization of atmospheric aerosols by SEM in a rural area in the western part of México and its relation with different pollution sources

Samples of particulate matter were collected during the period from October 2006 through September 2007 in a rural station located 12 km from the city of Colima. A total of 3600 particles were analyzed by SEM-EDS and then classified by their chemical composition and morphology in order of abundance: those rich in C, Fe, Si–Al, Cl–Na, Ca, Ba; and to a lesser abundance, particles rich in heavy metals such as Pb and V–Ni were observed. A factorial analysis was carried out to determine the main elements related with the emission sources such as crustal/farming; fuel-oil; marine; volcanic activity and industry. Trough the seasons, the dominant winds causes the presence of anthropogenic particles in the rural site. The information presented in this study aims to give insight and detailed of the analysis of the morphological characteristics and chemical composition of atmospheric particles at individual level in a rural site from Colima State, Mexico.     

Study of turbulent diffusion above and within a forest—application in the case of SO2

Some results concerning characteristics of airflow within and above a forest are presented: horizontal mean windspeed profiles, turbulence intensities, turbulent transfer coefficients, autocorrelation curves, energy spectra, turbulence scales, microscales.To understand the mechanisms of SO₂ diffusion within and above a forest, we have to calculate SO₂ fluxes at the top of the canopy and two methods are used for this: the first one uses speed fluctuations and the second one mean speed values.The aim of that work is to determine the behaviour of the forest towards SO₂ and to develop a diffusion model of SO₂ with associated absorption by the roughness.     

Mathematical modelling of dispersion and chemical reactions in a plume — oxidation of no to NO2 in the plume of a power plant

A mathematical model is presented for the dispersion and chemical reactions of pollutants in chimney plumes. It assumes that atmospheric dispersion is such that an inert constituent would be distributed in a Gaussian fashion downwind of the chimney, uses a discreet approximation approach to obtain concentrations of reactive pollutants, and can account for reactive species entrained into the plume from the ambient air. The model is used to interpret some data on NO₂ formation in the plume of a power plant chimney.     

Roles of regional hydrodynamic and trophic contamination in cadmium bioaccumulation by Pacific oysters in the Marennes-Oléron Bay (France)

The Marennes-Oléron Bay, hosting the largest oyster production in France, is influenced by the historic polymetallic pollution of the Gironde Estuary. Despite management efforts and decreasing emissions in the Gironde watershed, cadmium levels in oysters from the bay are close to the consumption limit (5 μg g⁻¹ dw, EC). From mid April to mid July 2009, we investigated the role of tidal resuspension and regional hydrodynamics on Cd speciation (seawater, SPM, phytoplankton, sediment, microphytobenthos) and bioaccumulation in 18 month-old oysters (gills, digestive glands, rests of tissues) reared under natural conditions (i) at ∼60 cm above the sediment and (ii) on the sediment surface. Dissolved and particulate Cd concentrations in surface and bottom waters were similar and constant over tidal cycle suggesting the absence of Cd release during sediment resuspension. Temporal dissolved and particulate Cd concentrations were closely related to Gironde Estuary water discharges, showing increasing concentrations during flood situations and decreasing concentrations afterwards. Cd depletion in the water column was associated with increasing Cd in the [20-100 μm] plankton fraction, suggesting Cd bioaccumulation. After 3 months, enrichment factors of Cd in tissues of oysters exposed in the water column and directly on the sediment were respectively 3.0 and 2.2 in gills, 4.7 and 3.2 in digestive glands and 4.9 and 3.4 in remaining tissues. Increasing Cd bioaccumulation in gills, digestive glands and remaining tissues can be related to elevated dissolved Cd in the bay, suggesting gill contamination via the direct pathway and subsequent internal redistribution of Cd to other organs and tissues. Elevated Cd contents in oysters reared on tables could be attributed to different trophic Cd transfer (phytoplankton versus microphytobenthos) or to different oyster metabolisms between the rearing conditions as suggested by metallothionein concentrations.     

Biodegradation of α and β isomers of endosulphan and endosulphan sulphate in Indian soils

Abstract

The degradation of α and β isomers of endosulphan and endosulphan sulphate in four sterilized and non sterilized Indian soils under laboratory conditions was studied. Degradation was found to be more in non‐sterilized as compared to the sterilized soil. The half life of α‐endosulphan, β‐endosulphan and endosulphan sulphate was found to be 136.8, 273 and 301 days in sterilized Alfisol and 55, 256 and 277 days in non‐sterilized Alfisol, respectively. α‐Endosulphan degraded more readily than β‐endosulphan and endosulphan sulphate under both sterilized and non‐sterilized soil conditions.     

Sorption of lead in soil as a function of pH: a study case in México

Reactions of lead sorption onto soil are largely affected by properties and composition of soil and its solution. In this study, the lead sorption onto regosol eutric soil from Francisco I. Madero, Zacatecas, Mexico is evaluated at different pH values. Soil samples were suspended in lead solutions of 10, 25, 50, 100, 150, 200, 300, and 400 mg/l (as Pb(NO3)2). The pH was adjusted at 2, 3, 4, and 5.5 with nitric acid for each of the lead solution concentrations. In all the cases the ionic strength was I=0.09 M with calcium nitrate. The solid-liquid-ratios were fixed in 1:100 and 1:200 g/ml. The results show that lead sorption increases when pH increases. Experimental isotherms were adjusted by both Langmuir and Freundlich models. The Langmuir affinity parameter, K, indicates that the lead sorption capacity of Francisco I. Madero soils is largely perceptible to pH changes.     

Magnetic photocatalysts from δ-FeOOH and TiO2 and application in reactions for degradation of methylene blue and paracetamol with UV-C and sunlight

Environmental Science and Pollution Research - Water contamination is a common problem, especially considering dyes and drugs disposal. A possible and effective treatment method to remove these...     

Behaviour and variability of local and regional oxidant levels (OX = O3 + NO2) measured in a polluted area in central-southern of Iberian Peninsula

The purpose of this work is to contribute to the understanding of the photochemical air pollution in central-southern of the Iberian Peninsula, analysing the behaviour and variability of oxidant levels (OX?=?O₃?+?NO₂), measured in a polluted area with the highest concentration of heavy industry in central Spain. A detailed air pollution database was observed from two monitoring stations. The data period used was 2008 and 2009, around 210,000 data, selected for its pollution and meteorological statistics, which are very representative of the region. Data were collected every 15 min, however hourly values were used to analyse the seasonal and daily ozone, NO, NO₂ and OX cycles. The variation of OX concentrations with NO _x is investigated, for the first time, in the centre of the Iberian Peninsula. The concentration of OX was calculated using the sum of a NO _x -independent ‘regional’ contribution (i.e. the O₃ background), and a linearly NO _x -dependent ‘local’ contribution. Monthly dependence of regional and local OX concentration was observed to determine when the maximum values may be expected. The variation of OX concentrations with levels of NO _x was also measured, in order to pinpoint the atmospheric sources of OX in the polluted areas. The ratios [NO₂]/[OX] and [NO₂]/[NO _x ] vs. [NO _x ] were analysed to find the fraction of OX in the form of NO₂, and the possible source of the local NO _x -dependent contribution, respectively. The progressive increase of the ratio [NO₂]/[OX] with [NO _x ] observed shows a greater proportion of OX in the form of NO₂ as the level of NO _x increases. The higher measured values in the ratio [NO₂]/[NO _x ] should not be attributed to NO _x emissions by vehicles; they could be explained by industrial emission, termolecular reactions or formaldehyde and HONO directly emitted by vehicles exhausts. We also estimate the rate of NO₂ photolysis, J _NO2?=?0.18–0.64 min^?1, a key atmospheric reaction that influence O₃ production and then the regional air quality. The first surface plot study of annual variation of the daily mean oxidant levels, obtained for this polluted area may be used to improve the atmospheric photochemical dynamic in this region of the Iberian Peninsula where there are undeniable air quality problems.     

The spatial distribution dynamic and convergence of CO2 emissions in Iran’s provinces

Environmental Science and Pollution Research - It is essential to study CO2 emissions intensity as the most critical factor affecting temperature increase and climate change in a country like Iran,...     

Impact of δ-MnO2 on the chemical speciation and fractionation of Cr(III) in contaminated soils

Environmental Science and Pollution Research - Oxidation of Cr(III) by birnessite (δ-MnO2) was an important geochemical reaction determining the toxicity and mobility of dissolved Cr(III) in...     

Comparative receptor modelling study of TSP,PM2 and PM2−10 in Ho Chi Minh City

Elemental compositions were measured for TSP (total suspended particulate matter), PM₂₋₁₀ and PM₂ (particulate matter with aerodynamic diameters from 2 to 10 μm and less than 2 μm, respectively) in Ho Chi Minh City. Concentrations of 23 elements and particulate mass (PM) were used for receptor modelling to identify and quantify aerosol sources using principal component factor analysis (PCFA). A suite of factors containing similar elements with significant factor loadings were revealed among the factor matrices, thus facilitating the identification of common sources for different aerosol types. These sources include vehicular emissions (Br and Zn), coal burning (Se), industrial processes (Ce, Co, Cr, Pb and Sb), road dust (Al, Ti, V), soil dust (Fe and Th) and biomass burning (K). Marine aerosols (Na and Cl) and mineral fly ash (Sc and La) were revealed only in the PM₂₋₁₀ model. For TSP, the last four sources are combined in one factor. The last (9th) factor in the PM₂ model, characterised by a high loading from PM and insignificant loadings from elements, was attributed to secondary sulphates and organics, although these constituents were not measured in the experiments. Such a remarkable source identification capability of the modelling technique highlights the significance of achieving an optimal factor solution as a crucial step in PCFA, that was done by systematically varying the number of factors retained and carefully evaluating each factor matrix for both model fitting performance and physical reasonableness.